深水采油树Spring-Seal密封圈接触模型构建与实验测试

为提高深水采油树在高压、高温、低温等工况下长时间工作的稳定性,对采油树密封圈进行重新设计,提出Spring-Seal密封圈(以下简称S密封圈);基于赫兹接触理论、填料密封接触理论,重新构建S密封圈接触力学模型;建立有限元仿真分析模型,分析不同条件下S密封圈的密封性能,同时验证新建接触模型的合理性;利用实验测试S密封圈的实际密封效果。研究结果表明:S密封圈在高压、高温、低温等工况下能够长时间稳定工作且密封性能良好。研究结果可为S密封圈的接触研究及工程运用提供理论参考。

Analysis of Force Characteristic and Friction State on the Sealing Ring Used in Composite Transmission

Based on analysis of flow field of the rotary seal using sealing ring, mechanical models under the condition of full film friction and mixed film friction were established respectively. The influence of friction state of the sealing ring on seal performance was also discussed. The relation between force characteristic and structural parameters of the sealing ring was analyzed. Analytical results indicate that friction state mainly depends on structural parameters of the sealing ring. The expression of calculating friction torque under the condition of mixed film friction was deduced. Experiment verification had been done. Experimental results agree with the deducing theoretical conclusions on the whole. It lays the foundation for design of new type of sealing ring used in composite transmission.

Rupture of an Infrarenal Aortic Aneurysm Due to a Secondary Type 1a Endoleak Following Endovascular Aneurysm Sealing with the Nellix^®Device

Purpose: The Nellix endovascular aneurysm sealing (EVAS) system was introduced in 2010 for infrarenal abdominal aortic aneurysm (AAA) repair. So far one secondary type 1a endoleak resulting in rupture of the aneurysm has been reported. Case report: We present a case of a rupture of an infrarenal aortic aneurysm due to a secondary type 1a endoleak caused by stent migration 14 months after endovascular aneurysm sealing with a Nellix system. Conclusion: Strict adherence to anatomical requirements given by the instructions for use during patient selection and thorough post interventional surveillance may reduce the probability of secondary type 1a endoleaks. Furthermore, device design changes, especially concerning the configuration of the proximal part of the stent graft, have to be considered.

Stress and thickness calculation of a bolted flat cover with double metal sealing rings

The design of a bolted flat cover is extremely important for the structural integrity of pressure vessels.The present design codes provide the thickness calculation equations for a bolted flat cover with single metal gasket.However,the rules for a bolted flat cover with double metal sealing rings are not developed to date.In the study,a new thickness calculation equation for the bolted flat cover with double metal sealing rings is proposed.First,the theoretical stress solution for bolted flat cover with the double metal sealing rings is obtained,based on the theory of simply supported circular plate and then verified using the results from finite element analyses.The results indicate that the influence of double metal sealing ring on the stress of the flat cover is more serious compared to single metal gasket.Second,a more accurate and reasonable equation is proposed to calculate the thickness of bolted flat cover with double metal sealing rings based on the derived theoretical equations of maximum stress.Finally,the influence of linear load and the spacing between rings on the thickness are discussed.Subsequently,a few suggestions are provided to design low-pressure or atmosphere pressure vessels.The study provides a theoretical foundation to develop design codes of pressure vessels in nuclear reactors.

Metal Sealing Performance of Subsea X-tree Wellhead Connector Sealer

The metal sealing performance of subsea X-tree wellhead connectors is crucial for the safety and reliability of subsea X-trees. In order to establish the theoretical relation between metal sealing ring＇s contact stress and its structural parameters and working pressure, a mechanical analysis method for double-cone sealing of high pressure vessels is applied in analyzing the metal sealing ring under the condition of preload and operation. As a result, the formula of the unit sealing load for the metal sealing ring under operation with residual preload is shown in this paper, which ensures that the metal sealing ring has an excellent sealing effect and can prevent the metal sealing ring from yielding. Besides, while analyzing the sealing process of the metal sealing ring, the change rule of contact stress and working pressure is concluded here, putting forward that the structural parameters of the metal sealing ring are the major factors affecting the change rule. Finally, the analytical solution through theoretical analysis is compared with the simulation result through finite element analysis in a force feedback experiment, and both are consistent with each other, which fully verifies for the design and calculation theory on metal sealing ring＇s contact stress and its structural parameters and working pressure deduced in this paper. The proposed research will be treated as an applicable theory guiding the design of metal seal for subsea X-tree wellhead connectors.

