A biochar-supported green nZVI(G-nZVI@MKB)composite was synthesized using mango kernel waste with“dual identity”as reductant and biomass of biochar.The G-nZVI@MKB with a Fe/C mass ratio of 2.0(G-nZVI@MKB2)was determ...A biochar-supported green nZVI(G-nZVI@MKB)composite was synthesized using mango kernel waste with“dual identity”as reductant and biomass of biochar.The G-nZVI@MKB with a Fe/C mass ratio of 2.0(G-nZVI@MKB2)was determined as the most favorable composite for hexavalent chromium(Cr(VI))removal.Distinct influencing parameters were discussed,and 99.0%of Cr(VI)removal occurred within 360 min under these optimized parameters.Pseudo-second order kinetic model and intra-particle diffusion model well depicted Cr(VI)removal process.The XRD,FTIR,SEM,and XPS analyses verified the key roles of G-nZVI and functional groups,as well as the primary removal mechanisms involving electrostatic attraction,reduction,and complexation.G-nZVI@MKB2 exhibited good stability and reusability with only a 16.4%decline in Cr(VI)removal after five cycles.This study offered evidence that mango kernel could be recycled as a beneficial resource to synthesize green nZVI-loaded biochar composite for efficient Cr(VI)elimination from water.展开更多
Up to 1.5wt%of Cr(Ⅲ)salts(CrCl_(3),and Cr_(2)O_(3))and Cr(Ⅵ)salts(Na_(2)CrO_(4),and CaCr_(2)O_(7))were incorporated into red mud-based geopolymers,respectively.The solidification/stabilization,compressive strength,a...Up to 1.5wt%of Cr(Ⅲ)salts(CrCl_(3),and Cr_(2)O_(3))and Cr(Ⅵ)salts(Na_(2)CrO_(4),and CaCr_(2)O_(7))were incorporated into red mud-based geopolymers,respectively.The solidification/stabilization,compressive strength,and durability of the Cr-containing geopolymers were investigated.The experimental results indicate that the red mud-based geopolymer could effectively solidify/stabilize different types of Cr salts with solidification/stabilization rates of above 99.61%.Geopolymers are environmentally safe when the dosage of CaCr_(2)O_(7)is≤1.0wt%,or the dosage of CrCl_(3),Cr_(2)O_(3),and Na_(2)CrO_(4)is≤1.5wt%,respectively.The effects of Cr salts on the compressive strength varies with the type and content of Cr salts.The freeze-thaw cycle is more destructive to geopolymer properties than sulfate attack or acid rain erosion.The solidification/stabilization of Cr is mainly attributed to the following reasons:a)The chemical binding of Cr is related to the formation of Cr-containing hydrates(eg,magnesiochromite((Mg,Fe)(Cr,Al)_(2)O_(4)))and doping into N-A-S-H gel and C-A-S-H gel framework;b)The physical effect is related to the encapsulation by the hydration products(e g,N-A-S-H gel and C-A-S-H gel).This study provides a reference for the treatment of hazardous Cr-containing wastes by solid waste-based geopolymers.展开更多
In order to address the issue that the photocatalytic reduction of hexavalent chromium(Cr(VI))is often limited by the inefficient utilization of electrons in photocatalysts,a quasi-MOF photocatalyst using thiocyanate(...In order to address the issue that the photocatalytic reduction of hexavalent chromium(Cr(VI))is often limited by the inefficient utilization of electrons in photocatalysts,a quasi-MOF photocatalyst using thiocyanate(-SCN)was developed as a modulator to enhance the charge transfer properties of ZIF-L-based photocatalysts.The incorporation of-SCN introduced structural defects,which improved visible light absorption and the reduction ability of photogenerated electrons.-SCN significantly adjusted the electronic properties and established a stable electron release pathway,serving as active sites for reduction.The optimized quasi-MOF demonstrated a Cr(VI)reduction rate of 94.8%in neutral potassium thiocyanate solution under visible light without a hole scavenger.The reaction rate constant is 2.8 times that of the photocatalyst without defect modulation.This study offers a promising strategy for developing highly efficient photocatalysts for environmental remediation.展开更多
A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling t...A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling tower blow-down, plating, electroplating, rinse water sources, anodizing baths etc. are the main sources of Cr (VI) contamination. The Cr (VI) is not only non-biodegradable in the environment but also carcinogenic to living population. It is still difficult to treat Cr contaminated waste water effectively, safely, eco-friendly, and economically. As a result, many techniques have been used to treat Cr (VI)-polluted wastewater, including adsorption, chemical precipitation, coagulation, ion-exchange, and filtration. Among these practices, the most practical method is adsorption for the removal of Cr (VI) from aqueous solutions, which has gained widespread acceptance due to the ease of use and affordability of the equipment and adsorbent. It has been revealed that Fe-based adsorbents’ oxides and hydroxides have high adsorptive potential to lower Cr (VI) content below the advised threshold. Fe-based adsorbents were also discovered to be relatively cheap and toxic-free in Cr (VI) treatment. Fe-based adsorbents are commonly utilized in industry. It has been discovered that nanoparticles of Fe-, Ti-, and Cu-based adsorbents have a better capacity to remove Cr (VI). Cr (VI) was effectively removed from contaminated water using mixed element-based adsorbents (Fe-Mn, Fe-Ti, Fe-Cu, Fe-Zr, Fe-Cu-Y, Fe-Mg, etc.). Initial findings suggest that Cr (VI) removal from wastewater may be accomplished by using magnesium ferrite nanomaterials as an efficient adsorbent.展开更多
