气象观测场在汽车试验场中的应用研究

汽车试验场作为汽车开展道路测试的重要场所,用于验证汽车产品的品质以及可靠性。除了场地道路外,气象条件作为汽车道路测试的重要一环,在《GB/T12534-1990汽车道路试验方法通则》中也有明确要求,如:试验时应是无雨无雾天气,相对湿度小于95%,气温0-40℃,风速不大于3m/s。同时气象条件也作为试验场道路管控的重要依据,实时风速、雨量、能见度等信息为场地管理者发布限速、限行、封场等通知提供必要参考依据,直接影响道路测试安全管控的及时性。因此,文章从气象观测场的建设、气象服务、异常天气道路管控等方面开展气象观测场在汽车试验场中的应用研究。

Hard IP Core Nondestructive Testing Technology

Based on the analysis of the existing hard IP core testing technology, the hard IP core nondestructive testing technology was studied, according to the verification requirements of a large number of hard IP core precise and fast testing. Combined with the external automatic test equipment (ATE) and the on-chip evaluation circuit, a general evaluation system of simulating user system on chip (SOC) with signal timing calibration and compensation by software and hardware compensation structures were introduced to realize the function, performance and reliability verification of the hard IP core. The design and verification of a random access memory (SRAM) hard IP core based on an on-chip evaluation circuit was actually completed, and the key timing parameters of the hard IP core were tested. The address setup time parameter was taken as an example to analyze the specific testing method and the test results were obtained. With this testing technology, the accuracy of testing the timing parameters of hard IP core can reach pS level, compared with the hard IP core packaged test, the accuracy of the result data is fully reflected.

Monitoring of polymeric membrane fouling in hollow fiber module using ultrasonic nondestructive testing

This study describes the development of novel protocols extending the real-time ultrasonic reflectometry(UTDR) for the detection of membrane fouling in hollow fiber module during ultrafiltration(UF) of oily water treatment. A specially designed acoustic sensor with a frequency of 2.5 MHz was used. The hollow fiber membranes used were polysulphone(PSf) UF membranes with MWCO 40 kDa. The wastewaters with three different oily concentrations of 100, 500 and 1 000 mg/L were investigated. Diesel oil was utilized as the primary foulant. The results show that the permeate flux declines with operation time and its value becomes lower with the increase of the oily concentration in wastewater. It is found that ultrasonic measurement can detect the fouling and cleaning processes. A new signal analysis protocol-ultrasonic reflected energy was developed. Ultrasonic reflected energy obtained indicates the deposition of oily layer as a function of operation time and its removal after cleaning. The overall flux decline is reasonably correlated with the changes in ultrasonic reflected energy. This research provides the evidence that the ultrasonic reflectometry technique is capable of monitoring membrane fouling and cleaning in hollow fiber modules.

A Kind of Potential Practical Sensors of Metamaterial in Electromagnetic Flaw Nondestructive Testing

We present a new kind of method of electromagnetic flaw nondestructive testing with coating of metamaterials and simulation near electromagnetic field property for test crack. The simulation of improving a Nondestructive testing (NDT) probe electromagnetic radiant property by Metamatrials (MMs) covering a tiny current element is investigated and analyzed using Ansoft HFSS based on finite element method (FEM), which permittivity and permeability are negative. Electromagnetic model: Ideal MMs ball shell with inner radius of 1 mm and outer radius variation, and the shell’s relative permittivity and relative permeability are all –3.0, dielectric loss tangent and magnetic loss tangent are all 0.1;and exciting current element length is with 0.3 mm, diameter 0.2 mm, value 1 mA at frequency 10 GHz;and simulation is with radiation boundary conditions. The simulating near electromagnetic field variety with ratio of inner radius and out radius, and so near or local field of MMs sensor on a surface crack, as well as comparing near field value of sensor with coating common material are finished. Results can be seen that MMs film sensor near electromagnetic field and radiation properties are obviously better than other two kinds of structures without coating medium and coating with common medium, and Metamaterial may be opened out some new kinds of sensors in electromagnetic flaw nondestructive testing for potential practical applications in future.

