The homogeneously dispersed, less agglomerated (Nd0.01Y0.99)3Al5O12 nano-sized powders were synthesized by the low temperature combustion (LCS), using Nd2O3, Y2O3, Al(NO3)3·9H2O, ammonia water and citric acid as ...The homogeneously dispersed, less agglomerated (Nd0.01Y0.99)3Al5O12 nano-sized powders were synthesized by the low temperature combustion (LCS), using Nd2O3, Y2O3, Al(NO3)3·9H2O, ammonia water and citric acid as starting materials. This method effectively solves the problems caused by solid-state reaction at high temperature and hard agglomerates brought by the chemical precipitation method. The powders were characterized by TG-DTA, XRD, FT-IR, TEM respectively and the photoluminescence (PL) spectra of (Nd0.01Y0.99)3Al5O12 green and sintered ceramic disks were measured. The results show that the forming temperature of YAG crystal phase is 850 ℃ and YAP crystal phase appearing during the calcinations transforms to pure YAG at 1050 ℃. The particle size of the powders synthesized by the LCS is in a range of 20～50 nm depending on the thermal treatment temperatures. The effectively induced cross section (σin) with the value 4.03×10-19 cm2 of (Nd0.01Y0.99)3Al5O12 ceramics is about 44% higher than that of single crystal.展开更多
Nd ： YAG precursor powders were synthesized by homogeneous precipitation, and Nd ： YAG transparent ceramics were prepared by vacuum sintering at 1700 ℃ for 5 h. The ceramic materials were characterized by light tra...Nd ： YAG precursor powders were synthesized by homogeneous precipitation, and Nd ： YAG transparent ceramics were prepared by vacuum sintering at 1700 ℃ for 5 h. The ceramic materials were characterized by light transmittance and field emission gun-environment scanning microscope. Using statistics and stereology theory, study was carried out on the quantitative relationships between light transmittance and stereological parameters in three-dimensional Euclidean space. It is found that the transmittance of Nd：YAG with 1 mm in thickness is about 45% and 58% in visible and near-infrared wavelength, respectively. The transmittance linearly increases with increasing equivalent sphere diameter and reaches the theoretical value of single crystal when the equivalent sphere diameter is 20μm. The transmittance decreases with the increasing of mean specific area per unit volume of grain and discrete grains, and the transmittance decreases with increasing mean free distance of grains in Nd：YAG ceramics.展开更多
目的:比较使用不同模式Er:YAG激光以及传统车针去龋后牙本质与复合树脂的粘接强度。方法:选用人类离体磨牙模拟龋坏,分别采用Er:YAG激光中短脉冲(medium short pulse,MSP)模式、Er:YAG激光超短脉冲(super short pulse,SSP)模式和传统车...目的:比较使用不同模式Er:YAG激光以及传统车针去龋后牙本质与复合树脂的粘接强度。方法:选用人类离体磨牙模拟龋坏,分别采用Er:YAG激光中短脉冲(medium short pulse,MSP)模式、Er:YAG激光超短脉冲(super short pulse,SSP)模式和传统车针去除模拟的龋坏后,采用自酸蚀粘接剂将牙体标本与复合树脂粘接制成试件。使用万能试验机对试件进行拉伸试验,测得断裂负荷和粘接强度,并采用单因素方差分析和Tukey多重比较进行统计学分析。采用扫描电子显微镜观察3种不同去龋方式处理后的牙本质表面形态,以及涂布自酸蚀粘接剂并固化后试件的横截面形态。结果:使用Er:YAG激光MSP模式处理后牙本质与复合树脂的粘接强度最高,SSP模式处理后次之,传统车针处理后最低,但差异无统计学意义(P>0.05)。扫描电子显微镜图像显示,Er:YAG激光MSP模式处理后的牙本质表面较平坦,牙本质小管内几乎没有残屑;Er:YAG激光SSP模式处理后的牙本质表面呈现鳞片状,牙本质小管内可见少量碎屑;而传统车针处理后牙本质小管大部分处于被表面牙本质部分甚至完全遮盖的状态,牙本质小管内充满残屑。结论:使用Er:YAG激光去龋相比传统车针去龋可以获得较好的牙本质粘接强度,且对牙本质小管的处理深度和洁净度明显优于传统车针去龋,其中MSP模式更佳。展开更多
substitutes tion, high loosely dis Neodymium doped-yttrium aluminum garnet （Nd ： YAG） transparent polycrystalline ceramics already become of single crystals because they are provided with easy fabrication, low cost...substitutes tion, high loosely dis Neodymium doped-yttrium aluminum garnet （Nd ： YAG） transparent polycrystalline ceramics already become of single crystals because they are provided with easy fabrication, low cost, large size, highly doped concentraheat conductivity, mass fabrication, multi-layers and multi-filnctions. The Nd：YAG precursor powders with persed , slightly agglomerated, super fine and YAG cubic crystal phase were synthesized at 1100 ℃ by the homogeneous precipitation method, using Nd2O3, Y2O3, Al（NO3）3·9H2O and urea as raw materials, （NH4）2SO4 as electrical stabilizer, TEOS as sintering additive. The Nd：YAG transparent ceramics were prepared after being vacuum sintered at 1700 ℃ for 5 h. The Nd：YAG ceramic materials were characterized by the TG-DTA, XRD, FT-IR, TEM, FEG-ESEM and FT-PL. The results show that the crystallization temperature of YAG is 850 ℃ and the intermediate crystal phase YAP forming during the heat treatment transforms to YAG cubic crystal phase at 1050 ℃. The lasing wavelength of （Nd0.01 Y0.99）3Al5O12 transparent ceramics is 1.065 μm and there exists a slight red-shift compared to the single crystal with the same chemical composition. The optical transmittance is 45 % in the visible light and 58 % in the near infrared light and the optical transmittance descends with the decreasing the wavelength.展开更多
