气象观测场在汽车试验场中的应用研究

汽车试验场作为汽车开展道路测试的重要场所,用于验证汽车产品的品质以及可靠性。除了场地道路外,气象条件作为汽车道路测试的重要一环,在《GB/T12534-1990汽车道路试验方法通则》中也有明确要求,如:试验时应是无雨无雾天气,相对湿度小于95%,气温0-40℃,风速不大于3m/s。同时气象条件也作为试验场道路管控的重要依据,实时风速、雨量、能见度等信息为场地管理者发布限速、限行、封场等通知提供必要参考依据,直接影响道路测试安全管控的及时性。因此,文章从气象观测场的建设、气象服务、异常天气道路管控等方面开展气象观测场在汽车试验场中的应用研究。

Prediction of wax precipitation region in wellbore during deep water oil well testing

During deep water oil well testing, the low temperature environment is easy to cause wax precipitation, which affects the normal operation of the test and increases operating costs and risks. Therefore, a numerical method for predicting the wax precipitation region in oil strings was proposed based on the temperature and pressure fields of deep water test string and the wax precipitation calculation model. And the factors affecting the wax precipitation region were analyzed. The results show that: the wax precipitation region decreases with the increase of production rate, and increases with the decrease of geothermal gradient, increase of water depth and drop of water-cut of produced fluid, and increases slightly with the increase of formation pressure. Due to the effect of temperature and pressure fields, wax precipitation region is large in test strings at the beginning of well production. Wax precipitation region gradually increases with the increase of shut-in time. These conclusions can guide wax prevention during the testing of deep water oil well, to ensure the success of the test.

Establishment of Unstable Flow Model and Well Testing Analysis for Viscoelastic Polymer Flooding

At present, the polymer solution is usually assumed to be Newtonian fluid or pseudoplastic fluid, and its elasticity is not considered on the study of polymer flooding well testing model. A large number of experiments have shown that polymer solutions have viscoelasticity, and disregarding the elasticity will cause certain errors in the analysis of polymer solution seepage law. Based on the percolation theory, this paper describes the polymer flooding mechanism from the two aspects of viscous effect and elastic effect, the mathematical model of oil water two-phase three components unsteady flow in viscoelastic polymer flooding was established, and solved by finite difference method, and the well-test curve was drawn to analyze the rule of well test curve in polymer flooding. The results show that, the degree of upward warping in the radial flow section of the pressure recovery curve when considering polymer elasticity is greater than the curve which not considering polymer elasticity. The relaxation time, power-law index, polymer injection concentration mainly affect the radial flow stage of the well testing curve. The relaxation time, power-law index, polymer injection concentration and other polymer flooding parameters mainly affect the radial flow stage of the well testing curve. The larger the polymer flooding parameters, the greater the degree of upwarping of the radial flow derivative curve. This model has important reference significance for well-testing research in polymer flooding oilfields.

Research on Well Testing Interpretation of Low Permeability Deformed Dual Medium Reservoir

Considering the influence of quadratic gradient term and medium deformation on the seepage equation, a well testing interpretation model for low permeability and deformation dual medium reservoirs was derived and established. The difference method was used to solve the problem, and pressure and pressure derivative double logarithmic curves were drawn to analyze the seepage law. The research results indicate that the influence of starting pressure gradient and medium deformation on the pressure characteristic curve is mainly manifested in the middle and late stages. The larger the value, the more obvious the upward warping of the pressure and pressure derivative curve;the parameter characterizing the dual medium is the crossflow coefficient. The channeling coefficient determines the time and location of the appearance of the “concave”. The smaller the value, the later the appearance of the “concave”, and the more to the right of the “concave”.

