To enhance the protective performance of ceramic composite armor,ballistic penetration experiments were conducted on Al_(2)O_(3) ceramic-ultra-high molecular weight polyethylene(UHMWPE)composite armor with different t...To enhance the protective performance of ceramic composite armor,ballistic penetration experiments were conducted on Al_(2)O_(3) ceramic-ultra-high molecular weight polyethylene(UHMWPE)composite armor with different thickness configurations.The damage and failure modes of hard projectiles and ceramic-fiber composite targets were analyzed.The recovered projectiles and ceramic fragments were sieved and weighed at multiple stages,revealing a positive correlation between the degree of fragmentation of the projectiles and ceramics and the overall ballistic resistance of the composite targets.Numerical simulations were performed using the LS-DYNA finite element software,and the simulation results showed high consistency with the experimental results,confirming the validity of the material parameters.The results indicate that the projectile heads primarily exhibited crushing and abrasive fragmentation.Larger projectile fragments mainly resulted from tensile and shear stress-induced failure.The failure modes of the composite targets included the formation of ceramic cones and radial cracks under high-velocity impacts.The UHMWPE laminated plates exhibited interlayer separation caused by tensile waves,permanent plastic deformation of the rear surface bulging,and perforation failure primarily due to shear forces.Through extended numerical simulations,while maintaining the same areal density and configuration of9 mm Al_(2)O_(3) ceramic+12 mm UHMWPE laminated composite armor,the thickness configurations of the Al_(2)O_(3) ceramic and UHMWPE laminated backplates were varied,and various thicknesses of UHMWPE laminates were simulated as the cover layer for the ceramic panels.The simulation results indicated that the composite armor configuration of 10 mm Al_(2)O_(3) ceramic+8 mm UHMWPE composite armor increased energy absorption by13.48%.When altering the cover layer thickness,a 4 mm UHMWPE+9 mm Al_(2)O_(3)+8 mm UHMWPE composite armor demonstrated a 27.11%improvement in energy absorption,showing a relatively significant enhancement.展开更多
Superwetting materials have drawn unprecedented attention in the treatment of oily wastewater due to their preferable anti-fouling property and selective oil/water separation.However,it is still a challenge to fabrica...Superwetting materials have drawn unprecedented attention in the treatment of oily wastewater due to their preferable anti-fouling property and selective oil/water separation.However,it is still a challenge to fabricate multifunctional and environmentally friendly materials,which can be stably applied to purify the actual complicated wastewater.Here,a Ag/Ag/α-Fe_(2)O_(3) heterostructure anchored copper mesh was intentionally synthesized using a facile two-step hydrothermal method.The resultant mesh with superhydrophilicity and underwater superoleophobicity was capable of separating various oil/water mixtures with superior separation efficiency and high permeationflux driven by gravity.Benefiting from the joint effects of the smaller band gap of Ag/α-Fe_(2)O_(3) heterojunction,inherent antibacterial capacity of Ag/α-Fe_(2)O_(3) and Ag nanoparticles,favorable conductive substrate,as well as the hierarchical structure with superwettability,such mesh presented remarkably enhanced degradation capability toward organic dyes under visible light irradiation and antibacterial activity against both Escherichia coli(E.coli)and Staphylococcus aureus(S.aureus)compared with the pure Ag/α-Fe_(2)O_(3) coated mesh.Impressively,the mesh exhibited bifunctional water purification performance,in which organic dyes were eliminated simultaneously from water during oil/water separation in onefiltration process.More importantly,this mesh behaved exceptional chemical resistance,mechanical stability and long-term reusability.Therefore,this material with multifunctional integration may hold promising potential for steady water purification in practice.展开更多
Nd2O3 doped BaTiO3ceramics（the additive content was respectively 0.001, 0.002, 0.003, 0.005, 0.01 molar ratio）were prepared by Sol-Gel method to study their dielectric characteristics and electric conductivities thr...Nd2O3 doped BaTiO3ceramics（the additive content was respectively 0.001, 0.002, 0.003, 0.005, 0.01 molar ratio）were prepared by Sol-Gel method to study their dielectric characteristics and electric conductivities through X-ray photoelectron spectrum （XPS）. The results showed that the dielectric characteristics of Nd2O3 doped BaTiO3 ceramics were improved by doping. When Nd2O3 content was 0.003 mol, the results were even better, the dielectric constant was increased, the dielectric loss was decreased, the Curie-temperature （Tc） was 110 ℃, and the frequency characteristic was also good. The resistivity of Nd2O3 doped BaTiO3 ceramics was lower than that of pure BaTiO3 ceramics, when Nd2O3 content was 0.001 mol,the resistivity was （2.364×）108 Ω·m, the smallest. The grain resistance of Nd2O3 doped BaTiO3 ceramics exhibited NTC effect, but the grain boundary resistance showed PTC effect, and the grain boundary resistance was larger than that of the grain resistance, so the PTC effect originated from the grain boundary. The analysis of the element binding energy through X-ray photoelectron spectrum were indicated that the quantivalence of Ba2+and Ti4+in Nd2O3 doped BaTiO3 ceramics was variable, and resulted in the improvement of the conductibility of BaTiO3 ceramics.展开更多