The homogeneously dispersed, less agglomerated YAG nanopowders are synthesized by the citrate-gel method followed by low-temperature self-propagating combustion reaction, using Y2O3, Al(NO3)3?9H2O and citric acid as s...The homogeneously dispersed, less agglomerated YAG nanopowders are synthesized by the citrate-gel method followed by low-temperature self-propagating combustion reaction, using Y2O3, Al(NO3)3?9H2O and citric acid as starting materials. This method effectively solves the problems caused by solid-state reaction at high temperature and the hard ag-glomerates brought by the chemical precipitation method. The powders are characterized by TG-DTA, XRD, FT-IR and TEM respectively. The experiments show that the forming temperature of YAG crystal phase is 850°C and the pseudo-YAG crystalline appears during the calcination and transforms to pure YAG at 1050°C. The powders with sizes less than 50 nm are observed by TEM micrography, which is consistent with the result calculated by Scherrer's formula. The powders consist of single grains.展开更多
Using nitrate precursors, a novel spray-drying assisted citrate gel process for the preparation of neodymium-doped yttrium alumi- num garnet （YAG） phase was developed. Synthesis of single-phase polycrystalline YAG w...Using nitrate precursors, a novel spray-drying assisted citrate gel process for the preparation of neodymium-doped yttrium alumi- num garnet （YAG） phase was developed. Synthesis of single-phase polycrystalline YAG was achieved at temperatures as low as 800 ℃ using the spray-drying methodology whilst conventional approaches currently available require 1000 ℃. Initially, a solution was prepared by mixing aluminum and yttrium nitrates, citric acid, etilenglycol and neodymium oxide. This solution was dried by pulverization （spray dryer） to obtain aggregated precursor powders of the compound. These aggregates were calcined at 800, 850 and 900 ℃ to determine the phase evolution from amorphous to crystalline by X-ray diffraction （XRD）. The morphology of aggregates was characterized by scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. Moreover, through XRD it was determined that the crystallization of YAG phase started at about 800 ℃ without any intermediate phases. The powders were composed of spherical aggregates with an average diameter of 1 um. From these powders, ceramic fibers with additions of 2at.% and 5at.% Nd, were extracted from the melt with diameters ranging from 30 um to 50 um.展开更多
Tetraethylenepentamine(C8H23N5,TEPA) has been used as a novel precipitant to synthesize yttrium aluminum garnet(Y3Al5O12,YAG) precursor from a mixed solution of aluminum and yttrium nitrates via a normal-strike co-pre...Tetraethylenepentamine(C8H23N5,TEPA) has been used as a novel precipitant to synthesize yttrium aluminum garnet(Y3Al5O12,YAG) precursor from a mixed solution of aluminum and yttrium nitrates via a normal-strike co-precipitation method without controlling the pH value during precipitation process.The original precursor was analyzed by thermogravimetry/differential scanning calorimetry(TG/DSC).The evolution of phase composition and micro-structure of the as-synthesized YAG powders were characterized by X-ray ...展开更多
