Fabrication and flexural strength of porous Si3N4 ceramics with Li2CO3 and Y2O3 as sintering additives

By employing sintering additives of Li2CO3 and Y2O3,porous Si3N4 ceramics are prepared after experiencing the processes of sintering and post-vacuum heat treatment at 1680 and 1550°C,respectively.The experimental results demonstrate the completed phase transformation fromαtoβ-Si3N4 in Si3N4 ceramic samples with a amount of 1.60 wt%Li2CO3(0.65 wt%Li2O)and 0.33 wt%Y2O3 additives.The as-synthesized porous Si3N4 ceramics exhibit high flexural strength((126.7±2.7)MPa)and high open porosity of 50.4%at elevated temperature(1200°C).These results are attributed to the significant role of added Li2CO3 as sintering additive,where the volatilization of intergranular glassy phase occurs during sintering process.Therefore,porous Si3N4 ceramics with desired mechanical property prepared by altering the addition of sintering additives demonstrate their great potential as a promising candidate for high temperature applications.

Effects of Prestressing of the Ring Gear in Interference Fit on Flexural Fatigue Strength of Tooth Root

When the gearbox body interference is connected to the ring gear, prestressing occurs in the ring gear, which has a significant impact on the strength and life of the gear. Research on the prestressing of the inner ring gear is in the preliminary stage, and the distribution rule of the prestressing and the influence of each parameter on the interference prestressing have not been derived. In this paper, based on the method of calculating the prestressing of the thick cylinder in interference fit, the ring gear is found to be equivalent to a thick cylinder, and the distribution rule of prestressing of the ring gear in the interference fit is inferred. Then, by modeling and analyzing the gearbox body and ring gear in the interference fit using ABAQUS, the distribution rule of prestressing the ring gear in the interference fit is obtained through a numerical simulation. Finally, the prestressing of the ring gear in the interference fit is measured using X-ray di raction, and the distribution rule of prestressing of the ring gear in the interference fit is obtained through analysis. Compared with the distribution rule of prestressing in theory, numerical simulation, and experiment, the theoretical distribution rule of prestressing is amended through a statistical method, and a more accurate formula of prestressing is obtained. Through the calculation of the stress and bending moment in the dangerous section of the ring gear through prestressing, the formula for checking the tooth root flexural fatigue strength in the interference fit prestressing is inferred. This research proposes a tooth root bending strength conditional formula for the inner ring gear of the interference fit, which serves as a guide for the design and production of the actual interference joint inner ring gear.

PREPARATION AND PROPERTIES OF BULK CERAMICS VIA PYROLYSIS OF POLYCARBOSILANE WITH ACTIVE FILLERS II.FLEXURAL STRENGTH AND ANTI-OXIDATIVE PROPERTIES OF ACTIVE FILLER/PCS DERIVED BULK CERAMICS

The flexural strengths and oxidative resistant properties of the ceramics derived from polycarbosilane and active fillers (Ti, TiH 2, TiB 2, Cr, and CrSi 2) were measured and characterized. The introduction of active fillers enhances slightly the flexural strengths, and further densification is required to obtain higher strengths. The oxidative resistant behaviors of the specimens with active fillers are, by means of weight gain in air, poorer compared with those without active fillers.

INFLUENCE OF LOADING RATE AND SPECIMEN HEIGHT ON FLEXURAL STRENGTH OF Al_2O_3 AT HIGH TEMPERATURES

In this paper, the influence of loading rate and specimen height on flexural strength of Al2O3 at high temperatures has been studied by three-point bending method. The experimental results show that the flexural strength of Al2O3 decreases with increasing specimen height at room temperature, and it tends to stability when height increases to a certain degree (h=5mm in this paper), while the flexural strength of Al2O3 variates unapparently at high temperature with increasing height. There is a critical loading rate R . c. When loading rate R . is less than R . c, the flexural strength of Al2O3 increases with increasing loading rate and it drops sharply when loading rate is higher than R . c. The sensitivity of flexural strength to the loading rate decreases with elevating temperatures.