温度和热驯化对胡氏大生熊虫运动行为的影响

The beneficial acclimation hypothesis (BAH) predicts that animals acclimated to a particular temperature have enhanced performance or fitness at that temperature in comparison with animals acclimated to other temperatures. The BAH has been tested by a variety of empirical examinations, and was rejected by some of them. In order to provide new evidences for the BAH, the effects of acute and acclimation temperature (AT) on locomotor performance of Macrobiotus hufelandi (Tardigrada: Macrobiotidae) were investigated. The tardigrades were collected from Nanwutai, Qinling Mountains which traverse from west to east in central China. The subjects were acclimated to either 2℃ or 22℃ for 2 weeks. The animal was transferred onto a frosted slide and allowed to walk freely at the performance temperature (PT) 2℃ or 22℃. Only one individual was tested per test bout, which lasted from three to five minutes. To avoid occurrence of thermal acclimation effect, the standard adaptation time was limited to 1.5 min. Each subject was tested for once at the same PT, and was tested only at one PT. A total of 25 individuals were tested and measured at the same PT. The locomotor performance of the animals was recorded with a digital video camera mounted on a microscope at 4×10 amplification and replayed on a PC. Every subject was identified. Walking speed (WS) and percentage of time moving (PTM) at both PTs (2℃ or 22℃) were selected as the rate parameters of locomotor performance. The two-way repeated measures ANOVA with a significance level of α= 0.05 and Duncan multiple range test were used to analyze the data. WS of the animals acclimated to and tested at the same temperatures was significantly faster than that for animals acclimated to and tested at the different temperatures, similarly, PTM of the animals acclimated to 22℃ and tested at 22℃ was significantly greater than PTM of animals acclimated to 22℃ and tested at 2℃, which indicated that the animals acclimated to a particular temperature have enhanced locomotor performance in that temperature relative to the animals acclimated to that temperature in other thermal environment. WS of the animals acclimated to 22℃ and tested at 22℃ was significantly faster than WS of animals acclimated to 2℃ and tested at 22℃, PTM of the animals acclimated to 22℃ and tested at 22℃ was significantly greater than PTM of animals acclimated to 2℃ and tested at 22℃. These results supported the BAH. It could be concluded that the PT and thermal acclimation as well as the interaction between the PT and AT significantly influence the locomotor performance of M.hufelandi, and that, despite the existence of a few results of this study that don’t support the BAH, some results of this study support for this hypothesis, and that the animals acclimated to a particular temperature have enhanced locomotor performance in that temperature relative to the animals acclimated to that temperature in other thermal environment, implying that any performance temperature that deviates from the acclimation temperature could cause the reduction of the walking speed which is closely related to the fitness of the M.hufelandi.

Recent developments in photoacoustic imaging and sensing for nondestructive testing and evaluation

Photoacoustic(PA)imaging has been widely used in biomedical research and preclinical studies during the past two decades.It has also been explored for nondestructive testing and evaluation(NDT/E)and for industrial applications.This paper describes the basic principles of PA technology for NDT/E and its applications in recent years.PA technology for NDT/E includes the use of a modulated continuous-wave laser and a pulsed laser for PA wave excitation,PA-generated ultrasonic waves,and all-optical PA wave excitation and detection.PA technology for NDT/E has demonstrated broad applications,including the imaging of railway cracks and defects,the imaging of Li metal batteries,the measurements of the porosity and Young’s modulus,the detection of defects and damage in silicon wafers,and a visualization of underdrawings in paintings.