Synthesis of Schiff Base Type Macrocycles Containing Naphthalene Ring

A series of new Schiff base type macrocyclic crown ethers containing naphthalene ring were synthesized from 2,2'-di(o-formylnaphthoxy) ethyl ether or 1,2-di(o-formylnaphthoxy) ethane and four appropriate diamines. The chemical structures of the new compounds were characterized by elemental analysis, infrared spectra, nuclear magnetic resonance spectra and mass spectrometry.

Influence Analysis of Secondary O-ring Seals in Dynamic Behavior of Spiral Groove Gas Face Seals

The current research on secondary O-ring seals used in mechanical seals has begun to focus on their dynamic properties. However, detailed analysis of the dynamic properties of O-ring seals in spiral groove gas face seals is lacking. In particular a transient study and a difference analysis of steady-state and transient performance are imperative. In this paper, a case study is performed to gauge the effect of secondary O-ring seals on the dynamic behavior（steady-state performance and transient performance） of face seals. A numerical finite element method（FEM） model is developed for the dynamic analysis of spiral groove gas face seals with a flexibly mounted stator in the axial and angular modes. The rotor tilt angle, static stator tilt angle and O-ring damping are selected to investigate the effect of O-ring seals on face seals during stable running operation. The results show that the angular factor can be ignored to save time in the simulation under small damping or undamped conditions. However, large O-ring damping has an enormous effect on the angular phase difference of mated rings, affecting the steady-state performance of face seals and largely increasing the possibility of face contact that reduces the service life of face seals. A pressure drop fluctuation is carried out to analyze the effect of O-ring seals on the transient performance of face seals. The results show that face seals could remain stable without support stiffness and O-ring damping during normal stable operation but may enter a large-leakage state when confronting instantaneous fluctuations. The oscillation-amplitude shortening effect of O-ring damping on the axial mode is much greater than that on the angular modes and O-ring damping prefers to cater for axial motion at the cost of angular motion. This research proposes a detailed dynamic-property study of O-ring seals in spiral groove gas face seals, to assist in the design of face seals.

Fluid-solid Interaction Model for Hydraulic Reciprocating O-ring Seals

Elastohydrodynamic lubrication characteristics of hydraulic reciprocating seals have significant effects on sealing and tribology performances of hydraulic actuators, especially in high parameter hydraulic systems. Only elastic deformations of hydraulic reciprocating seals were discussed, and hydrodynamic effects were neglected in many studies. The physical process of the fluid-solid interaction effect did not be clearly presented in the existing fluid-solid interaction models for hydraulic reciprocating O-ring seals, and few of these models had been simultaneously validated through experiments. By exploring the physical process of the fluid-solid interaction effect of the hydraulic reciprocating O-ring seal, a numerical fluid-solid interaction model consisting of fluid lubrication, contact mechanics, asperity contact and elastic deformation analyses is constructed with an iterative procedure. With the SRV friction and wear tester, the experiments are performed to investigate the elastohydrodynamic lubrication characteristics of the O-ring seal. The regularity of the friction coefficient varying with the speed of reciprocating motion is obtained in the mixed lubrication condition. The experimental result is used to validate the fluid-solid interaction model. Based on the model, The elastohydrodynamic lubrication characteristics of the hydraulic reciprocating O-ring seal are presented respectively in the dry friction, mixed lubrication and full film lubrication conditions, including of the contact pressure, film thickness, friction coefficient, liquid film pressure and viscous shear stress in the sealing zone. The proposed numerical fluid-solid interaction model can be effectively used to analyze the operation characteristics of the hydraulic reciprocating O-ring seal, and can also be widely used to study other hydraulic reciprocating seals.

Gastric adenocarcinoma of fundic gland type with signet-ring cell carcinoma component: A case report and review of the literature

A depressed lesion was found at a gastric angle of 76-yearold Japanese woman by esophagogastroduodenoscopy. Four years prior, she was diagnosed with a Helicobacter pylori infection but no eradication was performed. The pathological diagnosis of biopsy specimens was signet-ring cell carcinoma. Endoscopic submucosal dissection(ESD) was performed. Histopathological examination of the ESD specimen revealed proliferation of well-differentiated tubular adenocarcinoma mimicking fundic gland cells at the deep layer of the lamina propria mucosae. These tumor cells expressed focally pepsinogen-Ⅰ, diffusely MUC6, and scattered H^+/K^+ ATPase according to immunohistochemistry. Therefore, we diagnosed this tumor as gastric adenocarcinoma of fundic gland type(GA-FG). Adjacent to the GA-FG, proliferation of signet-ring cell carcinoma which diffusely expressed MUC 2 and MUC 5AC was observed. Intestinal metaplasia was focally observed in the surrounding mucosa of the signet-ring cell carcinoma. To the best of our knowledge, this is the first case report of GA-FG with a signet-ring cell carcinoma component. The origin of signet-ring cell carcinoma, i.e., whether it accidentally arose from a non-neoplastic mucosa and coexisted with the GA-FG or dedifferentiated from the GA-FG is unclear at present. We expect the accumulation of similar cases and further analysis to clarify this issue.