Flexural fatigue strength of steel fibrous concrete containing mixed steel fibres

This paper reports investigation conducted to study the fatigue performance of steel fibre reinforced concrete (SFRC) containing fibres of mixed aspect ratio. An extensive experimental program was conducted in which 90 flexural fatigue tests were carried out at different stress levels on size 500 mm×100 mm×100 mm SFRC specimens respectively containing 1.0%, 1.5% and 2.0% volume fraction of fibres. About 36 static flexural tests were also conducted to determine the static flexural strength prior to fatigue testing. Each volume fraction of fibres incorporated corrugated mixed steel fibres of size 0.6 mm×2.0 mm×25 mm and 0.6 mm×2.0 mm×50 mm in ratio 50:50 by weight. The results are presented both as S-N relationships, with the maximum fatigue stress expressed as a percentage of the strength under static loading, and as relationships between actually applied fatigue stress and number of loading cycles to failure. Two-million-cycle fatigue strengths of SFRC containing different volume fractions of mixed fibres were obtained and compared with plain concrete.

Flexural strength of zirconia/stainless steel functionally graded materials

Zirconia/stainless steel (ZrO2/SUS316L) functionally graded materials (FGMs) were fabricated by tape casting and laminating. Microstructures of FGMs were observed by optical microscope. Fracture behavior of FGMs in different loading modes and influences of different gradient changes on flexural strength were investigated. The results show that ZrO2/ SUS316L FGMs with graded components at interlayers are obtained after they are sintered in vacuum and pressureless condition at 1 350 ℃. TheⅠ?Ⅱ mixed mode crack creates in composite layer and grows to both sides zigzag while loading on ZrO2 layer. Flexural strengths are 496.4,421.7 and 387.5 MPa when gradient changes are 10%,15% and 20%,but flexural strengths of the corresponding fracture layers are 387.1,334.6 and 282.3 MPa since cracks of FGMs are affected by three-dimensional stress,respectively. The cracks are generated in ZrO2 layer and extend to SUS316L layer while loading is added on SUS316L layer,flexural strength does not change with the graded components and keeps consistent basically.

Influence of the column-to-beam flexural strength ratio on the failure mode of beam-column connections in RC frames

The column-to-beam flexural strength ratio(CBFSR)has been used in many seismic codes to achieve the strong column-weak beam(SCWB)failure mode in reinforced concrete(RC)frames,in which plastic hinges appear earlier in beams than in columns.However,seismic investigations show that the required limit of CBFSR in seismic codes usually cannot achieve the SCWB failure mode under strong earthquakes.This study investigates the failure modes of RC frames with different CBFSRs.Nine typical three-story RC frame models with different CBFSRs are designed in accordance with Chinese seismic codes.The seismic responses and failure modes of the frames are investigated through time-history analyses using 100 ground motion records.The results show that the required limit of the CBFSR that guarantees the SCWB failure mode depends on the beam-column connection type and the seismic intensity,and different types of beam-column connections exhibit different failure modes even though they are designed with the same CBFSR.Recommended CBFSRs are proposed for achieving the designed SCWB failure mode for different types of connections in RC frames under different seismic intensities.These results may provide some reference for further revisions of the SCWB design criterion in Chinese seismic codes.

Compressive and Flexural Strengths of Cement Stabilized Earth Bricks Reinforced with Treated and Untreated Pineapple Leaves Fibres

This study compares the effect of treated pineapple leaves fibres (T-PALF) with sodium hydroxide solution and untreated fibres (N-PALF) on the compressive and flexural strength of earth bricks stabilized with 3% and 5% cement. The fibre content ranged from 0% to 5% in steps of 1% by weight. The compressive strength tests were made at 7, 14, 21 and 28 days of curing;the flexural strength test were conducted at 28th day only. The results show that the T-PALF had a higher compressive strength when comparing to the N-PALF. The highest compressive strength of the bricks was obtained at 28 days of curing. The compressive strength at 28 days of stabilized brick at 3% and 5% of cement reinforced with T-PALF were 4.01 and 4.81 MPa, respectively, while the one reinforced with N-PALF was 3.19 and 4.63 MPa, respectively. The results further show that the highest flexural strength of both stabilized bricks at 3% and 5% of cement reinforced with T-PALF and N-PALF was obtained with the bricks stabilized with 5% of cement reinforced with T-PALF. This results show that bricks stabilized with 5% cement and reinforced with 3% of treated fibres content are good for construction of load bearing walls. It was observed;a significant improvement of the reinforced blocks under flexure than under compression.

