A New Method to Retrieve Proximity Effect Parameters in Electron-Beam Lithography

A new method for determining proximity parameters α,β ,and η in electron beam lithography is introduced on the assumption that the point exposure spread function is composed of two Gaussians.A single line is used as test pattern to determine proximity effect parameters and the normalization approach is adopted in experimental data transaction in order to eliminate the need of measuring exposure clearing dose of the resist.Furthermore,the parameters acquired by this method are successfully used for proximity effect correction in electron beam lithography on the same experimental conditions.

Delayed-Dipole Domain Mode of Semi-Insulating GaAs Photoconductive Semiconductor Switches

A mode for the periodicity and weakening surge in semi-insulating GaAs photoconductive semiconductor switches is proposed based on the transferred-electron effect. It is shown that the periodicity and weakening surge is caused by the interaction between the self-excitation of the resonant circuit and transferred electron oscillation of the switch. The bias electric field （larger than Gunn threshold） across the switch is modulated by the AC elec-tric field,when the instantaneous bias electric field E is swinging below Gunn electric field threshold ET but grea-ter than the sustaining field Es （the minimum electric field required to support the domain） at the time of the do-main reaching the anode, and then the delayed-dipole domain mode of switch is obtained. It is the photon-activated carriers that satisfy the requirement of charge domain formation on carrier concentration and device length prod-uct of 10^12 cm^-2,and the semi-insulating GaAs photoconductive semiconductor switch is essentially a type of pho-ton-activated charge domain device.

A High-Performance Silicon Electro-Optic Phase Modulator with a Triple MOS Capacitor

We propose and analyze a novel Si-based electro-optic modulator with an improved metal-oxide-semiconductor （MOS） capacitor configuration integrated into silicon-on-insulator （SOl）. Three gate-oxide layers embedded in the silicon waveguide constitute a triple MOS capacitor structure, which boosts the modulation efficiency compared with a single MOS capacitor. The simulation results demonstrate that the Vπ Lπ product is 2. 4V · cm. The rise time and fall time of the proposed device are calculated to be 80 and 40ps from the transient response curve, respectively,indicating a bandwidth of 8GHz. The phase shift efficiency and bandwidth can be enhanced by rib width scaling.

Transient Characteristics of a Nonlinear GaAs Photoconductive Semiconductor Switch

The transient resistance,voltage,and power of a nonlinear GaAs photoconductive semiconductor switch （PCSS） are presented by the finite difference formula to deal with the experiment data, based on the conversation of energy in the switch circuit. This method resolves the problem of directly measuring the transient characteristics of PCSS in nonlinear mode. The curve of transient voltage shows that the average electric field of PCSS in the lock-on period is always higher than the Gunn threshold,and increases monotonically. By comparing the transient power curves of the PCSS and the electrical source,it is demonstrated directly that the power shortage leads to the PCSS from the lock-on state into the selfturnoff state,so a controllable turnoff of the PCSS in lock-on by changing the distribution of the circuit power is predicted.

Fabrication of Sub-20nm Metal Nanogaps from Nanoconnections by the Extended Proximity Effect

We describe the fabrication of metal nanogaps of sub-20nm in feature size using the proximity effect in electron beam lithography （EBL）. The proximity effect is extended to develop a flexible and practical method for preparing metal （e. g. Au or Ag） nanogaps and arrays in combination with a transfer process （e. g., deposition/lift-off）. Different from the direct gap-writing process,the nanogap precursor structures （nanoconnections） were designed by GDSII software and then written by electron beam. Following a deposition and lift-off process, the metal nanogaps were obtained and the nanogap size can be lowered to -10nm by controlling the exposure dose in EBL.

