A Cross-Layer Optimization Framework for Energy Efficiency in Wireless Sensor Networks

We consider the extension of network lifetime of battery driven wireless sensor networks by splitting the sensing area into uniform clusters and implementing heterogeneous modulation schemes at different members of the clusters. A cross-layer optimization has been proposed to reduce total energy expenditure of the network;at network layer, routing is done through uniform clusters;at MAC layer, each sensor node of the cluster is assigned fixed or variable time slots and at physical layer different member of the clusters is assigned different modulation techniques. MATLAB simulation proved substantial network lifetime gains.

Müller cells are activated in response to retinal outer nuclear layer degeneration in rats subjected to simulated weightlessness conditions

A microgravity environment has been shown to cause ocular damage and affect visual acuity,but the underlying mechanisms remain unclear.Therefore,we established an animal model of weightlessness via tail suspension to examine the pathological changes and molecular mechanisms of retinal damage under microgravity.After 4 weeks of tail suspension,there were no notable alterations in retinal function and morphology,while after 8 weeks of tail suspension,significant reductions in retinal function were observed,and the outer nuclear layer was thinner,with abundant apoptotic cells.To investigate the mechanism underlying the degenerative changes that occurred in the outer nuclear layer of the retina,proteomics was used to analyze differentially expressed proteins in rat retinas after 8 weeks of tail suspension.The results showed that the expression levels of fibroblast growth factor 2(also known as basic fibroblast growth factor)and glial fibrillary acidic protein,which are closely related to Müller cell activation,were significantly upregulated.In addition,Müller cell regeneration and Müller cell gliosis were observed after 4 and 8 weeks,respectively,of simulated weightlessness.These findings indicate that Müller cells play an important regulatory role in retinal outer nuclear layer degeneration during weightlessness.

Exploring the effect of aggregation-induced emission on the excited state intramolecular proton transfer for a bis-imine derivative by quantum mechanics and our own n-layered integrated molecular orbital and molecular mechanics calculations

We theoretically investigate the excited state intramolecular proton transfer(ESIPT) behavior of the novel fluorophore bis-imine derivative molecule HNP which was designed based on the intersection of 1-(hydrazonomethyl)-naphthalene-2-ol and 1-pyrenecarboxaldehyde. Especially, the density functional theory(DFT) and time-dependent density functional theory(TDDFT) methods for HNP monomer are introduced. Moreover, the "our own n-layered integrated molecular orbital and molecular mechanics"(ONIOM) method(TDDFT:universal force field(UFF)) is used to reveal the aggregation-induced emission(AIE) effect on the ESIPT process for HNP in crystal. Our results confirm that the ESIPT process happens upon the photoexcitation for the HNP monomer and HNP in crystal, which is distinctly monitored by the optimized geometric structures and the potential energy curves. In addition, the results of potential energy curves reveal that the ESIPT process in HNP will be promoted by the AIE effect. Furthermore, the highest occupied molecular orbital(HOMO) and lowest unoccupied molecular orbital(LUMO) for the HNP monomer and HNP in crystal have been calculated. The calculation demonstrates that the electron density decrease of proton donor caused by excitation promotes the ESIPT process. In addition, we find that the variation of atomic dipole moment corrected Hirshfeld population(ADCH) charge for proton acceptor induced by the AIE effect facilitates the ESIPT process. The results will be expected to deepen the understanding of ESIPT dynamics for luminophore under the AIE effect and provide insight into future design of high-efficient AIE compounds.

光学薄膜中界面层和表面吸附层对相位延迟的影响

多层介质反射镜在非正入射的时候,两个不同的偏振态之间会产生不同的相移.根据空气与膜层、膜层之间的实际情况,建立了界面层和表面吸附层模型,并运用它分析相位延迟产生误差的原因.通过优化设计,入射角为54°,在1285～1345nm之间p,s波获得了270±1°的相移,同时也使反射率在99.5%以上.用离子束溅射技术制备相位延迟膜,用分光光度计测试了光谱特性和用椭偏仪测试了相位特性,在相应波段获得了262.4±1.8°的相移,同时也使反射率在99.6%以上.误差的主要来源是离子源工作特性会产生不均匀的过渡层和最外层会吸收一些水汽、灰尘等也产生表面过渡层.由误差分析得出了制备中过渡层的物理厚度和折射率的变化情况,最外层的厚度误差和折射率偏差是发生相移偏小的主要因素.