A method for preventing hydrates from blocking flow during deep-water gas well testing

Based on the research of the formation mechanism and evolution rule of hydrate flow obstacle during deep-water gas well testing,a new method for the prevention of hydrate flow obstacle based on safety testing window is proposed by changing the previous idea of"preventing formation"to the idea of"allowing formation,preventing plugging".The results show that the effective inner diameter of the testing tubing and the wellhead pressure decrease gradually with the formation and precipitation of hydrates during deep-water gas well testing,and it presents three typical processes of slow,fast and sudden changes.There is a safety testing window during deep-water gas well testing.The safety testing window of deep-water gas well testing decreases first and then increases with the increase of gas production rate,and increases with the increase of hydrate inhibitor concentrations.In the case with different testing production rates,a reasonable testing order with alternate low and high gas production rates has been proposed to further reduce the dosage of hydrate inhibitor and even avoid the use of hydrate inhibitors considering the decomposition and fall-off of hydrates.Compared with the traditional methods,the new method based on safety testing window can reduce the dosage of hydrate inhibitor by more than 50%.

Safety Control Technology of Deepwater Perforated Gas Well Testing

Due to the high difficulties, high investment, and high risks in deepwater oil and gas well testing, major safety problems can occur easily. A key to prevent accidents is to conduct safety assessment and control on deepwater testing and to improve the testing technology. The deepwater of the South China Sea has some special environmental features: long distance from offshore, frequent typhoons in summer and constant monsoons in winter, and the presence of sandy slopes, sandy ridges and internal waves, coupled with the complex properties of oil and gas reserves which bring more challenges to deepwater well testing. In combination with deepwater well testing practice in the South China Sea, this paper analyzes the main potential risks in deepwater well testing and concludes that there are risks of failures of testing string, tools, and ground processes. Other risks are gas hydrate blockage, reservoir stratum sanding, and typhoon impacts. Specific precautions are also proposed in response to these risks in the paper.

温度和热驯化对胡氏大生熊虫运动行为的影响

The beneficial acclimation hypothesis (BAH) predicts that animals acclimated to a particular temperature have enhanced performance or fitness at that temperature in comparison with animals acclimated to other temperatures. The BAH has been tested by a variety of empirical examinations, and was rejected by some of them. In order to provide new evidences for the BAH, the effects of acute and acclimation temperature (AT) on locomotor performance of Macrobiotus hufelandi (Tardigrada: Macrobiotidae) were investigated. The tardigrades were collected from Nanwutai, Qinling Mountains which traverse from west to east in central China. The subjects were acclimated to either 2℃ or 22℃ for 2 weeks. The animal was transferred onto a frosted slide and allowed to walk freely at the performance temperature (PT) 2℃ or 22℃. Only one individual was tested per test bout, which lasted from three to five minutes. To avoid occurrence of thermal acclimation effect, the standard adaptation time was limited to 1.5 min. Each subject was tested for once at the same PT, and was tested only at one PT. A total of 25 individuals were tested and measured at the same PT. The locomotor performance of the animals was recorded with a digital video camera mounted on a microscope at 4×10 amplification and replayed on a PC. Every subject was identified. Walking speed (WS) and percentage of time moving (PTM) at both PTs (2℃ or 22℃) were selected as the rate parameters of locomotor performance. The two-way repeated measures ANOVA with a significance level of α= 0.05 and Duncan multiple range test were used to analyze the data. WS of the animals acclimated to and tested at the same temperatures was significantly faster than that for animals acclimated to and tested at the different temperatures, similarly, PTM of the animals acclimated to 22℃ and tested at 22℃ was significantly greater than PTM of animals acclimated to 22℃ and tested at 2℃, which indicated that the animals acclimated to a particular temperature have enhanced locomotor performance in that temperature relative to the animals acclimated to that temperature in other thermal environment. WS of the animals acclimated to 22℃ and tested at 22℃ was significantly faster than WS of animals acclimated to 2℃ and tested at 22℃, PTM of the animals acclimated to 22℃ and tested at 22℃ was significantly greater than PTM of animals acclimated to 2℃ and tested at 22℃. These results supported the BAH. It could be concluded that the PT and thermal acclimation as well as the interaction between the PT and AT significantly influence the locomotor performance of M.hufelandi, and that, despite the existence of a few results of this study that don’t support the BAH, some results of this study support for this hypothesis, and that the animals acclimated to a particular temperature have enhanced locomotor performance in that temperature relative to the animals acclimated to that temperature in other thermal environment, implying that any performance temperature that deviates from the acclimation temperature could cause the reduction of the walking speed which is closely related to the fitness of the M.hufelandi.

