ZERO-CURRENT AND ZERO-VOLTAGE SWITCHING PWM BOOST FULL-BRIDGE CON VERTER

This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load range using the energy of the output capacitor. Ma king use of parasitic capacitors of the lagging switches and parallel auxiliary i nductance with the primary winding of the transformer, the lagging switches can realize zero voltage switching (ZVS) under any load. Compared with the ZCS PWM Boost FB converter, the new converter has no current duty cycle loss. Operat ional principle and parameter design are analyzed. Experimental results verify the effectiveness of the proposed converter.

Faster vortex core switching with lower current density using three-nanocontact spin-polarized currents in a confined structure

We perform micromagnetic simulations on the switching of magnetic vortex core by using spin-polarized currents through a three-nanocontact geometry. Our simulation results show that the current combination with an appropriate current flow direction destroys the symmetry of the total effective energy of the system so that the vortex core can be easier to excite,resulting in less critical current density and a faster switching process. Besides its fundamental significance, our findings provide an additional route to incorporating magnetic vortex phenomena into data storage devices.

Dependence of Switching Current Distribution of a Current-Biased Josephson Junction on Microwave Frequency

We investigate the distribution of the switching current of a current-biased Josephson junction （CBJJ） and its dependence on the microwave frequency using two theoretical methods, one of which is the quantum trajectory method and the other is the master equation method. Both the methods show that the distribution of the switching current of CBJJ will exhibit double peaks in a certain range of microwave frequency if proper microwave power is given, and the gap between the two peaks will increase with the microwave frequency. The obtained results can be used to identify the energy difference of the ground and first excited states in a Josephson junction for any bias current.

Transitional Recovery Voltages at Capacitive Currents Switching-off by Vacuum and SF6 Circuit-Breakers

Results of calculation the recovery voltages conditioned by capacitive currents switching-off by high voltage vacuum and auto-compression （SF6） circuit-breakers are presented in the article. The purpose of research was evaluating the maximum values of recovery voltages and also studying the dependence of recovery voltages on some influencing factors, especially on type of circuit-breaker presented in numerical models with its dielectric strength restoration law, chopping current and operation time. The research was carried out with using computer simulation.

Constant Ripple Current Control for Switching DC-DC Converter

The adapted DC-DC converters should be smaller in size and have a small output current ripple to meet the increasing demand for low voltages with high performance and high density micro processors for several microelectronic load applications. This paper proposes a DC-DC converter using variable on-time and variable switching frequency control enhanced constant ripple current control and reduced magnetic components. The proposed converter is realized by making the turn-offtime proportional to the on-time of the converter, according to the input and output voltage, thereby reducing the corresponding current ripple on output voltage in the continuous conduction mode. A Buck DC-DC converter using the proposed control strategy is analyzed in detail, along with some experimental results to show the performance and effectiveness of this converter.

A NEW SOFT-SWITCHING PUSH-PULL THREE-LEVEL CONVERTER

The application areas of conventional push pull converters are limited because of high voltage stress of switches (twice of input voltage). This paper presents a novel zero voltage and zero current switching (ZCS) PWM push pull three level converter in which the voltage stress of switches is input voltage. With phase shifted modulation strategy, the leading switches can only realize zero voltage switching (ZVS), and the lagging switches can realize ZCS when block capacitor and block diodes are added. Using the strategy, the converter overcomes the drawbacks presented by the conventional push pull converter, such as magnetic aberration, large switch loss, and voltage spike on switches, so it can get higher efficiency, and a wider application area. The operating principle of the new converter is analyzed and verified on a 600 W, 50 kHz experimental prototype. Several zero voltage and zero current switching PWM push pull three level converters are proposed.

Nonlinear Auto-Companding Method for Behavioral Modeling of Switched-Current Circuits

A wavelet collocation method with nonlinear auto companding is proposed for behavioral modeling of switched current circuits.The companding function is automatically constructed according to the initial error distribution obtained through approximating the input output function of the SI circuit by conventional wavelet collocation method.In practical applications,the proposed method is a general purpose approach,by which both the small signal effect and the large signal effect are modeled in a unified formulation to ease the process of modeling and simulation.Compared with the published modeling approaches,the proposed nonlinear auto companding method works more efficiently not only in controlling the error distribution but also in reducing the modeling errors.To demonstrate the promising features of the proposed method,several SI circuits are employed as examples to be modeled and simulated.