Endoscopic and surgical resection of T1a/T1b esophageal neoplasms: A systematic review

AIM: To investigate potential therapeutic recommendations for endoscopic and surgical resection of T1a/ T1b esophageal neoplasms. METHODS: A thorough search of electronic databases MEDLINE, Embase, Pubmed and Cochrane Library, from 1997 up to January 2011 was performed. An analysis was carried out, pooling the effects of outcomes of 4241 patients enrolled in 80 retrospective studies. For comparisons across studies, each reporting on only one endoscopic method, we used a random effects meta-regression of the log-odds of the outcome of treatment in each study. "Neural networks" as a data mining technique was employed in order to establish a prediction model of lymph node status in superficial submucosal esophageal carcinoma. Another data mining technique, the "feature selection and root cause analysis", was used to identify the most impor-tant predictors of local recurrence and metachronous cancer development in endoscopically resected patients, and lymph node positivity in squamous carcinoma (SCC) and adenocarcinoma (ADC) separately in surgically resected patients. RESULTS: Endoscopically resected patients: Low grade dysplasia was observed in 4% of patients, high grade dysplasia in 14.6%, carcinoma in situ in 19%, mucosal cancer in 54%, and submucosal cancer in 16% of patients. There were no significant differences between endoscopic mucosal resection and endoscopic submucosal dissection (ESD) for the following parameters: complications, patients submitted to surgery, positive margins, lymph node positivity, local recurrence and metachronous cancer. With regard to piecemeal resection, ESD performed better since the number of cases was significantly less [coefficient: -7.709438, 95%CI: (-11.03803, -4.380844), P < 0.001]; hence local recurrence rates were significantly lower [coefficient: -4.033528, 95%CI: (-6.151498, -1.915559),P < 0.01]. A higher rate of esophageal stenosis was observed following ESD [coefficient: 7.322266, 95%CI: (3.810146, 10.83439), P < 0.001]. A significantly greater number of SCC patients were submitted to surgery (log-odds, ADC: -2.1206 ± 0.6249 vs SCC: 4.1356 ± 0.4038, P < 0.05). The odds for re-classification of tumor stage after endoscopic resection were 53% and 39% for ADC and SCC, respectively. Local tumor recurrence was best predicted by grade 3 differentiation and piecemeal resection, metachronous cancer development by the carcinoma in situ component, and lymph node positivity by lymphovascular invasion. With regard to surgically resected patients: Significant differences in patients with positive lymph nodes were observed between ADC and SCC [coefficient: 1.889569, 95%CI: (0.3945146, 3.384624), P<0.01). In contrast, lymphovascular and microvascular invasion and grade 3 patients between histologic types were comparable, the respective rank order of the predictors of lymph node positivity was: Grade 3, lymphovascular invasion (L+), microvascular invasion (V+), submucosal (Sm) 3 invasion, Sm2 invasion and Sm1 invasion. Histologic type (ADC/SCC) was not included in the model. The best predictors for SCC lymph node positivity were Sm3 invasion and (V+). For ADC, the most important predictor was (L+). CONCLUSION: Local tumor recurrence is predicted by grade 3, metachronous cancer by the carcinoma insitu component, and lymph node positivity by L+. T1b cancer should be treated with surgical resection.

Cycling performance of layered oxide cathode materials for sodium-ion batteries

Layered oxide is a promising cathode material for sodium-ion batteries because of its high-capacity,high operating voltage,and simple synthesis.Cycling performance is an important criterion for evaluating the application prospects of batteries.However,facing challenges,including phase transitions,ambient stability,side reactions,and irreversible anionic oxygen activity,the cycling performance of layered oxide cathode materials still cannot meet the application requirements.Therefore,this review proposes several strategies to address these challenges.First,bulk doping is introduced from three aspects:cationic single doping,anionic single doping,and multi-ion doping.Second,homogeneous surface coating and concentration gradient modification are reviewed.In addition,methods such as mixed structure design,particle engineering,high-entropy material construction,and integrated modification are proposed.Finally,a summary and outlook provide a new horizon for developing and modifying layered oxide cathode materials.