BACKGROUND Generally,hemangiomas do not require surgical intervention;however,cases of large hemangiomas,potentially involving the throat and trachea,necessitate surgical therapy.Here,we present a case of hypopharynge...BACKGROUND Generally,hemangiomas do not require surgical intervention;however,cases of large hemangiomas,potentially involving the throat and trachea,necessitate surgical therapy.Here,we present a case of hypopharyngeal hemangioma in an adult that was successfully treated with neodymium-doped yttrium aluminum garnet(Nd-YAG)laser.CASE SUMMARY Laryngoscopic examination of a 61-year-old man demonstrated the presence of a large,submucosal vascular lesion that extended into the epiglottis,left arytenoid cartilage,lateral to the aryepiglottic fold,and pyriform sinus.The lesion was resected and photocoagulated with limited hemorrhage using Nd:YAG laser.The hypopharyngeal hemangioma was completely excised.The patient showed no recurrence of hypopharyngeal hemangioma during the 1.5-year follow-up period.CONCLUSION Laser therapy is one of the effective tools for treating hemangiomas with rapid,uncontrolled growth or in functional areas,with few side effects and complications.The present case of a male patient with a large hypopharyngeal hemangioma,treated with YAG laser,demonstrates the efficacy of laser photocoagulation in treating cases of hemangiomas,without the risk of bleeding or airway obstruction.The favorable postoperative outcomes demonstrated by our patient with Nd:YAG laser therapy indicate its consideration in the therapy of similar cases.展开更多
Transparent polycrystaUine neodymiumdoped yttrium aluminum garnet ceramics （Nd：YAG） with better chemical stability, excellent optical and high temperature mechanical property is becoming a new laser host material. ...Transparent polycrystaUine neodymiumdoped yttrium aluminum garnet ceramics （Nd：YAG） with better chemical stability, excellent optical and high temperature mechanical property is becoming a new laser host material. The Nd：YAG precursor powders with loosely dispersed, slightly agglomerated and YAG cubic crystal phase were synthesized at 1100 ℃ by the co-precipitation method combined with the reverse strike,展开更多
In this study,a single-doped phosphors yttrium aluminum garnet(Y_(3)Al_(5)O_(12),YAG):Ce^(3+),single-doped YAG:Sc^(3+),and double-doped phosphors YAG:Ce^(3+),Sc^(3+) were prepared by spark plasma sintering(SPS)(lower ...In this study,a single-doped phosphors yttrium aluminum garnet(Y_(3)Al_(5)O_(12),YAG):Ce^(3+),single-doped YAG:Sc^(3+),and double-doped phosphors YAG:Ce^(3+),Sc^(3+) were prepared by spark plasma sintering(SPS)(lower than 1 200℃).The characteristics of synthesized phosphors were determined using scanning electron microscopy(SEM),X-ray diffraction(XRD),and fluorescence spectroscopy.During SPS,the lattice structure of YAG was maintained by the added Ce^(3+) and Sc^(3+).The emission wavelength of YAG:Ce^(3+) prepared from SPS(425-700 nm) was wider compared to that of YAG:Ce^(3+) prepared from high-temperature solid-state reaction(HSSR)(500-700 nm).The incorporation of low-dose Sc^(3+) in YAG:Ce^(3+) moved the emission peak towards the short wavelength.展开更多
Nd∶YAG precursor powders were synthesized by homogeneous precipitation and Nd∶YAG transparent ceramics were prepared by vacuum sintering at 1700 ℃ for 5 h. The ceramic materials were characterized by light transmit...Nd∶YAG precursor powders were synthesized by homogeneous precipitation and Nd∶YAG transparent ceramics were prepared by vacuum sintering at 1700 ℃ for 5 h. The ceramic materials were characterized by light transmittance, field emission gun-environment scanning microscope. Fractal geometry was used to study the quantitative relationships between light transmittance and fractal dimensions of Nd∶YAG transparent ceramics. It was found that the transmittance of Nd∶YAG with 1 mm in thickness was about 45% and 58% in visible and near-infrared region respectively. The microstructures of Nd∶YAG transparent ceramics were obvious fractal characteristic and fractal dimensions depart a little from two-dimension. The light transmittance decreased with increasing of fractal dimension and nonlinear fit curve was y=1350-1185x+269x2 between fractal dimension and light transmittance of Nd∶YAG transparent ceramics.展开更多