Resistive switching characteristics of Ti/ZrO_2/Pt RRAM device

In this paper, the bipolar resistive switching characteristic is reported in Ti/ZrO2/Pt resistive switching memory de- vices. The dominant mechanism of resistive switching is the formation and rupture of the conductive filament composed of oxygen vacancies. The conduction mechanisms for low and high resistance states are dominated by the ohmic conduc- tion and the trap-controlled space charge limited current （SCLC） mechanism, respectively. The effect of a set compliance current on the switching parameters is also studied： the low resistance and reset current are linearly dependent on the set compliance current in the log-log scale coordinate; and the set and reset voltage increase slightly with the increase of the set compliance current. A series circuit model is proposed to explain the effect of the set compliance current on the resistive switching behaviors.

A novel superjunction MOSFET with improved ruggedness under unclamped inductive switching

The ruggedness of a superjunction metal-oxide semiconductor field-effect transistor （MOSFET） under unclamped inductive switching conditions is improved by optimizing the avalanche current path. Inserting a P-island with relatively high doping concentration into the P-column, the avalanche breakdown point is localized. In addition, a trench type P＋ contact is designed to shorten the current path. As a consequence, the avalanche current path is located away from the N＋ source/P-body junction and the activation of the parasitic transistor can be effectively avoided. To verify the proposed structural mechanism, a two-dimensional （2D） numerical simulation is performed to describe its static and on-state avalanche behaviours, and a method of mixed-mode device and circuit simulation is used to predict its performances under realistic unclanlped inductive switching. Simulation shows that the proposed structure can endure a remarkably higher avalanche energy compared with a conventional superjunction MOSFET.

A Novel Crowbar Impulse Current Circuit for Testing the Switch-Type SPD

A crowbar impulse current circuit for testing the switch-type surge protective device （SPD） is presented. The crowbar circuit consists of a computer control circuit, a trigger voltage pulse generator, a main discharging switch, and a crowbar pseudospark switch. The active trigger technology was studied in the crowbar impulse current circuit. The circuit monitors the main discharging current and generates a trigger signal at a proper time for the crowbar pseudospark switch operation. The trigger characteristics of the main discharge switch and the crowbar pseu- dospark switch were investigated. By monitoring the preset applied capacitor voltage, the gap distance of the main discharging switch could be adjusted to ensure a discharging delay time less than 2 μs. Equipped with a surface ttashover trigger device made of high relative perimittivity dielectric material BaTiO3 （εr = 3460）, the discharge delay time of the crowbar pseudospark switch is less than 85 ns, and the minimum operating voltage is less than 1% of its self-breakdown voltage. With a storage capacitor of 9 μF , an inductor of 18 μH and a crowbar pseudospark switch, a load of 30 mΩ and an applied capacitor voltage of 40 kV, an impulse current waveform of maximum 25 kA was generated with a rise time and time to half peak value of 17.2 μs and 336μs respectively.

A New Switching Sequences of SVPWM for Six-Phase Induction Motor with Features of Reduced Switching Losses

In this paper,new SVPWM switching sequences for six-phase asymmetrical induction motor drives are derived with the aim to reduce inverter’s switching losses.Total three switching sequences are introduced in this paper.These sequences are derived such that the phases get continuously clamped when a current of the phases is around its peak magnitude and hence reduced switching losses are recorded.The comparative performances of these modulation techniques are studied with two existing switching sequences.Simulation,analytical and experimental results are presented.Based on these results,it is found that new switching sequences reduce switching losses effectively in dual three phase inverters.

Study of the Fast-Closing Switch Used for Fault Current Limiters in Power System

This paper presents a new type of fault current limiter (FCL) based on fast closing switch, which is composed of a capacitor bank and a reactor in series. The main control component is a fast closing switch connected in parallel with the capacitors, which is driven by the electromagnetic repulsion force. It can response the order within 1 ms. When fault occurs, the switch closes and the capacitors are bypassed, and the fault current is limited by the reactor. Simulation analysis and experiment show that the electromagnetic repulsion force actuator can meet the demand of fast closing switch, it is feasible to develop the FCL with low cost and high reliability.