A tetragonal tungsten bronze-type photocatalyst:Ferro-paraelectric phase transition and photocatalysis

Although ferroelectrics have potential applications in photocatalysis due to their highly efficient charge separation, their mechanism of charge separation is still unknown. A ferroelectric Sr0.7Ba0.3Nb2O6 （SBN‐70） semiconductor with a low ferro‐paraelectric phase transition （65℃） was studied. The photocatalytic activity for H2 production by ferroelectric and paraelectric SBN‐70 was examined. The spontaneous polarization in the ferroelectric phase strongly affected the photocata‐lytic performance and parallel ferroelectric domains significantly promoted photogenerated charge separation to result in better photocatalytic H2 production. This knowledge provides an important basis for the fabrication of ferroelectric photocatalysts with improved charge separation ability.

Electro-Optical Effect Measurement of Thin-Film Material Using PM Fiber Mach-Zehnder Interferometer

A polarization-maintaining （PM） fiber Mach-Zehnder （MZ） interferometer has been established to measure the EO effect of very thin film materials with optical anisotropy. Unlike a common MZ interferometer, all the components are connected via polarization-maintaining fibers. At the same time, a polarized DFB laser with a maximum power output of 10mW is adopted as the light source to induce a large extinction ratio. Here,we take it to determine the electro-optical coefficients of a very thin superlattice structure with GaAs, KTP, and GaN as comparative samples. The measured EO coefficients show good comparability with the others.

Piezopotential augmented photo-and photoelectro-catalysis with a built-in electric field

Rapid technological development and population growth are responsible for a series of imminent environmental problems and an ineluctable energy crisis.The application of semiconductor nanomaterials in photocatalysis or photoelectrocatalysis(PEC)for either the degradation of contaminants in the environment or the generation of hydrogen as clean fuel is an effective approach to alleviate these problems.However,the efficiency of such processes remains suboptimal for real applications.Reasonable construction of a built-in electric field is considered to efficiently enhance carrier separation and reduce carrier recombination to improve catalytic performance.In the past decade,as a new method to enhance the built-in electric field,the piezoelectric effect from piezoelectric materials has been extensively studied.In this review,we provide an overview of the properties of piezoelectric materials and the mechanisms of piezoelectricity and ferroelectricity for a built-in electric field.Then,piezoelectric and ferroelectric polarization regulated built-in electric fields that mediate catalysis are discussed.Furthermore,the applications of piezoelectric semiconductor materials are also highlighted,including degradation of pollutants,bacteria disinfection,water splitting for H2 generation,and organic synthesis.We conclude by discussing the challenges in the field and the exciting opportunities to further improve piezo-catalytic efficiency.

Molecular Frame Photoemission： Probe of the Photoionization Dynamics for Molecules in the Gas Phase

Molecular frame photoemission is a very sensitive probe of the photoionization （PI） dynamics of molecules. This paper reports a comparative study of non-resonant and resonant photoionization of D2 induced by VUV circularly polarized synchrotron radiation at SOLEIL at the level of the molecular frame photoelectron angular distributions （MFPADs）. We use the vector correlation method which combines imaging and time-of-flight resolved electron-ion coincidence techniques, and a generalized formalism for the expression of the Ⅰ（χ, θe, Фe） MFPADs, where χ is the orientation of the molecular axis with respect to the light quantization axis and （θe, Фe） the electron emission direction in the molecular frame. Selected MFPADs for a molecule aligned parallel or perpendicular to linearly polarized light, or perpendicular to the propagation axis of circularly polarized light, are presented for dissociative photoionization （DPI） of D2 at two photon excitation energies, hv=19 eV, where direct PI is the only channel opened, and hv=32.5 eV, i.e. in the region involving resonant excitation of Q1 and Q2 doubly excited state series. We discuss in particular the properties of the circular dichroism characterizing photoemission in the molecular frame for direct and resonant PI. In the latter case, a remarkable behavior is observed which may be attributed to the interference occurring between undistinguishable autoionization decay channels.

Nonlinear effect induced in thermally poled glass waveguides

Thermally poled germanium-doped channel waveguides are presented. Multilayer waveguides containing a silicon oxynitride layer were used as charge trapper in this investigation on the effect of the internal field inside the waveguide. Compared to waveguides without the trapping layer, experimental results showed that the induced linear electro-optic (EO) coefficient increases about 20% after poling, suggesting strongly that the internal field is relatively enhanced, and showed it is a promising means for improving nonlinearity by poling in waveguides.

