Optimized calculations of 75 PCDDs and their parent DD were carded out at the B3LYP/6-31G＊ level by density functional theory （DFT） method. The structural parameters were obtained and significant correlation betwee...Optimized calculations of 75 PCDDs and their parent DD were carded out at the B3LYP/6-31G＊ level by density functional theory （DFT） method. The structural parameters were obtained and significant correlation between the C1 substitution position and some structural parameters was found. Consequently, the number of C1 substitution positions was taken as theoretical descriptors to establish two novel QSPR models for predicting lgKow and -lgSw of all PCDD congeners. The two models achieved in this work contain two variables （Na and Nβ）, of which r = 0.9312, 0.9965 and SD = 0.27, 0.12 respectively, and t values are all large. The variation inflation factors （VIF） of variables in the two models herein are both less than 5.0, suggesting high accuracy of the lgKow and -lgSw predicting models, and the results of cross-validation test also show that the two models exhibit optimum stability and good predictive power. By comparison, the correlation and predictive ability of the present work are more advantageous than those obtained using semi-empirical AM1 and GC-RI methods.展开更多
The Taguchi method was used to obtain the optimum electrodeposition parameters for the synthesis of the CuInSe2 thin film for solar cells. The parameters consist of annealing temperature, current density, CuCl2 concen...The Taguchi method was used to obtain the optimum electrodeposition parameters for the synthesis of the CuInSe2 thin film for solar cells. The parameters consist of annealing temperature, current density, CuCl2 concentration, FeCl3 concentration, H2SeO3 concentration, TEA amount, pH value, and deposition time. The experiments were carried out according to an L18（2^13^7） table An X-ray diffractometer （XRD） and a scanning electron microscope （SEM） were respectively used to analyze the phases and observe the microstructure and the grain size of the CuInSe2 film before and after annealing treatment. The results showed that the CuInSe2 phase was deposited with a preferred plane （112） parallel to the substrate surface. The optimum parameters are as follows： current density, 7 mA/cm^2; CuCl2 concentration, 10 mM; FeCl3 concentration, 50 mM; H2SeO3 concentration, 15 mM; TEA amount, 0 mL; pH value, 1.65; deposition time, 10 min; and annealing temperature, 500℃.展开更多
基金This work was supported by the National Natural Science Foundation of China (No. 20737001)(2003CB415002)China Postdoctoral Science Foundation (No. 2003033486)
文摘Optimized calculations of 75 PCDDs and their parent DD were carded out at the B3LYP/6-31G＊ level by density functional theory （DFT） method. The structural parameters were obtained and significant correlation between the C1 substitution position and some structural parameters was found. Consequently, the number of C1 substitution positions was taken as theoretical descriptors to establish two novel QSPR models for predicting lgKow and -lgSw of all PCDD congeners. The two models achieved in this work contain two variables （Na and Nβ）, of which r = 0.9312, 0.9965 and SD = 0.27, 0.12 respectively, and t values are all large. The variation inflation factors （VIF） of variables in the two models herein are both less than 5.0, suggesting high accuracy of the lgKow and -lgSw predicting models, and the results of cross-validation test also show that the two models exhibit optimum stability and good predictive power. By comparison, the correlation and predictive ability of the present work are more advantageous than those obtained using semi-empirical AM1 and GC-RI methods.
文摘The Taguchi method was used to obtain the optimum electrodeposition parameters for the synthesis of the CuInSe2 thin film for solar cells. The parameters consist of annealing temperature, current density, CuCl2 concentration, FeCl3 concentration, H2SeO3 concentration, TEA amount, pH value, and deposition time. The experiments were carried out according to an L18（2^13^7） table An X-ray diffractometer （XRD） and a scanning electron microscope （SEM） were respectively used to analyze the phases and observe the microstructure and the grain size of the CuInSe2 film before and after annealing treatment. The results showed that the CuInSe2 phase was deposited with a preferred plane （112） parallel to the substrate surface. The optimum parameters are as follows： current density, 7 mA/cm^2; CuCl2 concentration, 10 mM; FeCl3 concentration, 50 mM; H2SeO3 concentration, 15 mM; TEA amount, 0 mL; pH value, 1.65; deposition time, 10 min; and annealing temperature, 500℃.
