The performance of the Noblesse multi-collector noble gas mass spectrometer for ^(40)Ar/^(39)Ar geochronology

Noblesse multi-collector noble gas mass spec- trometer is specially designed for multi-collection of Ar isotopes with different beam sizes, especially for small ion beams, precisely, and hence is perfectly suitable for ^40Ar/^39Ar geochronology. We have analyzed widely used sanidine, muscovite, and biotite standards with recom- mended ages of - 1.2-133 Ma, with the aim to assess the reliability of Noblesse for ^40Ar/^39Ar dating. An ESI MIR10 30W CO2 laser was used for total fusion or incremental heating samples. Extracted gases were routinely purified by four SAES NP10 getters （one at - 400 ℃ and others at room temperature）. A GP50 getter and a metal cold finger cooled by liquid N （- 196 ℃） were also attached for additional purification if necessary. The Ar isotopes were then measured by Noblesse using Faraday or multiplier according to the signal intensities. Over a period of 1.5 months 337 air calibrations produced a weighted mean ^40Ar/^36Ar of 296.50 ± 0.08 （2σ, MSWD = 4.77）. Fish Canyon sanidine is used to calculate J-values, which show good linear relationship with position in irradiation. The age of four mineral standards （Alder Creek sanidine, Brione muscovite, Yabachi sanidine, and Fangshan biotite） are within error of the accepted ages. Five Alder Creek sanidine aliquots yielded an age range of 1.174-1.181 ± 0.013 Ma （2σ） which broadly overlaps the established age of the standard and the uncertainty approaches those of the foremost Ar/Ar laboratories in the world. The weighted mean ages of four Brione muscovite aliquots （18.75 i 0.16 Ma, 2σ）, five Yabachi sanidine aliquots （29.50 ± 0.19 Ma, 2σ）, and three Fangshan bio- tite aliquots （133.0 ± 0.76 Ma, 2σ） are consistent with the recommended values of these standards, and the uncer- tainties are typical of modem Ar/Ar laboratories world- wide.

A 5mW 1.8V Low Over-Sampling Ratio ΣΔ Modulator with 81dB Dynamic Range

This work demonstrates that the ΣΔ modulator with a low oversampling ratio is a viable option for the high-resolution digitization in a low-voltage environment.Low power dissipation is achieved by designing a low-OSR modulator based on differential cascade architecture,while large signal swing maintained to achieve a high dynamic range in the low-voltage environment.Operating from a voltage supply of 1.8V,the sixth-order cascade modulator at a sampling frequency of 4-MHz with an OSR of 24 achieves a dynamic range of 81dB for a 80-kHz test signal,while dissipating only 5mW.

A High-Performance Silicon Electro-Optic Phase Modulator with a Triple MOS Capacitor

We propose and analyze a novel Si-based electro-optic modulator with an improved metal-oxide-semiconductor （MOS） capacitor configuration integrated into silicon-on-insulator （SOl）. Three gate-oxide layers embedded in the silicon waveguide constitute a triple MOS capacitor structure, which boosts the modulation efficiency compared with a single MOS capacitor. The simulation results demonstrate that the Vπ Lπ product is 2. 4V · cm. The rise time and fall time of the proposed device are calculated to be 80 and 40ps from the transient response curve, respectively,indicating a bandwidth of 8GHz. The phase shift efficiency and bandwidth can be enhanced by rib width scaling.

Ridge Waveguide Electro-Optic Polymer Modulator with a New Kind of Corona Poled Crosslinkable Polyurethane

A polymer electro optic modulator has been fabricated with the functional layer acting as a kind of corona poled crosslinkable polyurethane. The three optical layers, namely waveguide, photolithography and oxygen are fabricated by spin coating. With the Reactive Ion Etching method, the ridge of the waveguide is constructed. With light at 1 31μm being fiber coupled to waveguide, the mode and the modulation properties of these devices are demonstrated in a micron control system.

Monolithically Integrated Laser Diode and Electroabsorption Modulator with Dual-Waveguide Spot-Size Converter Output

A 1.60μm laser diode and electroabsorption modulator monolithically integrated with a novel dual-waveguide spot-size converter output for low-loss coupling to a cleaved single-mode optical fiber are demonstrated.The devices emit in a single transverse and quasi single longitudinal mode with an SMSR of 25.6dB.These devices exhibit a 3dB modulation bandwidth of 15.0GHz,and modulator DC extinction ratios of 16.2dB.The output beam divergence angles of the spot-size converter in the horizontal and vertical directions are as small as 7.3°×18.0°,respectively,resulting in a 3.0dB coupling loss with a cleaved single-mode optical fiber.

