教师教学主观能动性的发挥与教育质量

教师主观能动性的发挥表现在“出工”与“出力”两个维度。高校教学质量的提高既有外因又有内因,就教师这一特定主体而言,其对教学质量的影响的内外因的关系正如通常所说的“出工”与“出力”的关系,而内因即“出力”所起的作用更为根本。可以通过内因外化的方式对教学质量提高的内因进行操控,达到提高教育质量的目的。

提高教学质量的内因、外因及其辩证关系的探讨

高校教学质量的提高既有外因又有内因,其间的关系正如通常所说的“出工”与“出力”的关系,而内因所起的作用更为根本。本文探讨建立一个宽松的环境,促进教师自觉主动地进步,提高教学质量,加强参与意识,加强内因所起的作用。同时通过强化外因对教学质量的提高提供保障,从而达到提高教育质量的目的。

Atmospheric oxygen-rich direct leaching behavior of zinc sulphide concentrate

The leaching behavior of main metallic sulphides in zinc concentrate under atmospheric oxygen-rich direct leaching conditions was studied through mineralogical analysis. The results show that the sulphides dissolve obviously except pyrite. Based on the relationship between elemental sulfur and the residual sulphides in the leaching residue, the dissolution of sphalerite, chalcopyrite, covellite and galena is assumed to follow the indirect oxidation reactions, where the acidic dissolution takes place firstly and then the released H2S transfers from the mineral surface into bulk solution and is further oxidized into elemental sulfur. The interface chemical reaction is further supposed as the controlling step in the leaching of these sulphides. The direct electrochemical oxidation reactions are assumed to contribute to the dissolution of pyrrhotite, which is controlled by the diffusion through elemental sulfur layer.

Technological mineralogy and environmental activity of zinc leaching residue from zinc hydrometallurgical process

Chemical, physical, structural and morphological properties of zinc leaching residue were examined by the combination of various detection means such as AAS, XRF, XRD, M？ssbauer spectrometry, SEM-EDS, TG-DSC, XPS and FTIR. The toxicity characteristic leaching procedure （TCLP） was used to investigate the environmental activity of zinc leaching residue for a short contact time. The phase composition analysis indicated that the zinc leaching residue mainly consists of super refined flocculent particles including zinc ferrite, sulfate and silicate. The physical structural analysis showed that it has a thermal instability and strong water absorption properties. The results of TCLP indicated that the amounts of Zn and Cd in the leaching solution exceed 40 and 90 times of limit, respectively, which demonstrate that this residue is unstable in weak acidic environment for a short contact time.

Recovery of indium by acid leaching waste ITO target based on neural network

The optimized leaching techniques were studied by technical experiment and neural network optimization for improving indium leaching rate. Firstly, effect of single technical parameter on leaching rate was investigated experimentally with other parameters fixed as constants. The results show that increasing residual acidity can improve leaching rate of indium. Increasing the oxidant content can obviously increase leaching rate but the further addition of oxidant could not improve the leaching rate. The enhancement of temperature can improve the leaching rate while the further enhancement of temperature decreases it. Extension leaching time can improve the leaching rate. On this basis, a BPNN model was established to study the effects of multi-parameters on leaching rate. The results show that the relative error is extremely small, thus the BPNN model has a high prediction precision. At last, optimized technical parameters which can yield high leaching rate of 99.5%were obtained by experimental and BPNN studies：residual acidity 50-60 g/L, oxidant addition content 10%, leaching temperature 70 ℃ and leaching time 2 h.

Effect of pre-deformation on microstructures and mechanical properties of high purity Al-Cu-Mg alloy

The effects of pre-deformation following solution treatment on the microstructure and mechanical properties of aged high purity Al-Cu-Mg alloy were studied by tensile test, micro-hardness measurements, transmission electron microscopy and scanning electron microscopy. The micro-hardness measurements indicate that compared with un-deformed samples, the peak hardness is increased and the time to reach peak hardness is reduced with increasing pre-strain. Additionally, a double-peak hardness evolution behavior of cold-rolled （CR） samples was observed during aging. The results of TEM observation show that the number density of S′（Al2CuMg） phase is increased and the size is decreased in CR alloy with increase of pre-strain. The peak hardness and peak strength of the CR alloy are increased because of quantity increasing and refinement of S′ phase and high density dislocation.