New Regularization Algorithms for Solving the Deconvolution Problem in Well Test Data Interpretation

Two new regularization algorithms for solving the first-kind Volterra integral equation, which describes the pressure-rate deconvolution problem in well test data interpretation, are developed in this paper. The main features of the problem are the strong nonuniform scale of the solution and large errors (up to 15%) in the input data. In both algorithms, the solution is represented as decomposition on special basic functions, which satisfy given a priori information on solution, and this idea allow us significantly to improve the quality of approximate solution and simplify solving the minimization problem. The theoretical details of the algorithms, as well as the results of numerical experiments for proving robustness of the algorithms, are presented.

Silymarin in non alcoholic fatty liver disease

AIM: This study was undertaken to evaluate the hepatic effects of silybum marianum on non alcoholic fatty liver disease (NAFLD). METHODS: In 72 patients affected by NAFLD, main metabolic, hepatic and anti-inflammatory parameters were assayed after 3 mo of a restricted diet and before silymarin treatment (twice a day orally). The brightness of liver echography texture (hepatorenal ratio brightness) was also defined at same time. These evaluations were repeated after 6 mo of treatment. RESULTS: Serum levels of some metabolic and anti-inflammatory data nonsignificantly lowered after 6 mo of silymarin. On the contrary, Steato test, alanine aminotransferase (ALT), aspartate aminotransferase (AST) and gamma-glutamyl transpeptidase were significantly (P < 0.001) reduced. Instead, the AST/ALT ratio unchanged. Finally, the hepatorenal brightness ratio, as an index of hepatic steatosis, significantly (P < 0.05) dropped. CONCLUSION: The obtained results indicate that silymarin appears to be effective to reduce the biochemical, inflammatory and ultrasonic indices of hepatic steatosis. Some parameters indicative of early stage of atherosclerosis were also lowered.

Effectiveness of Co-Testing in Cervical Cancer Screening Program in Macao SAR

Background: Cervical cancer remains a significant public health concern in Macao SAR despite the implementation of a cervical cancer screening program and HPV vaccination. To improve early detection, Macao SAR introduced HPV DNA testing alongside cytology (co-testing) as the primary screening method in 2019. This study evaluates the effectiveness of co-testing in identifying cervical precancerous lesions (CIN2+) compared to cytology alone. Methods: We conducted a retrospective analysis of women aged 30 - 65 years who participated in the routine cervical cancer screening program in Macao SAR Primary Healthcare Centers from 2019 to 2022. Data from over 70,000 women were analyzed, comparing the detection rates of CIN2+ through co-testing and cytology alone. Women with abnormal cytology or positive HPV results were referred for colposcopy. Results: The introduction of co-testing led to a significant increase in the detection of CIN2+, particularly in women with atypical squamous cells of undetermined significance (ASCUS) or negative for intraepithelial lesion or malignancy (NILM) cytology results. Between 2019 and 2022, the percentage of women with ASCUS/NILM and any high-risk HPV (hrHPV) positive who were diagnosed with CIN2+ after colposcopy were 24%, 13%, 10% and 7.5% respectively. This highlights the ability of co-testing to identify high-risk individuals who would have been missed by cytology alone. Discussion: Our findings demonstrate the effectiveness of co-testing in improving the sensitivity of cervical cancer screening in Macao SAR. The inclusion of HPV DNA testing allows for better risk stratification of women with ASCUS/NILM cytology, leading to more targeted referrals for colposcopy and timely detection of precancerous lesions. The initial high positive rate in 2019 (24%) might be attributed to the small sample size and potentially reflects a backlog of undiagnosed cases prior to co-testing implementation. Conclusion: The implementation of co-testing in Macao SAR’s cervical cancer screening program significantly improves the early detection of precancerous lesions, particularly in women with ambiguous cytology results. This proactive approach contributes to reducing cervical cancer morbidity and mortality and improving women’s health outcomes in Macao SAR.