Phosphorus fertilizers from less pure sedimentary sources become increasingly important, due to depletion of phosphorus from igneous rock of high quality. Consequently, robust methods with potential to remove various ...Phosphorus fertilizers from less pure sedimentary sources become increasingly important, due to depletion of phosphorus from igneous rock of high quality. Consequently, robust methods with potential to remove various types of hazardous elements are required. Among such impurities, hexavalent chromium (Cr(VI)) is very likely to become a future challenge. Different industrial ways to treat phosphate rock are currently being practised, and we have here studied how chromium behaves when using the nitro-phosphate process. The reduction mechanism of Cr (VI) in nitric acid and phosphoric acid solutions was investigated by measuring redox potential and UV-VIS spectra. The results show that Cr (VI) is not stable in strong nitric acid solutions. Reduction of Cr (VI) species decreased with decreasing temperature, NO<sub>2</sub> concentration, ionic strength and absence of light. These findings support the proposed reduction reaction:The reduction rate was observed proportional to the nitric acid decomposition: .展开更多
Metal trace elements (MTE) are among the most harmful micropollutants of natural waters. Eliminating them helps improve the quality and safety of drinking water and protect human health. In this work, we used mango ke...Metal trace elements (MTE) are among the most harmful micropollutants of natural waters. Eliminating them helps improve the quality and safety of drinking water and protect human health. In this work, we used mango kernel powder (MKP) as bioadsorbent material for removal of Cr (VI) from water. Uv-visible spectroscopy was used to monitor and quantify Cr (VI) during processing using the Beer-Lambert formula. Some parameters such as pH, mango powder, mass and contact time were optimized to determine adsorption capacity and chromium removal rate. Adsorption kinetics, equilibrium, isotherms and thermodynamic parameters such as ΔG˚, ΔH˚, and ΔS˚, as well as FTIR were studied to better understand the Cr (VI) removal process by MKP. The adsorption capacity reached 94.87 mg/g, for an optimal contact time of 30 min at 298 K. The obtained results are in accordance with a pseudo-second order Freundlich adsorption isotherm model. Finally FTIR was used to monitor the evolution of absorption bands, while Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) were used to evaluate surface properties and morphology of the adsorbent.展开更多
Study was carried out to analyze the distribution and migration patterns,soil-to-plant transfer and potential health risks of chromium in soil-vegetable system in areas near a ferro-alloy manufactory in Hunan province...Study was carried out to analyze the distribution and migration patterns,soil-to-plant transfer and potential health risks of chromium in soil-vegetable system in areas near a ferro-alloy manufactory in Hunan province.The results show that soils near sewer outlet,sewer channel and in control area are averaged 2 239.5,995.33 and 104.9 mg/kg,respectively.The total Cr has a relative accumulation in soil depth of 200-400 mm near the sewer outlet,mainly enriches in the surface layer(0-200 mm) near the sewer channel and decreases gradually in unpolluted soils.The differential concentration level of enrichment between layers is little.The results also indicate that the three vegetables of celery,lettuce and Chinese cabbage are able to convert the potentially toxic Cr(Ⅵ) species into the non-toxic Cr(Ⅲ) species,and the chromium contents in the edible parts of the vegetables are averaged 11.95 mg/kg.The transfer factors of the three vegetables follow the order:Chinese cabbage lettuce celery.The estimated total daily intake of chromium substantially exceeds the dietary allowable value,which may pose health risks to local population.展开更多
The reduction behaviors of FeO·V2O3 and FeO·Cr2O3 during coal-based direct reduction have a decisive impact on the efficient utilization of high-chromium vanadium-bearing titanomagnetite concentrates. The ef...The reduction behaviors of FeO·V2O3 and FeO·Cr2O3 during coal-based direct reduction have a decisive impact on the efficient utilization of high-chromium vanadium-bearing titanomagnetite concentrates. The effects of molar ratio of C to Fe n(C)/n(Fe) and temperature on the behaviors of vanadium and chromium during direct reduction and magnetic separation were investigated. The reduced samples were characterized by X-ray diffraction(XRD), scanning election microscopy(SEM) and energy dispersive spectrometry(EDS) techniques. Experimental results indicate that the recoveries of vanadium and chromium rapidly increase from 10.0% and 9.6% to 45.3% and 74.3%, respectively, as