Polyether ether ketone(PEEK)has good mechanical properties.However,its high viscosity when molten limits its use because it is hard to process.PEEK nanocomposites containing both carbon nanotubes(CNTs)and polyether im...Polyether ether ketone(PEEK)has good mechanical properties.However,its high viscosity when molten limits its use because it is hard to process.PEEK nanocomposites containing both carbon nanotubes(CNTs)and polyether imide(PEI)were pre-pared by a direct wet powder blending method using a vertical injection molding machine.The addition of an optimum amount of PEI lowered the viscosity of the molten PEEK by approximately 50%while producing an increase in the toughness of the nanocom-posites,whose strain to failure increased by 129%,and fracture energy increased by 97%.The uniformly dispersed CNT/PEI powder reduced the processing difficulty of PEEK nanocomposites without affecting the thermal resistance.This improvement of the strength and viscosity of PEEK facilitate its use in the preparation of thermoplastic composites.展开更多
The influence of supercooled melt forced lamina flow on microsegregation was investigated. The concentration distribution at solid-liquid boundary of binary alloy Ni-Cu was simulated using phase field model coupled wi...The influence of supercooled melt forced lamina flow on microsegregation was investigated. The concentration distribution at solid-liquid boundary of binary alloy Ni-Cu was simulated using phase field model coupled with flow field. The microsegregation, concentration maximum value, boundary thickness of concentration near upstream dendrite and normal to flow dendrite, and downstream dendrite were studied quantitatively in the case of forced lamia flow. The simulation results show that solute field and flow field interact complexly. Compared with melt without flow, in front of upstream dendrite tip, the concentration boundary thickness is the lowest and the concentration maximum value is the smallest for melt with flow. However, in front of downstream dendrite tip, the results are just the opposite. The zone of poor Cu in upstream dendrite where is the most severely microsegregation and shrinkage cavity is wider and the concentration is lower for melt with flow than that without flow.展开更多
The effects of cooling rate on the solidification parameters and microstructure of Al-7Si-0.3Mg-0.15 Fe alloy during solidification process were studied.To obtain different cooling rates,the step casting with five dif...The effects of cooling rate on the solidification parameters and microstructure of Al-7Si-0.3Mg-0.15 Fe alloy during solidification process were studied.To obtain different cooling rates,the step casting with five different thicknesses was used and the cooling rates and solidification parameters were determined by computer-aided thermal analysis method.The results show that at higher cooling rates,the primary α(Al) dendrite nucleation temperature,eutectic reaction temperature and solidus temperature shift to lower temperatures.Besides,with increasing cooling rate from 0.19 ℃/s up to 6.25 ℃/s,the secondary dendritic arm spacing decreases from 68 μm to 20 μm,and the primary dendritic volume fraction declines by approximately 5%.In addition,it reduces the length of Fe-bearing phase from 28 μm to 18 μm with a better uniform distribution.It is also found that high cooling rates make for modifying eutectic silicon into fibrous branched morphology,and decreasing block or lamella shape eutectic silicon.展开更多
Morphology and crystal structure of β precipitate phase in Mg-7Gd-5Y-1Nd-0.5Zr (mass fraction, %) alloy were characterized by optical microscopy, scanning electron microscopy and transmission electron microscopy. Com...Morphology and crystal structure of β precipitate phase in Mg-7Gd-5Y-1Nd-0.5Zr (mass fraction, %) alloy were characterized by optical microscopy, scanning electron microscopy and transmission electron microscopy. Compositions were determined for β phase using thin foil energy dispersive spectroscopy. Precipitation at 400 ℃ involves formation of platelet and block-shaped β phase. The orientation relationship is and between β precipitate phase and α-Mg matrix with habit planes parallel to , and a composition of Mg5(Y0.4Gd0.4Nd0.2) is suggested for the β phase in Mg-7Gd-5Y-1Nd-0.5Zr alloy.展开更多
In this study,different influence mechanisms associated with temperatures and pH values were investigated through cemented paste backfill(CPB)systems.CPB samples were prepared with temperatures ranging from 10 to 50℃...In this study,different influence mechanisms associated with temperatures and pH values were investigated through cemented paste backfill(CPB)systems.CPB samples were prepared with temperatures ranging from 10 to 50℃ in 10℃ increments and pH values of 3,7,and 13.Then,the CPB mixture were subjected to rheological tests,thermogravimetric analysis(TG),derivative thermogravimetry analysis(DTG),Fourier-transform infrared spectroscopy(FT-IR),and scanning electron microscopy(SEM).Results demonstrated that the temperatures had significant effects on the rheological properties of CPB,whereas the effects of pH values were relatively unapparent.Higher temperatures(over 20℃)were prone to bring higher shear stress,yield stress,and apparent viscosity with the same pH value condition.However,an overly high temperature(50℃)cannot raise the apparent viscosity.Non-neutral conditions,for pH values of 3 and 13,could strengthen the shear stress and apparent viscosity at the same temperature.Two different yield stress curves could be discovered by uprising pH values,which also led to apparent viscosity of two various curves under the same temperatures(under 50℃).Microscopically,rheological properties of CPB were affected by temperatures and pH values which enhanced or reduced the cement hydration procedures,rates,products and space structures.展开更多
