Development of a high-repetition-rate lumped-inductance kicker magnet prototype for the beam switchyard of SHINE

The Shanghai high-repetition-rate X-ray free-electron laser and extreme light facility(SHINE)operates at a maximum repetition rate of 1 MHz.Kicker magnets are key components that distribute electron bunches into three different undulator lines in a bunch-by-bunch mode.The kicker field width must be less than the time interval between bunches.A lumpedinductance kicker prototype was developed using a vacuum chamber with a single-turn coil.The full magnetic field strength was 0.005 T.This paper presents the requirements,design considerations,design parameters,magnetic field calculations,and measurements of the kicker magnets.The relevant experimental results are also presented.The pulse width of the magnetic field was approximately 600 ns,and the maximum operation repetition rate was 1 MHz.The developed kicker satisfies the requirements for the SHINE project.Finally,numerous recommendations for the future optimization of kicker magnets are provided.

The second fusion of laser and aerospace-an inspiration for high energy lasers

Since the first laser was invented,the pursuit of high-energy lasers(HELs)has always been enthusiastic.The first revolution of HELs was pushed by the fusion of laser and aerospace in the 1960s,with the chemical rocket engines giving fresh impetus to the birth of gas flow and chemical lasers,which finally turned megawatt lasers from dream into reality.Nowadays,the development of HELs has entered the age of electricity as well as the rocket engines.The properties of current electric rocket engines are highly consistent with HELs’goals,including electrical driving,effective heat dissipation,little medium consumption and extremely light weight and size,which inspired a second fusion of laser and aerospace and motivated the exploration for potential HELs.As an exploratory attempt,a new configuration of diode pumped metastable rare gas laser was demonstrated,with the gain generator resembling an electric rocket-engine for improved power scaling ability.

Transmission effects of high energy nanosecond lasers in laser-induced air plasma under different pressures

When a high energy nanosecond(ns)laser induces breakdown in the air,the plasma density generated in the rarefied atmosphere is much smaller than that at normal pressure.It is associated with a relatively lower absorption coefficient and reduces energy loss of the laser beam at low pressure.In this paper,the general transmission characterizations of a Joule level 10 ns 1064 nm focused laser beam are investigated both theoretically and experimentally under different pressures.The evolution of the electron density(n_(e)),the changes in electron temperature(T_(e))and the variation of laser intensity(I)are employed for numerical analyses in the simulation model.For experiments,four optical image transfer systems with focal length(f)of 200 mm are placed in a chamber and employed to focus the laser beam and produce plasmas at the focus.The results suggest that the transmittance increases obviously with the decreasing pressure and the plasma channels on the transmission path can be observed by the self-illumination.The simulation results agree well with the experimental data.The numerical model presents that the maximum n_e at the focus can reach 10^(19)cm^(-3),which is far below the critical density(n_(c)).As a result,the laser beam is not completely shielded by the plasmas.

High-energy-density electron beam generation in ultra intense laser-plasma interaction

By using a two-dimensional particle-in-cell simulation,we demonstrate a scheme for highenergy-density electron beam generation by irradiating an ultra intense laser pulse onto an aluminum（Al） target.With the laser having a peak intensity of 4×10^23W cm^-2,a high quality electron beam with a maximum density of 117 nc and a kinetic energy density up to8.79×10^18J m^-3 is generated.The temperature of the electron beam can be 416 Me V,and the beam divergence is only 7.25°.As the laser peak intensity increases（e.g.,1024 W cm^-2）,both the beam energy density（3.56×10^19J m^-3） and the temperature（545 Me V） are increased,and the beam collimation is well controlled.The maximum density of the electron beam can even reach 180 nc.Such beams should have potential applications in the areas of antiparticle generation,laboratory astrophysics,etc.