the n(C)/n(Fe) increases from 0.8 to 1.4. At n(C)/n(Fe) of 0.8, the recoveries of vanadium and chromium are always lower than 10.0% in the whole temperature range of 1100-1250 °C. However, at n(C)/n(Fe) of 1.2, the recoveries of vanadium and chromium considerably increase from 17.8% and 33.8% to 42.4% and 76.0%, respectively, as the temperature increases from 1100 °C to 1250 °C. At n(C)/n(Fe) lower than 0.8, most of the FeO·V2O3 and FeO·Cr2O3 are not reduced to carbides because of the lack of carbonaceous reductants, and the temperature has little effect on the reduction behaviors of FeO·V2O3 and FeO·Cr2O3, resulting in very low recoveries of vanadium and chromium during magnetic separation. However, at higher n(C)/n(Fe), the reduction rates of FeO·V2O3 and FeO·Cr2O3 increase significatly because of the excess amount of carbonaceous reductants. Moreover, higher temperatures largely induce the reduction of FeO·V2O3 and FeO·Cr2O3 to carbides. The newly formed carbides are then dissolved in the γ(FCC) phase, and recovered accompanied with the metallic iron during magnetic separation.展开更多
[Objective] The aim was to develop a rapid, simple method for determination of chromium and zinc in soil samples by flame atomic absorption spectrometry.[Method] The method for determination of Cr and Zn in soil by co...[Objective] The aim was to develop a rapid, simple method for determination of chromium and zinc in soil samples by flame atomic absorption spectrometry.[Method] The method for determination of Cr and Zn in soil by combined flame atomic absorption spectrometry and microwave digestion was used. [Result] The concentration curve was linear within the range of 0-0.8 mg/L for Cr and 0-0.8 mg/L for Zn, the detection limits of Cr and Zn was 0.0025 mg/L and 0.002 3 mg/L, respectively. Recoveries of 102.4%-103.2% for Cr and 97.7%-98.3% for Zn were obtained for there soil samples. [Conclusion] The proposed method has the advantages of simple operation, high sensitivity, and high efficiency; it was successfully used for determination of Cr and Zn in soil samples.展开更多
[Objective] To optimize the techniques for culturing Cr-enriched Dendrobi-um candidum protocorm. [Method] By adopting Plackett-Burman test, the effects of time, temperature, Cr-content in medium, NAA content, KT conte...[Objective] To optimize the techniques for culturing Cr-enriched Dendrobi-um candidum protocorm. [Method] By adopting Plackett-Burman test, the effects of time, temperature, Cr-content in medium, NAA content, KT content and light intensi-ty on Cr-enriched protocorm were researched. Three factors of time, Cr-content in medium and light intensity had statistical y significant effects; then steepest ascent procedures were applied to define optimal response region of these three factors; fi-nal y the optimal factors were determined by RSM analysis. [Result] The results showed that the optimal conditions for Cr-enrichment were chromium concentration at 0.37 mg/L, culture time of 59 d and il umination intensity of 1 822.22 lx. The predicted value of Cr-content in protocorm was 5.08 mg/kg. [Conclusion] RSM can optimize the techniques for culturing Cr-enriched protocorm of Dendrobium can-didum, provide the optimum process parameters and lay the foundation for further research.展开更多
The extraction experiments of chromium(W) from aqueous waste solution by predispersed solvent extraction (PDSE) process with extractant (HEHPEHE) and its mixture, including acidic extractant (D2EHPA), alkaline...The extraction experiments of chromium(W) from aqueous waste solution by predispersed solvent extraction (PDSE) process with extractant (HEHPEHE) and its mixture, including acidic extractant (D2EHPA), alkaline extractant (TOA) and neutral extractant (TBP) were carried out respectively. It is found that the extractant HEHPEHE exhibited high extraction selectivity to chromium(III) from aqueous waste solution. The colloidal liquid aphrons (CLAs) were successfully generated using kerosene as a solvent, HEHPEHE as an extractant, sodium dodecyl benzene sulphate (SDBS) as a surfactant in aqueous phase and polyoxyethylene sorbitol anhydride monolaurate (Tween-20) in oil phase. To study the extraction efficiency and advantages of the PDSE process in the removal of chromium(III), the effects of major factors, such as initial chromium(III) concentration, volume of colloidal gas aphrons (CGAs), HEHPEHE volume fraction, phase ratio (solvent phase to water phase), mass fraction of dodecyl trimethylammonium bromide (HTAB), mass fraction of SDBS, mass fraction of Tween-20 and initial pH of aqueous waste solution were also investigated and the appropriate process conditions were obtained. Under the appropriate conditions, the extraction efficiency of chromium(III) above 99.9 % can be achieved and the treated aqueous waste solution can be discharged directly without polluting the environment.展开更多
