In this work, the field plate termination is studied for Ga2O3Schottky barrier diodes(SBDs) by simulation. The influence of field plate overlap, dielectric material and thickness on the termination electric field dist...In this work, the field plate termination is studied for Ga2O3Schottky barrier diodes(SBDs) by simulation. The influence of field plate overlap, dielectric material and thickness on the termination electric field distribution are demonstrated.It is found that the optimal thickness increases with reverse bias increasing for all the three dielectrics of SiO2, Al2O3, and HfO2. As the thickness increases, the maximum electric field intensity decreases in SiO2and Al2O3, but increases in HfO2.Furthermore, it is found that SiO2and HfO2are suitable for the 600 V rate Ga2O3SBD, and Al2O3is suitable for both600 V and 1200 V rate Ga2O3SBD. In addition, the comparison of Ga2O3SBDs between the SiC and GaN counterpart reveals that for Ga2O3, the breakdown voltage bottleneck is the dielectric. While, for SiC and GaN, the bottleneck is mainly the semiconductor itself.展开更多
Ga_2O_3 metal–oxide–semiconductor field-effect transistors(MOSFETs) with high-breakdown characteristics were fabricated on a homoepitaxial n-typed β-Ga_2O_3 film, which was grown by metal organic chemical vapor dep...Ga_2O_3 metal–oxide–semiconductor field-effect transistors(MOSFETs) with high-breakdown characteristics were fabricated on a homoepitaxial n-typed β-Ga_2O_3 film, which was grown by metal organic chemical vapor deposition(MOCVD) on an Fedoped semi-insulating(010) Ga_2O_3 substrate. The structure consisted of a 400 nm unintentionally doped(UID) Ga_2O_3 buffer layer and an 80 nm Si-doped channel layer. A high k HfO_2 gate dielectric film formed by atomic layer deposition was employed to reduce the gate leakage. Moreover, a source-connected field plate was introduced to enhance the breakdown characteristics. The drain saturation current density of the fabricated device reached 101 mA/mm at V_(gs) of 3 V. The off-state current was as low as 7.1 ×10^(-11) A/mm, and the drain current I_(ON)/I_(OFF) ratio reached 10~9. The transistors exhibited three-terminal off-state breakdown voltages of 450 and 550 V, corresponding to gate-to-drain spacing of 4 and 8 μm, respectively.展开更多
BACKGROUND The epiphyseal growth plate is an important anatomical segment localized on the ends of a long bone.Despite the abovementioned atractive reasons for alendronate’s use,few data on the effect of alendronate ...BACKGROUND The epiphyseal growth plate is an important anatomical segment localized on the ends of a long bone.Despite the abovementioned atractive reasons for alendronate’s use,few data on the effect of alendronate during epiphyseal growth exist.AIM Verify the effect of alendronate on the growth epiphyseal plate,and compare its effect with the size of the femur during the double-staining of the immunolocalization of transforming growth factor-β1(TGF-β1)and bone morphogenetic protein-2(BMP2)in endochondral ossifing in specimens that have received alendronate.METHODS Forty newborn rats were randomly divided into two groups:a control group(were given applications of 1 mg/kg physiologic saline)and a group that received Alendronate(a dose of 2.5 mg/kg).These groups were then divided into two subgroups for euthanasia in two and 12 d of life.After euthanasia,the femurs were removed,and the femoral bones were measured linearly between the apex of the greater trochanter until the lower intercondylar midlle face to verify the probable bone growth between 3 and 12 d in control and alednroanto treated rats.Posteriorly,the surgical pieces were also sent to the histopathology laboratory to produce histological slides.The obtained slides were stained with hematoxylin and eosin to measure each of the cartilage zones in endochondral development.and other slides were immunohistochemically tested for anti-TGF-β1 and BMP-2 antibodies to investigate the immunolocalization of these proteins in the epiphyseal plaque area.RESULTS On the third day,some diferences between the control group and specimens treated with alendronate were verified.Macroscopiccaly,we found similarities in size between the femoral bones when we compared the control group with the specimens that received alendronate.On the 12^th day,the bone size of the mice receiving the drug was significantly smaller than those of the control group.These results coincide with changes in the TGF-β1 and BMP-2 expression.In the specimens that received alendronate,the TGF-β1 was expressed in some sites of trabecular bone that was neoformed,peripherally to the bone marrow area.The BMP-2 was also positive in proliferative chondrocytes and hypertrofic chondrocytes.On the 12^th day,all layers of chondrocytes exhibited positivity for BMP-2 in the specimens that received alendronate.In the interface between the trabecular bone and cartilage,an area of disorganized bone deposition was evident.Neoformed bone also appeared to be different at 12 d.In the control group,BMP-2 was positive in an intense area of bone trabeculae,whereas the alendronate-treated group showed TGF-β1 positive trabeculae and a greater bone area.CONCLUSION Alendronate alters the immunolocalization of TGF-β1 and BMP-2 simultaneously,a condition that changes the usual histological aspects of the cartilage zone and impairs epiphysis growth and femur growth.展开更多
