“三化”法在初中思想品德复习课中的应用

初中思想品德课程所涉及的知识点比较多,理论性也比较强。如何在有限的复习课的时间内,让学生记住和理解繁多的知识点,提高复习课的效率,是广大初中思想品德课教师面临的重要任务。

一题看透第二型曲线积分的计算方法

第二型曲线积分的计算联系着各类积分,根据积分路径和被积函数的特点,可将其转化为定积分、重积分或曲面积分来计算。这种训练既能简化其计算,又有利于积分知识的融会贯通与灵活运用。本文着重介绍了第二型曲线积分的六种基本算法:投影法、"二化一"法、斯托克斯公式法、格林公式法、"三化二"法。

Trigonometric Regularization and Continuation Method Based Time-Optimal Control of Hypersonic Vehicles

Aiming at the time-optimal control problem of hypersonic vehicles(HSV)in ascending stage,a trigonometric regularization method(TRM)is introduced based on the indirect method of optimal control.This method avoids analyzing the switching function and distinguishing between singular control and bang-bang control,where the singular control problem is more complicated.While in bang-bang control,the costate variables are unsmooth due to the control jumping,resulting in difficulty in solving the two-point boundary value problem(TPBVP)induced by the indirect method.Aiming at the easy divergence when solving the TPBVP,the continuation method is introduced.This method uses the solution of the simplified problem as the initial value of the iteration.Then through solving a series of TPBVP,it approximates to the solution of the original complex problem.The calculation results show that through the above two methods,the time-optimal control problem of HSV in ascending stage under the complex model can be solved conveniently.

浅谈高职学生兴趣培养与能力提高——以《工程力学》为例

本文以高职院校工程力学课程为研究对象,结合专业特点,提出了基于“三化”法的概念讲解;公式的推导过程化与强化记忆比较法等教学方法.并与传统的教学进行了比较,以期提高课程教学.

Low-temperature catalytic oxidation of formaldehyde over Co_3O_4catalysts prepared using various precipitants

Co3O4 catalysts prepared with different precipitants（NH3·H2O,KOH,NH4HCO3,K2CO3 and KHCO3）were investigated for the oxidation of formaldehyde（HCHO）.Among these,KHCO3-precipitated Co3O4（KHCO3-Co） was the most active low-temperature catalyst,and was able to completely oxidize HCHO at the 100-ppm level to CO2 at 90℃.In situ diffuse reflectance infrared spectroscopy demonstrated that hydroxyl groups on the catalyst surface were regenerated by K~＋ and CO3^（2-）,thus promoting the oxidation of HCHO.Moreover,H2-temperature programmed reduction and X-ray photoelectron spectroscopy showed that employing KHCO3 as the precipitant increased the Co^3＋/Co^2＋molar ratio on the surface of the Co3O4 catalyst,thus further promoting oxidation.Structural characterization revealed that catalysts precipitated with carbonate or bicarbonate reagents exhibited greater specific surface areas and pore volumes.Overall,these data suggest that the high activity observed during the Co3O4 catalyzed oxidation of HCHO can be primarily attributed to the presence of K~＋ and CO3^（2-） on the Co3O4 surface and the favorable Co^3＋/Co^2＋ ratio.

从翻译美学角度浅析《诗经·蒹葭》的英译策略

《诗经·蒹葭》是我国古代一首"情深景真、风神摇曳"的怀人诗,优美的意境和凄婉缠绵的情致使其在中国文学史上独领风骚。本文以翻译美学理论为指导,结合"三美"原则,即意美、音美和形美对许渊冲英译的《诗经·蒹葭》进行鉴赏和评析。探究此诗中蕴含的美学特征,进而揭示在"三美"的基本原则上,采用"三化"法的翻译策略。