Structures and Properties of Iron Matrix Composites with Tungsten Carbide Particle by EPC-V Process

In this paper the Expendable Pattern Casting with dry sand Vacuum(EPC-V) process is used to manufacture iron matrix composites with tungsten carbide particle.Microstructures of the composites layers were analyzed.The abrasive wear resistance of the composites layers were tested and compared with that of high chromium cast iron.The results show that the iron matrix composites with tungsten carbide particle have high hardness.The abrasive wear resistance of composites with tungsten carbide particle is higher than that of high chromium cast iron.The properties of the matrix materials have been improved remarkably.

Dynamic compression characteristics of layered rock mass of significant strength changes in adjacent layers

Layered rock mass of significant strength changes for adjacent layers is frequently observed in underground excavation,and dynamic loading is a prevalent scenario generated during excavation.In order to improve the driving efficiency and reduce engineering accidents,dynamic compression characteristics of this kind of rock mass should be understood.The dynamic properties of a layered composite rock mass are investigated through a series of rock tests and numerical simulations.The rock mass is artificially made of various proportions of sand,cement and water to control the distinct strength variations at various composite layers separated by parallel bedding planes.All rock specimens are prefabricated in a specially designed mould and then cut into 50 mm in diameter and 50 mm in height for split Hopkinson pressure bar(SHPB)dynamic compression testing.The test results reveal that increasing strain rate causes the increases of peak strength,σ_p,and the corresponding failure strain,ε_p,while the dynamic elastic modulus,E_d,remains almost unchanged.Interestingly,under the same strain rates,Ed of the composite rock specimen is found to decline first and then increase as the dip angle of bedding plane increases.The obtained rock failure patterns due to various dip angles lead to failure modes that could be classified into four categories from our dynamic tests.Also,a series of counterpart numerical simulations has been undertaken,showing that dynamic responses are in good agreement with those obtained from the SHPB tests.The numerical analysis enables us to Iook into the dynamic characteristics of the composite rock mass subjected to a broader range of strain rates and dip angles than these being tested.

EECLP: AWireless Sensor Networks Energy Efficient Cross-Layer Protocol

Recent advancements in wireless communications have allowed the birth of novel wireless sensor networks(WSN).A sensor network comprises several micro-sensors deployed randomly in an area of interest.A micro-sensor is provided with an energy resource to supply electricity to all of its components.However,the disposed energy resource is limited and battery replacement is generally infeasible.With this restriction,the sensors must conserve energy to prolong their lifetime.Various energy conservation strategies for WSNs have been presented in the literature,from the application to the physical layer.Most of these solutions focus only on optimizing a single layer in terms of energy consumption.In this research,a novel cross-layer technique for WSNs’effective energy usage is presented.Because most energy consumption factors exist in the Medium Access Control(MAC)layer and network layer,our EECLP protocol(Energy Efficient Cross-Layer Protocol for Wireless Sensor Networks)integrates these two layers to satisfy energy efficiency criteria.To gain access to the transmission channel,we implement a communication regime at the MAC layer based on CSMA/CA(Carrier Sense Multiple Access/Collision Avoidance)techniques.Next,depending on the activity and a standby period,we employ the RTS/CTS(Request to Send/Clear to Send)method to prevent collisions and resolve hidden node concerns by utilizing the network allocation vector(NAV)to calculate the transmission duration.Employing a greedy strategy,we establish chains amongst cluster members to mitigate the issue of high energy consumption in routing data.An objective function was utilized to determine the optimal cross-chain path based on the distances to the base station(BS)and residual energy(RE).The simulation,testing,and comparison of the proposed protocol to peer protocols have shown superior outcomes and a prolonged network lifespan.Using the suggested protocol,the network lifetime increases by 10%compared to FAMACO(Fuzzy and Ant Colony Optimization based MAC/Routing Cross-layer)protocol,and it increases by 90%and 95%compared to IFUC(Improved Fuzzy Unequal Clustering)and UHEED(Unequal Hybrid Energy Efficient and Distributed)protocols successively.