Today, latent heat storage technology has advanced to allow reuse of waste heat in the middle-temperature range. This paper describes an approach to develop a latent heat storage system using middle-temperature waste ...Today, latent heat storage technology has advanced to allow reuse of waste heat in the middle-temperature range. This paper describes an approach to develop a latent heat storage system using middle-temperature waste heat (~100oC - 200oC) from factories. Direct contact melting and solidification behavior between a heat-transfer fluid (oil) and a latent heat storage material mixture were observed. The mixture consisted of mannitol and erythritol (Cm = 70 mass %, Ce = 30 mass %) as a phase-change material (PCM). The weight of the PCM was 3.0 kg and the flow rate of the oil, foil, was 1.0, 1.5, or 2.0 kg/min. To decrease the solidified height of the PCM mixture during the solidification process, a perforated partition plate was installed in the PCM region in the heat storage vessel. PCM coated oil droplets were broken by the perforated partition plate, preventing the solidified height of the PCM from increasing. The solidification and melting processes were repeated using metal fiber. It was found that installing the metal fiber was more effective than installing the perforated partition plate to prevent the flow out problem of the PCM.展开更多
The Ar-N2 gas tungsten arc(GTA) welding of 10 mm copper thick plates without preheating was investigated.The microstructure of weld metal and joints was observed and mechanical performance of weld metal was tested by ...The Ar-N2 gas tungsten arc(GTA) welding of 10 mm copper thick plates without preheating was investigated.The microstructure of weld metal and joints was observed and mechanical performance of weld metal was tested by using Cu-Ti welding metal with different Ti content.The Ar-N2 GTA weld of copper thick plates can eliminate the nitrogen porosities in the weld metal by adding element Ti in filler metal,which is caused by N2 gas in shield gas.The elimination degree of nitrogen porosities,the distribution of CuTiN intermetallic compound(IMC) and the mechanical performance of joints are associated with the change of the Ti content in the welding materials.And when Ti content is about 5%,nitrogen porosities is eliminated completely and the CuTiN IMC distribute dispersedly,the tensile strength and impact ductility of the joint achieve the best result,which almost reaches the lever of the base metal.展开更多
Nanofluids are a potential alternative to significantly improving the performance of heat transfer applications. In this work, a numerical analysis to examine the eff ect of dispersing copper(Cu), copper oxide(CuO), a...Nanofluids are a potential alternative to significantly improving the performance of heat transfer applications. In this work, a numerical analysis to examine the eff ect of dispersing copper(Cu), copper oxide(CuO), and aluminum(Al2O3) nanoparticles in pure water on the performance of a flat plate solar collector(FPSC) and a numerical model was proposed. The influence of the nanofluid type on the thermal efficiency was critically investigated and discussed. The eff ect of the mass flow rate on the performance was also analyzed and discussed. Based on correlations of the thermophysical properties of nanofluids, a sensitivity analysis was used to analyze the impact of the nanoparticles on the base fluid. The results indicate that the performance of the FPSC with Cu/water nanofluid was better than that of FPSCs using CuO/water or Al2O3/water nanofluids. When the mass flow rate of the nanofluids was 8.0 L/min, the efficiency of the FPSC was much greater than those at the flow rates of 5.0 L/min and 2.0 L/min. Mean enhancements in thermal efficiency of 4.44%, 4.27%, and 4.21% were observed when 2.0 L/min was applied using Cu/water, Cu O/water, and Al2O3/water nanofluids, respectively. Improvements in thermal efficiency of 2.76%, 2.53%, and 2.47% occurred when 8.0 L/min was applied.展开更多
基金Project supported by the Research Fund of Low Cost Fabrication of GaN Power Devices and System Integration,China(Grant No.JCYJ20160226192639004)the Research Fund of AlGaN HEMT MEMS Sensor for Work in Extreme Environment,China(Grant No.JCYJ20170412153356899)the Research Fund of Reliability Mechanism and Circuit Simulation of GaN HEMT,China(Grant No.2017A050506002)
