The Mechanism of Cube Texture Formation in Ni-7 at%W Substrate

In order to obtain the sharp cube texture,a new process,the intermediate annealing rolling technique,has been introduced to prepare the Ni7W substrate.In this paper,a cubic texture content up to 98.5%within 10°of the standard cubic orientation is obtained in the final substrate and the influence of this improved rolling technique on the cube texture formation has been discussed.The results show that the increased cube texture in the Ni7W substrate is caused by the optimized deformation texture and the increased nucleated fraction of the cube grains.

Achieving high ductility and low in-plane anisotropy in magnesium alloy through a novel texture design strategy

Texture regulation is a prominent method to modify the mechanical properties and anisotropy of magnesium alloy.In this work,the Mg-1Al-0.3Ca-0.5Mn-0.2Gd(wt.%)alloy sheet with TD-tilted and circular texture was fabricated by unidirectional rolling(UR)and multidirectional rolling(MR)method,respectively.Unlike generating a strong in-plane mechanical anisotropy in conventional TD-tilted texture,the novel circular texture sample possessed a weak in-plane yield anisotropy.This can be rationalized by the similar proportion of soft grains with favorable orientation for basalslip and{10.12}tensile twinning during the uniaxial tension of circular-texture sample along different directions.Moreover,compared with the TD-tilted texture,the circular texture improved the elongation to failure both along the rolling direction(RD)and transverse direction(TD).By quasi-in-situ EBSD-assisted slip trace analysis,higher activation of basal slip was observed in the circular-texture sample during RD tension,contributing to its excellent ductility.When loading along the TD,the TD-tilted texture promoted the activation of{10.12}tensile twins significantly,thus providing nucleation sites for cracks and deteriorating the ductility.This research may shed new insights into the development of formable and ductile Mg alloy sheets by texture modification.

A texture-modified dessert with high nutritional value designed for people with dysphagia:effect of refrigeration and frozen storage

Dysphagia is commonly associated with malnutrition and an increased choking risk.To overcome these complications,food designed for people with dysphagia should have an appropriate texture and a high nutritional value.In this study,six formulations of a strawberry dessert enriched in protein(calcium caseinate)and fiber(wheat dextrin or inulin)were developed using different hydrocolloids(xanthan gum,carboxymethyl cellulose or modified starch)to provide desirable texture and stability.Nutritional value was calculated and total phenolic content and antioxidant activity of the samples were analyzed.Back-extrusion test,rheological measurements and sensory analysis were performed in refrigerated and frozen samples to characterize their textural and viscoelastic properties.The high content in protein(14.7 g/100 g)and fiber(7.9-8.7 g/100 g)made possible to use the claims“high protein”and“high fiber”.Phytochemicals supplied by strawberries contributed to the antioxidant properties of the dessert.Loss tangent ranged 0.28-0.35 for all the formulations,indicating a weak gel behavior,which could be considered safe to swallow.The formulations with dextrin in combination with carboxymethyl cellulose or xanthan gum seemed to be less susceptible to structural changes during frozen storage.This work provides insights for the development of a nutrient-dense dessert that meets the requirements of people with dysphagia.

Evolution of microstructure and texture of AZ80 magnesium alloy under hot torsion with constant decreasing temperature rate

Hot torsion tests for AZ80 magnesium alloy were carried out in the temperature range of 380℃-260℃,with a constant decreasing temperature rate of 10℃/s in order to weaken the basal texture and refine the grains.The results indicated that the average grain sizes were refined forming gradient structure with increasing specimen radial position from center(12.2-5.4μm),and that the initial basal texture intensity of the extruded magnesium alloy was weakened from 46.2 to 8.3.Furthermore,the extension twins(ETs)could be disintegrated from the twins forming separated twins with smaller sizes.Interestingly,ETs with the same twin variant intersecting with each other could be coalesced forming grains with similar orientation,while ETs with different twin variants were separated by twins boundaries contributing to grain refinement.Moreover,in addition to the conventional continuous dynamic recrystallized(CDRX)grains with 30˚orientation rotated around C-axis of the parent grains,CDRXed grains with 30˚rotation around a-axis and random rotation axis were also discerned.Besides,the CDRX evolution induced twins were also elaborated,exhibiting the complex competition between CDRX and twining.Hot torsion deformation with constant decreasing temperatures rate is an effective way of grain refinement and texture modification.