An All-E-Beam Lithography Process for the Patterning of 2D Photonic Crystal Waveguide Devices

We present an all-e-beam lithography （EBL） process for the patterning of photonic crystal waveguides. The whole device structures are exposed in two steps. Holes constituting the photonic crystal lattice and defects are first exposed with a small exposure step size （less than 10nm）. With the introduction of the additional proximity effect to compensate the original proximity effect, the shape, size, and position of the holes can be well controlled. The second step is the exposure of the access waveguides at a larger step size （about 30nm） to improve the scan speed of the EBL. The influence of write-field stitching error can be alleviated by replacing the original waveguides with tapered waveguides at the joint of adjacent write-fields. It is found experimentally that a higher exposure efficiency is achieved with a larger step size;however,a larger step size requires a higher dose.

Preparation and photoelectric effect of Zn^(2+)-TiO_2 nanotube arrays

Zn 2+-TiO2 nanotube arrays were prepared by anodic oxidation method.The current-time curves were used to investigate their growth mechanism.Scanning electron microscopy and X-ray diffractometry were applied to characterizing their structures and properties.The photoelectrochemical properties were studied by electrochemical impedance spectrum(EIS).The optimised working conditions for TiO2 nanotube arrays were found to be pH 1,0.5%HF(mass fraction),20 V oxidation voltage and for 2 h.The produced sample was in anatase form,with length of 70-100 nm,thickness of 10 nm,uniform diameter and structure that does not collapse under the preparation conditions.The EIS results show that TiO2 nanotube arrays prepared with 0.5%HF(mass fraction) present a low impedance and TiO2 nanotube arrays loaded by Zn 2+could have a decreased resistance.This decrease could likely accelerate the transfer of carriers and even increase photoelectric conversion.

Light Actuation of Liquid in Optofluidics

Optofluidics is the integration of optics and microfluidics(so-called lab on the chip). Wherein the actuation of liquid is a key technic. In a variety of methods for controlling microscale liquid, the light actuation is particularly interesting. The light actuation offers a novel way to control the flow of fluids for biomedical and biotechnological applications, etc.. The complexity and cost of devices sometimes may be greatly reduced by using complete optical control and may be more flexible in operation than other methods. However the light actuation of liquid is a burgeoning field as well as optofluidics. There is lots of work to do. Here we systematically describe four mechanisms for the light actuation of liquid based on the following points: optoelectrowetting, photothermal effect, radiation pressure, photosensitive substance.

Growth Mode Investigation of 3,4,9,10-perylenetetra-carboxylic Dianhydride on p-Si Substrates by X-ray Photoemission Spectroscopy

The growth mode of 3,4,9,10-perylenetetra-carboxylic dianhydride(PTCDA) deposited on p-Si substrates can be deduced by X-ray Photoemission Spectroscopy(XPS). The spectrum and fine spectrum at the surface of specimen are studied. Firstly, PTCDA molecules assemble at the defects to form lots of three-dimensional island-like PTCDA crystal nucleuses, and then by the action of delocalized big π bond, two adjacent layers of PTCDA molecules overlap to some extent and finally island-like structure forms. PTCDA molecules of benzene ring combine with Si atoms at the defects, and that of acid anhydride radicals combine with Si atoms at the perfect fraction of the surface. In the course of combination, although the structure of benzene ring doesn't change, the chemical reaction of acid anhydride radicals and Si occurs to break off C=O bond in acid anhydride, and then C-Si-O and silicon oxide might be produced.

Output Characteristics of Photoelectric Slip Sensor Based on Micro-vibration Detection

In order to achieve the manipulator's soft grasp function, the key is to have slip sensors with fine performance. Depending on the elastomer and photoelectric elements installed in the hand, the sensor transforms the slippage between the grasped object and the robot's hand to electric signal, thus the slippage can be detected. It will cause elastomers' micro-vibration when the object is slippage. Based on the vibration theory, dynamic theory, light intensity theory and elastic deformation theory, derived is the conclusion that the object's slippage acceleration relativing to the robot's hand has linear relationship with the photoelectric elements' output voltage's differential, and then the model for slippage distinguishing is set up.

