将刷机进行到底 三星手机发烧友谈“刷机”

01 小编:曹老师是什么时候与三星结“缘”的呢?你的第一部手机是三星吗? 一直以来我都对三星手机情有独钟,一是因为三星手机的水货软件比其它牌子的容易弄到,可以不断刷机(笑),二是由于我很喜欢三星手机的风格以及其精湛的制造技术(用过那么多三星机子,没有一部坏过),三是因为三星机子的可玩性比较好,

个性无极限 手把手教你“刷”三星手机

“刷机”一直是三星手机发烧友津津乐道的疾题，可是到底什么是什么“刷机”一般是针对三星水货机型所提出的概念，对比行货机型，水货机型的软件稳定性不是很，有的机型甚至存在比较大的BUG，于是就出现了“刷机”可以用更新、更稳定的软件刷入手机，替代之前旧版本软件。普通的“刷机”在备份了原有软件后，只是将新软件通过数据线刷入手机，今天我们进行的工作更为“复杂”，是通过修改原有软件置换新的铃声，再刷回手机。

STRATEGY AND IMPLEMENTATION FOR HIGH-SPEED TORQUE ENHANCEMENT OF BRUSHLESS DC MOTOR

Serious commutation lag occurs when a Brushless DC Motor(BLDCM) operates at high speeds,and this leads to torque decline with ripple.In this paper,an advanced conduction control scheme is proposed which can accelerate the commutation and enhance the torque production remarkably.Besides,an on line adjusting algorithm based on the Golden Section Method is adopted to search the optimal advanced conduction angle.Simulation and experimental results verify the feasibility and effectivity of the scheme proposed.

Anti-reverse rotation startup method for sensorless brushless DC motor

In order to start up the brushless DC motor （BLDCM） without reverse rotation and smoothly switch the running state of the motor, a novel startup and smoothly switching method for a sensodess BLDCM is presented. Based on the saturation effect of the stator iron, six short voltage pulses are applied to determine the initial rotor position and the rotor can be found within 60°. After that, a series of short and long voltage pulses are used to accelerate the motor and the variation of the response current is utilized to detect the rotor position dynamically. When the motor reaches a certain speed at which the back-electromotive force （EMF） method can be applied, all the power devices are turned off and the running state of the motor is smoothly switched at the moment determined by the relationship between the terminal voltage waveform and the commutation phases. The experimental results verify the feasibility and validity of the proposed method.

EFFECTIVE DOUBLE LOOP CONTROL FOR A SQUARE WAVE BRUSHLESS DC MOTOR

A new type of brushless DC motor has been developed by using a square wave rare earth permanent magnet synchronous motor with its double loop control circuit. The double loop control scheme of the drive system yields a combination of desired characteristics including simplified control structure, small ripple torque, high speed accuracy, wide operating speed range, and fast dynamic response. Experimental results confirm excellent characteristics of the motor.

Integrated design of brushless motor drive and control system for robot joints

To meet the requirements of high performance, low cost, and easy operation of the robot, a brushless motor drive and control system for the robot joint is designed, including CAN bus, WPF upper host computer development, and magnetic encoders, and other sensors, in which the STM32 F103 chip is used as the main control chip, and the DRV8323 is a brushless motor drive chip. The principle of field-oriented control(FOC) brushless motor drive is elaborated.Meanwhile, the drive and control system design is completed from both hardware and software aspects. Finally, the PID algorithm is used for the closed-loop speed test of the robot joint. The experimental result shows that the designed robot joints and control system run smoothly and reliably, have the characteristics of modularization and miniaturization, and are suitable for the control of micro-service robots and manipulators.

Calculation of impact factor of vibrator oscillation in offset printing based on fuzzy controller and genetic algorithm

In the inking system of an offset printing press,a vibrator roller distributes ink not only in the circumferential direction but also in the axial direction.In the control process,if ink amount is determined only by the dot area coverage without considering the impact of vibrator roller's oscillation,the printing colour quality will be reduced.This paper describes a method of calculating the impact factor of vibrator roller' s oscillation.First,the oscillation performance is analyzed and sample data of impact factor is got.Then,a fuzzy controller used for the calculation of the impact factor is designed,and genetic algorithm is used to optimize membership functions and obtain the fuzzy control rules automatically.This fuzzy controller can be used to calculate impact factors for any printing condition,and the impact factors can be used for ink amount control in printing process and it is important for higher printing colour quality and lowering ink and paper waste.