Effects of Loading Rate on Flexural-tension Properties and Uniaxial Compressive Strength of Micro-surfacing Mixture

The major objective of this research was to discuss the effects of loading rate on the flexural-tension properties and uniaxial compressive strength of micro-surfacing mixture using three-point bending test and uniaxial compressive test respectively. As a preventive maintenance surface treatment on asphalt pavement, micro-surfacing was formed on the basis of the ISSA recommendation of an optimum micro-surfacing design. Tests were conducted over a wide range of temperature to investigate the difference of properties from low loading rate to a relatively high loading rate. Three-point bending test was used to study the flexural strength, strain and modulus of micro-surfacing mixture, and uniaxial compressive test was carried out to obtain the relationship between strength and the loading rate as well as temperature. The experimental results showed that flexural strength at high loading rate was larger than that at low loading rate. The flexural strength difference between low and high loading rate enlarged when the temperature rose. The flexural strain at high loading rate increased compared with results of the low loading rate. Results of the flexural modulus revealed that micro-surfacing mixture exhibited better anti-cracking characteristic at low temperature when given a relatively low loading rate. Results of uniaxial compressive test revealed that the strength difference of micro-surfacing among different loading rates increased with the increase of temperature. The logarithm relationship between the strength and loading rate over a wide range of temperature was obtained to compare the experimental and predicted values, which resulting in a reasonable consistency.

Experimental Study on Flexural Behavior of Post-Tensioning Bonded Partially Prestressed Ultra-High Strength Concrete Beams

This paper presents the results of four partially prestressed ultra-high strength concrete beams in flexure. The test results are used to evaluate the effects of prestressing tendon depth and area on flexure behavior of specimen beams. The test results indicate that: the cracking load,yielding load,peak load and stiffness postcracking of specimen beams are enhanced by reducing prestressing tendon depth or increasing prestressing tendon area, and the flexural ductility is improved by increasing prestressing tendon depth or reducing prestressing tendon area. The effect of complex reinforcement index considering the strength of the equivalence principle and the reinforcement position on loading levels under serviceability limit state,flexural strength and displacement ductility factor are studied. The influence coefficient of prestressing tendon kpis introduced in the complex reinforcement index. As the complex reinforcement index increases, the loading levels under serviceability limit state and flexural strength increases linearly,and the displacement ductility factor decreases linearly. The test results also verify the conventional beam flexural theory based on the plane cross-section assumption for predicting ultimate flexural strength of partially prestressed ultra-high strength concrete beams is valid. After the introduction of the coefficient kp,the calculation method of cracks in code for design of concrete structure in china are appropriated for the specimen beams.

Corrosion effect on the flexural strength &micro-hardness of ips e-max ceramics

Objectives: The effect of ceramics construction (press- able, machinable) and corrosion on flexural strength and micro-hardness was studied. Materials & Methods: Two types of ceramics were tested: IPS e-max Press and IPS e-max CAD. Forty samples were constructed and divided into 2 groups according to the type of ceramics. Each group was then subdivided into 2 subgroups. Subgroups 1 were not subjected to corrosion while subgroups 2 were subjected to corro-sion test. Finally each subgroup was divided into 2 classes according to the type of test: biaxial flexural strength, micro-hardness. Results: There was a sig-nificant difference between the two tested ceramics as regard weight loss as IPS e-max CAD recorded less weight loss than IPS e-max Press. As regard the flex-ural strength, IPS e-max CAD recorded significant higher strength than IPS e-max Press. Corroded sam- ples recorded significant lower flexural strength than non-corroded samples for the two tested ceramics. As regard the Vickers micro-hardness test, the results showed significant difference between the two tested ceramics. IPS e-max CAD recorded higher mi-cro-hardness values than IPS e-max Press. The results also showed that the corroded samples recorded no significant micro-hardness values than non- corroded samples for the two tested ceramics. Conclusions: IPS e-max CAD recorded less weight loss weight loss after being subjected to corrosion test than IPS e-max Press. The method of fabrication affected the flexural strength &micro-hardness of ceramic as machinable ceramic (e-max CAD) recorded significant higher data than pressable ceramic (e-mas Press). Corrosion decreased the flexural strength of both tested ceramics but had no effect on micro- hardness.