Visualization of 3-D Field of Explosion

In order to visualize the 3-D field of explosion and describe the complex physical phenomena of explosion, the 3-D data resulting from numerical simulation by 3-D multi-material in cell (MMIC), and the application of volume visualization is explored, based on the characteristics of explosion and shock. Based on this, a visualization system for 3-D explosion--ViSC3D is designed. Approaches for the visualization of 3-D field of explosion are presented. The algorithm and the functions of ViSC3D are also presented. ViSC3D is thus a useful tool to observe and analyze either the full picture or the details of a 3-D field of explosion, that are difficult to observe and analyze directly. With ViSC3D, the field of explosion between the hill slopes is visualized. The cutaway views and 2-D slices are also given. The full picture and partial details of 3-D field of explosion can be observed clearly. Furthermore, ViSC3D can be used to visualize other similar 3-D data fields.

Extrapolated Tikhonov method and inversion of 3D density images of gravity data

Tikhonov regularization（TR） method has played a very important role in the gravity data and magnetic data process. In this paper, the Tikhonov regularization method with respect to the inversion of gravity data is discussed. and the extrapolated TR method（EXTR） is introduced to improve the fitting error. Furthermore, the effect of the parameters in the EXTR method on the fitting error, number of iterations, and inversion results are discussed in details. The computation results using a synthetic model with the same and different densities indicated that. compared with the TR method, the EXTR method not only achieves the a priori fitting error level set by the interpreter but also increases the fitting precision, although it increases the computation time and number of iterations. And the EXTR inversion results are more compact than the TR inversion results, which are more divergent. The range of the inversion data is closer to the default range of the model parameters, and the model features and default model density distribution agree well.

Studies on the Mechanism of Arsenic Trioxide-Induced Apoptosis in HepG_2 Human Hepatocellular Carcinoma Cells

OBJECTIVE To study the anti-tumor effect of arsenic trioxide on the HepG2 human hepatocellular carcinoma cell line, and to explore its mechanism of action. METHODS The MTT assay was used to determine the inhibitory effect of As2O3 on HepG2 cells at various As2O3 concentrations. The expression of p-JNK, caspase-3 and PARP was detected by Western blots. RESULTS As2O3 markedly inhibited the growth of the HepG2 cells and induced apoptosis. The results of Western blot analysis showed that the As2O3-induced apoptosis was accompanied by caspase-3 and PARP activation. p-JNK was detected at 10 min following As2O3 treatment, and preceded to peak at 20 min, and decreased by 30 min. The total protein content did not obviously change. The activation of JNK occurred prior to cell apoptosis. SP600125, a JNK inhibitor, suppressed the As2O3-induced activation of caspase-3 and PARP cleavage. CONCLUSION As2O3 inhibits the proliferation of human HepG2 hepatocellular carcinoma cells by inducing apoptosis in vitro. As2O3-induced apoptosis is accessed through the caspase-3 pathway. The JNK signal-transduction pathway and caspase-3 are involved upstream in the As2O3 induced HepG2 apoptotic response.

Characterization of V_2O_5/MoO_3 composite photocatalysts prepared via electrospinning and their photodegradation activity for dimethyl phthalate

Vanadium pentoxide（V2O5）/molybdenum trioxide（MoO 3） composites with different molar ratios of vanadium（V） to molybdenum（Mo） were synthesized via a simple electrospinning technique. The photocatalytic activity of the composites were evaluated by their ability to photodegrade methylene blue and dimethyl phthalate（DMP） under visible-light irradiation. Compared with pure V2O5 and MoO 3,the V2O5/MoO 3 composites showed enhanced visible-light photocatalytic activity because of a V 3d impurity energy level and the formation of heterostructures at the interface between V2O5 and MoO 3. The optimal molar ratio of V to Mo in the V2O5/MoO 3 composites was found to be around 1/2. Furthermore,high-performance liquid chromatographic monitoring revealed that phthalic acid was the main intermediate in the photocatalytic degradation process of DMP.