Phosphor yttrium aluminum garnet Y3A15O12 （YAG）, activated with trivalent cerium （Ce^3＋）, was synthesized by T-tube impinging streams, T-type vortex impinging streams co-precipitation method （IS-CP） and direct ...Phosphor yttrium aluminum garnet Y3A15O12 （YAG）, activated with trivalent cerium （Ce^3＋）, was synthesized by T-tube impinging streams, T-type vortex impinging streams co-precipitation method （IS-CP） and direct co-precipitation method （D-CP）, respectively. The crystallization, morphologies, particle size and particle size distribution of the phosphors obtained under different experimental conditions were studied. The influence of various factors on the luminescence intensity of the phosphor was also investigated, such as feeding methods, volume flow rate, contents of Ce and initial reactant concentration. The results show that the precursors synthesized by T-tube impinging streams co-precipitation reaction transform to Y3A15O12 （YAG） phosphor at about 1 000 ℃. The particles are far smaller and narrower than those prepared by D-CP. In the impinging streams co-precipitation system, the luminescent intensity of YAG：Ce phosphor increases with the increase of liquid flow rate. The intensity firstly increases then decreases with the increasing Ce^3＋ doping content, and the maximum intensity is shown at 1.67% （molar fraction） Ce. Luminescent intensity gradually decreases with the increase of initial concentration of reactants. At the same operational condition, the luminescent intensity of the phosphors prepared by T-tube impinging streams reactor is higher than that by D-CP, and the luminescent intensity of the phosphors prepared by T-type vortex impinging streams is higher than that by T-tube impinging streams reactor.展开更多
BACKGROUND The goal of periodontal disease treatment is to completely remove bacteria and promote wound healing.The erbium-doped yttrium aluminum garnet(Er:YAG)laser is commonly used to treat periodontal disease.Advan...BACKGROUND The goal of periodontal disease treatment is to completely remove bacteria and promote wound healing.The erbium-doped yttrium aluminum garnet(Er:YAG)laser is commonly used to treat periodontal disease.Advanced platelet-rich fibrin+(A-PRF+)secrets growth factors that accelerates soft-and hard-tissue regeneration and wound healing.Herein I present 2 cases of patients with oral diseases treated with a combination of Er:YAG laser and A-PRF+.CASE SUMMARY Case 1 was a female with pocket depth bone loss over 8 mm and infection of tooth 31 and 41,and severe advanced periodontitis with grade III mobility.Case 2 was a male with tooth 22 root end apical swelling and infection and alveolar bony defects.Clinical outcomes were recorded at 6 and 36 mo.In case 1,the Er:YAG laser was used to perform open flap debridement(100 mJ/pulse,15 Hz)and remove calculus and granulation tissue(50 mJ/pulse,30 Hz).In case 2 the laser was used to create a semilunar full thickness flap incision(80 mJ/pulse,20 Hz)and eliminate the pathogen(100 mJ/pulse,15 Hz).In both patients,A-PRF+mixed with bone was used to fill bone defects,and A-PRF+autologous membranes were used to cover tension-free primary flaps.There was no recurrent infection at 36 mo,and tissue regeneration and would healing occurred.CONCLUSION Debridement with an Er:YAG laser followed by treatment with A-PRF+is effective for the treatment periodontal diseases with bone defects.展开更多
文摘The homogeneously dispersed, less agglomerated (Nd0.01Y0.99)3Al5O12 nano-sized powders were synthesized by the low temperature combustion (LCS), using Nd2O3, Y2O3, Al(NO3)3·9H2O, ammonia water and citric acid as starting materials. This method effectively solves the problems caused by solid-state reaction at high temperature and hard agglomerates brought by the chemical precipitation method. The powders were characterized by TG-DTA, XRD, FT-IR, TEM respectively and the photoluminescence (PL) spectra of (Nd0.01Y0.99)3Al5O12 green and sintered ceramic disks were measured. The results show that the forming temperature of YAG crystal phase is 850 ℃ and YAP crystal phase appearing during the calcinations transforms to pure YAG at 1050 ℃. The particle size of the powders synthesized by the LCS is in a range of 20～50 nm depending on the thermal treatment temperatures. The effectively induced cross section (σin) with the value 4.03×10-19 cm2 of (Nd0.01Y0.99)3Al5O12 ceramics is about 44% higher than that of single crystal.
