YIELD SURFACES AND PLASTIC FLOW OF 45 STEEL UNDER TENSION-TORSION LOADING PATHS

An experimental analysis on the subsequent yield-surfaces evolution using multiple specimens is presented for a 45 steel after a prescribed pre-strain loading in three different directions respectively, and the yielding is defined by a designated offsetting strain. The size of the subsequent yield surface is found smaller than the initial yield surface; the negative cross effects are observed in the normal loading direction, its shape is not a Mises circle but has a rather blunt nose in loading direction and flat in the opposite. These results strongly depend on the loading path and the prescribed offset plastic strain. The plastic flow direction to the subsequent yield surface is investigated, and it is found that the plastic flow direction deviates from the normal flow rule. The deviation differs from preloading case to preloading case. And the plastic flow direction would have a larger deviation from the normal of the yield surface, if the subsequent yield was defined by a smaller offset strain. Furthermore, the experiments are simulated using the Chaboche model, and the results show that it can rationally predict yield-surface only when yield is defined by a fairly large offset strain.

Surface Yielding of Metals by X-ray Diffraction

Surface yielding of metallic material was measured with strain gage and X-ray diffraction methods. The results show that.when the residual stress in the transverse direction is involved,the surface yield strength should be evaluated with biaxial Mises criterion.For a medium carbon high strength steel, the yield strength of the bulk material is 581 MPa and the surface yield strengths for 0.05% and 0.1%plastic strain are about 436 MPa and 463 MPa respectively.The 0.05% yield strength will approximately increase to 788 MPa after shot peening.In the early stage of plastic deformation, strain hardening in the surface layer is quite different from that of the bulk sample.

SURFACE YIELD STRENGTH AND FATIGUE LIMIT FOR STEELS

The surface yield strength(σ_(ms))for various carbon steels was studied by means of X-ray diffraction method.The results showed that it is.far below the bulk yield strength,and is the resistance against plastic deformation in the surface layer.The smooth fatigue limit is associ- ated with crack initiation which is a result of accumulation of plastic deformation.Experimen- tal results showed the relation of smooth fatigue limit for 50% survival with σ_(ms)is σ_(ms)=0.81 tO 1.02 σ_(-1)for different steels.The smooth fatigue limit of a medium carbon steel for 99.9% survival with σ_(ms)is σ_(ms)=0.98 tO 1.10 σ_(-1).It is less expensive and time consuming to measure σ_(ms)than σ_(-1).

A thermodynamic-based model for modeling thermo-elastoplastic behaviors of saturated clayey soils considering bound water dehydration

The non-isothermal deformation of soft mudrocks or clay soils is one of the most critical issues in energy and environmental related geotechnics.Clay-related geomaterials hold complex microstructure and mineral composition,which brings difficulty in investigating their thermo-mechanical behaviors.Previous studies pay little attention to the difference between a thermal plastic strain and the strain from clay dehydration.In this study,a new constitutive model is proposed for describing the thermoelastoplastic behaviors of clayey soils under water-saturated condition.The effect of temperature variation and mechanical loading on elastoplastic strains and dehydration are investigated.The thermodynamics laws and the unconventional plasticity are applied to quantify the thermo-mechanical behavior.The irreversible strain is captured by using Cam-Clay plasticity and subloading yield surface concept.The dehydration strain is described by utilizing a novel method based on generalized thermodynamics approach and Helmholtz free energy function.The internal variables,and the first and second laws of thermodynamics are applied in the model.The hardening rule is established by implementing the laws of physical conservation,energy dissipation,and plastic flow.The proposed model is validated using specially designed thermal consolidation tests on laboratory prepared heavily consolidated clayey soils and some published data of clayey soils with different geological origins.