Butt-Joint Monolithically Integrated DFB-LD/EA-MD Light Source for 10Gbit/s Transmission

This paper reports on the design,fabrication,and performance of an integrated electro-absorptive modulated laser based on butt-joint configuration for 10Gbit/s application.This paper mainly aims at two aspects.One is to improve the optical coupling between the laser and modulator;another is to increase the bandwidth of such devices by reducing the capacitance parameter of the modulator.The integrated devices exhibit high static and dynamic characteristics. Typical threshold current is 15mA,with some value as low as 8mA.Output power at 100mA is more than 10mW.The extinction characteristics,modulation bandwidth,and electrical return loss are measured.3dB bandwidth more than 10GHz is monitored.

An Electroabsorption Modulator Monolithically Integrated with a Semiconductor Optical Amplifier and a Dual-Waveguide Spot-Size Converter

A semiconductor optical amplifier and electroabsorption modulator monolithically integrated with a spotsize converter input and output is fabricated by means of selective area growth,quantum well intermixing,and asymmetric twin waveguide technology. A 1550-1600nm lossless operation with a high DC extinction ratio of 25dB and more than 10GHz 3dB bandwidth are successfully achieved. The output beam divergence angles of the device in the horizontal and vertical directions are as small as 7.3°× 18.0°, respectively, resulting in a 3.0dB coupling loss with a cleaved single-mode optical fiber.

A Wavelength Tunable DBR Laser Integrated with an Electro-Absorption Modulator by a Combined Method of SAG and QWI

We report a wavelength tunable electro-absorption modulated DBR laser based on a combined method of SAG and QWI. The threshold current is 37mA and the output power at 100mA gain current is 3.5mW. When coupled to a single-mode fiber with a coupling efficiency of 15% ,more than a 20dB extinction ratio is observed over the change of EAM bias from 0 to -2V. The 4.4nm continuous wavelength tuning range covers 6 channels on a 100GHz grid for WDM telecommunications.

A Novel Hybrid DPWM for Digital DC-DC Converters

We present a new hybrid digital pulse-width modulator （DPWM） for digital DC-DC converters that employs a ring-oscillator/counter structure. Based on a temperature/process compensation technique and a novel digital controller, the proposed DPWM can not only offer temperature/process-independent pulse widths, but also operate at a much higher clock frequency than the existing delay-line/counter DPWM structure. Post-simulation results show that with our DPWM, the system clock frequency reaches 156.9MHz while the worst variation,in a temperature range of 0 to 100℃under all process corners,is only± 9.4%.

CMOS Quadrature Modulator and Up-Conversion Mixer for 802.11a Wireless LAN Systems

A quadrature modulator and an up-conversion mixer for an 802. lla wireless LAN system are designed and fabricated in 0.18μm gate length standard CMOS technology. A current feedback loop with a transconductor is used to improve the linearity of the quadrature modulator;An LC resonant tank is used as the load of the upconversion mixer to improve its gain and increase the voltage swing. The measurement results show that the input P1dB achieves -3.6dBm, the transducer power gain of the circuit is -3.6dB,and the current consumes about 45.8mA with a 1.8V power supply.

Analysis and design of sigma-delta interface circuit for quartz flexural pendulum accelerometer

For the high resolution required in a digital interface circuit of an accelerometer used in feeble gravity measurement, a switched-capacitor （SC） sigma-delta modulator （SDM） is proposed. Based on the principle and the topology structure of the SDMs, the influence of oversampling ratio, bits of an internal quantizer and the cascaded structure on weak signal detecting precision is analyzed, and an ideal low-distortion SDM with a second-order 1-bit structure satisfying the high- resolution interface circuit of an accelerometer is designed. With the research on non-idealities of each SDM block in the SC circuit implementation and their impacts on power consumption, the realized parameters of low-power SDMs based on different bandwidths are devised and the power consumption of each SDM is estimated. Time-domain behavioral simulation is explored based on Simulink. The results demonstrate that a 21- bit resolution of the designed SDMs can be achieved on the premise of low power, and the parameters for the circuit implementation can be directed to the transistor-level circuit design.

DIGITAL PWM OF AC-AC MATRIX CONVERTER BASED ON OUTPUT-VOLTAGE ERROR FUNCTION

Based on the output-voltage error function, a novel time discrete modulation technique is proposed for matrix converters （MCs） and time-discrete difference equations of a MC circuit are derived. Switch states of MC are obtained when the output voltage error function is minimized, thus the optimum combination of switch states is derived for the closed-loop control of MC. Meanwhile, advantages of the least calculation workload, the simple process, and the convenient for implementation are brought while switch states are described as space vectors in the α-β coordination system. Simulation and experimental results demonstrate the validity of the time-discrete modulation technique and the feasibility of the control approach.