基金Project supported by Key Science and Technology of Chinese Ministry of Education (205037)
文摘Nd ： YAG precursor powders were synthesized by homogeneous precipitation, and Nd ： YAG transparent ceramics were prepared by vacuum sintering at 1700 ℃ for 5 h. The ceramic materials were characterized by light transmittance and field emission gun-environment scanning microscope. Using statistics and stereology theory, study was carried out on the quantitative relationships between light transmittance and stereological parameters in three-dimensional Euclidean space. It is found that the transmittance of Nd：YAG with 1 mm in thickness is about 45% and 58% in visible and near-infrared wavelength, respectively. The transmittance linearly increases with increasing equivalent sphere diameter and reaches the theoretical value of single crystal when the equivalent sphere diameter is 20μm. The transmittance decreases with the increasing of mean specific area per unit volume of grain and discrete grains, and the transmittance decreases with increasing mean free distance of grains in Nd：YAG ceramics.
文摘目的:比较使用不同模式Er:YAG激光以及传统车针去龋后牙本质与复合树脂的粘接强度。方法:选用人类离体磨牙模拟龋坏,分别采用Er:YAG激光中短脉冲(medium short pulse,MSP)模式、Er:YAG激光超短脉冲(super short pulse,SSP)模式和传统车针去除模拟的龋坏后,采用自酸蚀粘接剂将牙体标本与复合树脂粘接制成试件。使用万能试验机对试件进行拉伸试验,测得断裂负荷和粘接强度,并采用单因素方差分析和Tukey多重比较进行统计学分析。采用扫描电子显微镜观察3种不同去龋方式处理后的牙本质表面形态,以及涂布自酸蚀粘接剂并固化后试件的横截面形态。结果:使用Er:YAG激光MSP模式处理后牙本质与复合树脂的粘接强度最高,SSP模式处理后次之,传统车针处理后最低,但差异无统计学意义(P>0.05)。扫描电子显微镜图像显示,Er:YAG激光MSP模式处理后的牙本质表面较平坦,牙本质小管内几乎没有残屑;Er:YAG激光SSP模式处理后的牙本质表面呈现鳞片状,牙本质小管内可见少量碎屑;而传统车针处理后牙本质小管大部分处于被表面牙本质部分甚至完全遮盖的状态,牙本质小管内充满残屑。结论:使用Er:YAG激光去龋相比传统车针去龋可以获得较好的牙本质粘接强度,且对牙本质小管的处理深度和洁净度明显优于传统车针去龋,其中MSP模式更佳。
文摘substitutes tion, high loosely dis Neodymium doped-yttrium aluminum garnet （Nd ： YAG） transparent polycrystalline ceramics already become of single crystals because they are provided with easy fabrication, low cost, large size, highly doped concentraheat conductivity, mass fabrication, multi-layers and multi-filnctions. The Nd：YAG precursor powders with persed , slightly agglomerated, super fine and YAG cubic crystal phase were synthesized at 1100 ℃ by the homogeneous precipitation method, using Nd2O3, Y2O3, Al（NO3）3·9H2O and urea as raw materials, （NH4）2SO4 as electrical stabilizer, TEOS as sintering additive. The Nd：YAG transparent ceramics were prepared after being vacuum sintered at 1700 ℃ for 5 h. The Nd：YAG ceramic materials were characterized by the TG-DTA, XRD, FT-IR, TEM, FEG-ESEM and FT-PL. The results show that the crystallization temperature of YAG is 850 ℃ and the intermediate crystal phase YAP forming during the heat treatment transforms to YAG cubic crystal phase at 1050 ℃. The lasing wavelength of （Nd0.01 Y0.99）3Al5O12 transparent ceramics is 1.065 μm and there exists a slight red-shift compared to the single crystal with the same chemical composition. The optical transmittance is 45 % in the visible light and 58 % in the near infrared light and the optical transmittance descends with the decreasing the wavelength.
基金This work is financially supported by the Excellent Teachers Fund by the Ministry of Education of China (No. KB200226).
文摘The homogeneously dispersed, less agglomerated YAG nanopowders are synthesized by the citrate-gel method followed by low-temperature self-propagating combustion reaction, using Y2O3, Al(NO3)3?9H2O and citric acid as starting materials. This method effectively solves the problems caused by solid-state reaction at high temperature and the hard ag-glomerates brought by the chemical precipitation method. The powders are characterized by TG-DTA, XRD, FT-IR and TEM respectively. The experiments show that the forming temperature of YAG crystal phase is 850°C and the pseudo-YAG crystalline appears during the calcination and transforms to pure YAG at 1050°C. The powders with sizes less than 50 nm are observed by TEM micrography, which is consistent with the result calculated by Scherrer's formula. The powders consist of single grains.