Investigation of Eddy Current Nondestructive Testing for Carbon Fiber-Reinforced Plastic （CFRP） Based on Electromagnetic Field Analysis

CFRP （carbon fiber reinforced plastic） is used extensively in aircraft and spacecraft structures, because of its excellent mechanical properties. Ultrasonic testing, which is used as a non-destructive testing technique for CFRP, requires a contact medium. In contrast, eddy current testing does not require a contact medium, and when used for CFRP testing it has advantages not available with other techniques. CFRP is a laminate, with each layer being anisotropically conductive, and the distribution of the induced eddy current is yet to be determined. Here, to determine the eddy current distribution in the detection of flaws in cross-ply CFRP （0°/90°） by using a cross-point probe, we performed an FEM （finite element method） analysis of electromagnetic fields. We investigated the nature of the flaw signals and the differences in eddy current distributions between materials with and without flaws.

Excitation and Detection of Shear Horizontal Waves with Electromagnetic Acoustic Transducers for Nondestructive Testing of Plates

The fundamental shear horizontal（SH0） wave has several unique features that are attractive for long-range nondestructive testing（NDT）. By a careful design of the geometric configuration, electromagnetic acoustic transducers（EMATs） have the capability to generate a wide range of guided wave modes, such as Lamb waves and shear-horizontal（SH） waves in plates. However, the performance of EMATs is influenced by their parameters. To evaluate the performance of periodic permanent magnet（PPM） EMATs, a distributed-line-source model is developed to calculate the angular acoustic field cross-section in the far-field. Numerical analysis is conducted to investigate the performance of such EMATs with different geometric parameters, such as period and number of magnet arrays, and inner and outer coil widths. Such parameters have a great influence on the directivity of the generated SH0 waves that arises mainly in the amplitude and width of both main and side lobes. According to the numerical analysis, these parameters are optimized to obtain better directivity. Optimized PPM EMATs are designed and used for NDT of strip plates. Experimental results show that the lateral boundary of the strip plate has no perceivable influence on SHO-wave propagation, thus validating their used in NDT. The proposed model predicts the radiation pattern ofPPM EMATs, and can be used for their parameter optimization.

Statistical analysis of nondestructive testing results of cast steel joints in civil engineering structures

To study the distribution law and random characteristics of casting defects in steel castings,24 civil engineering structural cast steel joints were divided into two groups:simple cast steel joints and complex cast steel joints.Three kinds of nondestructive testing(NDT)methods,namely,visual,magnetic particle,and ultrasonic inspections,were used to detect the macroscopic defects in joints.The NDT results were then statistically analyzed.The results show that the unfused core support is a common defect of complex cast steel joints,and the defect can be seen visually,so excavation and repair welding should be carried out before castings leave factories.Casting cracks are extremely likely to occur in the intersection area of tubes,which is called the ultrasonic inspection blind zone.The occurrence probability of gas pores on simple cast steel joints is the largest,and the occurrence probability of core support incomplete fusions on complex cast steel joints is the largest.However,when cast steel joints are counted as a whole sample,the occurrence probability of gas pores is larger than that of core support incomplete fusions.Therefore,it is the most common defect in cast steel joints.

Ultrasonic Nondestructive Testing of Superplastic Solid-State Welding Joint for Different Steels

Based on quantitative microscopic examinations of welds and welding rate for different steels(40Cr and T10A) joint,which possess the ultra-fine microstructure after high frequency hardening(HFH) and salt-bath cyclic quenching(SCQ),the suitable defect grey scale threshold value was determined,and the welding rate of superplastic solid-state welding of different steels(40Cr and T10 A steel) was systematically inspected and analyzed by means of self-made ultrasonic imaging inspection system.The experimental results showed that the superplastic solid-state weld of different steels can be inspected more accurately,reliably and quickly by this system,and the results were in good accordance with that of metallographic observation.The welding rate of superplastic welding is in linear relation with tensile strength of joint.