LONGITUDINAL DISCH.CO_2 LASER WITH PULSED PRE-IONIZATION

A novel pre-ionization scheme of helical transverse-pulsed pre-ionization in a longitudinal discharge CO2 laser is presented. The laser tube is made of glass with inner diameter of 7.5mm and discharge length of 50cm. The laser performance characteristics as functions of parameters, such as pressure, charging capacitance and applied voltage, are investigated. Compared with the same laser structure without pre-ionization, the maximum pulse energy improves by 23%, the optimum electro-optical efficiency increases by 31%, and the specific output energy reaches 26 J/(L·atm).

Energy Spectrum, g Factors, Strain-Induced Level-Splittings and R-Line Thermal Shift of MgO:V^(2+)

Traditional ligand-field theory has to be improved by taking into account both pure electronic contribution and electron-phonon interaction one （including lattice-vibrational relaxation energy）. By means of improved ligand-field theory, the R line, t^322T1 and t^322T2 lines, t^22（^3T1）e^4T2, t^22（^3T1）e^4T1 and t2e^2（^4A2）4T1 bands, g factors of t^32 ^4A2 and t32E, four strain-induced level-splittings and R-line thermal shift of MgO：V^2＋ have been calculated. The results are in very good agreement with the experimental data. It is found that for MgO：V^2＋, the contributions due to electronphonon interaction （EPI） come from the first-order term; the contributions from the second-order and higher terms are insignificant. In thermal shift of R line of MgO：V^2＋, the temperature-dependent contribution due to EPI is dominant. The results obtained in this work may be used in theoretical calculations of other effects of EPI.

Fundamental aspects in CO_(2) electroreduction reaction and solutions from in situ vibrational spectroscopies

Using renewable energy to drive carbon dioxide reduction reaction(CO_(2)RR)electrochemically into chemicals with high energy density is an efficient way to achieve carbon neutrality,where the effective utilization of CO_(2) and the storage of renewable energy are realized.The reactivity and selectivity of CO_(2)RR depend on the structure and composition of the catalyst,applied potential,electrolyte,and pH of the solution.Besides,multiple electron and proton transfer steps are involved in CO_(2)RR,making the reaction pathways even more complicated.In pursuit of molecular-level insights into the CO_(2)RR processes,in situ vibrational methods including infrared,Raman and sum frequency generation spectroscopies have been deployed to monitor the dynamic evolution of catalyst structure,to identify reactive intermediates as well as to investigate the effect of local reaction environment on CO_(2)RR performance.This review summarizes key findings from recent electrochemical vibrational spectrosopic studies of CO_(2)RR in addressing the following issues:the CO_(2)RR mechanisms of different pathways,the role of surface-bound CO species,the compositional and structural effects of catalysts and electrolytes on CO_(2)RR activity and selectivity.Our perspectives on developing high sensitivity wide-frequency infrared spectroscopy,coupling different spectroelectrochemical methods and implementing operando vibrational spectroscopies to tackle the CO_(2)RR process in pilot reactors are offered at the end.

Influence of the Kerr Effect on the Optical Force Acting on the Dielectric Particle

Basing on the necessary condition for the trapping dielectric particle by the Gaussian beam, the Kerr effect in the tweezers with the nonlinear particle or the nonlinear medium is proposed to concern. The expressions of the optical forces concerned with the Kerr effect, which affects the refractive index of the medium, are presented. The distribution of the optical forces in the trapping region is simulated and discussed. The results show that the stability of the tweezers depends on the nonlinear coefficient of refractive index, and the optical tweezers could be broken down with a critical value of the nonlinear coefficient of refractive index of the surrounding medium, or with a critical value of the laser intensity, duration of laser pulse, and radius of beam waist. Moreover, these results give us the explanation the stability of the optical tweezers used for the trapped object as biological molecule embedded in the fluid, which is sensitive with Kerr effect.