Soft-switching PWM boost full-bridge converter

This paper proposes a family of PWM modulation strategies for boostfull-bridge (FB) converters. The modulation strategies can be classified into two kinds according tothe turn-on sequence of the diagonal switches. The concept of leading switches and lagging switchesis introduced to realize soft-switching. According to the soft-switching realized by the leadingswitches and the lagging switches, two kinds of soft-switching techniques for PWM boost FBconverters yield: zero-current-switching (ZCS) and zero-current and zero-voltage-switching (ZCZVS).Simulation results verify the analysis.

A generic PWM strategy for multi-leg VSI-fed machine drives

A generic pulse width modulation（PWM） strategy is proposed for the multi-leg voltage source inverter（VSI）.First, the multi-leg VSI is modeled, which is independent from the load structure. Secondly, the proposed PWM strategy is deduced by inverting the mathematical model of the multileg VSI. According to the relationship between the leg number of VSIs and the phase number of electrical machines, the multi-leg VSI-fed machine drives are classified into two types：matched and unmatched applications. The leg numbers of VSIs and the phase number of electrical machines are equal in matched applications while they are different in unmatched applications. The existing PWM strategies cannot be directly used for both matched and unmatched applications. However,the proposed PWM strategy can be general for both matched and unmatched applications, and no modifications are required. The effectiveness of the proposed PWM strategy is verified by experimental results.

ZERO-CURRENT AND ZERO-VOLTAGE SWITCHING PWM BOOST FULL-BRIDGE CON VERTER

This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load range using the energy of the output capacitor. Ma king use of parasitic capacitors of the lagging switches and parallel auxiliary i nductance with the primary winding of the transformer, the lagging switches can realize zero voltage switching (ZVS) under any load. Compared with the ZCS PWM Boost FB converter, the new converter has no current duty cycle loss. Operat ional principle and parameter design are analyzed. Experimental results verify the effectiveness of the proposed converter.

A High-PSRR CMOS Bandgap Reference Without Resistor

A CMOS bandgap reference （BGR） without a resistor,with a high power supply rejection ratio and output be- low 1V is proposed. The circuit is suited for on-chip voltage down converters. The BGR is designed and fabricated using an HUTC 0.18μm CMOS process. The silicon area is only 0. 031mm^2 excluding pads and electrostatic-discharge （ESD） protec- tion circuits. Experimental results show that the PSRR of the proposed BGR at 100Hz and lkHz achieves, respectively, - 70 and 62dB using the pre-regulator. The proposed BGR circuit generates an output voltage of 0. 5582V with a varia- tion of 1.5mV in a temperature range from 0 to 85℃. The deviation of the output voltage is within 2mV when the power supply voltage VDD changes from 2.4 to 4V.

Mach-Zehnder Electro-Optic Polymer Modulator with C orona Poled Core Layer

A Mach-Zehnder(MZ) electro-optic(EO) modulator are real iz ed,with three optical layers as polymer materials.The functional layer is the co rona poled crosslinkable polyurethane.The ridge waveguide is fabricated by using the spin-coating,poling,photolithography and oxygen reactive ion etching(RIE) techniques.The mode and the modulation properties of these devices are demonstra ted in a micron control system,while the light source works at the wavelength of 1 31 or 1 55 micron.

Monolithic Integration of Electro-Absorption Modulators and DFB Lasers by Modified Double Stack Active Layer Approach

Monolithic electro absorption modulated distributed feedback(DFB) lasers are proposed and fabricated by using a modified double stack active layer.The 38mA threshold,9dB extinction ratio (from 0 5V to 3 0V),and about 5mW output power at the 100mA operation current are achieved.Compared with other reported results (only 1 5mW at the same operation current) of the traditional stack active structure,the proposed structure improves the output power of devices.

A Novel Method to Compensate the Sigma-Delta Shaped Noise for Wide Band Fractional-N Frequency Synthesizers

A novel method to partially compensate sigma-delta shaped noise is proposed. By injecting the compensation current into the passive loop filter during the delay time of the phase frequency detector（PFD）,a maximum reduction of the phase noise by about 16dB can be achieved. Compared to other compensation methods,the technique proposed here is relatively simple and easy to implement. Key building blocks for realizing the noise cancellation,including the delay variable PFD and compensation current source, are specially designed. Both the behavior level and circuit level simulation results are presented.

An 80dB Dynamic Range ΣΔ Modulator for Low-IF GSM Receivers

A high-resolution,200kHz signal bandwidth,third-order single-loop single-bit ε△ modulator used in low-IF GSM receivers is presented. The modulator is implemented with fully differential switched capacitor circuits in standard 0. 6μm 2P2M CMOS technology. The modulator uses two balanced reference voltages of ±1V,and is driven by a single 26MHz clock signal. The measurement results show that,with an oversampling ratio of 64, the modulator achieves an 80.6dB dynamic range,a 71.8dB peak SNDR,and a 73.9dB peak SNR in the signal bandwidth of 200kHz. The modulator dissipates 15mW static power from a single 5V supply.