EFFICIENCY ANALYSIS OF DOUBLE CRANK RING-PLATE-TYPE PIN-CYCLOIDAL GEAR PLANETARY DRIVE

From the general formula for calculating the efficiency of planetary geartrains, the efficiency of the double crank ring-plate-type pin-cycloidal gear planetary drive isderived. To prove the theory, an experimental study has been conducted. The tested value of theefficiency of a sample set of the new-type drive in the experiment agrees with the calculated one.It shows that the new-type drive is of not merely high bearing capacity, but also quite highefficiency.

Enhancement of seal life through carbon composite back-up rings under shock loading conditions in defence applications

The life of Nitrile Butadiene Rubber(NBR) O-ring seal having shore hardness of A70 and A90 under shock loading conditions was investigated by a specially designed pneumo-hydraulic shock test rig. Shock tests have been carried out on bare seals, seal with conventional polytetrafluoroethylene(PTFE) back-up rings and seal with newly developed carbon composite back-up rings to study its behaviour under different operating conditions until failure. Experiments were conducted by varying annular gap ranging from 0.3 to 0.5 mm, oil temperature from 30 ℃ to 70 ℃ and rate of pressure rise from 600 to 2400 MPa/s. Significant enhancement in seal life was observed with carbon composite back-up ring at reduced annular clearances compared to seal life with conventional PTFE back-up ring and without back-up rings.

A Novel Design and Fabrication of Magnetic Random Access Memory Based on Nano-ring-type Magnetic Tunnel Junctions

Nano-ring-type magnetic tunnel junctions （NR-MTJs） with the layer structure of Ta（5）/Ir22Mn78（10）/ Co75Fe25（2）/Ru（0.75）/CoooFe20B20（3）/Al（0.6）-oxide/Co60Fe20B20（2.5）/Ta（3）/Ru（5） （thickness unit： nm） were nano-fabricated on the Si（100）/SiO2 substrate using magnetron sputtering deposition combined with the optical lithography, electron beam lithography （EBL） and Ar ion-beam etching techniques. The smaller NR-MTJs with the inner- and outer-diameter of around 50 and 100 nm and also their corresponding NR-MTJ arrays were nano-patterned. The tunnelling magnetoresistance （TMR ＆ R） versus driving current （I） loops for a spin-polarized current switching were measured, and the TMR ratio of around 35% at room temperature were observed. The critical values of switching current for the free Co60Fe20B20 layer relative to the reference Co6oFe2oB2o layer between parallel and anti-parallel magnetization states were between 0.50 and 0.75 mA in such NR-MTJs. It is suggested that the applicable MRAM fabrication with the density and capacity higher than 256 Mbit/inch2 even 6 Gbite/inch2 are possible using both I NR-MTJ＋1 transistor structure and current switching mechanism based on based on our fabricated 4×4 MRAM demo devices.

A ring type standing wave ultrasonic motor using cantilever type longitudinal transducers

The disadvantages of classic ring type ultrasonic motor were analyzed.To obtain large mechanical output power,a ring type standing wave ultrasonic motor using cantilever type longitudinal transducers was proposed.There are four pairs of cantilevers on one side of the ring,and four PZT ceramics are set between each pair of cantilevers.A screw fastened the PZT ceramics and cantilevers together to form a longitudinal transducer.The bending vibration mode of the ring is excited by the stretching vibration of the PZT ceramics.Thus,linear simple harmonic motions are achieved at the particle on the teeth.And the driving force is the frictional force between rotor and stator.The working principle of the proposed motor was analyzed.The ring and the longitudinal transducer were designed with FEM.The sensitive parameters of resonant frequency of the transducer and ring could be gained with modal analysis.The longitudinal vibration modal of transducer and bending vibration modal of ring were degenerated,and the motion trajectories of nodes on the teeth were analyzed.The results of this paper could guide the development of this new type of motor.