Compressive and Flexural Strength of Recycled Reactive Powder Concrete Containing Finely Dispersed Local Wastes

The main objective of this experimental study is to investigate the behavior of Recycled Reactive Powder Concrete (RRPC) developed from finely dispersed local waste raw materials. In this study, RRPC was developed by utilizing local wastes (finely dispersed waste glass powder, waste fly ash and waste ceramic powder) together with Portland cement, fine sand, admixture, steel fibers and water through full replacement of silica fume as well as quartz powder for sustainable construction practice. In this study, all raw materials for making RRPC were analyzed for X-Ray Fluorescence analysis. For sustainability of local construction works, this study employed standard curing method at ambient temperatures instead of steam curing at higher temperatures. Moreover, hand mixing was used throughout the study. To evaluate the structural performances of the developed RRPC mixes, compressive and flexural strengths of RRPC were investigated experimentally and compared with the control mix. The experimental results indicated that replacing the silica fume fully by finely dispersed local waste glass powder (GP) and fly ash (FA) is a promising approach for local structural construction applications. Accordingly, a mean compressive strength of 62.9 MPa and flexural strength of 8.8 MPa were developed using 50% GP-50% FA at 28thdays standard curing. In this study, 17.56% larger compressive strength and 30.6% flexural strength improvements were observed as compared to the control mix.

Effect of Zirconium Oxide Nano-Fillers Addition on the Flexural Strength, Fracture Toughness, and Hardness of Heat-Polymerized Acrylic Resin

Purpose: The mechanical strength of polymethyl methacrylate (PMMA) remains far from ideal for maintaining the longevity of denture. The purpose of this study was to evaluate the effect of Zirconium oxide (ZrO2) nanofillers powder with different concentration (1.5%, 3%, 5% and 7%) on the flexural strength, fracture toughness, and hardness of heat-polymerized acrylic resin. Materials and methods: Zirconium oxide powders with different concentrations (1.5%, 3%, 5% and 7%) were incorporated into heat-cure acrylic resin (PMMA) and processed with optimal condition (2.5:1 Powder/monomer ratio, conventional packing method and water bath curing for 2 hours at 95。C) to fabricate test specimens of PMMA of dimensions (50 × 30 × 30 mm) for the flexural strength, fracture toughness, and (50 × 30 × 30 mm) were fabricated for measuring hardness. PMMA without additives was prepared as a test control. Three types of mechanical tests;flexural strength, fracture toughness and hardness were carried out on the samples. The recorded values of flexural strength in (MPa), fracture toughness in (MPa.m1/2), and hardness (VHN) were collected, tabulated and statistically analyzed. One way analysis of variance (ANOVA) and Tukey’s tests were used for testing the significance between the means of tested groups which are statistically significant when the P value ≤ 0.05. Results: Addition of Zirconium oxide nanofillers to PMMA significantly increased the flexural strength, fracture toughness and hardness. Conclusion: These results indicate that Zirconium oxide nanofillers added to PMMA has a potential as a reliable denture base material with increased flexural strength, fracture toughness, and hardness. According to the results of the present study, the best mechanical properties were achieved by adding 7%wt ZrO2 concentration.

A Parametric Approach to the Evaluation of Flexural Strength of Advanced Ceramic or Glass Like Cylindrical Rods at Ambient Temperature

This critical review presents a parametric approach to the evaluation of flexural strength of advanced ceramic or glass like cylindrical rods at ambient temperature.The parameters governing the measurement and evaluation of flexure strengths of glasses and ceramics are detailed with references.The scope for improvement in the existing ASTM STM C-1684 standard is described with a logical rationale and the parameters that need to be addressed are listed and explained.