Optimization algorithm for rapid 3D gravity inversion

The practical application of 3D inversion of gravity data requires a lot of computation time and storage space.To solve this problem,we present an integrated optimization algorithm with the following components:(1)targeting high accuracy in the space domain and fast computation in the wavenumber domain,we design a fast 3D forward algorithm with high precision;and(2)taking advantage of the symmetry of the inversion matrix,the main calculation in gravity conjugate gradient inversion is decomposed into two forward calculations,thus optimizing the computational efficiency of 3D gravity inversion.We verify the calculation accuracy and efficiency of the optimization algorithm by testing various grid-number models through numerical simulation experiments.

Recovery of copper sulfate after treating As-containing wastewater by precipitation method

The solid sodium hydroxide neutralized acidic As-containing wastewater till pH value was 6. Green copper arsenite was prepared after copper sulfate was added into the neutralized wastewater when the molar ratio of Cu to As was 2：1 and pH value of the neutralized wastewater was adjusted to 8.0 by sodium hydroxide. The arsenious acid solution and red residue were produced after copper arsenite mixed with water according to the ratio of liquid to solid of 4：1 and copper arsenite was reduced by SO2 at 60℃ for 1 h. The white powder was gained after the arsenious acid solution was evaporated and cooled. Copper sulfate solution was obtained after the red residue was leached by H2SO4 solution under the action of air. The results show that red residue is Cu3（SO3）2·2H2O and the white powder is As2O3. The leaching rate of Cu reaches 99.00% when the leaching time is 1.5 h, molar ratio of H2SO4 to Cu is 1.70, H2SO4 concentration is 24% and the leaching temperature is 80 ℃. The direct recovery rate of copper sulfate is 79.11% and the content of CuSOa·5H2O is up to 98.33% in the product after evaporating and cooling the copper sulfate solution.

Determination of work-hardening exponent for sheet metal using three-point method

Three characteristic points in the deformation history of a fractured tensile specimen are selected tocalculate two values of n( n1 and n2 ) to represent the hardening ability of material during the homogeneous plas-tic deformation and the following large plastic deformation. Experimental results obtained with mild streel andred copper show that n determined using the three-point method proposed is better to describe the hardening a-bility of material. It is therefore concluded that three-point method can be used to describe the hardening prop-erty of material during both homogeneous deformation and large plastic deformation.

First-principles calculations of structural, electronic, elastic and thermal properties of phase M_2SiC(M=Ti,V,Cr,Zr,Nb,Mo,Hf,Ta and W)

The structural,electronic and elastic properties of the M_2SiC phases were studied,where M are 3d,4d,and 5d early transition metals.The valence electron concentration(VEC) effect of Ti,V,Cr,Zr,Nb,Mo,Hf,Ta and W on these properties was examined.The C_(44) saturates for a VEC value in surrounding of 8.5 for each serie.Hf-s,Ta-s and W-s electrons mainly contribute to the density of states at the Fermi level,and should be involved in the conduction properties.The distortion increases with increasing VEC and decreasing k_c/k_a factor except for the series M=Ti,V and Cr,where it is lower at the VEC value of 8.5(it follows a parabolic variation).The M_2SiC was characterized by a profound anisotropy for the shear planes(1010) and compressibility in the direction is higher than that along the cone except for W_2SiC,where it is lower.

Effect of Ferric Chloride on the Properties of Biological Sludge in Co-precipitation Phosphorus Removal Process

This paper studied the effect of ferric chloride on waste sludge digestion,dewatering and sedimentation under the optimized doses in co-precipitation phosphorus removal process.The experimental results showed that the concentration of mixed liquid suspended solid(MLSS) was 2436 mg.L-1 and 2385 mg.L-1 in co-precipitation phosphorus removal process(CPR) and biological phosphorous removal process(BPR),respectively.The sludge reduction ratio for each process was 22.6% and 24.6% in aerobic digestion,and 27.6% and 29.9% in anaerobic digestion,respectively.Due to the addition of chemical to the end of aeration tank,the sludge content of CPR was slightly higher than that of BPR,but the sludge reduction rate for both processes had no distinct difference.The sludge volume index(SVI) and sludge specific resistance of BPR were 126 ml.g-1 and 11.7×1012 m.kg-1,respectively,while those of CPR were only 98 ml.g-1 and 7.1×1012 m.kg-1,indicating that CPR chemical could improve sludge settling and dewatering.