Presentation of signet ring cell type at carcinoma ventriculi of the patient aged 20 years old

Introduction: Diffuse variant of GC is composed of gastric-type mucous cells, which generally do not form glands, but rather permit the mucosa and wall as scattered individual cells or small clusters in an “infiltrative” growth pattern. These cells appear to arise from the middle layer of the mucosa, and the presence of intestinal metaplasia is not a prerequisite. In this version, mucin formation expands the malignant cells and pushes the nucleus to the periphery, creating a “signet ring” conformation. If the signetring cells are more than 50% of the tumor, the tumor is classified as signetring cell carcinoma [1]. This case is important for reporting because we encountered for the first time such a carcinoma type, due to the new age and its atypical presentation. Case Presentation: We report a case of a 20 years Albanian old patient with Signet Ring Cell Type of Gastric CA. The patient was brought at the urgency with severe abdominal pain, nausea and peritoneal irritation. Clinical examination has been made in emergency, where we conclude the signs of peritoneal irritation, from native Ro no signs of pneumoperitoneum, while laboratory tests found a slight anemia (erythrocytes 3.36, HCT 25, HGB 8.6). Two hours later we repeated the native RTG and there were present the signs of pneumoperitoneum. It was indicated urgent surgical in-tervention. Intraoperatively, we found Ulcer duodenal perforation and?undertook the operation procedures by Roscoe Graham technique. Conclusions: At this age, it is rare, and it is difficult to detect in its early stages, because the signs and symptoms are often non-existent, non-specific, or mimic as an ulcer. The most common symptoms are early heartburn indigestion, abdominal pain or discomfort, vomiting, constipation, diarrhea or to feel of filling after a small meal, loss of appetite, weakness and fatigue. Less common symptoms are anemia and weight loss.

In-Line Inspection of Pipeline Defects Detection Using Ring-Type Laser

Pipeline plays a vital role in transporting fluids like oils, water, and petrochemical substances for longer distances. Based on the materials they carry, prolonged usage may cause the initiation of defects in the pipeline. These defects occur due to the formed salt deposits, chemical reaction happens between the inner surface and the transferring substance, prevailing environmental conditions, etc. These defects, if not identified earlier may lead to significant losses to the industry. In this work, an in-line inspection system utilizes the nondestructive way for analyzing the internal defects in the petrochemical pipeline. This system consists of a pipeline inspection robot having two major units namely the visual inspection unit and the power carrier unit. The visual inspection unit makes use of a ring-type laser diode and the camera. The laser diode serves as a light source for capturing good quality images of inspection. This unit is controlled by the Arduino in the power carrier unit which provides the necessary movement throughout the pipe. The inspected images captured by the camera are further processed with the aid of NI vision assistant software. After applying the processing function parameters provided by this software, the defect location can be clearly visualized with high precision. Three sets of defects are introduced in a Polylactide (PLA) pipe based on its position and angle along the circumference of the pipe. Further, this robot system serves as a real-time interactive image synchronization system for acquiring the inspected images. By comparing the actual and calculated defect size, the error percentage obtained was less than 5%.

Syntheses of Cellulose-Type Polysaccharide by Means of Ring-Opening Copolymerization of Anhydroriboses ABRP and AIRP

Two kinds of 1,4-anhydroribose derivatives,1,4-anhydro-2,3-O-benzylidene-T-D-ribopyranose(ABRP)and 1,4-anhydro-2,3-O-isopropylidene-T-D-ribopyranose(AIRP)were prepared fromD-ribose.The ringopening copolymerizations of ABRP and AIRP in various feed ratios were carried out with SbCl_5 and BF_3OEt_2 as catalyst at low temperatures.The copolymer structure was characterized by means of ^(1)H,^(13)C NMR spectroscopy and specific rotation.When SbCl_(5)was used as catalyst,the copolymer obtained had completely 1,4-β-pyranosidic structure,i.e.,cellulosetype structure.However,when BF_(3)OEt_2 was used as catalyst,the copolymer had a mixed structure of furanosidic and pyranosidic units.

Characterization of a Novel RING-Type Ubiquitin E3 Ligase GhRING2 Differentially Expressed in Cotton Fiber

The ubiquitin-proteasome proteolysis pathway is responsible for the degradation of abnormal and short-lived proteins to regulate many important biochemical activities in eukaryotes. By employing affymetrix microarray analysis, we have identified a novel ubiquitin ligase E3 gene GhRING2 that is differentially expressed between two Gossypium hirsutum lines-Texas Marker-1 (TM-1) and Chromosome Substitution Line CS-B25. The CS-B25 line has chromosome 25 from G. barbadense substituted into TM-1. The complete nucleotide sequences of GhRING2 along with its 5’-flanking region were obtained by genomic walking. GhRING2 was highly expressed in elongating fiber, and GUS expression directed by the GhRING2 promoter was found in hypocotyls and young stems of transgenic Arabidopsis plants. Using a yeast two-hybrid assay GhRING2 was found to interact with a PROTODERMAL FACTOR1 (GhPDF1) protein. GhPDF1 was expressed preferentially in immature ovules and fiber initials, and the GhPDF1 gene had been suggested to play a role in cell fate determination and fiber development. Pull down and plasmid swap assays further confirmed the interaction between GhRING2 and GhPDF1. The expression and protein interaction data indicate that GhRING2 may be involved in the turnover of GhPDF1 and participation in the transition from initiation to elongation stages during fiber development. Our data strongly suggest that the ubiquitin-proteasome pathway may regulate cotton fiber growth and development. The nucleotide sequence data of GhRING2 in this article have been submitted to the Gen Bank Nucleotide Sequence Data Bases under the accession number BankIt 1,742,008 SeqKM 108,000.