Unveiling the rolling texture variations ofα-Mg phases in a dual-phase Mg-Li alloy

LZ91 Mg-Li alloy plates with three types of initial texture were rolled by 70%reduction at both room temperature and 200℃to explore the rolling texture formation ofα-Mg phase.The results showed that the rolling texture is largely affected by the initial texture.All the samples exhibited two main texture components as RD-split double peaks texture and TD-split double peaks texture after large strain rolling.The intensity of the two texture components was strongly influenced by the initial orientation and rolling temperature.Extension twinning altered the large-split non-basal orientation to a near basal one at low rolling strain.The basal orientation induced by twinning is unstable,which finally transmitted to the RD-split texture.The strong TD-split texture formed due to slip-induced orientation transition from its initial orientation.The competition between prismatic and basal slip determined the intensity and tilt angle of the TD-split texture.By increasing the rolling temperature,the TD-split texture component was enhanced in all three samples.Limitation of extension twinning behavior and the promotion of prismatic slip at elevated temperature are the main reasons for the difference in hot and cold rolling texture.

On dry machining of AZ31B magnesium alloy using textured cutting tool inserts

Magnesium alloys have many advantages as lightweight materials for engineering applications,especially in the fields of automotive and aerospace.They undergo extensive cutting or machining while making products out of them.Dry cutting,a sustainable machining method,causes more friction and adhesion at the tool-chip interface.One of the promising solutions to this problem is cutting tool surface texturing,which can reduce tool wear and friction in dry cutting and improve machining performance.This paper aims to investigate the impact of dimple textures(made on the flank face of cutting inserts)on tool wear and chip morphology in the dry machining of AZ31B magnesium alloy.The results show that the cutting speed was the most significant factor affecting tool flank wear,followed by feed rate and cutting depth.The tool wear mechanism was examined using scanning electron microscope(SEM)images and energy dispersive X-ray spectroscopy(EDS)analysis reports,which showed that at low cutting speed,the main wear mechanism was abrasion,while at high speed,it was adhesion.The chips are discontinuous at low cutting speeds,while continuous at high cutting speeds.The dimple textured flank face cutting tools facilitate the dry machining of AZ31B magnesium alloy and contribute to ecological benefits.

Tailoring the texture and mechanical properties of 3%Y_(2)O_(3)p/ZGK200 composites fabricated by unidirectional and cross rolling followed by annealing

3%Y_(2)O_(3)p/ZGK200 composites were subjected to unidirectional rolling(UR)and cross rolling(CR)at 400℃and 350℃followed by annealing at 300℃for 1 h.The microstructure,texture and mechanical properties of rolled and annealed composites were systematically studied.The rolled composites exhibited a heterogeneous microstructure,consisting of deformed grains elongated along rolling direction(RD)and Y_(2)O_(3)particles bands distributed along RD.After annealing,static recrystallization(SRX)occurred and most deformed grains transformed into equiaxed grains.A non-basal texture with two strong T-texture components was obtained after UR while a non-basal elliptical/circle texture with circle multi-peaks was obtained after CR,indicating that rolling path had great influences on texture of the composites.After annealing process,R-texture component disappeared or weakened,as results,a non-basal texture with double peaks tilting from normal direction(ND)to transverse direction(TD)and a more random non-basal texture with circle multi-peaks were obtained for UR and CR composites,respectively.The yield strength of rolled composites after UR showed obvious anisotropy along RD and TD while a low anisotropic yield strength was obtained after CR.Some Y_(2)O_(3)particles broke during rolling.The fracture of the composites was attributed to the existence of Y_(2)O_(3)clusters and interfacial debonding between particles and matrix during tension,as a result,the ductility was not as superior as matrix alloy.