Superior corrosion resistance-dependent laser energy density in(CoCrFeNi)95Nb5 high entropy alloy coating fabricated by laser cladding

(CoCrFeNi)95Nb5 high entropy alloy(HEA)coatings were successfully fabricated on a substrate of Q235 steel by laser cladding technology.These(CoCrFeNi)95Nb5 HEA coatings possess excellent properties,particularly corrosion resistance,which is clearly superior to that of some typical bulk HEA and common engineering alloys.In order to obtain appropriate laser cladding preparation process parameters,the effects of laser energy density on the microstructure,microhardness,and corrosion resistance of(CoCrFeNi)95Nb5 HEA coating were closely studied.Results showed that as the laser energy density increases,precipitation of the Laves phase in(CoCrFeNi)95Nb5 HEA coating gradually decreases,and diffusion of the Fe element in the substrate intensifies,affecting the integrity of the(CoCrFeNi)95Nb5 HEA.This decreases the microhardness of(CoCrFeNi)95Nb5 HEA coatings.Moreover,the relative content of Cr2O3,Cr(OH)3,and Nb2O5 in the surface passive film of the coating decreases with increasing energy density,causing corrosion resistance to decrease.This study demonstrates the controllability of a high-performance HEA coating using laser cladding technology,which has significance for the laser cladding preparation of other CoCrFeNi-system HEA coatings.

High Heat Flux Testing of B_4C/Cu and SiC/Cu Functionally Graded Materials Simulated by Laser and Electron Beam

B4C, SiC and C, Cu functionally graded-materials (FGMs) have been developed by plasma spraying and hot pressing. Their high-heat flux properties have been investigated by high energy laser and electron beam for the simulation of plasma disruption process of the future fusion reactors, And a study on eroded products of B4C/Cu FGM under transient thermal load of electron beam was performed. In the experiment, SEM and EDS analysis indicated that B4C and SiC were decomposed, carbon was preferentially evaporated under high thermal load, and a part of Si and Cu were melted, in addition, the splash of melted metal and the particle emission of brittle destruction were also found. Different erosive behaviors of carbon-based materials (CBMs) caused by laser and electron beam were also discussed.

Research on Irradiation Electric Field for Charged Particles Beam with High Energy

Irradiation protection of the nonlinear optical devices used in the spacecraft and next generation active laser system must be solved. The first problem was to find the irradiation damage mechanism of the nonlinear materials. In this paper the irradiation electronic field originating from high speed charged particle beams was discussed. The calculating model of the electronic field, based on the relativistic mechanics and electro-magnetic theory, was founded. The common characters of the irradiation electronic field were predicted and the fields of α ray and β ray were calculated by means of our model. The simulating results showed that the intensity of the electric field increased with the energy or the intensity of the beam. The results also showed that the field change trend of α ray and β ray was similar, but the field value was quite different. When the beam intensity I = 100 μA and the beam energy εm = 500 Mev, the electronic field values were about 3.5 × 107 v/m for α ray and 2.4 × 1011 v/m for β ray.

Phase transition model of water flow irradiated by high-energy laser in a chamber

In the absorption chamber of a high-energy laser energy meter, water is directly used as an absorbing medium and the interaction of the high-power laser and the water flow can produce a variety of physical phenomena such as phase transitions. The unit difference method is adopted to deduce the phase transition model for water flow irradiated by a high-energy laser. In addition, the model is simulated and verified through experiments. Among them, the experimental verification uses the photographic method, shooting the distribution and the form of the air mass of water flow in different operating conditions, which are compared with the simulation results. The research shows that it is achievable to reduce the intensity of the phase transition by increasing the water flow, reducing the power intensity of the beam, shortening the distance the beam covers, reducing the initial water temperature or adopting a shorter wavelength laser. The study＇s results will provide the reference for the design of a water-direct-absorption-type high-energy laser energy meter as well as an analysis of the interaction processes of other similar high-power lasers and water flow.

Comparison of Calculated Fit and Experimental Calculations of Average Dose Deposited in Aluminum by High Energy Electron Beams

This paper presents the formalism for absorbed dose determination to Aluminum in high-energy electron beams using Rhodotron accelerator. Depth dose curve for Aluminum at electron energy of 10 MeV was calculated. The calculated curve in the model as a function of the depth is compared to the experimental. The agreement of the final results remained well within the expected acceptable range. The calculated values of dose-to-Aluminum are completely fit with the measured values in the range of 0.07% for electron energy of 10 MeV.