DESIGN OF TERNARY CURRENT-MODE CMOS CIRCUITS BASED ON SWITCH-SIGNAL THEORY

By applying switch-signal theory, the interaction between MOS transmission switch-ing transistor and current signal in current-mode CMOS circuits is analyzed, and the theory oftransmission current-switches which is suitable to current-mode CMOS circuits is proposed. Thecircuits, such as ternary full-adder etc., designed by using this theory have simpler circuit struc-tures and correct logic functions. It is confirmed that this theory is efficient in guiding the logicdesign of current-mode CMOS circuits at switch level.

High-power High-efficient and Simplified High-frequency Switching Power Supply for Electrolytic Plating

针对大功率电解电镀开关电源的输入整流级引起的无功和谐波等电能质量问题,研究了一种基于高效PWM整流的高频开关电源。该电源前级整流器仅用4个开关管来进行PWM整流,后级采用半桥逆变器进行高频变换,显著减少了开关数量。针对三相四开关PWM整流器,推导一种基于开关模型的无差拍控制方法,该方法可实现系统的快速、无差整流。针对多台开关电源的并联均流问题,提出一种基于虚拟阻抗的自均流控制方法,可实现多台电源的均流稳定运行。通过仿真与实验验证了所提结构和控制方法的正确性。

A Design of the Elliptic Switched Current Filter

In conformity with a fifth order RLC elliptic filter circuit prototype, it is easy to conceive the corresponding RC active filter circuit. Simple and feasible method presented here can be used to contrive the equivalent switched capacitor filter circuit and switched current filter circuit. Consulting the technique data manual, we can expediently design a specific RLC filter. Therefore, it is of great convenience to design the switched current filter, which has the same performances. Such a kind of technology is useful in the domain of analogue sampled data signal processing.

Reduction of current chopping noise with DSP controller in switched reluctance motor drive system

A novel current chopping mode was used in a switched reluctance motor drive system to make full use of the characteristics of digital signal processor (DSP) TMS320F240. The necessity of this 180° phase-shift current control (PSCC) mode is introduced first and then the principle of PSCC covering both hardware requirement and software programming is described in detail. The analysis made indicated that with this mode, the chopping frequency in winding can reach 20 kHz with 10 kHz power switches and the control frequency can reach 40 kHz at the same time. Subsequently, based on the linear and nonlinear mathematical models of the switched reluctance motor (SRM), some simulation work has been done. The simulation results show that when this mode is applied to SRM drive (SRD) system, the current waveform becomes better. So the ripple of the torque is reduced simultaneously and the vibration and acoustic noise are reduced involuntarily. Stationary tests show that the acoustic noise is greatly diminished. Finally, some experiments were made using a 50 kW SRD system for electric vehicle (EV). Experimental results indicate that this mode can be implemented feasibly and it has a good action on the SRD system.

Research on a Fast-Closing Switch Based Fault Current Limiter with Series Compensation

A new type of fault current limiter (FCL) with series compensation based fast-closing switch is proposed. It is composed of a capacitor bank and a reactor in series. The main control component is a fast-closing switch connected in parallel with the capacitors, which is driven by the electromagnetic repulsion force. When fault occurs, the switch closes and bypasses the capacitors, and the fault is limited by the reactor then. Simulated analysis and experiments show that it is feasible to develop the FCL with low cost and high reliability. The effectiveness of transient stability for power system is evaluated by digital simulation.

Torque Sharing Function Control of Switched Reluctance Machines with Reduced Current Sensors

This paper presents a Torque Sharing Function(TSF)control of Switched Reluctance Machines(SRMs)with different current sensor placements to reconstruct the phase currents.TSF requires precise phase current information to ensure accurate torque control.Two proposed methods with different chopping transistors or a new PWM implementation require four or two current sensors to replace the current sensors on each phase regardless of the phase number.For both approaches,the actual phase current can be easily extracted during the single phase conducting region.However,how to separate the incoming and outgoing phase current values during the commutation region is the difficult issue to deal with.In order to derive these two adjacent currents,the explanations and comparisons of two proposed methods are described.Their effectiveness is verified by experimental results on a four-phase 8/6 SRM.Finally,the approach with a new PWM implementation is selected,which requires only two current sensors for reducing the number of sensors.The control system can be more compact and cheaper.