文摘In this work, the field plate termination is studied for Ga2O3Schottky barrier diodes(SBDs) by simulation. The influence of field plate overlap, dielectric material and thickness on the termination electric field distribution are demonstrated.It is found that the optimal thickness increases with reverse bias increasing for all the three dielectrics of SiO2, Al2O3, and HfO2. As the thickness increases, the maximum electric field intensity decreases in SiO2and Al2O3, but increases in HfO2.Furthermore, it is found that SiO2and HfO2are suitable for the 600 V rate Ga2O3SBD, and Al2O3is suitable for both600 V and 1200 V rate Ga2O3SBD. In addition, the comparison of Ga2O3SBDs between the SiC and GaN counterpart reveals that for Ga2O3, the breakdown voltage bottleneck is the dielectric. While, for SiC and GaN, the bottleneck is mainly the semiconductor itself.
基金supported by the National Natural Science Foundation of China(Nos.61674130,61604137)
文摘Ga_2O_3 metal–oxide–semiconductor field-effect transistors(MOSFETs) with high-breakdown characteristics were fabricated on a homoepitaxial n-typed β-Ga_2O_3 film, which was grown by metal organic chemical vapor deposition(MOCVD) on an Fedoped semi-insulating(010) Ga_2O_3 substrate. The structure consisted of a 400 nm unintentionally doped(UID) Ga_2O_3 buffer layer and an 80 nm Si-doped channel layer. A high k HfO_2 gate dielectric film formed by atomic layer deposition was employed to reduce the gate leakage. Moreover, a source-connected field plate was introduced to enhance the breakdown characteristics. The drain saturation current density of the fabricated device reached 101 mA/mm at V_(gs) of 3 V. The off-state current was as low as 7.1 ×10^(-11) A/mm, and the drain current I_(ON)/I_(OFF) ratio reached 10~9. The transistors exhibited three-terminal off-state breakdown voltages of 450 and 550 V, corresponding to gate-to-drain spacing of 4 and 8 μm, respectively.
文摘BACKGROUND The epiphyseal growth plate is an important anatomical segment localized on the ends of a long bone.Despite the abovementioned atractive reasons for alendronate’s use,few data on the effect of alendronate during epiphyseal growth exist.AIM Verify the effect of alendronate on the growth epiphyseal plate,and compare its effect with the size of the femur during the double-staining of the immunolocalization of transforming growth factor-β1(TGF-β1)and bone morphogenetic protein-2(BMP2)in endochondral ossifing in specimens that have received alendronate.METHODS Forty newborn rats were randomly divided into two groups:a control group(were given applications of 1 mg/kg physiologic saline)and a group that received Alendronate(a dose of 2.5 mg/kg).These groups were then divided into two subgroups for euthanasia in two and 12 d of life.After euthanasia,the femurs were removed,and the femoral bones were measured linearly between the apex of the greater trochanter until the lower intercondylar midlle face to verify the probable bone growth between 3 and 12 d in control and alednroanto treated rats.Posteriorly,the surgical pieces were also sent to the histopathology laboratory to produce histological slides.The obtained slides were stained with hematoxylin and eosin to measure each of the cartilage zones in endochondral development.and other slides were immunohistochemically tested for anti-TGF-β1 and BMP-2 antibodies to investigate the immunolocalization of these proteins in the epiphyseal plaque area.RESULTS On the third day,some diferences between the control group and specimens treated with alendronate were verified.Macroscopiccaly,we found similarities in size between the femoral bones when we compared the control group with the specimens that received alendronate.On the 12^th day,the bone size of the mice receiving the drug was significantly smaller than those of the control group.These results coincide with changes in the TGF-β1 and BMP-2 expression.In the specimens that received alendronate,the TGF-β1 was expressed in some sites of trabecular bone that was neoformed,peripherally to the bone marrow area.The BMP-2 was also positive in proliferative chondrocytes and hypertrofic chondrocytes.On the 12^th day,all layers of chondrocytes exhibited positivity for BMP-2 in the specimens that received alendronate.In the interface between the trabecular bone and cartilage,an area of disorganized bone deposition was evident.Neoformed bone also appeared to be different at 12 d.In the control group,BMP-2 was positive in an intense area of bone trabeculae,whereas the alendronate-treated group showed TGF-β1 positive trabeculae and a greater bone area.CONCLUSION Alendronate alters the immunolocalization of TGF-β1 and BMP-2 simultaneously,a condition that changes the usual histological aspects of the cartilage zone and impairs epiphysis growth and femur growth.