Automatic area estimation of algal blooms in water bodies from UAV images using texture analysis

Algal blooms,the spread of algae on the surface of water bodies,have adverse effects not only on aquatic ecosystems but also on human life.The adverse effects of harmful algal blooms(HABs)necessitate a convenient solution for detection and monitoring.Unmanned aerial vehicles(UAVs)have recently emerged as a tool for algal bloom detection,efficiently providing on-demand images at high spatiotemporal resolutions.This study developed an image processing method for algal bloom area estimation from the aerial images(obtained from the internet)captured using UAVs.As a remote sensing method of HAB detection,analysis,and monitoring,a combination of histogram and texture analyses was used to efficiently estimate the area of HABs.Statistical features like entropy(using the Kullback-Leibler method)were emphasized with the aid of a gray-level co-occurrence matrix.The results showed that the orthogonal images demonstrated fewer errors,and the morphological filter best detected algal blooms in real time,with a precision of 80%.This study provided efficient image processing approaches using on-board UAVs for HAB monitoring.

Effect of forging on the microstructure and texture of a high Nb containing γ-TiAl alloy

The effect of forging on the microstructure and texture evolution of a high Nb containing Ti-45Al-7Nb-0.3W(at.%)alloy was investigated by X-ray diffractometer(XRD),scanning electron microscopy(SEM),and transmission electron microscopy(TEM).The results show that the as-cast alloy is mainly composed of α_(2)/γ lamellar colonies with a mean size of 70μm,but the hot-forged pancake displays a near duplex microstructure(DP).Kinking and bending of lamellar colonies,deformation twinning and dynamic recrystallization(DRX)occur during hot forging.Meanwhile,dense dislocations in theβphase after forging suggest that the high-temperature β phase with a disordered structure is favorable for improving the hot-workability of the alloy.Unlike the common TiAl casting texture,the solidification process of the investigated as-cast alloy with high Nb content is completely via the β phase region,resulting in the formation of a<110>γ fiber texture where the<110>γ aligns parallel to the heat-flow direction.In comparison,the relatively strong<001>and weak<302>texture components in the as-forged alloy are attributed to the deformation twinning.After annealing,static recrystallization occurs at the twin boundary and intersections,which weakens the deformation texture.

The Clinical Value of Ultrasound Image Texture Analysis in the Diagnosis of Uterine Adhesions

Purpose: This review examines the diagnostic value of transvaginal 3D ultrasound image texture analysis for the diagnosis of uterine adhesions. Materials and Methods: The total clinical data of 53 patients with uterine adhesions diagnosed by hysteroscopy and the imaging data of transvaginal three-dimensional ultrasound from the Second Affiliated Hospital of Chongqing Medical University from June 2022 to August 2023 were retrospectively analysed. Based on hysteroscopic surgical records, patients were divided into two independent groups: normal endometrium and uterine adhesion sites. The samples were divided into a training set and a test set, and the transvaginal 3D ultrasound was used to outline the region of interest (ROI) and extract texture features for normal endometrium and uterine adhesions based on hysteroscopic surgical recordings, the training set data were feature screened and modelled using lasso regression and cross-validation, and the diagnostic efficacy of the model was assessed by applying the subjects’ operating characteristic (ROC) curves. Results: For each group, 290 texture feature parameters were extracted and three higher values were screened out, and the area under the curve of the constructed ultrasonographic scoring model was 0.658 and 0.720 in the training and test sets, respectively. Conclusion Relative clinical value of transvaginal three-dimensional ultrasound image texture analysis for the diagnosis of uterine adhesions.

Application of texture signatures based on multiparameter-magnetic resonance imaging for predicting microvascular invasion in hepatocellular carcinoma:Retrospective study

BACKGROUND Despite continuous changes in treatment methods,the survival rate for advanced hepatocellular carcinoma(HCC)patients remains low,highlighting the importance of diagnostic methods for HCC.AIM To explore the efficacy of texture analysis based on multi-parametric magnetic resonance(MR)imaging(MRI)in predicting microvascular invasion(MVI)in preoperative HCC.METHODS This study included 105 patients with pathologically confirmed HCC,categorized into MVI-positive and MVI-negative groups.We employed Original Data Analysis,Principal Component Analysis,Linear Discriminant Analysis(LDA),and Non-LDA(NDA)for texture analysis using multi-parametric MR images to predict preoperative MVI.The effectiveness of texture analysis was determined using the B11 program of the MaZda4.6 software,with results expressed as the misjudgment rate(MCR).RESULTS Texture analysis using multi-parametric MRI,particularly the MI+PA+F dimensionality reduction method combined with NDA discrimination,demonstrated the most effective prediction of MVI in HCC.Prediction accuracy in the pulse and equilibrium phases was 83.81%.MCRs for the combination of T2-weighted imaging(T2WI),arterial phase,portal venous phase,and equilibrium phase were 22.86%,16.19%,20.95%,and 20.95%,respectively.The area under the curve for predicting MVI positivity was 0.844,with a sensitivity of 77.19%and specificity of 91.67%.CONCLUSION Texture analysis of arterial phase images demonstrated superior predictive efficacy for MVI in HCC compared to T2WI,portal venous,and equilibrium phases.This study provides an objective,non-invasive method for preoperative prediction of MVI,offering a theoretical foundation for the selection of clinical therapy.