Cross-layer design of combining AMC with HARQ in cooperative relay system with perfect and imperfect CSI

A cross-layer design which combines adaptive modulation and coding (AMC) at the physical layer with a hybrid automatic repeat request (HARQ) protocol at the data link layer (LL) is presented, in cooperative relay system over Nakagami-m fading channels with perfect and imperfect channel state information (CSI). In order to maximize spectral efficiency (SE) under delay and packet error rate (PER) performance constraints, a state transition model and an optimization framework with perfect CSI are presented. Then the framework is extended to cooperative relay system with imperfect CSI. The numerical results show that the scheme can achieve maximum SE while satisfying transmitting delay requirements. Compared with the imperfect CSI, the average PER with perfect CSI is much lower and the spectral efficiency is much higher.

Investigation of the Relation between Rolling Contact Fatigue Property and Microstructure on the Surface Layer of D2 Wheel Steel

Through the rolling contact fatigue experiment under the condition of the lubricating oil, this article investigated the relation between contact fatigue property and microstructure on the surface layer of D2 wheel steel. The results showed that although the roughness of the original specimen induced by mechanical processing would diminish to some extent in the experiment, the 0.5 - 1.5 μm thick layer of ultrafine microstructure on the original mechanically-processed specimen surface would still become micro-cracks and small spalling pits due to spalling, and would further evolve into fatigue crack source. Additionally, even under the impact of the load that was not adequate to make the material reach fatigue limit, the ferrite in the microstructure underwent plastic deformation, which led the refinement of proeutectoid ferrite grains. During the experiment, the hardening and the refinement caused by plastic deformation consisted with the theory that dislocation gave rise to plastic deformation and grain refinement. The distribution laws of hardness and ferrite grain sizes measured could be explained by the distribution law of the shearing stress in the subsurface.

Fault characteristics and control on hydrocarbon accumulation of middle-shallow layers in the slope zone of Mahu sag, Junggar Basin, NW China

The development, evolution and formation mechanism of faults and their control on the migration and accumulation of Mesozoic oil and gas in the middle-shallow layers of the slope zone of Mahu sag were studied by the interpretation of seismic and drilling data. Two types of faults, normal and strike-slip, are developed in the middle-shallow layers of the slope zone of the Mahu sag and they are mostly active in the Yanshanian period. They are divided into four grade faults: The grade I strike-slip faults with NWW to near EW direction are related to the left-lateral transpressive fault zones in the northwest of Junggar Basin since the end of the Triassic. The grade II faults with NE to NNE direction are the normal faults located at the junction of the fault zone and the slope zone, and their formation is related to the extension at the top of the nose-like structures in the fault zone. The grade III faults, which are also the normal faults, are the result of the extension at the top of the lower uplifts in the slope zone and differential compaction. The grade IV faults with NE direction are normal faults, which may be related to the extension environment at the tip of the lower uplifts. Faults not only are the channel for the vertical migration of oil and gas, but also control the oil-gas accumulation. There are two types of oil-gas reservoirs in the middle-shallow layers of slope zone of Mahu sag: fault block reservoirs and fault-lithologic reservoirs. They have large traps and promising exploration potential.

超细层状材料A_2La_2Ti_3O_(10)(A=Na,K)的低温合成及表征

s: Ultrafine A2La2Ti3O10 (A=K, Na) powders with laminar structure were successfully synthesized by citric acid sol-gel method using ANO3(A=K, Na)?La(NO3)3?Ti(OBu)4 and citric acid as starting precursors. The crystalline phase of A2La2Ti3O10 can be obtained by thermal decomposition of citrate complex precursors at a relatively low temperature of 800 ℃ (600 ℃ for A=Na), about 300 ℃(500 ℃ for A=Na) lower than that of conventional solid state reaction process. The properties of the citrate precursors and the calcined powders were characterized by Infrared spectroscopy (IR), X-ray diffraction (XRD), transmission electron microscopy (TEM), thermal-gravimetric-differential thermal analysis (TG-DTA), inductively coupled plasma (ICP) and Brunauer-Emmett-Teller (BET) techniques. Results show that the average size of A2La2Ti3O10 powders obtained by citric acid sol-gel route was reduced to 200 nm×250 nm and the specific surface area was up to 19 m2·g-1. At the same time, the product was with more regular morphological characteristics. The synthesis process and the formation of A2La2Ti3O10 were also discussed. The obtained A2La2Ti3O10 was found to be transformed from A2La2Ti3O9.5 during the formation process.