Progress and Development Direction of “Three-High” Oil and Gas Well Testing Technology

By reviewing the development of “three-high” oil and gas well testing technology of Sinopec in recent years, this paper systematically summarizes the application of “three-high” oil and gas well testing technology of Sinopec in engineering optimization design technology, and high temperature and high pressure testing technology, high pressure and high temperature transformation completion integration technology. Major progress has been made in seven aspects: plug removal and re-production technology of production wells in high acid gas fields;wellbore preparation technology of ultra-deep, high-pressure, and high-temperature oil and gas wells;surface metering technology;and supporting tool development technology. This paper comprehensively analyzes the challenges faced by the “three-high” oil and gas well production testing technology in four aspects: downhole tools, production testing technology, safe production testing, and the development of low-cost production test tools. Four development directions are put forward: 1) Improve ultra-deep oil and gas testing technology and strengthen integrated geological engineering research. 2) Deepen oil and gas well integrity evaluation technology to ensure the life cycle of oil and gas wells. 3) Carry out high-end, customized, and intelligent research on oil test tools to promote the low-cost and efficient development of ultra deep reservoirs. 4) Promote the fully automatic control of the surface metering process to realize the safe development of “three-high” reservoirs.

Fracture network types revealed by well test curves for shale reservoirs in the Sichuan Basin,China

Pressure buildup testing can be used to analyze fracture network characteristics and conduct quantitative interpretation of relevant parameters for shale gas wells,thus providing bases for assessing the well productivity and formulating proper development strategies.This study establishes a new well test interpretation model for fractured horizontal wells based on seepage mechanisms of shale reservoirs and proposes a method for identifying fracturing patterns based on the characteristic slopes of pressure buildup curves and curve combination patterns.The pressure buildup curve patterns are identified to represent three types of shale reservoirs in the Sichuan Basin,namely the moderately deep shale reservoirs with high pressure,deep shale reservoirs with ultra-high pressure,and moderately deep shale reservoirs with normal pressure.Based on this,the relationship between the typical pressure buildup curve patterns and the fracture network types are put forward.Fracturing effects of three types of shale gas reservoir are compared and analyzed.The results show that typical flow patterns of shale reservoirs include bilinear flow in primary and secondary fractures,linear flow in secondary fractures,bilinear flow in secondary fractures and matrix,and linear flow in matrix.The fracture network characteristics can be determined using the characteristic slopes of pressure buildup curves and curve combinations.The linear flow in early secondary fractures is increasingly distinct with an increase in primary fracture conductivity.Moreover,the bilinear flow in secondary fractures and matrix and the subsequent linear flow in the matrix occur as the propping and density of secondary fractures increase.The increase in the burial depth,in-situ stress,and stress difference corresponds to a decrease in the propping of primary fractures that expand along different directions in the shale gas wells in the Sichuan Basin.Four pressure buildup curve patterns exist in the Sichuan Basin and its periphery.The pattern of pressure buildup curves of shale reservoirs in the Yongchuan area can be described as 1/2/→1/4,indicating limited stimulated reservoir volume,poorly propped secondary fractures,and the forming of primary fractures that extend only to certain directions.The pressure buildup curves of shale reservoirs in the main block of the Fuling area show a pattern of 1/4/→1/2 or 1/2,indicating greater stimulated reservoir volume,well propped secondary fractures,and the forming of complex fracture networks.The pattern of pressure buildup curves of shale reservoirs in the Pingqiao area is 1/2/→1/4→/1/2,indicating a fracturing effect somewhere between that of the Fuling and Yongchuan areas.For reservoirs with normal pressure,it is difficult to determine fracture network characteristics from pressure buildup curves due to insufficient formation energy and limited liquid drainage.

