A NOVEL WIDEBAND ANTENNA DESIGN USING U-SLOT

U-slot patch antennas with ∏-shaped feed slot are studied,and numerical results based on the FDTD method are presented. The effects of varying physical parameters are investigated with a goal of understanding the coupling among different resonators. It is found that the U-slot patch antenna can be designed to attain 50% impedance bandwidth as well as 30-40% gain bandwidth. By altering the sizes of U-slot and feed slot,the wideband characteristic can be changed into a dual-frequency char-acteristic.

AN ULTRA-WIDEBAND ANTENNA FOR THE REINFORCED CONCRETE DETECTION

In this paper,an Ultra-Wideband(UWB) planar antenna is proposed for the reinforced concrete detection,which consists of a pair of planar waterdrop arms,a microstrip to coplanar parallel-strips transition and a shallow rectangular cavity.In order to overcome the disadvantages of the shallow cavity,some absorbing material is loaded to weaken the narrow-band effect of the cavity and the crosstalk interference.The simulated and measured results show that the proposed antenna has a large bandwidth from 0.48 GHz to 3.6 GHz with Voltage Standing Wave Ratio(VSWR) below 2 and a fractional bandwidth about 200% under the center frequency of 1.6 GHz,directional radiation characteristics and small late-time ringing in the time domain,which can be suitable for nondestructive detection of the reinforced concrete.

Experimental Study of On-Body Radio Channel Performance of a Compact Ultra Wideband Antenna

In this paper, on-body radio channel performance of a compact ultra wideband (UWB) antenna is investigated for body-centric wireless communications. Measurement campaigns were first done in the chamber and then repeated in an indoor environment for comparison. The path loss parameter for eight different on-body radio channels has been characterized and analyzed. In addition, the path loss was modeled as a function of distance for 34 different receiver locations for propagation along the front part of the body. Results and analysis show that, compared with anechoic chamber, a reduction of 16.34% path loss exponent is noticed in indoor environment. The antenna shows very good on-body radio channel performance and will be a suitable candidate for future efficient and reliable body-centric wireless communications.

An ultra-wideband pattern reconflgurable antenna based on graphene coating

An ultra-wideband pattern reconfigurable antenna is proposed.The antenna is a dielectric coaxial hollow monopole with a cylindrical graphene-based impedance surface coating.It consists of a graphene sheet coated onto the inner surface of a cylindrical substrate and a set of independent polysilicon DC gating pads mounted on the outside of the cylindrical substrate.By changing the DC bias voltages to the different gating pads,the surface impedance of the graphene coating can be freely controlled.Due to the tunability of graphene＇s surface impedance,the radiation pattern of the proposed antenna can be reconfigured.A transmission line method is used to illustrate the physical mechanism of the proposed antenna.The results show that the proposed antenna can reconfigure its radiation pattern in the omnidirectional mode with the relative bandwidth of 58.5% and the directional mode over the entire azimuth plane with the relative bandwidth of 67%.

Wideband dipole antenna with inter-digital capacitor

A dipole antenna with wideband characteristics is presented. The proposed antenna consists of a dipole with periodic capacitive loading and a pair of coplanar striplines （CPSs） as an impedance transformer. By adding interlaced coupling lines at each section, periodic capacitive loading is realized. The periodic interlaced coupling lines divide each arm of the dipole into five sections, and currents are distributed on different sections at different frequencies, which is useful to achieve a wide impedance bandwidth. By parametric study using HFSS, the optimized parameters of this dipole antenna are obtained. In order to validate the simulation results, a prototype of the proposed dipole antenna is fabricated and tested. The results show that the proposed antenna can achieve a gain of 3.1 dB–5.1 dB and bandwidth of 51% for ｜S 11 ｜ 10 dB over the band of 3.9 GHz–6.6 GHz, indicating its good radiation performance and radiation efficiency.

Ultra-wideband printed antennas for communication applications

A new type of ultra-wideband （UWB） printed monopole antennas is presented, which is composed of a circular or armular patch and a trapeziform ground plane with a tapered CPW feeder in the middle. Both simulated and experimental results are presented, showing good agreement and therefore verifying validity of the design. The proposed antenna with a circular monopole patch achieves an 11.6： 1 measured ratio bandwidth of VSWR ≤2 （ from 0,79 GHz to 9.16 GHz）, while that with an annular patch obtains a measured ratio impedance bandwidth of 10.6：1 （from 0.87 GHz to 9.47 GHz）. In addition, these designs exhibit nearly omnidirectional radiation patterns with simple compact structures, which axe attractive in communications and others UWB applications.

Progress in ultra-wideband planar antennas

This paper introduces the advances of ultra-wideband （UWB） and super-wideband （SWB） planar antennas based on the printed monopole, microstrip slot and other planar antenna designs in the last decade. A brief history of the ultrawideband antennas is first provided. Several types of planar antennas for UWB systems with band-notched designs are reviewed. Special SWB planar antenna designs with the bandwidth ratio greater than 10：1 including metal-plate and printed monopole antennas and tapered slot antennas are presented and compared.