Two-stage dynamic recrystallization and texture evolution in Al-7Mg alloy during hot torsion

Hot torsion tests were performed on the Al-7Mg alloy at the temperature ranging from 300 to 500℃ and strain rates between 0.05 and 5 s^(-1) to explore the progressive dynamic recrystallization(DRX)and texture behaviors.The DRX behavior of the alloy manifested two distinct stages:Stage 1 at strain of≤2 and Stage 2 at strains of≥2.In Stage 1,there was a slight increase in the DRXed grain fraction(X_(DRX))with predominance of discontinuous DRX(DDRX),followed by a modest change in X_(DRX) until the transition to Stage 2.Stage 2 was marked by an accelerated rate of DRX,culminating in a substantial final X_(DRX) of~0.9.Electron backscattered diffraction(EBSD)analysis on a sample in Stage 2 revealed that continuous DRX(CDRX)predominantly occurred within the(121)[001]grains,whereas the(111)[110]grains underwent a geometric DRX(GDRX)evolution without a noticeable sub-grain structure.Furthermore,a modified Avrami’s DRX kinetics model was utilized to predict the microstructural refinement in the Al-7Mg alloy during the DRX evolution.Although this kinetics model did not accurately capture the DDRX behavior in Stage 1,it effectively simulated the DRX rate in Stage 2.The texture index was employed to assess the evolution of the texture isotropy during hot-torsion test,demonstrating significant improvement(>75%)in texture randomness before the commencement of Stage 2.This initial texture evolution is attributed to the rotation of parent grains and the substructure evolution,rather than to an increase in X_(DRX).

A new two-step variational model for multiplicative noise removal with applications to texture images

Multiplicative noise removal problems have attracted much attention in recent years.Unlike additive noise,multiplicative noise destroys almost all information of the original image,especially for texture images.Motivated by the TV-Stokes model,we propose a new two-step variational model to denoise the texture images corrupted by multiplicative noise with a good geometry explanation in this paper.In the first step,we convert the multiplicative denoising problem into an additive one by the logarithm transform and propagate the isophote directions in the tangential field smoothing.Once the isophote directions are constructed,an image is restored to fit the constructed directions in the second step.The existence and uniqueness of the solution to the variational problems are proved.In these two steps,we use the gradient descent method and construct finite difference schemes to solve the problems.Especially,the augmented Lagrangian method and the fast Fourier transform are adopted to accelerate the calculation.Experimental results show that the proposed model can remove the multiplicative noise efficiently and protect the texture well.

Low-fat microwaved peanut snacks production:Effect of defatting treatment on structural characteristics,texture,color,and nutrition

This study develops low-fat microwaved peanut snacks(LMPS)using partially defatted peanuts(PDP)with different defatting ratios,catering to people’s pursuit of healthy,low-fat cuisine.The effects of defatting treatment on the structural characteristics,texture,color,and nutrient composition of LMPS were comprehensively explored.The structural characteristics of LMPS were characterized using X-ray micro-computed tomography(Micro-CT)and scanning electron microscope(SEM).The results demonstrated that the porosity,pore number,pore volume,brightness,brittleness,protein content,and total sugar content of LMPS all significantly increased(P<0.05)with the increase in the defatting ratio.At the micro level,porous structure,cell wall rupture,and loss of intracellular material could be observed in LMPS after defatting treatments.LMPS made from PDP with a defatting ratio of 64.44%had the highest internal pore structural parameters(porosity 59%,pore number 85.3×10^(5),pore volume 68.23 mm3),the brightest color(L^(*) 78.39±0.39),the best brittleness(3.64±0.21)mm^(–1)),and the best nutrition(high protein content,(34.02±0.38)%;high total sugar content,(17.45±0.59)%;low-fat content,(27.58±0.85)%).The study provides a theoretical basis for the quality improvement of LMPS.