Effect of normalizing cooling process on microstructure and precipitates in low-temperature silicon steel

Microstructure, precipitate and magnetic characteristic of fmal products with different normalizing cooling processes for Fe-3.2%Si low-temperature hot-rolled grain-oriented silicon steel were analyzed and compared with the hot-rolled plate by optical microscopy （OM）, transmission electron microscopy （TEM）, and energy dispersive spectrometry （EDS）. The results show that, the surface microstructure is uniform, the proportion of recrystallization in matrix increases, and the banding textures are narrowed; the precipitates, whose quantity in normalized plate is more than that in hot-rolled plate greatly, are mainly A1N, MnS, composite precipitates （Cu,Mn）S and so on. Normalizing technology with a temperature of 1120 ℃, holding for 3 min, and a two-stage cooling is a most advantaged method to obtain oriented silicon steel with sharper Goss texture and higher magnetic properties, owing to the uniform surface microstructures and the obvious inhomogeneity of microstructures along the thickness. The normalizing technology with the two-stage cooling is the optimum process, which can generate more fine precipitates dispersed over the matrix, and be beneficial for finished products to get higher magnetic properties.

Influence of land use characteristics and trip attributes on commuting mode choice: a case of Nanjing

The effects of socio-demographics, land use characteristics and trip attributes on the commute mode choice are studied with a nested logit （NL） model. Based on the random utility maximum theory, the NL model is formulated. The analysis is carried out in the main area of Nanjing. Direct and cross elasticities are calculated to analyze the effects of travel time and travel cost on the selection of travel mode choice. The results reveal that the non-motorized travel modes are more attractive in the areas with higher housing and employment accessibility and car owners are found to be more likely to commute to work by car. The bus and subway choice probabilities are more sensitive to changes in travel times than to changes in travel costs. In conclusion, a comprehensive public transit system and effective integration of land use and transportation policies help to relieve the traffic congestion levels caused by the increasing urban sprawl.

Leaching process of rare earths from weathered crust elution-deposited rare earth ore

In order to strengthen the leaching procedure,the chemical processes of leaching rare earths (RE) from the weathered crust elution-deposited rare earth ore were investigated frow the viewpoints of kinetics,hydrodynamic and mass transfer.The results show that the leaching hydrodynamics follows the Darcy law.The leaching kinetics can be described by the shrinking core model;the leaching process is controlled by diffusion of porous solid layer;and the mass transfer can be described with Van Deemter equation.This provides a theoretic basis and a scientific approach with high efficiency and optimized extraction conditions in industrial practice.

Ultrasonic-assisted Oxidation Leaching of Nickel Sulfide Concentrate

The feasibility of oxidation leaching process of nickel from nickel sulfide ore and the form of different components in the lixivium has been studied at first. The method of leaching nickel sulfide concentration directly by oxidants with existence of ultrasonic has been advanced. The process of leaching nickel from nickel sulfide concentration by using the system of persulfate and silver has been determined. The influence of different factors on the leaching rates of nickel,such as with and without ultrasonic,the concentration of Na2S2O8,liquid-solid ratio and the concentration of AgNO3 have been explored. The results show that:(1) in the oxidative leaching system,nickel can be leached completely as Ni2+ or NiSO4(aq.) from nickel sulfide concentration in theory;(2) the nicopyrite can not exist steadily in the persulfate acid leaching system,but Ni2+can. Meanwhile,sulfur may be existed steadily in the leaching process;(3) nicopyrite with much lower electrostatic potential may be leached earlier than chalcopyrite and sideropyrite;and(4) the overall reaction rate of the leaching process can be enhanced with ultrasonic radiation,but it does not change the mechanism of leaching. The more oxidant concentration or higher liquid-solid ratio is,the higher leaching percentage of nickel. The leaching percentage of nickel can be increased significantly by adding a small amount of AgNO3 during the leaching processes. Under the same conditions,the higher concentration of AgNO3 is,the higher leaching yields of nickel will be obtained.

Preparation of pure SbCl_3 from lead anode slime bearing high antimony and low silver

A novel treatment process of lead anode slime bearing high antimony and low silver was developed by a potential-controlled chloridization leaching and continuous distillation.The experimental results show a high Sb 3+ concentration,489.2 g/L,in the leaching solution for two-stage countercurrent leaching process,and the leaching rates of Sb,Cu,Bi more than 99% when the potential is controlled at 450 mV.When the leaching solution is distillated and concentrated at 120°C,almost all the silicon compound is evaporated into the concentration distillate and exists as amorphous hydrated silica.By the continuous distillation,high pure SbCl3 could be prepared,and AsCl3 is enriched in the distillate while metals Bi,Cu are enriched in the continuous distillation residue.As a result,the recovery rate of Sb is more than 95%.