Normalized fatigue properties of asphalt mixture at various temperatures

This study normalized the mixture's fatigue behavior at various temperatures,and the strength and fatigue tests of the mixture were conducted.The stress state of the asphalt mixture includes direct tensile,uniaxial compression,and indirect tensile.The Desai yield surface and fatigue path were proposed.And a normalized fatigue characteristics model of the mixture was established.The following conclusions were obtained.With the increases in the loading rate,the strength of the asphalt mixture increased.As the temperature increases,the strength of the mixture is reduced.At various temperatures and rates,the strength forms a closed curved surface.The Desai strength yield surface was established,which forms a closed curved surface.When the loading rate and temperature are below a certain critical line,the asphalt mixture will not undergo strength damage.At a fixed stress state,the fatigue damage path of the mixture was determined.The stress ratio was determined considering the influence of the loading rate.In this way,a normalized model can be described to express the asphalt mixture fatigue properties at various temperatures and stress levels.For the asphalt mixture in an indirect tensile state,the normalized fatigue equation parameter is 4.09.This model is more suitable for reflecting the viscous-elastic behavior of the mixtures than the fatigue equation determined by the notional stress ratio.

Review of collapse triggering mechanism of collapsible soils due towetting

Loess soil deposits are widely distributed in arid and semi-arid regions and constitute about 10% of land area of the world.These soils typically have a loose honeycomb-type meta-stable structure that is susceptible to a large reduction in total volume or collapse upon wetting.Collapse characteristics contribute to various problems to infrastructures that are constructed on loess soils.For this reason,collapse triggering mechanism for loess soils has been of significant interest for researchers and practitioners all over the world.This paper aims at providing a state-of-the-art review on collapse mechanism with special reference to loess soil deposits.The collapse mechanism studies are summarized under three different categories,i.e.traditional approaches,microstructure approach,and soil mechanics-based approaches.The traditional and microstructure approaches for interpreting the collapse behavior are comprehensively summarized and critically reviewed based on the experimental results from the literature.The soil mechanics-based approaches proposed based on the experimental results of both compacted soils and natural loess soils are reviewed highlighting their strengths and limitations for estimating the collapse behavior.Simpler soil mechanics-based approaches with less parameters or parameters that are easy-to-determine from conventional tests are suggested for future research to better understand the collapse behavior of natural loess soils.Such studies would be more valuable for use in conventional geotechnical engineering practice applications.

AN EQUIVALENT CONTINUUM METHOD OF LATTICE STRUCTURES

An equivalent continuum method is developed to analyze the effective stiffness of three-dimensional stretching dominated lattice materials. The strength and three-dimensional plastic yield surfaces are calculated for the equivalent continuum. A yielding model is formulated and compared with the results of other models. The bedding-in effect is considered to include the compliance of the lattice joints. The predicted stiffness and strength are in good agreement with the experimental data, validating the present model in the prediction of the mechanical properties of stretching dominated lattice structures.

MULTIAXIAL BEHAVIOR OF NANOPOROUS SINGLE CRYSTAL COPPER:A MOLECULAR DYNAMICS STUDY

The stress-strain behavior and copper are studied by the molecular dynamics incipient yield surface of nanoporous single crystal （MD） method. The problem is modeled by a periodic unit cell subject to multi-axial loading. The loading induced defect evolution is explored. The incipient yield surfaces are found to be tension-compression asymmetric. For a given void volume fraction, apparent size effects in the yield surface are predicted： the smaller behaves stronger. The evolution pattern of defects （i.e., dislocation and stacking faults） is insensitive to the model size and void volume fraction. However, it is loading path dependent. Squared prismatic dislocation loops dominate the incipient yielding under hydrostatic tension while stacking-faults are the primary defects for hydrostatic compression and uniaxial tension/compression.