Development and application of WGQ type micro-computer-based electromagnetic nondestructive testing instrument for quality of metal material

The WGQ type micro computer based electromagnetic nondestructive testing instrument for quality of metal material was developed on the principle of electromagnetic induction. The invention and marketing of the WGQ instrument has solved the world wide tough problem of the "N" shape relation between the indicated values of testing instruments and the hardness of most metal parts, particularly steel and iron parts. It has also greatly improved the hardness testing precision of aluminium alloy. Consequently the instrument can accurately perform either the quantitative testing of aluminium alloy, steel and iron parts hardness or the qualitative testing of their internal and external defects such as cracks, over burnt and so on. Its hardness testing precision is HRB±0.7, HRC±1 and HB±10. The testing speed can reach 1 500 parts per hour. The instrument has already been successfully applied to the spot of lots of factories.

Silymarin in non alcoholic fatty liver disease

AIM: This study was undertaken to evaluate the hepatic effects of silybum marianum on non alcoholic fatty liver disease (NAFLD). METHODS: In 72 patients affected by NAFLD, main metabolic, hepatic and anti-inflammatory parameters were assayed after 3 mo of a restricted diet and before silymarin treatment (twice a day orally). The brightness of liver echography texture (hepatorenal ratio brightness) was also defined at same time. These evaluations were repeated after 6 mo of treatment. RESULTS: Serum levels of some metabolic and anti-inflammatory data nonsignificantly lowered after 6 mo of silymarin. On the contrary, Steato test, alanine aminotransferase (ALT), aspartate aminotransferase (AST) and gamma-glutamyl transpeptidase were significantly (P < 0.001) reduced. Instead, the AST/ALT ratio unchanged. Finally, the hepatorenal brightness ratio, as an index of hepatic steatosis, significantly (P < 0.05) dropped. CONCLUSION: The obtained results indicate that silymarin appears to be effective to reduce the biochemical, inflammatory and ultrasonic indices of hepatic steatosis. Some parameters indicative of early stage of atherosclerosis were also lowered.

Effectiveness of Co-Testing in Cervical Cancer Screening Program in Macao SAR

Background: Cervical cancer remains a significant public health concern in Macao SAR despite the implementation of a cervical cancer screening program and HPV vaccination. To improve early detection, Macao SAR introduced HPV DNA testing alongside cytology (co-testing) as the primary screening method in 2019. This study evaluates the effectiveness of co-testing in identifying cervical precancerous lesions (CIN2+) compared to cytology alone. Methods: We conducted a retrospective analysis of women aged 30 - 65 years who participated in the routine cervical cancer screening program in Macao SAR Primary Healthcare Centers from 2019 to 2022. Data from over 70,000 women were analyzed, comparing the detection rates of CIN2+ through co-testing and cytology alone. Women with abnormal cytology or positive HPV results were referred for colposcopy. Results: The introduction of co-testing led to a significant increase in the detection of CIN2+, particularly in women with atypical squamous cells of undetermined significance (ASCUS) or negative for intraepithelial lesion or malignancy (NILM) cytology results. Between 2019 and 2022, the percentage of women with ASCUS/NILM and any high-risk HPV (hrHPV) positive who were diagnosed with CIN2+ after colposcopy were 24%, 13%, 10% and 7.5% respectively. This highlights the ability of co-testing to identify high-risk individuals who would have been missed by cytology alone. Discussion: Our findings demonstrate the effectiveness of co-testing in improving the sensitivity of cervical cancer screening in Macao SAR. The inclusion of HPV DNA testing allows for better risk stratification of women with ASCUS/NILM cytology, leading to more targeted referrals for colposcopy and timely detection of precancerous lesions. The initial high positive rate in 2019 (24%) might be attributed to the small sample size and potentially reflects a backlog of undiagnosed cases prior to co-testing implementation. Conclusion: The implementation of co-testing in Macao SAR’s cervical cancer screening program significantly improves the early detection of precancerous lesions, particularly in women with ambiguous cytology results. This proactive approach contributes to reducing cervical cancer morbidity and mortality and improving women’s health outcomes in Macao SAR.