A Novel Ultra-Wideband Monopole Antenna with Band-Stop Characteristic

In this letter, a simple monopole antenna with variable band-notched characteristic for ultra wide band (UWB) function is proposed. Two L-shaped quarter-waveguide resonators coupled to the ground plane with two shorting tracks at the sides of the antenna are used to generate stop-band performance around 5.5 GHz (WLAN). The proposed antenna is fabricated on the substrate FR4 (relative permittivity of 4.7) and has a compact size of 16 × 28.5 × 1.6 mm. The designed antenna has a good impedance matching in 3.1 - 11.4 GHz frequency range with VSWR < 2, except the band 5 - 5.85 GHz.

Wideband Sierpinski Carpet Fractal Shaped Cylindrical Dielectric Resonator Antenna for X-Band Application

In this paper, a wideband Sierpinski carpet patterned cylindrical Dielectric Resonator Antenna (DRA) operating in the X-Band is proposed. This DRA is realized from low cost Teflon. An impedance bandwidth of 50% is obtained cove- ring the entire X-band with similar radiation pattern throughout the band. The average peak gain within the band is about 5.5 dBi.

Wideband Polarization Reconfigurable Dielectric Resonator Antenna

A wideband polarization reconfigurable dielectric resonator antenna excited by quasilumped quadrature coupler（ QLQC） is proposed. By adjusting the value of varactor diode on the QLQC feed network,both the wideband LP and CP dielectric resonator antennas（ DRA） modes can be achieved. By selecting a different feed port,left-and right-handed CP conversion can be realized.It is found that the 10 dB impedance bandwidth of the LP and CP modes are 10. 1% and 44. 9%,respectively.For the CP mode,a very wide 3 dB axial ratio bandwidth of 37. 7% can be obtained which is much larger than that of the microstrip patch counterpart（ 3. 8%）. It is worth mentioning that the wideband CP DRA has a stable broadside radiation pattern across the whole operating band where the boresight gain is larger than 3 dBi.

A NOVEL ULTRA WIDEBAND MONOPOLE ANTENNA WITH BAND-NOTCHED CHARACTERISTICS

A simple and compact microstrip-fed Ultra WideBand(UWB) printed monopole antenna with band-notched characteristic is proposed in this paper.The antenna is composed of a square ring with a small strip bar,so that the antenna occupies about 7.69 GHz bandwidth covering 3.11～10.8 GHz with expected band rejection from 5.12 GHz to 5.87 GHz.A quasi-omnidirectional and quasi-sym-metrical radiation pattern is also obtained.This kind of band-notched UWB antenna requires no ex-ternal filters and thus greatly simplifies the system design of UWB wireless communication.

Ultra-Wideband Design of the Wire Conical Antenna

Using the wire construction technique, a conical monopole antenna is fabricated. With the method of moments, the dependences of the voltage standing wave ratio （VSWR） on the number of the trapezoid wire elements, conical angles, wire radius, etc. are investigated. The calculation and the experiment show that the designed wire conical antenna has the ultra-wideband property and can be used for the engineering.

Design of a low-sidelobe-level and wideband dielectric resonator antenna array for 60 GHz millimeter wave communication

A low-sidelobe-level( SLL) and wideband linear dielectric resonator antenna( DRA) array is proposed for 60 GHz millimeter wave communication. The array consists of 10 wideband DRAs which work at 60 GHz and it is fed by a Chebyshev feeding network to get a low SLL. To avoid the influence from the feeding network,a U-shaped substrate and a conformal ground are used,which can separate the DRA array and the feeding network. The parameter analysis and simulated results are presented.

基于半圆分形的柔性超宽带天线

以柔性材料聚酰亚胺(PI)作为介质基板材料,设计了一种柔性超宽带(UWB)半圆分形天线。天线辐射单元采用四阶半圆迭代嵌套分形结构,通过不同分形半圆调节电长度,增加天线的工作谐振点。通过在接地板开槽提高天线的阻抗匹配特性,实现UWB辐射。利用共面波导馈电方式提高天线的集成性。仿真与测试结果表明:所设计天线的阻抗带宽为2.98-10.61 GHz,带内全向增益达到5.58 dBi,天线最终尺寸为30 mm×24 mm,实现了小型化和可弯曲的特性,在共形于13 mm半径的圆柱后,天线仍能保持UWB辐射性能。

Ultra-Wideband Log Periodic Dipole Antenna (LPDA) for Wireless Communication Applications

This paper proposes a printed log-periodic dipole antenna (LPDA) for ultra wide bandwidth (UWB) applications. The antenna comprises of cascading four U shaped elements of different line lengths with balun circuit to improve the antenna impedance matching. The proposed antenna dimensions are 50 × 50 mm2 with FR4 substrate thickness 0.8 mm. Full-wave EM solver HFSS (High Frequency Structure Simulator) is used for modeling the proposed antenna. The pulse distortion is verified by the measured the proposed antenna performance with virtually steady group delay. The simulation and experimental results show that the proposed antenna exhibits good impedance matching, stable radiation patterns throughout the whole operating frequency bands, acceptable gain and stable group delay over the entire operating band. An UWB extended from 1.85 GHz to 11 GHz is obtained, and the average antenna gain is about 5.5 dBi over the operating band with peak gain around 6.5 dBi and 70% average radiation efficiency.