Al_(2)O_(3)/SiC composite ceramics were prepared fromα-Al_(2)O_(3) and SiC by a pressureless sinter method in this study.The effect of SiC contents on the mechanic properties,phase compositions and microstructure is ...Al_(2)O_(3)/SiC composite ceramics were prepared fromα-Al_(2)O_(3) and SiC by a pressureless sinter method in this study.The effect of SiC contents on the mechanic properties,phase compositions and microstructure is studied.Experimental results show that the vickers hardness,wear resistance and thermal conductivity of the samples increase with the increase in the SiC content,and the hardness of the sample reaches 16.22 GPa,and thermal conductivity of the sample reaches 25.41 W/(m.K)at room temperature when the SiC content is 20 wt%(B5)and the sintering temperature is at 1640℃.Higher hardness means higher scour resistance,and it indicates that the B5 material is expected to be used for the solar heat absorber of third generation solar thermal generation.The results indicate the mechanism of improving mechanical properties of Al_(2)O_(3)/SiC composite ceramics:SiC plays a role in grain refinement that the grain of SiC inhibits the grain growth of Al_(2)O_(3),while the addition of SiC changes the fracture mode from the intergranular to the intergranular-transgranular.展开更多
Ceramic composites Al_2O_3/(W, Ti)C/Cr_3C_2 with different contents of Cr_3C_2 and (W, Ti)C particles, and with the additive Y_2O_3, were fabricated with hot-pressing technique at 1700 ℃ under 28 MPa pressure for 30 ...Ceramic composites Al_2O_3/(W, Ti)C/Cr_3C_2 with different contents of Cr_3C_2 and (W, Ti)C particles, and with the additive Y_2O_3, were fabricated with hot-pressing technique at 1700 ℃ under 28 MPa pressure for 30 min in N_2 atmosphere. The mechanical properties were tested, and the microstructure was investigated by environment scanning electron microscope (ESEM), transmission electron microscope (TEM), energy dispersive analysis using X-ray (EDAX) and optical microscope (OM). Results indicate that the incorporation of Cr_3C_2 and (W,Ti)C particles can suppress the grain growth of the others, and the toughening and strengthening effects mainly originate from nano-particles, dispersion toughening and solidification strengthening. The multiphase composite ceramic material Al_2O_3/10%Cr_3C_2/20%(W,Ti)C shows good mechanical properties, especially the fracture toughness increases from 4.0 MPa·m 1/2 (Monolithic Al_2O_3 ceramic) to 8.92 MPa·m 1/2, the flexural strength from 260～340 MPa (Monolithic Al_2O_3 ceramic) to 496 MPa, due to incorporation of the suitable contents of Cr_3C_2 and (W,Ti)C particles.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.12172179,U2341244,and 11772160)。
文摘To enhance the protective performance of ceramic composite armor,ballistic penetration experiments were conducted on Al_(2)O_(3) ceramic-ultra-high molecular weight polyethylene(UHMWPE)composite armor with different thickness configurations.The damage and failure modes of hard projectiles and ceramic-fiber composite targets were analyzed.The recovered projectiles and ceramic fragments were sieved and weighed at multiple stages,revealing a positive correlation between the degree of fragmentation of the projectiles and ceramics and the overall ballistic resistance of the composite targets.Numerical simulations were performed using the LS-DYNA finite element software,and the simulation results showed high consistency with the experimental results,confirming the validity of the material parameters.The results indicate that the projectile heads primarily exhibited crushing and abrasive fragmentation.Larger projectile fragments mainly resulted from tensile and shear stress-induced failure.The failure modes of the composite targets included the formation of ceramic cones and radial cracks under high-velocity impacts.The UHMWPE laminated plates exhibited interlayer separation caused by tensile waves,permanent plastic deformation of the rear surface bulging,and perforation failure primarily due to shear forces.Through extended numerical simulations,while maintaining the same areal density and configuration of9 mm Al_(2)O_(3) ceramic+12 mm UHMWPE laminated composite armor,the thickness configurations of the Al_(2)O_(3) ceramic and UHMWPE laminated backplates were varied,and various thicknesses of UHMWPE laminates were simulated as the cover layer for the ceramic panels.The simulation results indicated that the composite armor configuration of 10 mm Al_(2)O_(3) ceramic+8 mm UHMWPE composite armor increased energy absorption by13.48%.When altering the cover layer thickness,a 4 mm UHMWPE+9 mm Al_(2)O_(3)+8 mm UHMWPE composite armor demonstrated a 27.11%improvement in energy absorption,showing a relatively significant enhancement.
基金This work was financially supported by the Shandong Provincial Natural Science Foundation(ZR2020QB116)the Excellent Young Talents Foundation in Universities of Anhui Province(gxyq2021223)the Key Research Project of Natural Science in Universities of Anhui Province.(KJ2020A0749).