A New-style Permanent-magnet Motor with Double-stator Structure

A new-style direct drive motor with double-stator structure is proposed. The structure and principle of the permanent-magnet (PM) brushless motor are discussed. On the basis of numerical calculation, the cogging torque waveforms of the prototype motor when staggering two stators are analyzed. The method that can reduce torque ripple making use of the structure features of this motor is investigated. The results of numerical calculation and experiment indicate that designing motor with this kind of structure is a good scheme for increasing the power density.

Recovering metals from printed circuit board scrap by a mechanical separation process

A mechanical separation process was developed for recovering metals from printed circuit board(PCB) scrap;it included three steps:impact crushing,sieving and fluidization separation.The mechanism of the technique was based on the difference in the crushabilities of metallic and nonmetallic materials in the PCBs that led to the concentrated distribution of metals in particles of larger sizes and nonmetals mostly in particles of smaller sizes.It was found that crushed PCB particles from 0.125 mm to 1.000 mm contained about 80% of metals in the PCBs.Metals acquired satisfactory liberation in particles smaller than 0.800 mm.The crushed PCB particles were sieved into fractions of different size ranges.Each fraction separately went through a gas-solid fluidized bed operating at a selected optimal gas velocity for the specific size range.Approximately 95% of metals in printed circuit board particles from 0.125 mm to 0.800 mm was recovered by the gas-fluidized bed separator at the selected optimal gas velocity.However,separation of metals from particles smaller than 0.125 mm was not satisfactory.Further study is needed on metal recovery from fine particles.

Steady-State Performance Analysis of Brushless DC Propulsion Motor

The brushless DC motor can be used in the marine electric propulsion system for its excellent control characteristics and large thrust. In order to estimate the operating performances of the brushless DC motor for the high-power shipping during the design stage, the steady-state analysis is as important as the dynamic analysis generally. A mathematical model of the brushless DC propulsion motor is established according to the state-space method for the dynamic and steady-state performance analysis. The state-space mathematical model is a set of linear differential equations, so the steady-state currents of the armature windings can be gained directly by the symmetrical boundary conditions and the eigenvalues of the system matrix. The steady-state simulation results are compared with the dynamic ones to validate the correctness of this eigenvector method.

Design of a novel finger of DLR/HIT dextrous robot hand based on mechatronic integration

With the idea of mechatronic integration,a novel finger of the dextrous robot hand has been designed. The finger with nice envelop has four joints with three DOFs driven by three brushless DC motors with smaller size and more torque. The use of rigid gear head,bevel gears and linkage in the transmission system makes the finger more rigid. Abundant sensors such as joint angle sensors,joint torque sensors and temperature sensors are located in the finger. Integration and modularization are achieved at most by high integration of finger body,driving system,sensors and electronics.

Properties of Brushless DC Machine Induced by Permanent Magnets Applied to a Traction Drive

The paper presents a mathematical model ofbrushless DC machine induced by permanent magnets. Its construction uses the classical model of permanent magnet synchronous machine and induced model of power inverter using the serraphil form. The results of the computer simulation were presented for such states： startup, work under active constant load and the behavior of the machine in terms of exponential and stepping change of the power inverter＇s control angle.

Modern Control and Diagnostic System of Traction Vehicle with Hybrid Drive System

In paper it introduced a review of modem traction vehicle drive system with induction motor drive system （PMSM with single or dual rotor drive system） or BLDC motor with different configuration of magnetic circuits. For particular part of drive system proposed a quasi intelligent control system version smart control enables multi criteria predictive control of vehicle work. In the paper presented also a selected diagnostic procedure, enables monitoring exploitation parameters, and prediction of probable failure state. For different vehicle work state realized a simulation models and crash test of exploitations failure models.

Brushless Doubly-Fed Induction Machine as a Variable Frequency Transformer

VFT （variable frequency transformer） has been recently used as art alternative to HVDC （high voltage direct current） to control power flow between asynchronous networks. VFT consumes less reactive power than a back-to-back HVDC system, provides faster initial transient recovery, and has better natural damping capability. VFT is simply a DFIM （doubly-fed induction machine） where the machine torque controls the power flow from stator to rotor and vice versa. The main disadvantage of this VFT is the slip rings and brushes required for the rotor circuit, especially in bulk power transmission. The BDFM （brushless doubly-fed machine） with nested cage rotor machine is proved to be a comparable alternative to conventional DFIM in many applications with the advantage that all windings being in the stator frame with fixed output terminals. In this paper, the BDFM is used as a BVFT （brushless variable frequency transformer）. A prototype machine is designed and simulated to verify the system validity.