3D打印技术在机载超宽带共形天线中的应用研究

为提高共形相控阵天线的设计制造效率,在平面紧耦合天线的基础上,设计了与飞机襟翼曲面共形的紧耦合超宽带相控阵天线。按照共形天线的安装要求,提出了混合3D打印技术,即采用熔融堆积成型技术及微滴喷射成型技术实现襟翼流线型曲面模型的打印,并完成了紧耦合天线辐射层的打印,验证了3D打印技术在共形天线上的应用。加上馈电结构后对单元电压驻波比(voltage standing wave ratio, VSWR)和方向图进行了测试,结果表明所设计的天线在0.4~2.0 GHz范围内,VSWR、单元方向图和阵列方向图符合设计技术指标,为后续共形天线设计和加工提供了技术基础。

基于层间耦合的宽带毫米波超表面天线

通信技术快速发展,对高速、大容量通信需求迫切。然而,传统频谱资源受限,难以满足需求,毫米波天线备受瞩目。本研究旨在改善传统微带贴片天线的带宽和增益问题。通过加载超表面结构和加强层间耦合的方法,设计了24~50 GHz宽带毫米波超表面天线。该天线采用层压方式将超表面加载在介质层中,通过仿真分析了超表面参数对天线带宽的影响,从而确定最佳天线结构尺寸,并进行了天线的制作和性能测试。仿真和实测结果表明,该天线能够实现24~50 GHz的宽带,相比传统贴片天线,其带宽增加了52.23%,并具有良好的辐射特性和增益性能。该宽带毫米波超表面天线在宽频段通信、5G通信等领域具备广阔的应用前景。

基于特征模理论分析的超宽带小型化准八木天线设计

文中设计了一款超宽带准八木天线。根据特征模理论对传统的准八木天线进行分析,并结合天线理论,在不改变天线原有尺寸的情况下,通过采用弯折、切槽等技术,增大了电流路径,拓宽了低频的工作带宽。天线尺寸为0.256λ_(0)×0.256λ_(0)×0.002λ_(0)(λ_(0)为最小工作频率所对应的波长),工作带宽为0.78 GHz~1.58 GHz。与初始天线相比,相对带宽从32.0%提高至67.8%。通过前后比可以看出,天线具有良好的定向性能,可以满足人脑探测活动的需求。

采用螺旋线实现高隔离度的车载多频宽带MIMO天线

为解决车载天线工作带宽窄和MIMO天线低频段隔离度低等问题,提出一种应用于车载通信系统的多频宽带高隔离度的MIMO天线,其工作频段为824~960 MHz和1710~6000 MHz,可覆盖民用移动通信的2G/3G/4G/5G和无线局域网/车联网等频段。单极子天线单元采用弯曲、开槽等诸多技术实现多频宽带,还通过添加接地枝节来降低天线高度和提高物理稳定性;在MIMO天线设计上采用螺旋线来提高天线单元之间的隔离度。实测结果表明,天线在工作频段内的反射系数小于-10 dB,隔离度小于-20 dB,低频段增益和辐射效率略低,中高频段的增益均大于4 dBi,最高达到7 dBi,效率均高于70%,最高可以达到96%。实测数据与仿真数据具有良好的一致性,所研制的天线可满足车载天线对多频段通信和高隔离度MIMO天线的技术要求,其结构和尺寸专为安装于汽车内部中控台背面而设计。

一种超宽带双陷波可穿戴天线设计

基于牛仔布柔性材料,设计了一种小型化双陷波超宽带可穿戴天线。天线由牛仔布料基板、开槽单极子辐射贴片和缺陷地平面构成,具有超宽带特性,能覆盖3.1~10.6GHz的超宽带频段范围。通过在天线接地板刻蚀两条新型蜿蜒形槽和在单极子辐射贴片上添加对称枝节以实现双陷波特性。该天线结构紧凑,尺寸仅为24mm×28mm×0.84mm。仿真的-10dB天线工作带宽为143.7%(2.95~18GHz),并且天线在3.24~3.87GHz和5.11~5.91GHz频段内具有双陷波特性,能有效抑制全球微波互联接入系统(WiMAX)和无线局域网(WLAN)频段的干扰。此外,对天线的可弯曲性、辐射性能以及人体安全性能进行了分析。测试与仿真结果基本一致,表明该天线可用于可穿戴系统中。