基金Universidad Michoacana de San Nicolás de Hidalgo (UMSNH) (1.24.-2005-2007)
文摘Using nitrate precursors, a novel spray-drying assisted citrate gel process for the preparation of neodymium-doped yttrium alumi- num garnet （YAG） phase was developed. Synthesis of single-phase polycrystalline YAG was achieved at temperatures as low as 800 ℃ using the spray-drying methodology whilst conventional approaches currently available require 1000 ℃. Initially, a solution was prepared by mixing aluminum and yttrium nitrates, citric acid, etilenglycol and neodymium oxide. This solution was dried by pulverization （spray dryer） to obtain aggregated precursor powders of the compound. These aggregates were calcined at 800, 850 and 900 ℃ to determine the phase evolution from amorphous to crystalline by X-ray diffraction （XRD）. The morphology of aggregates was characterized by scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. Moreover, through XRD it was determined that the crystallization of YAG phase started at about 800 ℃ without any intermediate phases. The powders were composed of spherical aggregates with an average diameter of 1 um. From these powders, ceramic fibers with additions of 2at.% and 5at.% Nd, were extracted from the melt with diameters ranging from 30 um to 50 um.
文摘Tetraethylenepentamine(C8H23N5,TEPA) has been used as a novel precipitant to synthesize yttrium aluminum garnet(Y3Al5O12,YAG) precursor from a mixed solution of aluminum and yttrium nitrates via a normal-strike co-precipitation method without controlling the pH value during precipitation process.The original precursor was analyzed by thermogravimetry/differential scanning calorimetry(TG/DSC).The evolution of phase composition and micro-structure of the as-synthesized YAG powders were characterized by X-ray ...
基金Supported by the Jinshan Hospital Qihang Plan,No.2018-JSYYQH-02
文摘BACKGROUND Generally,hemangiomas do not require surgical intervention;however,cases of large hemangiomas,potentially involving the throat and trachea,necessitate surgical therapy.Here,we present a case of hypopharyngeal hemangioma in an adult that was successfully treated with neodymium-doped yttrium aluminum garnet(Nd-YAG)laser.CASE SUMMARY Laryngoscopic examination of a 61-year-old man demonstrated the presence of a large,submucosal vascular lesion that extended into the epiglottis,left arytenoid cartilage,lateral to the aryepiglottic fold,and pyriform sinus.The lesion was resected and photocoagulated with limited hemorrhage using Nd:YAG laser.The hypopharyngeal hemangioma was completely excised.The patient showed no recurrence of hypopharyngeal hemangioma during the 1.5-year follow-up period.CONCLUSION Laser therapy is one of the effective tools for treating hemangiomas with rapid,uncontrolled growth or in functional areas,with few side effects and complications.The present case of a male patient with a large hypopharyngeal hemangioma,treated with YAG laser,demonstrates the efficacy of laser photocoagulation in treating cases of hemangiomas,without the risk of bleeding or airway obstruction.The favorable postoperative outcomes demonstrated by our patient with Nd:YAG laser therapy indicate its consideration in the therapy of similar cases.
文摘Transparent polycrystaUine neodymiumdoped yttrium aluminum garnet ceramics （Nd：YAG） with better chemical stability, excellent optical and high temperature mechanical property is becoming a new laser host material. The Nd：YAG precursor powders with loosely dispersed, slightly agglomerated and YAG cubic crystal phase were synthesized at 1100 ℃ by the co-precipitation method combined with the reverse strike,
基金Funded by the Primary Research and Development Plan of Jiangsu Province(No.BE2016175)。
文摘In this study,a single-doped phosphors yttrium aluminum garnet(Y_(3)Al_(5)O_(12),YAG):Ce^(3+),single-doped YAG:Sc^(3+),and double-doped phosphors YAG:Ce^(3+),Sc^(3+) were prepared by spark plasma sintering(SPS)(lower than 1 200℃).The characteristics of synthesized phosphors were determined using scanning electron microscopy(SEM),X-ray diffraction(XRD),and fluorescence spectroscopy.During SPS,the lattice structure of YAG was maintained by the added Ce^(3+) and Sc^(3+).The emission wavelength of YAG:Ce^(3+) prepared from SPS(425-700 nm) was wider compared to that of YAG:Ce^(3+) prepared from high-temperature solid-state reaction(HSSR)(500-700 nm).The incorporation of low-dose Sc^(3+) in YAG:Ce^(3+) moved the emission peak towards the short wavelength.