NUMERICAL SIMULATION OF ULTRASONIC NONDESTRUCTIVE TESTING FOR WELDS

A computer simulation technique for ultrasonic propagation is utilized for the simulation of ultrasonic nondestructive testing (NDT). In this paper, one goal of the simulation is to compute ultrasonic field radiated by arbitrary transducers into pieces under examination. The other simulates a testing experiment. The simulation approach is based on the model for the computation of the ultrasonic field in isotropic media radiated from actual NDT transducers. After the field is known, remaining to be modeled is the interaction between this field and the scatters (defect) and the echo structure. The model of beam-defect interaction is based on the Kirchhoff’s diffraction approximations theory applied to elastodynamics. We assumed that the incident wave fronts on the defect are plane in the case of a focused immersed transducer and material is isotropic and homogeneous. The simulating results demonstrate that the model in ultrasonic NDT of welds is practical in further research and useful in optimizing testi

Fast and Accurate Identification of <i>M. tuberculosis</i>Complex Using an Immunochromatographic MPT64 Antigen Detection Test

Background: A new rapid Immunochromatographic test (ICT) kit (MPT64 TB Ag Kit) for detection of MPT64 Antigen in M. tuberculosis (MTB) isolates used for rapid identification of MTB isolates developed by SD (Standard Diagnostics) Bio line, South Korea was evaluated. The ICT is a rapid, reliable and cheaper method that can be used instead of conventional biochemical tests for confirming MTB in culture isolates in resource limited laboratories. The study also evaluated the ability of ICT to detect MPT64-Antigen before the micro MGIT could signal positive. Material/Methods: A total of 450 sputum samples of individual patients were used for the study. 152 isolates of Mycobacteria were recovered from solid and liquid media. These strains were tested for the detection of MPT64-antigen. H37Rv strain was served as the positive reference control and also used for early detection of Antigen experiment. Findings: The development of bands on both test and sample region when H37Rv strain was tested were seen (MPT64 antigen positive). When 138 MTB isolates were tested, it showed a similar banding pattern indicating 100% sensitivity. MPT64 band formation was not detected in any of the 14 isolates indicating 100% specificity. Both PPV & NPV were 100%. All the isolates negative for MPT64 Ag were confirmed as MOTT by conventional bio-chemical PNBA. The H37Rv strain showed a faint band from the 2nd day onwards from inoculation till 3rd day in the earlier Antigen detection experiment. Conclusion: Rapid identification of MTB culture isolate is a pressing need for diagnosis and proceeding to perform drug susceptibility testing. MPT64 TB Ag detection ICT kit is a rapid, reliable method, good substitute for molecular identification methods, and conventional biochemical test which is time-consuming and technically demanding. The early detection of Antigen can be used as an effective tool in diagnosis.

Genetic testing vs microforceps biopsy in pancreatic cysts:Systematic review and meta-analysis

BACKGROUND Carcinoembryonic antigen(CEA)and cytology in pancreatic cystic fluid are suboptimal for evaluation of pancreatic cystic neoplasms.Genetic testing and microforceps biopsy are promising tools for pre-operative diagnostic improvement but comparative performance of both methods is unknown.AIM To compare the accuracy of genetic testing and microforceps biopsy in pancreatic cysts referred for surgery.METHODS We performed a literature search in Medline,Scopus,and Web of Science for studies evaluating genetic testing of cystic fluid and microforceps biopsy of pancreatic cysts,with endoscopic ultrasound with fine-needle aspiration(EUSFNA)prior to surgery and surgical pathology as reference standard for diagnosis.We evaluated the diagnostic accuracy for:1-benign cysts;2-mucinous low-risk cysts;3-high-risk cysts,and the diagnostic yield and rate of correctly identified cysts with microforceps biopsy and molecular analysis.We also assessed publication bias,heterogeneity,and study quality.RESULTS Eight studies,including 1206 patients,of which 203(17%)referred for surgery who met the inclusion criteria were analyzed in the systematic review,and seven studies were included in the meta-analysis.Genetic testing and microforceps biopsies were identical for diagnosis of benign cysts.Molecular analysis was superior for diagnosis of both low and high-risk mucinous cysts,with sensitivities of 0.89(95%CI:0.79-0.95)and 0.57(95%CI:0.42-0.71),specificities of 0.88(95%CI:0.75-0.95)and 0.88(95%CI:0.80-0.93)and AUC of 0.9555 and 0.92,respectively.The diagnostic yield was higher in microforceps biopsies than in genetic analysis(0.73 vs 0.54,respectively)but the rates of correctly identified cysts were identical(0.73 with 95%CI:0.62-0.82 vs 0.71 with 95%CI:0.49-0.86,respectively).CONCLUSION Genetic testing and microforceps biopsies are useful second tests,with identical results in benign pancreatic cysts.Genetic analysis performs better for low-and high-risk cysts but has lower diagnostic yield.