Modeling and Simulation of Wood and Fly Ash Behaviour as Partial Replacement for Cement on Flexural Strength of Self Compacting Concrete

Flexural strength was monitored and predicted on the application improving concrete strength with wood and fly as partial replacement for cement.The study observed the pressure from the constituent of these locally sourced material that has been observed from the study to influence the flexural strength through the effect from this locally sourced addictives.The study monitors concrete porosity on heterogeneity as it reflect on the flexural strength of self compacting concrete.Other condition considered was the compaction and placement of concrete.These effects were monitored at constant water cement ratio from design mix.The behaviour from this effects on the concrete observed the rate of flexural growth under the influences of these stated conditions.The simulation expressed the reactions of these effects through these parameters monitored to influence the system.Numerical simulations were also applied to the optimum curing age of twenty eight days,while analytical simulation was also applied.This concept is the conventional seven days interval that concrete curing were observed,these are improvement done on the study carried out by experts[16].These locally sourced material were experimentally applied.The simulation predictive values are at the interval of seven days of curing,which was also simulated.The predictive values were compared with the experimental values of the researchers[16],and both values developed best fits correlations.The study is imperative because the system considered the parameters used on experimental and observed other influential variables that were not examined.These were not observed in the experimental procedure.Experts in concrete engineering will definitely find these concept a better option in monitoring flexural strength of self compacting concrete in general.

Influence of Glass Fiber wt% and Silanization on Mechanical Flexural Strength of Reinforced Acrylics

The aim is to evaluate the flexural strength of acrylic resin bars depending on the addiction of glass fibers with or without previous 3-methacryloxypropyl-trimethoxysilane (silane) application. Short fibers (3 mm) were treated and added to an acrylic resin powder, being further mixed with acrylic liquid to create bars (25 × 2 × 2 mm) of 11 experimental groups (N = 10), according to the interaction of experimental factors: weight % of glass fibers: (0.5;1;3;4;6 and 7) and silane application (with silane (S) or without silane (N)). Flexural strength and scanning microscopy evaluation were performed (SEM). Data (MPa) were submitted to ANOVA and Tukey (α = 5%). A significant difference between groups was observed (p = 0.001): S7%(128.85 ± 35.76)a, S6% (119.31 ± 11.97)ab, S4% (116.98 ± 25.23)ab, N4% (107.85 ± 24.88)abc, S1% (96.29 ± 20.65)bc, S0.5% (89.29 ± 7.33)cd, S3% (89.0 ± 11.27)cd, N3% (86.79 ± 17.63)cd, N1% (85.43 ± 16.44)cd, Control (73.29 ± 25.0)de, N0.5% (59.58 ± 19.46)e. For N groups, it was not possible to include more than 4%wt fibers. SEM showed better fiber-resin interaction for S groups, and fractures around fibers on N groups. Previous silane application enables the addiction of greater quantity of glass fibers and better interaction with the acrylic resin resulting in higher flexural strength. Without silane, fibers seem to act as initial crack points due to poor interaction.

Effect of Environmental Conditions on Flexural Strength and Fracture Toughness of Particulate Filled Glass-Epoxy Hybrid Composites

Multifunctional hybrid polymer composites were projected as novel solutions to meet the demands in various industrial applications ranging from automotive to aerospace. This investigation focuses on processing, flexural strength and fracture toughness characterization of the glass fabric reinforced epoxy (G-E) composites and graphite/fly ash cenosphere (FAC) modified interface between the epoxy matrix and glass fabric. Hand lay-up followed by compression moulding method was used to fabricate the laminates. Flexural and fracture toughness tests at room temperature, elevated temperature and cryogenic temperature were conducted to assess the flexural strength (FS) and mode-I plane-strain fracture toughness (KIC). The experimental and characterization efforts suggest that both graphite and FAC fillers improve bonding at the interface. The study showed that the graphite is more favorable for enhancing FS and KIC of G-E composites. Graphite filled G-E hybrid composites with significant FS and KIC to that of unfilled and FA filled G-E were successfully achieved by incorporating 10 wt% graphite. The incorporation of fillers resulted in improvement of FS, which increased by 43% and 37.7% for 10Gr+G-E and 10FAC+G-E hybrid composites respectively. All composites show a 26% improvement in KIC at cryogenic temperature and a decrease of 12.5% at elevated temperature. According to the SEM observations, fiber debonding from the matrix is suppressed due to the presence and uniform distribution of graphite. In addition, micro-pores, matrix shearing, active toughening mechanisms induced by graphite, such as crack deflection, layer breakage and delamination of graphite layers contributed to the enhanced KIC of hybrid G-E composites.