Optimization of brine leaching of metals from hydrometallurgical residue

An orthogonal array,L16(45),was used to examine the effects of four parameters,including NaCl concentration,H2SO4 concentration,temperature and pulp density,on the recovery of Cu,In,Pb and Zn from a hydrometallurgical residue via brine leaching.The results show that temperature of leaching solution has a significant effect on the recovery of Cu,In and Zn,while H2SO4 concentration has an obvious influence on these metals extraction.Both pulp density and NaCl concentration significantly affect Pb extraction.Based on the orthogonal array experiments,the optimum conditions for the extraction of Cu,In,Pb and Zn from hydrometallurgical residue are NaCl concentration of 250 g/L,H2SO4 concentration of 1.00 mol/L,temperature of 85℃,and pulp density of 100 g/L.After 1 h of treatment at these optimum conditions,over 91% of the metals are extracted from the residue.Brine leaching is therefore suitable for the recovery of metals from hydrometallurgical residues.

Extraction of Zinc from Electric Arc Furnace Dust by Alkaline Leaching Followed by Fusion of the Leaching Residue with Caustic Soda

Extractability of zinc from two types of electric arc furnace (EAF) dusts containing 24.8% and 16.8% of zinc respectively (denoted as Sample A and Sample B) were tested using direct alkaline leaching followed by fusion of the resulting leaching residues with caustic soda. The experimental results show that the extraction of zinc is heavily dependent on the contents of iron in the dusts. The higher iron content, the lower extraction of zinc is obtained. 53% and 38% of zinc can be extracted when both dusts were directly contacted with 5mol·L^-1 NaOH solution for 42h. The remaining zinc left in the leaching residues, which supposed to be present as zinc ferrites, can be further leached when the residues were fused with caustic soda. Quantitative extraction of zinc can be obtained from the leaching residue of Sample A while only 85% from Sample B. The extractability of zinc from dusts wit hvarious contents of iron is compared. The production flowsheet for zinc from the dusts using the process proposed is discussed.

Recovery prediction of copper oxide ore column leaching by hybrid neural genetic algorithm

The artificial neural network(ANN)and hybrid of artificial neural network and genetic algorithm(GANN)were appliedto predict the optimized conditions of column leaching of copper oxide ore with relations of input and output data.The leachingexperiments were performed in three columns with the heights of2,4and6m and in particle size of<25.4and<50.8mm.Theeffects of different operating parameters such as column height,particle size,acid flow rate and leaching time were studied tooptimize the conditions to achieve the maximum recovery of copper using column leaching in pilot scale.It was found that therecovery increased with increasing the acid flow rate and leaching time and decreasing particle size and column height.Theefficiency of GANN and ANN algorithms was compared with each other.The results showed that GANN is more efficient than ANNin predicting copper recovery.The proposed model can be used to predict the Cu recovery with a reasonable error.

Analysis of the dialectical relation between top coal caving and coal-gas outbtu rst

According to the different engineering mechanical states of top coal caving andnormal stoping of gaseous loose thick coal seams,the dialectical relation between thiscaving method and dynamic disasters was analyzed by simulating the change of stressstates in the process of top coal initial caving with different mining and caving ratios basedon the ANSYS10.0.The variation of elastic energy and methane expansion energy duringfirst top coal caving was analyzed by first weighting and periodic weighting and combiningwith coal stress and deformation distribution of top coal normal stoping as well as positiveand negative examples in top coal caving of outburst coal seam.The research shows thatthe outburst risk increases along with the increase of the caving ratio in the initial miningstage.In the period of normal stoping,when the mining and caving ratio is smaller than1:3 and hard and massive overlying strata do not exist (periodic weighting is not obvious),it is beneficial to control ground stress leading type outburst.Thus,it is unreasonable toprohibit top coal caving in dangerous and outburst prone areas.

A primary study of simultaneous leaching of silver containing manganese ore and a sphalerite concentrate

It is demonstrated that a low grade, silver containing manganese deposit can be exploited by reaction with a ZnS concentrate. In the process, Mn(IV) is reduced to Mn(II) and the ZnS converted to ZnSO4. In the process, Mn and Zn are solubilized. By studying the effects of quantity of reducing agent and sulfuric acid added and of time, temperature and liquid-to-solid ratio on the leaching process, the optimum technological conditions have been achieved under which the amount of manganese leached was 98 %. The silver can be removed from remaining solids by adding ammonia liquor. Then by adding hydrazine hydrate, sponge silver with purity up to 99 % can be obtained with a recovery of 87 %.