Generating Proton Beams Exceeding 10 MeV Using High Contrast 60TW Laser

A prototype of a laser driven proton accelerator is built at Peking University. Protons exceeding IOMeV are accelerated from micrometer-thick aluminum targets irradiated by tightly focused laser pulse with 1.8 J energy and 30fs duration. The beam energy spectrum and charge distribution are measured by a Thomson parabola spectrometer and radiochromic fihn stacks. The sensitivity of proton cut-off energy to the focusing of the laser beam, the pulse duration, and the foil thickness are systematically investigated in the experiments. Stable proton beams have been produced with an optimized parameter set, providing a cornerstone for the future applications of laser accelerated protons.

High-flux electron beams from laser wakefield accelerators driven by petawatt lasers

Laser wakefield accelerators （LWFAs） are considered to be one of the most compeuuve next- generation accelerator candidates. In this paper, we will study the potential high-flux electron beam production of an LWFA driven by petawatt-level laser pulses. In our three-dimensional particle-in-cell simulations, an optimal set of parameters gives -40 nC of charge with 2 PW laser power, thus -400 kA of instantaneous current if we assume the electron beam duration is 100 fs. This high flux and its secondary radiation are widely applicable in nuclear and QED physics, industrial imaging, medical and biological studies.

Generation of high-energy dual-wavelength domain wall pulse with low repetition rate in an HNLF-based fiber ring laser

The generation of high-energy dual-wavelength domain wall pulse with a low repetition rate is demonstrated in a highly nonlinear fiber （HNLF）-based fiber ring laser. By introducing the intracavity birefringence-induced spectral filtering effect, the dual-wavelength lasing operation can be achieved. In order to enhance the cross coupling effect between the two lasing beams for domain wall pulse formation, a 215-m HNLF is incorporated into the laser cavity. Experimentally, it is found that the dual-wavelength domain wall pulse with a repetition rate of 77.67 kHz could be efficiently obtained through simply rotating the polarization controller （PC）. At a maximum pump power of 322 mW, the 655-nJ single pulse energy in cavity is obtained. The proposed configuration provides a simpler and more efficient way to generate high energy pulse with a low repetition rate.

A 37 mJ,100 Hz,high energy single frequency oscillator

Ways on energy enhancement for single frequency oscillator are reported in this paper.By quantitative analysis on gain and loss coefficients for each cavity mode with inserted etalons,a 37 mJ,100 Hz high energy single-frequency Nd:YAG oscillator is obtained.The pulse energy is promoted by enhancement of nearly 7 times for a single frequency oscillator reported.The result proves that this method does help for energy enhancement.It has attractive potential for high energy single frequency oscillator design,especially on condition of intensive side pumped or long cavity laser,where strong competitors exist and are hard to be suppressed.

HIGH ENERGY Xe^+ ENHANCED ADHESION OF Al AND Ag FILMS ON OPTICAL GLASS

The samples consisting of 100nm Al or Ag film on optical glass substrate were irradiated by a beam of Xe 5×1015 to 2×1016 cm-2 with energy 320 keV. The adhesion of films on substrates was tested by Xe+ irradiation. Optical character was measured by spectrophotometer. The ion mixing amount was measured by RBS. The results showed that after ion irradiating the adhesion of the film on the glass is enhanced. The adherent strength is greater than 10 kg/cm2. The thermal stability of the films is good. The irradiated film is more optically efficient, the surface is smooth and rendered more corrosion resistance. The mechanism of the film adhesion was discussed.

Effect of thickness on the microstructure of GaN films on Al_2 O_3 (0001) by laser molecular beam epitaxy

Heteroepitaxial GaN films are grown on sapphire （0001） substrates using laser molecular beam epitaxy. The growth processes are in-situ monitored by reflection high energy electron diffraction. It is revealed that the growth mode of GaN transformed from three-dimensional （3D） island mode to two-dimensional （2D） layer-by-layer mode with the increase of thickness. This paper investigates the interfacial strain relaxation of GaN films by analysing their diffraction patterns. Calculation shows that the strain is completely relaxed when the thickness reaches 15 nm. The surface morphology evolution indicates that island merging and reduction of the island-edge barrier provide an effective way to make GaN films follow a 2D layer-by-layer growth mode. The ll0-nm GaN films with a 2D growth mode have smooth regular hexagonal shapes. The X-ray diffraction indicates that thickness has a significant effect on the crystallized quality of GaN thin films.