The electro-reduction of chromium oxide(Cr2O3) was investigated in an equimolar mixture of CaCl2-NaCl molten salt at 800℃ for developing a more efficient process for chromium preparation. Cyclic voltammetry and pot...The electro-reduction of chromium oxide(Cr2O3) was investigated in an equimolar mixture of CaCl2-NaCl molten salt at 800℃ for developing a more efficient process for chromium preparation. Cyclic voltammetry and potentiostatic electrolysis were used to study the electro-reduction of the Cr2O3-loaded metallic cavity electrode. In addition, a number of parameters affecting the rate and extent of Cr2O3 electrolysis were considered to better understand the electrolysis process. The results demonstrate that CaCl2-NaCl molten salt is applicable for preparing Cr directly from Cr2O3 and the electrolysis parameters exert great influence on the cathode product. Under optimal experimental conditions, nodular Cr with an oxygen content of 0.5%(mass fraction) was obtained without any chromium carbides detected by XRD. Furthermore, the relatively high solubility of CaO and quite rapid crystal growth result in the formation of large platelet CaCr2O4, and the addition of NaCl to CaCl2 results in several variations on the electrolysis process and the product morphology from pure CaCl2 molten salt.展开更多
The impact of chromium(Ⅲ) and (Ⅵ) forms on soil catalase activity was presented. The Orthic Podzol, Haplic Phaeozem and Mollic Gleysol from different depths were used in the experiment. The soil samples were ame...The impact of chromium(Ⅲ) and (Ⅵ) forms on soil catalase activity was presented. The Orthic Podzol, Haplic Phaeozem and Mollic Gleysol from different depths were used in the experiment. The soil samples were amended with solution of Cr(Ⅲ) using CrCl3, and with Cr(Ⅵ) using K2Cr2O7 in the concentration range from 0 to 20 mg/kg, whereas the samples without the addition of chromium served as control. Catalase activity was assayed by one of the commonly used spectrophotometric methods. As it was demonstrated in the experiment, both Cr(Ⅲ) and Cr(Ⅵ) have an ability to reduce soil catalase activity. A chromium dosage of 20 mg/kg caused the inhibition of catalase activity and the corresponding contamination levels ranged from 75% to 92% for Cr(Ⅲ) and 68% to 76% for Cr(Ⅵ), with relation to the control. Catalase activity reached maximum in the soil material from surface layers (0-25 cm), typically characterized by the highest content of organic matter creating favorable conditions for microorganisms.展开更多
The toxic effects of rare earth elements such as lanthanum, cerium and heavy metal elements such as chromium, zinc on Potamogeton malaianus Miq. were studied. The results show that the contents of chlorophyll and solu...The toxic effects of rare earth elements such as lanthanum, cerium and heavy metal elements such as chromium, zinc on Potamogeton malaianus Miq. were studied. The results show that the contents of chlorophyll and soluble protein increase to a certain degree and then decrease under La3+ Ce3+ Zn2+ stress, while there is a constantly dropping tendency under Cr6+ stress. The four ions have different effects on protective enzyme systems of Potamogeton malaianus. They can induce rises of the activities of catalase (CAT) and peroxides (POD) at lower concentration, however, with the increase of ions concentration, the activities decline. The change of SOD activity is exactly opposite to that of CAT and POD activity. It falls at first and rises later. An increasing tendency of MDA content appears with the increasing concentration. The toxicities of La3+, Zn2+, Ce3+ and Cr6+ become more serious in the order. The lethal concentration of Cr6+ to Potamogeton malaianus ranges from 0.5 to I mg(-1) that of Ce3+ and Zn2+ ranges from 3 to 5 mg(-1) and that of La3+ ranges from 7 to 10 mg(.)L(-1). The toxic mechanism of La3 + and Ce3+ is similar to that of Cr6+ and Zn2+.展开更多
The oxidation induration and reduction swelling behavior of chromium-bearing vanadium titanomagnetite pellets(CVTP)with Cr2O3 addition were studied,and the reduction swelling index(RSI)and compressive strength(CS)of t...The oxidation induration and reduction swelling behavior of chromium-bearing vanadium titanomagnetite pellets(CVTP)with Cr2O3 addition were studied,and the reduction swelling index(RSI)and compressive strength(CS)of the reduced CVTP with simulated coke oven gas(COG)injection were investigated.The results showed that the CS of the CVTP decreases and the porosity of the CVTP increases with increasing amount of Cr2O3 added.The Cr2O3 mainly exists in the form of(Cr,Fe)2O3 solid solution in the CVTP and as Fe-Cr in the reduced CVTP.The CS of the reduced CVTP increases and the RSI of the reduced CVTP decreases with increasing amount of Cr2O3 added.The limited aggregation and diffusion of metallic iron contribute to the formation of dense lamellar crystals,which leads to the slight decrease for reduction swelling behavior of reduced CVTP.This work provides a theoretical and technical basis for the utilization of CVTP and other Cr-bearing ores such as chromite with COG recycling technology.展开更多
基金supported by the National Natural Science Foundation of China(51808253)the Science and Technology Planning Project of Jilin Province(20220508008RC)+1 种基金Science and Technology Project of Jilin Provincial Education Department(JJKH20220295KJ and JJKH20210272KJ)the Science and Technology Projects of the Ministry of Housing and Urban-Rural Development(2018-K6-003).