基金Study on Optical Properties and Structure of Transparent Ceramics,Chinese Education Ministry Excellent Teachers Project (KB200226)
文摘Nd∶YAG precursor powders were synthesized by homogeneous precipitation and Nd∶YAG transparent ceramics were prepared by vacuum sintering at 1700 ℃ for 5 h. The ceramic materials were characterized by light transmittance, field emission gun-environment scanning microscope. Fractal geometry was used to study the quantitative relationships between light transmittance and fractal dimensions of Nd∶YAG transparent ceramics. It was found that the transmittance of Nd∶YAG with 1 mm in thickness was about 45% and 58% in visible and near-infrared region respectively. The microstructures of Nd∶YAG transparent ceramics were obvious fractal characteristic and fractal dimensions depart a little from two-dimension. The light transmittance decreased with increasing of fractal dimension and nonlinear fit curve was y=1350-1185x+269x2 between fractal dimension and light transmittance of Nd∶YAG transparent ceramics.
基金Project(200805330032)supported by the Natural Educative Doctoral Foundation of ChinaProjects(20080440987,200902475)supported by the China Postdoctoral Science Foundation
文摘Phosphor yttrium aluminum garnet Y3A15O12 （YAG）, activated with trivalent cerium （Ce^3＋）, was synthesized by T-tube impinging streams, T-type vortex impinging streams co-precipitation method （IS-CP） and direct co-precipitation method （D-CP）, respectively. The crystallization, morphologies, particle size and particle size distribution of the phosphors obtained under different experimental conditions were studied. The influence of various factors on the luminescence intensity of the phosphor was also investigated, such as feeding methods, volume flow rate, contents of Ce and initial reactant concentration. The results show that the precursors synthesized by T-tube impinging streams co-precipitation reaction transform to Y3A15O12 （YAG） phosphor at about 1 000 ℃. The particles are far smaller and narrower than those prepared by D-CP. In the impinging streams co-precipitation system, the luminescent intensity of YAG：Ce phosphor increases with the increase of liquid flow rate. The intensity firstly increases then decreases with the increasing Ce^3＋ doping content, and the maximum intensity is shown at 1.67% （molar fraction） Ce. Luminescent intensity gradually decreases with the increase of initial concentration of reactants. At the same operational condition, the luminescent intensity of the phosphors prepared by T-tube impinging streams reactor is higher than that by D-CP, and the luminescent intensity of the phosphors prepared by T-type vortex impinging streams is higher than that by T-tube impinging streams reactor.
文摘BACKGROUND The goal of periodontal disease treatment is to completely remove bacteria and promote wound healing.The erbium-doped yttrium aluminum garnet(Er:YAG)laser is commonly used to treat periodontal disease.Advanced platelet-rich fibrin+(A-PRF+)secrets growth factors that accelerates soft-and hard-tissue regeneration and wound healing.Herein I present 2 cases of patients with oral diseases treated with a combination of Er:YAG laser and A-PRF+.CASE SUMMARY Case 1 was a female with pocket depth bone loss over 8 mm and infection of tooth 31 and 41,and severe advanced periodontitis with grade III mobility.Case 2 was a male with tooth 22 root end apical swelling and infection and alveolar bony defects.Clinical outcomes were recorded at 6 and 36 mo.In case 1,the Er:YAG laser was used to perform open flap debridement(100 mJ/pulse,15 Hz)and remove calculus and granulation tissue(50 mJ/pulse,30 Hz).In case 2 the laser was used to create a semilunar full thickness flap incision(80 mJ/pulse,20 Hz)and eliminate the pathogen(100 mJ/pulse,15 Hz).In both patients,A-PRF+mixed with bone was used to fill bone defects,and A-PRF+autologous membranes were used to cover tension-free primary flaps.There was no recurrent infection at 36 mo,and tissue regeneration and would healing occurred.CONCLUSION Debridement with an Er:YAG laser followed by treatment with A-PRF+is effective for the treatment periodontal diseases with bone defects.