文摘Today, latent heat storage technology has advanced to allow reuse of waste heat in the middle-temperature range. This paper describes an approach to develop a latent heat storage system using middle-temperature waste heat (~100oC - 200oC) from factories. Direct contact melting and solidification behavior between a heat-transfer fluid (oil) and a latent heat storage material mixture were observed. The mixture consisted of mannitol and erythritol (Cm = 70 mass %, Ce = 30 mass %) as a phase-change material (PCM). The weight of the PCM was 3.0 kg and the flow rate of the oil, foil, was 1.0, 1.5, or 2.0 kg/min. To decrease the solidified height of the PCM mixture during the solidification process, a perforated partition plate was installed in the PCM region in the heat storage vessel. PCM coated oil droplets were broken by the perforated partition plate, preventing the solidified height of the PCM from increasing. The solidification and melting processes were repeated using metal fiber. It was found that installing the metal fiber was more effective than installing the perforated partition plate to prevent the flow out problem of the PCM.
基金Funded by Program of Excellent Team in Harbin Institute of Technology
文摘The Ar-N2 gas tungsten arc(GTA) welding of 10 mm copper thick plates without preheating was investigated.The microstructure of weld metal and joints was observed and mechanical performance of weld metal was tested by using Cu-Ti welding metal with different Ti content.The Ar-N2 GTA weld of copper thick plates can eliminate the nitrogen porosities in the weld metal by adding element Ti in filler metal,which is caused by N2 gas in shield gas.The elimination degree of nitrogen porosities,the distribution of CuTiN intermetallic compound(IMC) and the mechanical performance of joints are associated with the change of the Ti content in the welding materials.And when Ti content is about 5%,nitrogen porosities is eliminated completely and the CuTiN IMC distribute dispersedly,the tensile strength and impact ductility of the joint achieve the best result,which almost reaches the lever of the base metal.
文摘Nanofluids are a potential alternative to significantly improving the performance of heat transfer applications. In this work, a numerical analysis to examine the eff ect of dispersing copper(Cu), copper oxide(CuO), and aluminum(Al2O3) nanoparticles in pure water on the performance of a flat plate solar collector(FPSC) and a numerical model was proposed. The influence of the nanofluid type on the thermal efficiency was critically investigated and discussed. The eff ect of the mass flow rate on the performance was also analyzed and discussed. Based on correlations of the thermophysical properties of nanofluids, a sensitivity analysis was used to analyze the impact of the nanoparticles on the base fluid. The results indicate that the performance of the FPSC with Cu/water nanofluid was better than that of FPSCs using CuO/water or Al2O3/water nanofluids. When the mass flow rate of the nanofluids was 8.0 L/min, the efficiency of the FPSC was much greater than those at the flow rates of 5.0 L/min and 2.0 L/min. Mean enhancements in thermal efficiency of 4.44%, 4.27%, and 4.21% were observed when 2.0 L/min was applied using Cu/water, Cu O/water, and Al2O3/water nanofluids, respectively. Improvements in thermal efficiency of 2.76%, 2.53%, and 2.47% occurred when 8.0 L/min was applied.