文摘A biochar-supported green nZVI(G-nZVI@MKB)composite was synthesized using mango kernel waste with“dual identity”as reductant and biomass of biochar.The G-nZVI@MKB with a Fe/C mass ratio of 2.0(G-nZVI@MKB2)was determined as the most favorable composite for hexavalent chromium(Cr(VI))removal.Distinct influencing parameters were discussed,and 99.0%of Cr(VI)removal occurred within 360 min under these optimized parameters.Pseudo-second order kinetic model and intra-particle diffusion model well depicted Cr(VI)removal process.The XRD,FTIR,SEM,and XPS analyses verified the key roles of G-nZVI and functional groups,as well as the primary removal mechanisms involving electrostatic attraction,reduction,and complexation.G-nZVI@MKB2 exhibited good stability and reusability with only a 16.4%decline in Cr(VI)removal after five cycles.This study offered evidence that mango kernel could be recycled as a beneficial resource to synthesize green nZVI-loaded biochar composite for efficient Cr(VI)elimination from water.
基金Funded by the National Natural Science Foundation of China(Nos.52074245,52374416 and 52202029)the China Postdoctoral Science Foundation(No.2022M721058)。
文摘Up to 1.5wt%of Cr(Ⅲ)salts(CrCl_(3),and Cr_(2)O_(3))and Cr(Ⅵ)salts(Na_(2)CrO_(4),and CaCr_(2)O_(7))were incorporated into red mud-based geopolymers,respectively.The solidification/stabilization,compressive strength,and durability of the Cr-containing geopolymers were investigated.The experimental results indicate that the red mud-based geopolymer could effectively solidify/stabilize different types of Cr salts with solidification/stabilization rates of above 99.61%.Geopolymers are environmentally safe when the dosage of CaCr_(2)O_(7)is≤1.0wt%,or the dosage of CrCl_(3),Cr_(2)O_(3),and Na_(2)CrO_(4)is≤1.5wt%,respectively.The effects of Cr salts on the compressive strength varies with the type and content of Cr salts.The freeze-thaw cycle is more destructive to geopolymer properties than sulfate attack or acid rain erosion.The solidification/stabilization of Cr is mainly attributed to the following reasons:a)The chemical binding of Cr is related to the formation of Cr-containing hydrates(eg,magnesiochromite((Mg,Fe)(Cr,Al)_(2)O_(4)))and doping into N-A-S-H gel and C-A-S-H gel framework;b)The physical effect is related to the encapsulation by the hydration products(e g,N-A-S-H gel and C-A-S-H gel).This study provides a reference for the treatment of hazardous Cr-containing wastes by solid waste-based geopolymers.
基金supported by the Open Project of Yunnan Precious Metals Laboratory Co.,Ltd.,China (Nos.YPML-2023050264,YPML-2023050204)the Natural Science Foundation of Hunan Province,China (No.2022JJ40613)+4 种基金the National Natural Science Foundation of China (No.12074435)the Science and Technology Innovation Program of Hunan Province,China (No.2021RC4001)the Science and Technology Planning Project of Yunnan Province,China (No.202302AH360001)China Postdoctoral Science Foundation (No.2023M743941)the Postdoctoral Fellowship Program (Grade B)of China Postdoctoral Science Foundation (No.GZB20240858)。
文摘In order to address the issue that the photocatalytic reduction of hexavalent chromium(Cr(VI))is often limited by the inefficient utilization of electrons in photocatalysts,a quasi-MOF photocatalyst using thiocyanate(-SCN)was developed as a modulator to enhance the charge transfer properties of ZIF-L-based photocatalysts.The incorporation of-SCN introduced structural defects,which improved visible light absorption and the reduction ability of photogenerated electrons.-SCN significantly adjusted the electronic properties and established a stable electron release pathway,serving as active sites for reduction.The optimized quasi-MOF demonstrated a Cr(VI)reduction rate of 94.8%in neutral potassium thiocyanate solution under visible light without a hole scavenger.The reaction rate constant is 2.8 times that of the photocatalyst without defect modulation.This study offers a promising strategy for developing highly efficient photocatalysts for environmental remediation.