Comparative studies on hydrometallurgical treatment of smelted low-grade electronic scraps for selective copper recovery

A comparison of three hydrometallurgical methods for selective recovery of copper from low-grade electric and electronic wastes was reported. Scraps were smelted to produce Cu？Zn？Sn？Ag alloy. Multiphase material was analyzed by SEM？EDS and XRD. The alloy was dissolved anodically with simultaneous metal electrodeposition using ammoniacal and sulfuric acid solutions or leached in ammonia？ammonium sulfate solution and then copper electrowinning was carried out. This resulted in the separation of metals, where lead, silver and tin accumulated mainly in the slimes, while copper was transferred to the electrolyte and then recovered on the cathode. The best conditions of the alloy treatment were obtained in the sulfuric acid, where the final product was metal of high purity （99% Cu） at the current efficiency of 90%. Ammoniacal leaching of the alloy led to the accumulation of copper ions in the electrolyte and further metal electrowinning, but the rate of the spontaneous dissolution was low. Anodic dissolution of the alloy in the ammonia？ammonium sulfate solution led to the unfavorable distribution of metals among the slime, electrolyte and cathodic deposit.

Top-cited Articles in Chemical Engineering in Science Citation Index Expanded:A Bibliometric Analysis

This study aimed to identify and to analyze characteristics of top-cited articles published in the Web of Science chemical engineering subject category from 1899 to 2011.Articles that have been cited more than 100 times were assessed regarding publication outputs,and distribution of outputs in journals.Five bibliometric indicators were used to evaluate source countries,institution and authors.A new indicator,Y-index,was created to assess quantity and quality of contribution to articles.Results showed that 3828 articles,published between 1931 and 2010,had been cited at least 100 times.Among them 54% published before 1991,and 49% top-cited articles originated from US.The top eight productive institutions were all located in US.The top journals were Journal of Catalysis,AIChE Journal,Chemical Engineering Science and Journal of Membrane Science.Y-index was successfully applied to evaluate publication character of authors,institutions,and countries/regions.

Cyclic metallurgical process for extracting V and Cr from vanadium slag: Part Ⅱ. Separation and recovery of Cr from vanadium precipitated solution

Cyclic metallurgical process for separation and recovery of Cr from vanadium precipitated solution by precipitation with PbCO_(3)and leaching with Na_(2)CO_(3)was investigated.The concentration of Cr residue in the solution decreases from 2.360 to 0.001 g/L by adding PbCO_(3)into vanadium precipitated solution according to Pb/Cr molar ratio of 2.5,adjusting the pH to 3.0 and stirring for 180 min at 30℃.Then,the precipitates were leached with hot Na_(2)CO_(3)solution to obtain leaching solution containing Na_(2)CrO_(4)and leaching residue containing PbCO_(3).The leaching efficiency of Cr reaches 96.43%by adding the precipitates into 0.5 mol/L Na_(2)CO_(3)solution with the mass ratio of liquid to solid(L/S)of 10:1 mL/g and stirring for 60 min under pH 9.5 at 70℃.After filtration,leaching residue is reused in Cr precipitation and leaching solution is used to circularly leach the Cr precipitates until Na_(2)CrO_(4)approaches the saturation.Finally,the product of Na_(2)CrO_(4)·4H_(2)O is obtained by evaporation and crystallization of leaching solution.

Principle and engineering application of pressure relief gas drainage in low permeability outburst coal seam

With the increase in mining depth, the danger of coal and gas outbursts increases.In order to drain coal gas effectively and to eliminate the risk of coal and gas outbursts, we used a specific number of penetration boreholes for draining of pressure relief gas.Based on the principle of overlying strata movement, deformation and pressure relief, a good effect of gas drainage was obtained.The practice in the Panyi coal mine has shown that, after mining the C11coal seam as the protective layer, the relative expansion deformation value of the protected layer C13 reached 2.63%, The permeability coefficient increased 2880 times, the gas drainage rate of the C13 coal seam increased to more than 60%, the amount of gas was reduced from 13.0 to 5.2 m3/t and the gas pressure declined from 4.4 to 0.4 MPa, which caused the danger the outbursts in the coal seams to be eliminated.The result was that we achieved a safe and highly efficient mining operation of the C13 coal seam.