Impact of Polymer Coating on the Flexural Strength and Deflection Characteristics of Fiber-Reinforced Concrete Beams

Liquid polymers(LP)have become an important structural material used in the construction industry in the last decade.This paper investigates the via­bility of using commercially available LPs as a coating material to improve the flexural strength of fiber-modified concrete beams.The scope included preparing rectangular prism concrete beams with a concrete mixture includ­ing fly ash and fiber and coating them with four different liquid polymers at a uniform thickness following the curing process while one set of sam­ples was maintained under the same conditions as a control group without coating.In addition,cylindrical samples were prepared to determine the compressive strength of the concrete mixture.Following the curing process in an unconfined open-air laboratory environment for another 28 days,con­crete samples were tested to determine the flexural strength and deflection characteristics under center point loading equipment.The results revealed that all four coating types enhanced both the flexural strength and the av­erage maximum deflection of the beams compared to the control group.While the enhancement in the flexural strength changed approximately between 5%and 36%depending on the coating type,the improvements in average maximum deflections varied between 3.7%and 28.4%.

Factorial Experimental Design to Study the Effects of Layers and Fiber Content on Concrete Flexural Behavior

Experimentation has come a long in helping researchers achieve breakthroughs in their different scientific areas and engineering happens to be one of those areas with the most impact from experimental advancement. The need for valid experimental results free from biases and confounding conclusions has prompted the development of new experimental techniques that takes consideration of all applicable factor and combinations in providing answers on a research topic, and the Factorial Experimental design credited to Sir Ronald Fisher is one technique yielding highly valid results. This paper uses the factorial design of experiments to research the flexural impact of polyvinyl acetate fiber and layered concrete in construction. The experiment considered two levels of fiber contents and two levels of layers, and prepared samples with all combinations of the variable factors. The samples were tested after 7 days from casting for flexural strength and an advance statistical analysis was performed on the flexural responses of the samples using R-program. The results from the analyses revealed the significance of the variables to the flexural strength of the samples, as well as their interactions. The experiment concluded that based on the number of layers and fiber content used for the experiment, casting concrete in layers does have a significant negative effect on the flexural strength of concrete, and the failure pattern of concrete members under flexural load in evidently influenced by the material composition of the concrete, and that it can be evidently influenced by casting the concrete in layers.

不同纤维对高强轻骨料混凝土力学性能影响及微观机理研究

为改善高强轻骨料混凝土的力学性能和弯曲韧性,研究了玄武岩纤维、细聚乙烯醇纤维、仿钢纤维、聚丙烯纤维和粗聚乙烯醇纤维的掺入对高强轻骨料混凝土抗压强度、劈裂抗拉强度和抗弯强度的影响规律。通过4点弯曲试验获取荷载-挠度曲线,基于韧性指标对比分析了5种纤维对高强轻骨料混凝土弯曲韧性的影响。通过扫描电子显微镜观察纤维破坏前后的表面微观形貌,阐释了不同纤维的增强增韧机理。研究结果表明:掺入纤维对高强轻骨料混凝土的力学性能均有提升,主要提升高强轻骨料混凝土的抗拉性能和弯曲韧性。粗聚乙烯醇纤维提升劈裂抗拉强度和抗弯强度程度最大,分别提高了83%和220%,使高强轻骨料混凝土破坏由脆性转为高延性。纤维对高强轻骨料混凝土抗拉性能和韧性的提升与纤维表面损伤程度成正比。