文摘A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling tower blow-down, plating, electroplating, rinse water sources, anodizing baths etc. are the main sources of Cr (VI) contamination. The Cr (VI) is not only non-biodegradable in the environment but also carcinogenic to living population. It is still difficult to treat Cr contaminated waste water effectively, safely, eco-friendly, and economically. As a result, many techniques have been used to treat Cr (VI)-polluted wastewater, including adsorption, chemical precipitation, coagulation, ion-exchange, and filtration. Among these practices, the most practical method is adsorption for the removal of Cr (VI) from aqueous solutions, which has gained widespread acceptance due to the ease of use and affordability of the equipment and adsorbent. It has been revealed that Fe-based adsorbents’ oxides and hydroxides have high adsorptive potential to lower Cr (VI) content below the advised threshold. Fe-based adsorbents were also discovered to be relatively cheap and toxic-free in Cr (VI) treatment. Fe-based adsorbents are commonly utilized in industry. It has been discovered that nanoparticles of Fe-, Ti-, and Cu-based adsorbents have a better capacity to remove Cr (VI). Cr (VI) was effectively removed from contaminated water using mixed element-based adsorbents (Fe-Mn, Fe-Ti, Fe-Cu, Fe-Zr, Fe-Cu-Y, Fe-Mg, etc.). Initial findings suggest that Cr (VI) removal from wastewater may be accomplished by using magnesium ferrite nanomaterials as an efficient adsorbent.
文摘Phosphorus fertilizers from less pure sedimentary sources become increasingly important, due to depletion of phosphorus from igneous rock of high quality. Consequently, robust methods with potential to remove various types of hazardous elements are required. Among such impurities, hexavalent chromium (Cr(VI)) is very likely to become a future challenge. Different industrial ways to treat phosphate rock are currently being practised, and we have here studied how chromium behaves when using the nitro-phosphate process. The reduction mechanism of Cr (VI) in nitric acid and phosphoric acid solutions was investigated by measuring redox potential and UV-VIS spectra. The results show that Cr (VI) is not stable in strong nitric acid solutions. Reduction of Cr (VI) species decreased with decreasing temperature, NO<sub>2</sub> concentration, ionic strength and absence of light. These findings support the proposed reduction reaction:The reduction rate was observed proportional to the nitric acid decomposition: .
文摘Metal trace elements (MTE) are among the most harmful micropollutants of natural waters. Eliminating them helps improve the quality and safety of drinking water and protect human health. In this work, we used mango kernel powder (MKP) as bioadsorbent material for removal of Cr (VI) from water. Uv-visible spectroscopy was used to monitor and quantify Cr (VI) during processing using the Beer-Lambert formula. Some parameters such as pH, mango powder, mass and contact time were optimized to determine adsorption capacity and chromium removal rate. Adsorption kinetics, equilibrium, isotherms and thermodynamic parameters such as ΔG˚, ΔH˚, and ΔS˚, as well as FTIR were studied to better understand the Cr (VI) removal process by MKP. The adsorption capacity reached 94.87 mg/g, for an optimal contact time of 30 min at 298 K. The obtained results are in accordance with a pseudo-second order Freundlich adsorption isotherm model. Finally FTIR was used to monitor the evolution of absorption bands, while Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) were used to evaluate surface properties and morphology of the adsorbent.
基金Project (2009ZX07212-001-01) supported by the Key Project of National Natural Science Foundation for Water Pollution Control and RemediationProject (50925417) supported by the National Funds for Distinguished Young Scientists+1 种基金Project (50830301) supported by the National Natural Science Foundation of ChinaProject (51074191) supported by the National Natural Science Foundation of China
文摘Study was carried out to analyze the distribution and migration patterns,soil-to-plant transfer and potential health risks of chromium in soil-vegetable system in areas near a ferro-alloy manufactory in Hunan province.The results show that soils near sewer outlet,sewer channel and in control area are averaged 2 239.5,995.33 and 104.9 mg/kg,respectively.The total Cr has a relative accumulation in soil depth of 200-400 mm near the sewer outlet,mainly enriches in the surface layer(0-200 mm) near the sewer channel and decreases gradually in unpolluted soils.The differential concentration level of enrichment between layers is little.The results also indicate that the three vegetables of celery,lettuce and Chinese cabbage are able to convert the potentially toxic Cr(Ⅵ) species into the non-toxic Cr(Ⅲ) species,and the chromium contents in the edible parts of the vegetables are averaged 11.95 mg/kg.The transfer factors of the three vegetables follow the order:Chinese cabbage lettuce celery.The estimated total daily intake of chromium substantially exceeds the dietary allowable value,which may pose health risks to local population.