On the homogenization of metal matrix composites using strain gradient plasticity

The homogenized response of metal matrix composites（MMC） is studied using strain gradient plasticity.The material model employed is a rate independent formulation of energetic strain gradient plasticity at the micro scale and conventional rate independent plasticity at the macro scale. Free energy inside the micro structure is included due to the elastic strains and plastic strain gradients. A unit cell containing a circular elastic fiber is analyzed under macroscopic simple shear in addition to transverse and longitudinal loading. The analyses are carried out under generalized plane strain condition. Micro-macro homogenization is performed observing the Hill-Mandel energy condition,and overall loading is considered such that the homogenized higher order terms vanish. The results highlight the intrinsic size-effects as well as the effect of fiber volume fraction on the overall response curves, plastic strain distributions and homogenized yield surfaces under different loading conditions. It is concluded that composites with smaller reinforcement size have larger initial yield surfaces and furthermore,they exhibit more kinematic hardening.

A MICROMECHANICAL MODEL FOR γ-TiAl BASE PST CRYSTALS

An analytical micromechanical method is proposed to examine the dependence of plastic deformation on the microstructure for a PST crystal. The sub-domain microstructure of the γ phase and the effect of the α2 phase are taken into account by a proper micromechanical formulation, the dislocation slip and twinning deformation mechanisms are considered in the context of crystal plasticity. The model can well predict the dependence of stress-strain relations on loading angle with respect to the microstructure. The influence of the twinning and lamellar spacing on the deformation behavior and biaxial yield surfaces for PST crystals are also examined.

PLASTIC ZONE OF SEMI-INFINITE CRACK IN PLANAR KAGOME AND TRIANGULAR LATTICES

The fracture investigations of the planar lattices made of ductile cell walls are currently limited to bending-dominated hexagonal honeycomb. In this paper, the plastic zones of stretching-dominated lattices, including Kagome and triangular lattices, are estimated by analyzing their effective yield loci. The normalized in-plane yield loci of these two lattices are almost identical convex curves enclosed by 4 straight lines, which is almost independent of the relative density but is highly sensitive to the principal stress directions. Therefore, the plastic zones around the crack tip of Kagome and triangular are estimated to be quite different to those of the continuum solid and also hexagonal lattice. The plastic zones predictions by convex yield surfaces of both lattices are validated by FE calculations, although the shear lag region caused by non-local bending effect in the Kagome lattice enlarges the plastic zone in cases of small ratio of rp/l.

An economic assessment of the health effects and crop yield losses caused by air pollution in China's Mainland

Air pollution is severe in China, and pollutants such as PM2.5 and surface 03 may cause major damage to human health and crops, respectively. Few studies have considered the health effects of PM2.5 or the loss of crop yields due to surface 03 using model-simulated air pollution data in China. We used gridded outputs from the WRF-Chem model, high resolution population data, and crop yield data to evaluate the effects on human health and crop yield in China's Mainland. Our results showed that outdoor PM2.5 pollution was responsible for 1.70-1.99 million cases of all-cause mortality in 2006. The economic costs of these health effects were estimated to be 151.1-176.9 billion USD, of which 90% were attributed to mortality. The estimated crop yield losses for wheat, rice, maize, and soybean were approximately 9, 4.6, 0.44, and 0.34 million tons, respectively, resulting in economic losses of 3.4 billion USD. The total economic losses due to ambient air pollution were estimated to be 154.5-180.3 billion USD, accounting for approximately 5.7%-6.6% of the total GDP of China in 2006. Our results show that both population health and staple crop yields in China have been significantly affected by exposure to air pollution. Measures should be taken to reduce emissions, improve air quality, and mitigate the economic loss.

Several basic problems in plastic theory of geomaterials

Based on the basic mechanical properties of geomaterials,it was proven that the Drucker Postulate and the classical theory of plasticity can not be applied to geomaterials.Moreover,several basic problems of plastic theory of geomaterials were discussed.Based on the strict theoretical analysis,the following have been proven:the single yield surface model based on the classical theory of plasticity is unsuitable for geomaterials whether the rule of associated flow is applied or not;the yield surface of geomaterials is not unique,and its number is the same as the freedoms of plastic strain increment;the yield surface is not convex;and the rule of associated flow is unsuitable for geomaterials.