High power semiconductor laser array with single-mode emission

The semiconductor laser array with single-mode emission is presented in this paper.The 6-μm-wide ridge waveguides(RWGs)are fabricated to select the lateral mode.Thus the fundamental mode of laser array can be obtained by the RWGs.And the maximum output power of single-mode emission can reach 36 W at an injection current of 43 A,after that,a kink will appear.The slow axis(SA)far-field divergence angle of the unit is 13.65.The beam quality factor M;of the units determined by the second-order moment(SOM)method,is 1.2.This single-mode emission laser array can be used for laser processing.

Enhancement of proton collimation and acceleration by an ultra-intense laser interacting with a cone target followed by a beam collimator

A special method is proposed of a laser-induced cavity pressure acceleration scheme for collimating,accelerating and guiding protons,using a single-cone target with a beam collimator through a target normal sheath acceleration mechanism.In addition,the problems involved are studied by using two-dimensional particle-in-cell simulations.The results show that the proton beam can be collimated,accelerated and guided effectively through this type of target.Theoretically,a formula is derived for the combined electric field of accelerating protons.Compared with a proton beam without a beam collimator,the proton beam density and cut-off energy of protons in the type II are increased by 3.3 times and 10%respectively.Detailed analysis shows that the enhancement is mainly due to the compact and strong sheath electrostatic field,and that the beam collimator plays a role in focusing energy.In addition,the simulation results show that the divergence angle of the proton beam in type II is less than 1.67 times that of type I.The more prominent point is that the proton number of type II is 2.2 times higher than that of type I.This kind of target has important applications in many fields,such as fast ion ignition in inertial fusion,high energy physics and proton therapy.

Improvement of Beam Energy Measurement System for BES-III

The beam energy measurement system is significant and profit for both BES-III detector and BEPC-II accelerator. The detection of the high energy scattering photons is realized by virtue of the Compton backscattering principle. Many advanced techniques and precise instruments are employed to acquire the highly accurate measurement of positron/electron beam energy. During five years’ running period, in order to satisfy the requirement of data taking and enhance the capacity of measurement itself, the upgradation of system is continued, which involves the components reformation of laser and optics subsystem, replacement of view-port of the laser to vacuum insertion subsystem, the usage of electric cooling system for high purity germanium detector, and the refinement of data acquisition and processing subsystem. The upgrading of system guarantees the smooth and effective measuring of beam energy at BEPC-II and accommodates the accurate offline energy values for further physics analysis at BES-III.

Fuel compression in the magnetized cylindrical implosion driven by a gold tube heated by heavy ion beams

A magnetized cylindrical target composed of a gold tube filled with deuterium-tritium fuel plasma at low density is studied numerically in the present paper.A shock wave is produced when a heavy ion beam heats the gold along the direction of the magnetic field.The density peak of the shock wave increases with the increase in time and it propagates in the-r direction in the cylindrical tube.It seems that this wave is the supermagnetosonic wave.It is found that the Mach number M is between 6.96 and 19.19.The density peak of the shock wave increases as the intensity of the heavy ion beam increases.Furthermore,the density peak of the shock wave increases as the external magnetic field increases.

Wind Velocity Measurement of Multi-Laser Beams Measurement System Based on Peak Delay Technique

Contactless measurement of wind flow has been utilized in many fields, such as weather forecasting, hurricane tracking, and aeronautic alarm. In this paper, a novel multi-laser beams measuring system （MLBM） for high precision detection of wind field based on optical scintillations and small perturbation theory was proposed and verified. According to the fluctuation intensity of laser backscatter received by two detectors, peak delay technique was adopted to determine the velocity of wind flow. Detailed procedure to deal with backscatter signals was also presented. Then, practical experiments and measurement results showed high precision of the proposed system for wind measurement with a relative error as 3.21%. Consequently, the MLBM system possesses obvious potential application in engineering project.