基金Projects(2013CB632601,2013CB632604)supported by the National Basic Research Program of ChinaProject(51125018)supported by the National Science Foundation for Distinguished Young Scholars of China+1 种基金Project(KGZD-EW-201-2)supported by the Key Research Program of the Chinese Academy of SciencesProjects(51374191,21106167,51104139)supported by the National Natural Science Foundation of China
文摘The reduction behaviors of FeO·V2O3 and FeO·Cr2O3 during coal-based direct reduction have a decisive impact on the efficient utilization of high-chromium vanadium-bearing titanomagnetite concentrates. The effects of molar ratio of C to Fe n(C)/n(Fe) and temperature on the behaviors of vanadium and chromium during direct reduction and magnetic separation were investigated. The reduced samples were characterized by X-ray diffraction(XRD), scanning election microscopy(SEM) and energy dispersive spectrometry(EDS) techniques. Experimental results indicate that the recoveries of vanadium and chromium rapidly increase from 10.0% and 9.6% to 45.3% and 74.3%, respectively, as the n(C)/n(Fe) increases from 0.8 to 1.4. At n(C)/n(Fe) of 0.8, the recoveries of vanadium and chromium are always lower than 10.0% in the whole temperature range of 1100-1250 °C. However, at n(C)/n(Fe) of 1.2, the recoveries of vanadium and chromium considerably increase from 17.8% and 33.8% to 42.4% and 76.0%, respectively, as the temperature increases from 1100 °C to 1250 °C. At n(C)/n(Fe) lower than 0.8, most of the FeO·V2O3 and FeO·Cr2O3 are not reduced to carbides because of the lack of carbonaceous reductants, and the temperature has little effect on the reduction behaviors of FeO·V2O3 and FeO·Cr2O3, resulting in very low recoveries of vanadium and chromium during magnetic separation. However, at higher n(C)/n(Fe), the reduction rates of FeO·V2O3 and FeO·Cr2O3 increase significatly because of the excess amount of carbonaceous reductants. Moreover, higher temperatures largely induce the reduction of FeO·V2O3 and FeO·Cr2O3 to carbides. The newly formed carbides are then dissolved in the γ(FCC) phase, and recovered accompanied with the metallic iron during magnetic separation.
基金Supported by Key Fund of Guangxi Academy of Agricultural Sciences(2014JZ01 and2013YZ07)~~
文摘[Objective] The aim was to develop a rapid, simple method for determination of chromium and zinc in soil samples by flame atomic absorption spectrometry.[Method] The method for determination of Cr and Zn in soil by combined flame atomic absorption spectrometry and microwave digestion was used. [Result] The concentration curve was linear within the range of 0-0.8 mg/L for Cr and 0-0.8 mg/L for Zn, the detection limits of Cr and Zn was 0.0025 mg/L and 0.002 3 mg/L, respectively. Recoveries of 102.4%-103.2% for Cr and 97.7%-98.3% for Zn were obtained for there soil samples. [Conclusion] The proposed method has the advantages of simple operation, high sensitivity, and high efficiency; it was successfully used for determination of Cr and Zn in soil samples.
文摘[Objective] To optimize the techniques for culturing Cr-enriched Dendrobi-um candidum protocorm. [Method] By adopting Plackett-Burman test, the effects of time, temperature, Cr-content in medium, NAA content, KT content and light intensi-ty on Cr-enriched protocorm were researched. Three factors of time, Cr-content in medium and light intensity had statistical y significant effects; then steepest ascent procedures were applied to define optimal response region of these three factors; fi-nal y the optimal factors were determined by RSM analysis. [Result] The results showed that the optimal conditions for Cr-enrichment were chromium concentration at 0.37 mg/L, culture time of 59 d and il umination intensity of 1 822.22 lx. The predicted value of Cr-content in protocorm was 5.08 mg/kg. [Conclusion] RSM can optimize the techniques for culturing Cr-enriched protocorm of Dendrobium can-didum, provide the optimum process parameters and lay the foundation for further research.
基金Project (NCET-07-0577) supported by New Century Excellent Talents of Ministry of Education, China
文摘The extraction experiments of chromium(W) from aqueous waste solution by predispersed solvent extraction (PDSE) process with extractant (HEHPEHE) and its mixture, including acidic extractant (D2EHPA), alkaline extractant (TOA) and neutral extractant (TBP) were carried out respectively. It is found that the extractant HEHPEHE exhibited high extraction selectivity to chromium(III) from aqueous waste solution. The colloidal liquid aphrons (CLAs) were successfully generated using kerosene as a solvent, HEHPEHE as an extractant, sodium dodecyl benzene sulphate (SDBS) as a surfactant in aqueous phase and polyoxyethylene sorbitol anhydride monolaurate (Tween-20) in oil phase. To study the extraction efficiency and advantages of the PDSE process in the removal of chromium(III), the effects of major factors, such as initial chromium(III) concentration, volume of colloidal gas aphrons (CGAs), HEHPEHE volume fraction, phase ratio (solvent phase to water phase), mass fraction of dodecyl trimethylammonium bromide (HTAB), mass fraction of SDBS, mass fraction of Tween-20 and initial pH of aqueous waste solution were also investigated and the appropriate process conditions were obtained. Under the appropriate conditions, the extraction efficiency of chromium(III) above 99.9 % can be achieved and the treated aqueous waste solution can be discharged directly without polluting the environment.