Robust Machine Learning Technique to Classify COVID-19 Using Fusion of Texture and Vesselness of X-Ray Images

Manual investigation of chest radiography(CXR)images by physicians is crucial for effective decision-making in COVID-19 diagnosis.However,the high demand during the pandemic necessitates auxiliary help through image analysis and machine learning techniques.This study presents a multi-threshold-based segmentation technique to probe high pixel intensity regions in CXR images of various pathologies,including normal cases.Texture information is extracted using gray co-occurrence matrix(GLCM)-based features,while vessel-like features are obtained using Frangi,Sato,and Meijering filters.Machine learning models employing Decision Tree(DT)and RandomForest(RF)approaches are designed to categorize CXR images into common lung infections,lung opacity(LO),COVID-19,and viral pneumonia(VP).The results demonstrate that the fusion of texture and vesselbased features provides an effective ML model for aiding diagnosis.The ML model validation using performance measures,including an accuracy of approximately 91.8%with an RF-based classifier,supports the usefulness of the feature set and classifier model in categorizing the four different pathologies.Furthermore,the study investigates the importance of the devised features in identifying the underlying pathology and incorporates histogrambased analysis.This analysis reveals varying natural pixel distributions in CXR images belonging to the normal,COVID-19,LO,and VP groups,motivating the incorporation of additional features such as mean,standard deviation,skewness,and percentile based on the filtered images.Notably,the study achieves a considerable improvement in categorizing COVID-19 from LO,with a true positive rate of 97%,further substantiating the effectiveness of the methodology implemented.

Evaluation of Textured Concrete as an Alternative for Stone as a Cladding Material

Along with the increasing demand on exterior wall cladding as a protective cover for the interior elements and an indicator for modernity and architectural innovation,comes the need to develop new cladding materials that can replace the old ones and overcome their setbacks.This paper discusses the possibility of replacing stone by textured concrete as a cladding material in order to overcome the main challenges faced stone cladding by comparing them together.The comparison was made based on the main requirements of the cladding materials namely:economic,environmental,social,functional and structural aspects.

Topic highlight on texture and color enhancement imaging in gastrointestinal diseases

Olympus Corporation developed texture and color enhancement imaging(TXI)as a novel image-enhancing endoscopic technique.This topic highlights a series of hot-topic articles that investigated the efficacy of TXI for gastrointestinal disease identification in the clinical setting.A randomized controlled trial demonstrated improvements in the colorectal adenoma detection rate(ADR)and the mean number of adenomas per procedure(MAP)of TXI compared with those of white-light imaging(WLI)observation(58.7%vs 42.7%,adjusted relative risk 1.35,95%CI:1.17-1.56;1.36 vs 0.89,adjusted incident risk ratio 1.48,95%CI:1.22-1.80,respectively).A cross-over study also showed that the colorectal MAP and ADR in TXI were higher than those in WLI(1.5 vs 1.0,adjusted odds ratio 1.4,95%CI:1.2-1.6;58.2%vs 46.8%,1.5,1.0-2.3,respectively).A randomized controlled trial demonstrated non-inferiority of TXI to narrow-band imaging in the colorectal mean number of adenomas and sessile serrated lesions per procedure(0.29 vs 0.30,difference for non-inferiority-0.01,95%CI:-0.10 to 0.08).A cohort study found that scoring for ulcerative colitis severity using TXI could predict relapse of ulcerative colitis.A cross-sectional study found that TXI improved the gastric cancer detection rate compared to WLI(0.71%vs 0.29%).A cross-sectional study revealed that the sensitivity and accuracy for active Helicobacter pylori gastritis in TXI were higher than those of WLI(69.2%vs 52.5%and 85.3%vs 78.7%,res-pectively).In conclusion,TXI can improve gastrointestinal lesion detection and qualitative diagnosis.Therefore,further studies on the efficacy of TXI in clinical practice are required.