文摘Superwetting materials have drawn unprecedented attention in the treatment of oily wastewater due to their preferable anti-fouling property and selective oil/water separation.However,it is still a challenge to fabricate multifunctional and environmentally friendly materials,which can be stably applied to purify the actual complicated wastewater.Here,a Ag/Ag/α-Fe_(2)O_(3) heterostructure anchored copper mesh was intentionally synthesized using a facile two-step hydrothermal method.The resultant mesh with superhydrophilicity and underwater superoleophobicity was capable of separating various oil/water mixtures with superior separation efficiency and high permeationflux driven by gravity.Benefiting from the joint effects of the smaller band gap of Ag/α-Fe_(2)O_(3) heterojunction,inherent antibacterial capacity of Ag/α-Fe_(2)O_(3) and Ag nanoparticles,favorable conductive substrate,as well as the hierarchical structure with superwettability,such mesh presented remarkably enhanced degradation capability toward organic dyes under visible light irradiation and antibacterial activity against both Escherichia coli(E.coli)and Staphylococcus aureus(S.aureus)compared with the pure Ag/α-Fe_(2)O_(3) coated mesh.Impressively,the mesh exhibited bifunctional water purification performance,in which organic dyes were eliminated simultaneously from water during oil/water separation in onefiltration process.More importantly,this mesh behaved exceptional chemical resistance,mechanical stability and long-term reusability.Therefore,this material with multifunctional integration may hold promising potential for steady water purification in practice.
文摘Nd2O3 doped BaTiO3ceramics（the additive content was respectively 0.001, 0.002, 0.003, 0.005, 0.01 molar ratio）were prepared by Sol-Gel method to study their dielectric characteristics and electric conductivities through X-ray photoelectron spectrum （XPS）. The results showed that the dielectric characteristics of Nd2O3 doped BaTiO3 ceramics were improved by doping. When Nd2O3 content was 0.003 mol, the results were even better, the dielectric constant was increased, the dielectric loss was decreased, the Curie-temperature （Tc） was 110 ℃, and the frequency characteristic was also good. The resistivity of Nd2O3 doped BaTiO3 ceramics was lower than that of pure BaTiO3 ceramics, when Nd2O3 content was 0.001 mol,the resistivity was （2.364×）108 Ω·m, the smallest. The grain resistance of Nd2O3 doped BaTiO3 ceramics exhibited NTC effect, but the grain boundary resistance showed PTC effect, and the grain boundary resistance was larger than that of the grain resistance, so the PTC effect originated from the grain boundary. The analysis of the element binding energy through X-ray photoelectron spectrum were indicated that the quantivalence of Ba2+and Ti4+in Nd2O3 doped BaTiO3 ceramics was variable, and resulted in the improvement of the conductibility of BaTiO3 ceramics.
基金Funded by the National Key Technology Research and Development Program of the Ministry of Science and Technology of China(No.2018YFB1501002)。
文摘Al_(2)O_(3)/SiC composite ceramics were prepared fromα-Al_(2)O_(3) and SiC by a pressureless sinter method in this study.The effect of SiC contents on the mechanic properties,phase compositions and microstructure is studied.Experimental results show that the vickers hardness,wear resistance and thermal conductivity of the samples increase with the increase in the SiC content,and the hardness of the sample reaches 16.22 GPa,and thermal conductivity of the sample reaches 25.41 W/(m.K)at room temperature when the SiC content is 20 wt%(B5)and the sintering temperature is at 1640℃.Higher hardness means higher scour resistance,and it indicates that the B5 material is expected to be used for the solar heat absorber of third generation solar thermal generation.The results indicate the mechanism of improving mechanical properties of Al_(2)O_(3)/SiC composite ceramics:SiC plays a role in grain refinement that the grain of SiC inhibits the grain growth of Al_(2)O_(3),while the addition of SiC changes the fracture mode from the intergranular to the intergranular-transgranular.
文摘Ceramic composites Al_2O_3/(W, Ti)C/Cr_3C_2 with different contents of Cr_3C_2 and (W, Ti)C particles, and with the additive Y_2O_3, were fabricated with hot-pressing technique at 1700 ℃ under 28 MPa pressure for 30 min in N_2 atmosphere. The mechanical properties were tested, and the microstructure was investigated by environment scanning electron microscope (ESEM), transmission electron microscope (TEM), energy dispersive analysis using X-ray (EDAX) and optical microscope (OM). Results indicate that the incorporation of Cr_3C_2 and (W,Ti)C particles can suppress the grain growth of the others, and the toughening and strengthening effects mainly originate from nano-particles, dispersion toughening and solidification strengthening. The multiphase composite ceramic material Al_2O_3/10%Cr_3C_2/20%(W,Ti)C shows good mechanical properties, especially the fracture toughness increases from 4.0 MPa·m 1/2 (Monolithic Al_2O_3 ceramic) to 8.92 MPa·m 1/2, the flexural strength from 260～340 MPa (Monolithic Al_2O_3 ceramic) to 496 MPa, due to incorporation of the suitable contents of Cr_3C_2 and (W,Ti)C particles.