Fast and Accurate Identification of <i>M. tuberculosis</i>Complex Using an Immunochromatographic MPT64 Antigen Detection Test

Background: A new rapid Immunochromatographic test (ICT) kit (MPT64 TB Ag Kit) for detection of MPT64 Antigen in M. tuberculosis (MTB) isolates used for rapid identification of MTB isolates developed by SD (Standard Diagnostics) Bio line, South Korea was evaluated. The ICT is a rapid, reliable and cheaper method that can be used instead of conventional biochemical tests for confirming MTB in culture isolates in resource limited laboratories. The study also evaluated the ability of ICT to detect MPT64-Antigen before the micro MGIT could signal positive. Material/Methods: A total of 450 sputum samples of individual patients were used for the study. 152 isolates of Mycobacteria were recovered from solid and liquid media. These strains were tested for the detection of MPT64-antigen. H37Rv strain was served as the positive reference control and also used for early detection of Antigen experiment. Findings: The development of bands on both test and sample region when H37Rv strain was tested were seen (MPT64 antigen positive). When 138 MTB isolates were tested, it showed a similar banding pattern indicating 100% sensitivity. MPT64 band formation was not detected in any of the 14 isolates indicating 100% specificity. Both PPV & NPV were 100%. All the isolates negative for MPT64 Ag were confirmed as MOTT by conventional bio-chemical PNBA. The H37Rv strain showed a faint band from the 2nd day onwards from inoculation till 3rd day in the earlier Antigen detection experiment. Conclusion: Rapid identification of MTB culture isolate is a pressing need for diagnosis and proceeding to perform drug susceptibility testing. MPT64 TB Ag detection ICT kit is a rapid, reliable method, good substitute for molecular identification methods, and conventional biochemical test which is time-consuming and technically demanding. The early detection of Antigen can be used as an effective tool in diagnosis.

Genetic testing vs microforceps biopsy in pancreatic cysts:Systematic review and meta-analysis

BACKGROUND Carcinoembryonic antigen(CEA)and cytology in pancreatic cystic fluid are suboptimal for evaluation of pancreatic cystic neoplasms.Genetic testing and microforceps biopsy are promising tools for pre-operative diagnostic improvement but comparative performance of both methods is unknown.AIM To compare the accuracy of genetic testing and microforceps biopsy in pancreatic cysts referred for surgery.METHODS We performed a literature search in Medline,Scopus,and Web of Science for studies evaluating genetic testing of cystic fluid and microforceps biopsy of pancreatic cysts,with endoscopic ultrasound with fine-needle aspiration(EUSFNA)prior to surgery and surgical pathology as reference standard for diagnosis.We evaluated the diagnostic accuracy for:1-benign cysts;2-mucinous low-risk cysts;3-high-risk cysts,and the diagnostic yield and rate of correctly identified cysts with microforceps biopsy and molecular analysis.We also assessed publication bias,heterogeneity,and study quality.RESULTS Eight studies,including 1206 patients,of which 203(17%)referred for surgery who met the inclusion criteria were analyzed in the systematic review,and seven studies were included in the meta-analysis.Genetic testing and microforceps biopsies were identical for diagnosis of benign cysts.Molecular analysis was superior for diagnosis of both low and high-risk mucinous cysts,with sensitivities of 0.89(95%CI:0.79-0.95)and 0.57(95%CI:0.42-0.71),specificities of 0.88(95%CI:0.75-0.95)and 0.88(95%CI:0.80-0.93)and AUC of 0.9555 and 0.92,respectively.The diagnostic yield was higher in microforceps biopsies than in genetic analysis(0.73 vs 0.54,respectively)but the rates of correctly identified cysts were identical(0.73 with 95%CI:0.62-0.82 vs 0.71 with 95%CI:0.49-0.86,respectively).CONCLUSION Genetic testing and microforceps biopsies are useful second tests,with identical results in benign pancreatic cysts.Genetic analysis performs better for low-and high-risk cysts but has lower diagnostic yield.