Methodology for Precious Metal Recovery in Computer Printed Circuit

The life of electronic equipment is becoming increasingly shorter and its replacement always generates a quantity of waste increase, giving rise to a problem of environmental character and still needed new options of solid waste management that will contribute to global sustainable development. Parts of these waste are TCI （the card＇s printed circuit） which containing dangerous elements and turns them into a polluting material from the soil, water and air, being harmful to human health if there is to proper and responsible way, so the recycling of TCI to obtain precious metals is an example of industrial materials that can be recycled. Despite this, large quantities of these are not recycled and some others are not considered. The objective of this work is to present a systematic and ecological methodology for the recovery of valuable materials contained in parts of used in computers, circuit boards using a leaching process. The method determines a set of variables to evaluate the kinetics of the reaction and the leaching of metals that form the substrate of metal and to establish the parameters that affect the rate of leaching of metals through a sensitivity analysis, to identify design alternatives. It determines the quantity and percentages that constitutes the motherboard, processor, video cards, accelerator graphics, network and memory cards RAM, among others and its content of metals such as Cu, Fe, Ag, Au and Pt.

Sensorless Predictive Algorithm for Permanent Magnet Brushless DC Drives

A high resolution speed and position identification algorithm, suitable for brushless DC drives, is presented in this paper. In particular, the algorithm is proposed for BLDC （brushless DC） machines that are characterized by an un-ideal trapezoidal emfs shape. The algorithm, which is developed basing upon the MRAS technique （model reference adaptive system） and the Popov＇s hyperstability criterion, guarantees the convergence of the estimated rotor speed and position signals to their corresponding actual values. The identification procedure can be performed starting from the knowledge of low resolution rotor position signals, phase currents and the BLDC emfs shape. The identification algorithm is properly tested on a BLDC drive controlled by a predictive algorithm, by performing a simulation study in the Matlab-Simulink environment. The corresponding results have highlighted the effectiveness of the proposed sensorless predictive control system, at both low and high speed operation.

Mechanism of Downcutting Erosion of Debris Flow over a Movable Bed

The phenomenon of debris flow is intermediate between mass movement and solid transport. Flows can be sudden, severe and destructive. Understanding debris flow erosion processes is the key to providing geomorphic explanations, but progress has been limited because the physical-mechanical properties, movement laws and erosion characteristics are different from those of sediment-laden flow. Using infinite slope theory, this research examines the process and mechanism of downcutting erosion over a moveable bed in a viscous debris flow gully. It focuses specifically on the scour depth and the critical slope for viscous debris flow,and formulas for both calculations are presented.Both scour depth and the critical conditions of downcutting erosion are related to debris flow properties(sand volume concentration and flow depth) and gully properties(longitudinal slope,viscous and internal friction angle of gully materials,and coefficient of kinetic friction). In addition, a series of flume experiments was carried out to characterize the scouring process of debris flows with different properties. The calculated values agreed well with the experimental data. These theoretical formulas are reasonable, and using infinite slope theory to analyze down cutting erosion from viscous debris flow is feasible.

Highly Effective Brushless DC Motor in Which Unidirectional Current Flows in

Authors developed a highly effective brushless DC motor with a simple operation principle. If the operation principle of the motor is simple, a drive circuit will also become simple and its production cost will be lower. From the above fact, Minato motor was noticed. In this motor, a unidirectional current flows in the electromagnets. In other words, unidirectional windings are used. In this motor, only strong repulsive force is utilized when a permanent magnet of a rotor and an electromagnet of a stator are adjacent. Hence, torque constant becomes higher and the efficiency of the motor is high. However, an effective value of the electromagnetic current increases because a large current flows in a short period. Therefore, copper loss increases and the efficiency of the motor decreases. In order to solve above defects, a new motor is proposed. From the experiment, it is clarified that the efficiency of the proposed motor is higher than that of the commercial motors.

Process and Manufacturing of Ceramic Pattern and Its Digital Analysis by Computer

This paper compares Ceramic Decal design and traditional printing design through computer; show the innovation advantages of computer Ceramic Decal design prominent, such as computer color advantage, computer design software brings innovation advantage. The computer brings to the thinking innovation advantage and computer Ceramic Decal design than the traditional ceramic decal in the design process. Through the design advantage that computer has very important influence and significance of ceramic decal.

Study on the Thermal and Mechanical Properties of the UV-cured SL5510 Stereolithography Material

In recent years, Vantico A &T US Incorporation has developed a type of the hightest accuracy photosensitive resin: SL5510 stereolithography material(briefly named SL5510) to use in the stereolithography apparatus(SLA). In this paper, the thermal and mechanical properties were investigated for the fabricated specimens of SL5510 in the different UV post-cure time. This may instruct us to employ better the fabricated parts of SL5510.