The use of ultra-high strength steels through sheet metal forming process offers a practical solution to the lightweight design of vehicles.However,sheet metal forming process not only produces desirable changes in ma...The use of ultra-high strength steels through sheet metal forming process offers a practical solution to the lightweight design of vehicles.However,sheet metal forming process not only produces desirable changes in material properties but also causes material damage that may adversely influence the service performance of the material formed.Thus,an investigation is conducted to experimentally quantify such influence for a commonly used steel(the 22MnB5 steel) based on the hot and cold forming processes.For each process,a number of samples are used to conduct a uniaxial tensile test to simulate the forming process.After that,some of the samples are trimmed into a standard shape and then uniaxially extended until fracture to simulate the service stage.Finally,a microstructure test is conducted to analyze the microdefects of the remaining samples.Based on the results of the first two tests,the effect of material damage on the service performance of 22MnB5 steel is analyzed.It is found that the material damages of both the hot and cold forming processes cause reductions in the service performance,such as the failure strain,the ultimate stress,the capacity of energy absorption and the ratio of residual strain.The reductions are generally lower and non-linear in the former process but higher and linear in the latter process.Additionally,it is found from the microstructure analysis that the difference in the reductions of the service performance of 22MnB5 by the two forming processes is driven by the difference in the micro damage mechanisms of the two processes.The findings of this research provide a useful reference in terms of the selection of sheet metal forming processes and the determination of forming parameters for 22MnB5.展开更多
Hot stamping components with 1500 MPa ultra-high strength are obtained by press hardening during hot stamping, and the properties depend on the microstructures. It is very important that the microstructure evolution r...Hot stamping components with 1500 MPa ultra-high strength are obtained by press hardening during hot stamping, and the properties depend on the microstructures. It is very important that the microstructure evolution rule is found out during hot stamping process. To characterize the microstructure evolution during hot stamping, a method combining finite element and experiment is carried out. Samples were heated to 950°C and held for 300 second at a induction heating furnace, then taken out from the furnace and stayed in the air at different time (7 s, 11 s, 13 s, 22 s), respectively, finally the specimens were formed and quenched at a die. Microstructural observation as well as surface hardness profiling of formed specimens was performed. And the numerical simulation to predict the austenite transformation into ferrite, pearlite, bainite, and martensite and the volume fraction of each phase during the hot stamping process was made with ABAQUS software. The results show that the ferrite is observed when the specimen stays in the air for 22 s, and the temperature drops to 325°C when the dwell time increases from 7 s to 22 s. The results of numerical simulation and experimental results are in good agreement. So the method finite element can be used to guide the optimization of hot stamping process parameters.展开更多
基金Supported by National Natural Science Foundation of China(Grant No.51375201)CSAE(Beijing)Automotive Lightweight Technology Research Institute Development Fund Project of China
文摘The use of ultra-high strength steels through sheet metal forming process offers a practical solution to the lightweight design of vehicles.However,sheet metal forming process not only produces desirable changes in material properties but also causes material damage that may adversely influence the service performance of the material formed.Thus,an investigation is conducted to experimentally quantify such influence for a commonly used steel(the 22MnB5 steel) based on the hot and cold forming processes.For each process,a number of samples are used to conduct a uniaxial tensile test to simulate the forming process.After that,some of the samples are trimmed into a standard shape and then uniaxially extended until fracture to simulate the service stage.Finally,a microstructure test is conducted to analyze the microdefects of the remaining samples.Based on the results of the first two tests,the effect of material damage on the service performance of 22MnB5 steel is analyzed.It is found that the material damages of both the hot and cold forming processes cause reductions in the service performance,such as the failure strain,the ultimate stress,the capacity of energy absorption and the ratio of residual strain.The reductions are generally lower and non-linear in the former process but higher and linear in the latter process.Additionally,it is found from the microstructure analysis that the difference in the reductions of the service performance of 22MnB5 by the two forming processes is driven by the difference in the micro damage mechanisms of the two processes.The findings of this research provide a useful reference in terms of the selection of sheet metal forming processes and the determination of forming parameters for 22MnB5.
文摘Hot stamping components with 1500 MPa ultra-high strength are obtained by press hardening during hot stamping, and the properties depend on the microstructures. It is very important that the microstructure evolution rule is found out during hot stamping process. To characterize the microstructure evolution during hot stamping, a method combining finite element and experiment is carried out. Samples were heated to 950°C and held for 300 second at a induction heating furnace, then taken out from the furnace and stayed in the air at different time (7 s, 11 s, 13 s, 22 s), respectively, finally the specimens were formed and quenched at a die. Microstructural observation as well as surface hardness profiling of formed specimens was performed. And the numerical simulation to predict the austenite transformation into ferrite, pearlite, bainite, and martensite and the volume fraction of each phase during the hot stamping process was made with ABAQUS software. The results show that the ferrite is observed when the specimen stays in the air for 22 s, and the temperature drops to 325°C when the dwell time increases from 7 s to 22 s. The results of numerical simulation and experimental results are in good agreement. So the method finite element can be used to guide the optimization of hot stamping process parameters.