Relationship Between Gene-Phenotype and Clinical Manifestations of Chromosomal Copy Number Variations Indicated by Non-Invasive Prenatal Testing

Objective:To analyze the clinical value of non-invasive prenatal testing(NIPT)in detecting chromosomal copy number variations(CNVs)and to explore the relationship between gene expression and clinical manifestations of chromosomal copy number variations.Methods:3551 naturally conceived singleton pregnant women who underwent NIPT were included in this study.The NIPT revealed abnormalities other than sex chromosome abnormalities and trisomy 13,18,and 21.Pregnant women with chromosome copy number variations underwent genetic counseling and prenatal ultrasound examination.Interventional prenatal diagnosis and chromosome microarray analysis(CMA)were performed.The clinical phenotypes and pregnancy outcomes of different prenatal diagnoses were analyzed.Additionally,a follow-up was conducted by telephone to track fetal development after birth,at six months,and one year post-birth.Results:A total of 53 cases among 3551 cases showed chromosomal copy number variation.Interventional prenatal diagnosis was performed in 36 cases:27 cases were negative and 8 were consistent with the NIPT test results.This indicates that NIPT’s positive predictive value(PPV)in CNVs is 22.22%.Conclusion:NIPT has certain clinical significance in screening chromosome copy number variations and is expected to become a routine screening for chromosomal microdeletions and microduplications.However,further interventional prenatal diagnosis is still needed to identify fetal CNVs.

Field testing of shear strength of granite residual soils

The characteristics of residual soils are very different from those of sedimentary soils.Although the strength characteristics of sedimentary soils have been studied extensively,the shear strength characteristics of granitic residual soils(GRS)subjected to the weathering of parent rocks have rarely been investigated.In this study,the shear strength characteristics of GRS in the Taishan area of southeast China(TSGRS)were studied by field and laboratory tests.The field tests consisted of a cone penetration test(CPT),borehole shear test(BST),self-boring pressuremeter test(SBPT),and seismic dilatometer Marchetti test(SDMT).The shortcomings of laboratory testing are obvious,with potential disturbances arising through the sampling,transportation,and preparation of soil samples.Due to the special structure of GRS samples and the ease of disturbance,the results obtained from laboratory tests were generally lower than those obtained from situ tests.The CPT and scanning electron microscopy(SEM)results indicated significant weathering and crustal hardening in the shallow TSGRS.This resulted in significant differences in the strength and strength parameters of shallow soil obtained by the BST.Based on the SDMT and SBPT results,a comprehensive evaluation method of shear strength for TSGRS was proposed.The SBPT was suitable for evaluating the strength of shallow GRS.The material index(ID)and horizontal stress index(KD)values obtained by the SDMT satisfied the empirical relationship proposed by Marchetti based on the ID index,and were therefore considered suitable for the evaluation of the shear strength of deep GRS.

Reasons resulting in the collapsed tubing near wellhead in high pressure and high temperature deep well during well testing and measures to prevent the collapsing

Because various reasons, the tubing near wellhead was collapsed during well testing in high pressure and high temperature deep well when the outer pressure was less than collapsing strength. To find the reasons in the abnormally collapse and countermeasures, first the quality of the tubing was checked. It was founded that the collapse was not resulted from the defect of the tubing. Then, force and stress exerted in the tubing was analyzed taking XS2 well as an example. The analysis results were concluded as follows. The collapsing strength of tubing decreased due to the axial tensile, which is seriously at the upper tubing especially. During injecting, the additional axial force that was caused by the temperature effect increased the tubing near wellhead to suffer axial tensile and further reduced the collapsing strength of tubing near wellhead. Reinforcing defect, prohibiting defect tubing to trip in hole, according to the calculation to impose appropriate annular pressure, selecting size nozzle to reverse pumping and controlling the reverse pumping speed and pressure, prohibiting to be opened flow and reducing or releasing the annular pressure can prevent the well testing tubing down-hole being collapsed at the wellhead.