Relationship Between Gene-Phenotype and Clinical Manifestations of Chromosomal Copy Number Variations Indicated by Non-Invasive Prenatal Testing

Objective:To analyze the clinical value of non-invasive prenatal testing(NIPT)in detecting chromosomal copy number variations(CNVs)and to explore the relationship between gene expression and clinical manifestations of chromosomal copy number variations.Methods:3551 naturally conceived singleton pregnant women who underwent NIPT were included in this study.The NIPT revealed abnormalities other than sex chromosome abnormalities and trisomy 13,18,and 21.Pregnant women with chromosome copy number variations underwent genetic counseling and prenatal ultrasound examination.Interventional prenatal diagnosis and chromosome microarray analysis(CMA)were performed.The clinical phenotypes and pregnancy outcomes of different prenatal diagnoses were analyzed.Additionally,a follow-up was conducted by telephone to track fetal development after birth,at six months,and one year post-birth.Results:A total of 53 cases among 3551 cases showed chromosomal copy number variation.Interventional prenatal diagnosis was performed in 36 cases:27 cases were negative and 8 were consistent with the NIPT test results.This indicates that NIPT’s positive predictive value(PPV)in CNVs is 22.22%.Conclusion:NIPT has certain clinical significance in screening chromosome copy number variations and is expected to become a routine screening for chromosomal microdeletions and microduplications.However,further interventional prenatal diagnosis is still needed to identify fetal CNVs.

Field testing of shear strength of granite residual soils

The characteristics of residual soils are very different from those of sedimentary soils.Although the strength characteristics of sedimentary soils have been studied extensively,the shear strength characteristics of granitic residual soils(GRS)subjected to the weathering of parent rocks have rarely been investigated.In this study,the shear strength characteristics of GRS in the Taishan area of southeast China(TSGRS)were studied by field and laboratory tests.The field tests consisted of a cone penetration test(CPT),borehole shear test(BST),self-boring pressuremeter test(SBPT),and seismic dilatometer Marchetti test(SDMT).The shortcomings of laboratory testing are obvious,with potential disturbances arising through the sampling,transportation,and preparation of soil samples.Due to the special structure of GRS samples and the ease of disturbance,the results obtained from laboratory tests were generally lower than those obtained from situ tests.The CPT and scanning electron microscopy(SEM)results indicated significant weathering and crustal hardening in the shallow TSGRS.This resulted in significant differences in the strength and strength parameters of shallow soil obtained by the BST.Based on the SDMT and SBPT results,a comprehensive evaluation method of shear strength for TSGRS was proposed.The SBPT was suitable for evaluating the strength of shallow GRS.The material index(ID)and horizontal stress index(KD)values obtained by the SDMT satisfied the empirical relationship proposed by Marchetti based on the ID index,and were therefore considered suitable for the evaluation of the shear strength of deep GRS.

Correction to: Recent developments in photoacoustic imaging and sensing for nondestructive testing and evaluation

Following publication of the original article[1],the authors identified an error in the article title.The first word ‘Review’ is added mistakenly by the typesetter.