Trend judgment of abandoned channels and fine architecture characterization in meandering river reservoirs: A case study of Neogene Minhuazhen Formation NmⅢ2 layer in Shijiutuo bulge, Chengning uplift, Bohai Bay Basin, East China

Based on well logging responses,sedimentary patterns and sandstone thickness,the distribution characteristics of meandering river sedimentary sand body of Neogene Minghuazhen Formation NmⅢ2 layer in the west of Shijiutuo Bulge,Chengning Uplift,Bohai Bay Basin were investigated.A new approach to calculate the occurrence of the sand-mudstone interfaces using resistivity log of horizontal well was advanced to solve the multiple solution problem of abandoned channel’s orientation.This method uses the trigonometric function relationship between radius,dip and length of the resistivity log to calculate the occurrence qualitatively-quantitatively to help determine the true direction of the abandoned channels.This method can supplement and improve the architecture dissection technique for meandering river sandbodies.This method was used to study the dip angle and scale of the lateral accretion layers in point bar quantitatively to help determine the spatial distribution of lateral accretion layers.The fine architecture model of underground meandering river reservoir in the study area has been established.Different from traditional grids,different grid densities for lateral accretion layers and bodies were used in this model by non-uniform upscaling to establish the inner architecture model of point-bars and realize industrial numerical simulation of the whole study area.The research results can help us predict the distribution of remaining oil,tap remaining oil,and optimize the waterflooding in oilfields.

Enhancing layered perovskite ferrites with ultra-high-density nanoparticles via cobalt doping for ceramic fuel cell anode

Nanoparticles anchored on the perovskite surface have gained considerable attention for their wide-ranging applications in heterogeneous catalysis and energy conversion due to their robust and integrated structural configuration.Herein,we employ controlled Co doping to effectively enhance the nanoparticle exsolution process in layered perovskite ferrites materials.CoFe alloy nanoparticles with ultra-high-density are exsolved on the(PrBa)_(0.95)(Fe_(0.8)Co_(0.1)Nb_(0.1))2O_(5+δ)(PBFCN_(0.1))surface under reducing atmosphere,providing significant amounts of reaction sites and good durability for hydrocarbon catalysis.Under a reducing atmosphere,cobalt facilitates the reduction of iron cations within PBFCN_(0.1),leading to the formation of CoFe alloy nanoparticles.This formation is accompanied by a cation exchange process,wherein,with the increase in temperature,partial cobalt ions are substituted by iron.Meanwhile,Co doping significantly enhance the electrical conductivity due to the stronger covalency of the Cosingle bondO bond compared with Fesingle bondO bond.A single cell with the configuration of PBFCN_(0.1)-Sm_(0.2)Ce_(0.8)O_(1.9)(SDC)|SDC|Ba_(0.5)Sr_(0.5)Co_(0.8)Fe_(0.2)O_(3−δ)(BSCF)-SDC achieves an extremely low polarization resistance of 0.0163Ωcm^(2)and a high peak power density of 740 mW cm^(−2)at 800℃.The cell also shows stable operation for 120 h in H_(2)with a constant current density of 285 mA cm^(−2).Furthermore,employing wet C_(2)H_(6)as fuel,the cell demonstrates remarkable performance,achieving peak power densities of 455 mW cm^(−2)at 800℃and 320 mW cm^(−2)at 750℃,marking improvements of 36%and 70%over the cell with(PrBa)_(0.95)(Fe_(0.9)Nb_(0.1))_(2)O_(5+δ)(PBFN)-SDC at these respective temperatures.This discovery emphasizes how temperature influences alloy nanoparticles exsolution within doped layered perovskite ferrites materials,paving the way for the development of high-performance ceramic fuel cell anodes.