Inversion of 3D density interface with PSO-BP method

BP( Back Propagation) neural network and PSO( Particle Swarm Optimization) are two main heuristic optimization methods,and are usually used as nonlinear inversion methods in geophysics. The authors applied BP neural network and BP neural network optimized with PSO into the inversion of 3D density interface respectively,and a comparison was drawn to demonstrate the inversion results. To start with,a synthetic density interface model was created and we used the proceeding inversion methods to test their effectiveness. And then two methods were applied into the inversion of the depth of Moho interface. According to the results,it is clear to find that the application effect of PSO-BP is better than that of BP network. The BP network structures used in both synthetic and field data are consistent in order to obtain preferable inversion results. The applications in synthetic and field tests demonstrate that PSO-BP is a fast and effective method in the inversion of 3D density interface and the optimization effect is evident compared with BP neural network merely,and thus,this method has practical value.

Electrogenerative leaching of nickel sulfide concentrate with ferric chloride

In order to utilize the chemical energy in hydrometallurgical process of sulfide minerals reasonably and to simplify the purifying process, the electrogenerative process was applied and a dual cell system was introduced to investigate FeCl3 leaching of nickel sulfide concentrate. Some factors influencing the electrogenerative leaching, such as electrode structure, temperature and solution concentration were studied. The results show that a certain quantity of electrical energy accompanied with the leached products can be acquired in the electrogenerative leaching process. The output current and power increase with the addition of acetylene black to the electrode. Varying the components of electrode just affects the polarization degree of anode. Increasing FeCl3 concentration results in a sharp increase in the output of the leaching cell when c（FeCl3） is less than 0.1 mol/L. The optimum value of NaCl concentration for electrogenerative leaching nickel sulfide concentrate with FeCl3 is 3.0 mol/L. Temperature influences electrogenerative leaching by affecting anodic and cathodic polarization simultaneously. The apparent activation energy is determined to be 34.63 kJ/mol in the range of 298 K to 322 K. The leaching rate of Ni2+ is 29.3% after FeCl3 electrogenerative leaching of nickel sulfide concentrate for 620 min with a filter bag electrode.

Optimization of three-dimensional boiling enhancement structure at evaporation surface for high power light emitting diode

A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were determined. Subsequently, the forming methods including ploughing-extrusion and stamping method of boiling enhancement structure at evaporation surface were investigated, upon which three-dimensional microgroove structure was fabricated to improve the efficiency of evaporation. Moreover, the crucial parameters related to the fabrication of miniaturized phase change heat sink were optimized. The heat transfer performance of the heat sink was tested. Results show that the developed phase change heat sink has excellent heat transfer performance and is suitable for high power LED applications.

Generalized fairing algorithm of parametric cubic splines

Kjellander has reported an algorithm for fairing uniform parametric cubic splines. Poliakoff extended Kjellander’s algorithm to non-uniform case. However, they merely changed the bad point’s position, and neglected the smoothing of tangent at bad point. In this paper, we present a fairing algorithm that both changed point’s position and its corresponding tangent vector. The new algorithm possesses the minimum property of energy. We also proved Poliakoff’s fairing algorithm is a deduction of our fairing algorithm. Several fairing examples are given in this paper.

Optimized Triangulation Algorithm in Terrain Modeling

3D reconstruction of terrain model based on digital line graphics (DLG) is discussed. An auto-coupling triangles algo-rithm based on triangle topological relationship is put forward, and the topological data model of complicated terrain is developed. Based on this data model, automatic 3D topological reconstruction of terrain is realized.