基金Project(2013CB632600)supported by the National Basic Research Program of ChinaProjects(21376251,21406233)supported by the National Natural Science Foundation of ChinaProject supported by the Fund of Hubei Zhenhua Chemical Co.,Ltd.,China
文摘The electro-reduction of chromium oxide(Cr2O3) was investigated in an equimolar mixture of CaCl2-NaCl molten salt at 800℃ for developing a more efficient process for chromium preparation. Cyclic voltammetry and potentiostatic electrolysis were used to study the electro-reduction of the Cr2O3-loaded metallic cavity electrode. In addition, a number of parameters affecting the rate and extent of Cr2O3 electrolysis were considered to better understand the electrolysis process. The results demonstrate that CaCl2-NaCl molten salt is applicable for preparing Cr directly from Cr2O3 and the electrolysis parameters exert great influence on the cathode product. Under optimal experimental conditions, nodular Cr with an oxygen content of 0.5%(mass fraction) was obtained without any chromium carbides detected by XRD. Furthermore, the relatively high solubility of CaO and quite rapid crystal growth result in the formation of large platelet CaCr2O4, and the addition of NaCl to CaCl2 results in several variations on the electrolysis process and the product morphology from pure CaCl2 molten salt.
文摘The impact of chromium(Ⅲ) and (Ⅵ) forms on soil catalase activity was presented. The Orthic Podzol, Haplic Phaeozem and Mollic Gleysol from different depths were used in the experiment. The soil samples were amended with solution of Cr(Ⅲ) using CrCl3, and with Cr(Ⅵ) using K2Cr2O7 in the concentration range from 0 to 20 mg/kg, whereas the samples without the addition of chromium served as control. Catalase activity was assayed by one of the commonly used spectrophotometric methods. As it was demonstrated in the experiment, both Cr(Ⅲ) and Cr(Ⅵ) have an ability to reduce soil catalase activity. A chromium dosage of 20 mg/kg caused the inhibition of catalase activity and the corresponding contamination levels ranged from 75% to 92% for Cr(Ⅲ) and 68% to 76% for Cr(Ⅵ), with relation to the control. Catalase activity reached maximum in the soil material from surface layers (0-25 cm), typically characterized by the highest content of organic matter creating favorable conditions for microorganisms.
文摘The toxic effects of rare earth elements such as lanthanum, cerium and heavy metal elements such as chromium, zinc on Potamogeton malaianus Miq. were studied. The results show that the contents of chlorophyll and soluble protein increase to a certain degree and then decrease under La3+ Ce3+ Zn2+ stress, while there is a constantly dropping tendency under Cr6+ stress. The four ions have different effects on protective enzyme systems of Potamogeton malaianus. They can induce rises of the activities of catalase (CAT) and peroxides (POD) at lower concentration, however, with the increase of ions concentration, the activities decline. The change of SOD activity is exactly opposite to that of CAT and POD activity. It falls at first and rises later. An increasing tendency of MDA content appears with the increasing concentration. The toxicities of La3+, Zn2+, Ce3+ and Cr6+ become more serious in the order. The lethal concentration of Cr6+ to Potamogeton malaianus ranges from 0.5 to I mg(-1) that of Ce3+ and Zn2+ ranges from 3 to 5 mg(-1) and that of La3+ ranges from 7 to 10 mg(.)L(-1). The toxic mechanism of La3 + and Ce3+ is similar to that of Cr6+ and Zn2+.
基金financially supported by the National Natural Science Foundation of China (Nos.51674084, 51174051, and 51574082)
文摘The oxidation induration and reduction swelling behavior of chromium-bearing vanadium titanomagnetite pellets(CVTP)with Cr2O3 addition were studied,and the reduction swelling index(RSI)and compressive strength(CS)of the reduced CVTP with simulated coke oven gas(COG)injection were investigated.The results showed that the CS of the CVTP decreases and the porosity of the CVTP increases with increasing amount of Cr2O3 added.The Cr2O3 mainly exists in the form of(Cr,Fe)2O3 solid solution in the CVTP and as Fe-Cr in the reduced CVTP.The CS of the reduced CVTP increases and the RSI of the reduced CVTP decreases with increasing amount of Cr2O3 added.The limited aggregation and diffusion of metallic iron contribute to the formation of dense lamellar crystals,which leads to the slight decrease for reduction swelling behavior of reduced CVTP.This work provides a theoretical and technical basis for the utilization of CVTP and other Cr-bearing ores such as chromite with COG recycling technology.