Probing the electric double layer structure at nitrogen-doped graphite electrodes by constant-potential molecular dynamics simulations

Electric double layer(EDL)is a critical topic in electrochemistry and largely determines the working performance of lithium batteries.However,atomic insights into the EDL structures on heteroatom-modified graphite anodes and EDL evolution with electrode potential are very lacking.Herein,a constant-potential molecular dynamics(CPMD)method is proposed to probe the EDL structure under working conditions,taking N-doped graphite electrodes and carbonate electrolytes as an example.An interface model was developed,incorporating the electrode potential and atom electronegativities.As a result,an insightful atomic scenario for the EDL structure under varied electrode potentials has been established,which unveils the important role of doping sites in regulating both the EDL structures and the following electrochemical reactions at the atomic level.Specifically,the negatively charged N atoms repel the anions and adsorb Li~+at high and low potentials,respectively.Such preferential adsorption suggests that Ndoped graphite can promote Li~+desolvation and regulate the location of Li~+deposition.This CPMD method not only unveils the mysterious function of N-doping from the viewpoint of EDL at the atomic level but also applies to probe the interfacial structure on other complicated electrodes.

Stabilized Nickel-Rich-Layered Oxide Electrodes for High-Performance Lithium-Ion Batteries

This work made use of the Aalto University Otanano-Nanomicroscopy Center and RAMI infrastructures.Financial support from Business Finland NextGenBat[grant number 211849]is greatly acknowledged.The tomography experiment was performed at the beamline ID16B of the European Synchrotron Radiation Facility(ESRF),Grenoble,France,in the frame of proposal CH-6644.The patent titled“Stabilized Positive Electrode Material to Enable High Energy and Power Density Lithium-Ion Batteries”(IPD3173)is pertinent to this manuscript.It was filed by Zahra Ahaliabadeh and Tanja Kallio,and the patent rights are held by Aalto University.

Shear mechanical properties and fracturing responses of layered rough jointed rock-like materials

This study aims to investigate mechanical properties and failure mechanisms of layered rock with rough joint surfaces under direct shear loading.Cubic layered samples with dimensions of 100 mm×100 mm×100 mm were casted using rock-like materials,with anisotropic angle(α)and joint roughness coefficient(JRC)ranging from 15°to 75°and 2-20,respectively.The direct shear tests were conducted under the application of initial normal stress(σ_(n)) ranging from 1-4 MPa.The test results indicate significant differences in mechanical properties,acoustic emission(AE)responses,maximum principal strain fields,and ultimate failure modes of layered samples under different test conditions.The peak stress increases with the increasingαand achieves a maximum value atα=60°or 75°.As σ_(n) increases,the peak stress shows an increasing trend,with correlation coefficients R² ranging from 0.918 to 0.995 for the linear least squares fitting.As JRC increases from 2-4 to 18-20,the cohesion increases by 86.32%whenα=15°,while the cohesion decreases by 27.93%whenα=75°.The differences in roughness characteristics of shear failure surface induced byαresult in anisotropic post-peak AE responses,which is characterized by active AE signals whenαis small and quiet AE signals for a largeα.For a given JRC=6-8 andσ_(n)=1 MPa,asαincreases,the accumulative AE counts increase by 224.31%(αincreased from 15°to 60°),and then decrease by 14.68%(αincreased from 60°to 75°).The shear failure surface is formed along the weak interlayer whenα=15°and penetrates the layered matrix whenα=60°.Whenα=15°,as σ_(n) increases,the adjacent weak interlayer induces a change in the direction of tensile cracks propagation,resulting in a stepped pattern of cracks distribution.The increase in JRC intensifies roughness characteristics of shear failure surface for a smallα,however,it is not pronounced for a largeα.The findings will contribute to a better understanding of the mechanical responses and failure mechanisms of the layered rocks subjected to shear loads.

The Effect of a Monatomic Layer on a Surface on the Transition Radiation

The transition radiation of a charged particle crossing the interface of two media having a monatomic impurity layer is investigated. It is shown that at sliding angles of incidence of a particle on the boundary of the media, the transition radiation is mainly determined by the properties of the surface layer. The possibility of using transition radiation to study the surface of substances is discussed. In addition, due to the hard radiation present in space, this research may be important for the use of light monoatomic layers as a material for satellite antennas, “solar sails” and cover layers in a future space (interstellar) mission.