Rolling texture development in a dual-phase Mg-Li alloy:The role of temperature

Dual-phase Mg-Li alloys sheets were rolled at four different temperatures ranging from liquid nitrogen to 300℃to explore effect of rolling temperature on texture and mechanical properties of the material.Crystal plasticity simulation was utilized to illustrate the influence of slip activity on rolling texture development.The results show that the rolling texture is largely depended on deformation temperature.Unlike commercial Mg alloys,the critical resolved shear stress of basal slip inα-Mg phase of Mg-Li alloy decreased more significantly by increasing temperature compared to that of pyramidal<c+a>slip.Enhancement of basal slip by increasing temperature triggered a decrease of split angle of basal poles for the double-peak texture.Prismaticslip largely enhanced by increasing temperature upon 200℃,which induced a wider orientation spread along the transverse direction.For theβ-Li phase,the promotion of{110}<111>slip system at elevated temperature triggered the enhancement of{211}<110>and{111}<211>texture components.The cryo-rolled sample exhibited the highest strength compared to the others due to a strong hardening behavior at this temperature.A two-stage hardening behavior was observed in these as-rolled dual-phase alloys.Strain transition at phase boundaries could be the reason for appearance of this two-stage hardening.

Towards tailoring basal texture of rolled Mg alloy sheet by recrystallization for high room-temperature formability: A review

Room-temperature(RT) formability is a key factor to broaden the applications of rolled Mg alloy sheets in the industry. However, rolled Mg alloy sheets generally form strong basal texture, where the(0001) poles align parallel to the normal direction(ND). This hinders the activation of(0001) [1120] basal slip, limiting the RT formability. Therefore, texture weakening, i.e., the inclination of the(0001) poles from the ND, plays an important role to improve the RT formability. Recrystallization is crucial to control the textural development in Mg,and currently, the texture weakening is commonly achieved using static recrystallization(SRX). However, the type of slipping and twinning,which are activated during rolling, affect the textural features after SRX. It is also demonstrated that shear bands and preferential grain growth are important factors to tailor the texture during SRX. Indeed, dynamic recrystallization(DRX) easily occurs during rolling in Mg, which also affects the final rolling texture, while the effect of DRX on the textural formation is not extensively studied for the development of RT-formable Mg alloy sheets. Therefore, the effect of these factors on the textural development in rolled Mg is reviewed in this manuscript.Additionally, the ideal microstructure and texture for RT-formable Mg alloy sheets are still controversial. The RT-formability includes stretch forming(biaxial tension), bending(plane strain tension), and deep-drawing. In particular, the stretch forming is commonly used to evaluate the RT-formability of rolled Mg. Although the stretch formability has been improved by recent studies, the further improvement is necessary owing to the relatively low formability of rolled Mg compared with that of rolled Fe and Al. Based on the relationship between the microstructure/texture and stretch formability provided in the literature, the design guidance for high stretch formability is proposed in this review.

Laser additive manufacturing of zinc:formation quality,texture,and cell behavior

Laser powder bed fusion(LPBF)makes it possible for biodegradable zinc(Zn)to be used to produce customized orthopedic implants.In this research,we investigate the impact of laser power and scanning speed on the development of surface quality,relative densification,and texture during LPBF of Zn implants.Increasing laser power was able to decrease melt viscosity and surface tension,which improved the metallurgical bonding between adjacent tracks.Uneven and twisted tracks also became continuous and straight.Scanning speed could controlmolten-pool temperature to restrain grain natural orientation,achieving various crystal orientations and a weakened texture.Importantly,it further avoided the thermal expansion and contraction caused by excessive energy storage and accumulation in the matrix,thus reducing the generation of high-dislocation density.As a result,by selecting a reasonable laser power and scanning speed,the LPBF parts exhibited a flat surface morphology and a high density over 99.5%.Their average hardness,mechanical strength,and elongation reached 50.2 HV,127.8 MPa,and 7.6%,respectively.Additionally,the parts displayed a moderate degradation rate and excellent osteogenic properties.All these results provide a basis for selecting process parameters to optimize the comprehensive properties of LPBF-processed Zn parts for biodegradable applications.