基于PTFE矩形密封圈的高压容器密封结构设计

PTFE矩形密封圈具有耐化学性能好、截面稳定性高等优点,可以有效解决腐蚀性介质的密封问题。但在实际使用中,PTFE矩形密封圈及其适配沟槽的尺寸设计缺乏参考依据。针对上述问题,根据高压容器端面密封结构的形状与受力特征,在Ansys Workbench中建立PTFE矩形密封圈的二维轴对称模型,采用双线性等向强化模型表征PTFE的力学性能,对基于PTFE矩形密封圈的高压容器端面密封结构进行分析和设计,讨论压缩率、PTFE矩形密封圈几何参数和沟槽结构参数对高压容器端面密封性能的影响。结果表明,压缩率、矩形圈的高度和宽度以及矩形圈与沟槽侧壁的间隙对密封性能的影响较大,而内径对密封性能的影响较小,因而设计时应优先考虑沟槽深度、矩形圈的截面尺寸以及与沟槽的装配位置等参数。确定PTFE矩形密封圈及适配沟槽的尺寸后,采用有限元仿真手段验证了设计的密封结构在常温30 MPa高压下的密封性能,证实了设计的合理性。

Organic matter transformation ratio, hydrocarbon expulsion efficiency and shale oil enrichment type in Chang 7_(3) shale of Upper Triassic Yanchang Formation in Ordos Basin, NW China

The major enrichment type of shale oil in the Chang 7_(3) shale of Upper Triassic Yanchang Formation in the Ordos Basin is unknown.This paper analyzes the organic matter transformation ratio,hydrocarbon expulsion efficiency and roof/floor sealing conditions of the Chang 7_(3) shale,and evaluates the major enrichment type of shale oil in this interval.The average organic matter transformation ratio of the Chang 7_(3) shale is about 45%;in other words,more than 50%of the organic matters have not transformed to hydrocarbons,and the lower the maturity,the greater the proportion of untransformed organic matters.The cumulative hydrocarbon expulsion efficiency of the transformed hydrocarbon is 27.5% on average,and the total proportion of untransformed organic matters plus retained hydrocarbons is greater than 70%.The relative hydrocarbon expulsion efficiency of the Chang 7_(3) shale is 60%on average,that is,about 40% of hydrocarbons retain in the shale.The Chang 7_(3) shale corresponds to Chang 7_(1+2) and Chang 8 sandstones as the roof and floor,respectively,and is further overlaid by Chang 6 shale,where extensive low porosity and low permeability–tight oil reservoirs have formed in the parts with relatively good porosity and permeability.Moreover,the Chang 7_(3) shale is tested to be in a negative pressure system(the pressure coefficient of 0.80–0.85).Therefore,the roof/floor sealing conditions of the Chang 7_(3) shale are poor.The retained hydrocarbons appear mostly in absorbed status,with low mobility.It is concluded that the medium–high mature shale oil is not the major enrichment type of shale oil in the Chang 7_(3) shale,but there may be enrichment opportunity for shale oil with good mobility in the areas where the sealing conditions are good without faults and fractures and oil reservoirs are formed off Chang 7_(1+2),Chang 6 and Chang 8.Furthermore,low–medium mature shale oil is believed to have great potential and is the major enrichment type of shale oil in the Chang 7_(3) shale.It is recommended to prepare relevant in-situ conversion technologies by pilot test and figure out the resource availability and distribution.

10kV箱变改造为发电机转子护环感应加热电源的研究与应用

在某核电站汽轮发电机转子首次检修和绕组发生绝缘缺陷时,需要采用感应加热法拆除转子护环进行检查与处理。本文结合电站实际情况及护环拆装需求,经过分析与计算,按照最优的单绕组供电方案将工程建设期退役的10kV箱式变电站改造成拆装发电机转子护环所需的感应加热电源,并在两台百万千瓦级汽轮发电机的首次大修和转子绝缘缺陷处理中实现成功应用,有效保障了核电站发电机大修工期,节约了大修成本。