Assessing the Spatial Equality of COVID Testing Sites Maintaining Zero COVID Policy

Rapid and timely testing is essential to minimize the COVID-19 spread. Decision makers and policy planners need to determine the equal distribution and accessibility of testing sites. This study mainly examines the spatial equality of COVID-19 testing sites that maintain a zero COVID policy in Guangzhou City. The study has identified the spatial disparities of COVID testing sites, characteristics of testing locations, and accessibility. The study has obtained information on COVID testing sites in Guangzhou City and population data. Point pattern analyses, Euclidian distance and allocation, and network analyses are the main methods used to achieve the research objectives, and 1183 total COVID testing sites can be recognized in Guangzhou City. Results revealed that spatial disparities could be noticed over the study area. Testing locations of Guangzhou City are highly clustered. The most significant testing sites are located in Haizhu District, which has the third largest population. The highest population density can be identified in Yuexiu District. However, only 94 testing sites are located there. According to all the results, higher disparities can be identified, and a lack of testing sites is located in the north part of the study area. Some people in the northern part have to travel more than 10 km to reach a testing site. Finally, this paper suggests increasing the number of testing sites in the north and south parts of the study area and keeping the same distribution, considering the area, total population, and population density. This kind of research will be helpful to decision-makers in making proper decisions to maintain a zero COVID policy.

Behavioral Characteristics of Pharmacologically Selected Lines of Rats: Relevance to Depression

This brief review discusses the behavioral consequences of two pharmacologically selected lines of rats. Flinders Sensitive (FSL) and Flinders Resistant (FRL) Lines of rats were selected on the basis of differential hypothermic and behavioral responses to the anticholinesterase, diisopropylfluorophosphate (DFP). FSL rats are more sensitive to the hypothermic effects of cholinergic, serotonergic, and dopaminergic agonists but less sensitive to the locomotor or stereotypic effects of dopamine agonists. FSL rats exhibit greater immobility in the forced swim test and reduced social interaction compared with FRL rats, but do not differ in saccharin intake, behavior in the elevated plus maze, or responses for rewarding brain self-stimulation. The exaggerated immobility and reduced social interaction are counteracted by chronic treatment with antidepressants. Because FSL rats were more sensitive to 5-HT1A receptor agonists, high (HDS) and low (LDS) 8-OH-DPATsensitive lines were selectively bred for differential hypothermic responses to the 5-HT1A receptor agonist, 8-hydroxy-2-(di-N-propylamino)tetralin (8-OH-DPAT). HDS rats were also more sensitive to the hypothermic effects of oxotremorine, a cholinergic agonist, but selection for this response did not diverge with later selection. HDS rats exhibited greater immobility in the forced swim test than LDS rats and this correlated response could be seen early in selection (generation 3). HDS rats also showed reduced social interaction compared to LDS rats, but did not differ in behavior in the elevated plus maze. These findings confirm that selection for hypothermic responses to pharmacological agents do have behavioral consequences, notably the production of depressive-like phenotypes, which can be counteracted by chronic antidepressant treatment. Because increased 5-HT1A receptor sensitivity was common to both selected lines (FSL and HDS), neurobiological processes dependent on this receptor could contribute to the abnormal behaviors that manifest in these rat lines and thus suggesting a mechanism underlying depressive behaviors in humans. However, available human data are inconsistent with this hypothesis and suggest that other mechanisms underlie these behavioral abnormalities in HDS and FSL rats. These mechanisms as well as additional behavioral testing in these rat lines will be discussed.

Optimality of Group Testing with Differential Misclassification

Group testing is a method that can be used to estimate the prevalence of rare infectious diseases,which can effectively save time and reduce costs compared to the method of random sampling.However,previous literature only demonstrated the optimality of group testing strategy while estimating prevalence under some strong assumptions.This article weakens the assumption of misclassification rate in the previous literature,considers the misclassification rate of the infected samples as a differentiable function of the pool size,and explores some optimal properties of group testing for estimating prevalence in the presence of differential misclassification conforming to this assumption.This article theoretically demonstrates that the group testing strategy performs better than the sample by sample procedure in estimating disease prevalence when the total number of sample pools is given or the size of the test population is determined.Numerical simulation experiments were conducted to evaluate the performance of group tests in estimating prevalence in the presence of dilution effect.