Multicellular magnetotactic prokaryotes (MMPs) are a group of aggregates composed of 7-45 gram-negative cells synthesizing intracellular magnetic crystals. Although they are thought to be globally distributed, MMPs ...Multicellular magnetotactic prokaryotes (MMPs) are a group of aggregates composed of 7-45 gram-negative cells synthesizing intracellular magnetic crystals. Although they are thought to be globally distributed, MMPs have been observed only in marine environments in America and Europe. Most MMPs share a rosette-like morphology and biomineralize iron sulfide crystals. In the present study, abundant MMPs were observed, with a density of 26 ind./cm^3, in the sediments of a coastal lagoon, Lake Yuehu, in the Yellow Sea. Optical microscopy showed that all of them were rosette shaped with a diameter of 5.5±0.8 μm. Transmission electron microscopy revealed that these MMPs were composed of 10- 16 ovoid cells and flagellated peritrichously. High-resolution transmission electron microscopy and energy dispersive X-ray analysis indicated that they biomineralized bullet-shaped magnetite crystals in highly organized parallel chains within which the magnetosomes were oriented in the same direction. This is the first report of MMPs from Asia and demonstrates the ubiquitous distribution of MMPs.展开更多
A series of researches were carried out for the soil samples in the Pearl River Delta under the action of consolidation loads,such as the quantitative analyses of the pore scale,shape and size distributions of micro-s...A series of researches were carried out for the soil samples in the Pearl River Delta under the action of consolidation loads,such as the quantitative analyses of the pore scale,shape and size distributions of micro-structure units,with an environmental scanning electron microscope (ESEM),a mercury intrusion analyzer and a mineral diffractometer. The experimental results show that the consolidation pressures remarkably change the pore sizes and distribution characteristics of the silt,thus changing its compressibility and permeability. This can be proved by the fact that,in the earlier stage with a consolidation pressure of p<200 kPa,the pore sizes are greater and the compressibility and permeability coefficients are larger. However,they rapidly decrease with the increase in consolidation pressure. And in the later stage with a consolidation pressure of p>200 kPa,the pore sizes are smaller and the compressibility and permeability coefficients are less. Therefore,the empirical formulas of compression coefficient and permeability coefficient vs consolidation load and average pore diameter are deduced.展开更多
The effect of an ultrasonic field on the microstructure and mechanical properties of 7085 aluminum alloy during solidification was investigated by optical microscopy, Vickers hardness test, tensile test, scanning elec...The effect of an ultrasonic field on the microstructure and mechanical properties of 7085 aluminum alloy during solidification was investigated by optical microscopy, Vickers hardness test, tensile test, scanning electron microscopy (SEM) with energy dispersive X-ray spectrometry, and electron probe micro-analysis (EPMA). The results showed that the grains of aluminum alloy were significantly refined and secondary phases were dispersed and distributed uniformly at the grain boundaries, due to ultrasonic treatment (UST). By EPMA, it was observed that the distribution of the main elements A1, Zn, Mg and Cu was more homogeneous in alloys with UST, than in alloys without UST. The mechanical properties of the aluminum alloy also significantly improved. As demonstrated by the SEM fractography of the fractured faces of several castings, fracture of the unrefined specimens occurred in a brittle manner, whereas the cracks of the refined specimens showed quasi-cleavage fracture.展开更多
In view of the mechanics characteristic of cemented tailings backfill(CTB)at early age,the separation Hopkinson pressure bar test device was used to explore the effects of curing age and impact energy.A total of 48 CT...In view of the mechanics characteristic of cemented tailings backfill(CTB)at early age,the separation Hopkinson pressure bar test device was used to explore the effects of curing age and impact energy.A total of 48 CTB samples with diameter of 50 mm and length of 25 mm were prepared with curing ages of 3,5,7 and 9 d.Impact tests under different impact energy(10,20,30 and 40 J)were carried out.The microstructure of CTB at different ages was analyzed by scanning electron microscopy(SEM).The results show that,the curing age mainly affects the mechanical properties and internal structure of early-age CTB.With increasing curing age,the mechanical properties of early-age CTB change from viscoelasticity to brittleness.The impact energy mainly affects the response of dynamic peak compressive strength to strain rate.Under low strain rate,the structure of CTB is broken,but still has bearing capacity,affecting the formation of later strength.It is concluded that the structural loses completely under the action of high strain rate.Therefore,the control of impact energy and the protection of curing age should be fully considered in actual production process.展开更多
The damage process of concrete exposed to sodium sulfate attack and drying-wetting cycles was investigated. The water to binder(W/B) ratio and the concentration of sulfate solution were taken as variable parameters. T...The damage process of concrete exposed to sodium sulfate attack and drying-wetting cycles was investigated. The water to binder(W/B) ratio and the concentration of sulfate solution were taken as variable parameters. Through the experiment, visual change, relative dynamic modulus of elasticity(RDME) and the surface damage layer thickness of concrete were measured.Furthermore, SEM and thermal analysis were used to investigate the changing of microstructure and corrosion products of concrete.The test results show that the ultrasonic velocity is related to the damage layer of concrete. It approves that an increase in damage layer thickness reduces the compactness and the ultrasonic velocity. The deterioration degree of concrete could be estimated effectively by measuring the surface damage layer and the RDME of concrete. It is also found that the content of gypsum in concrete is less than that of ettringite in test, and some gypsum is checked only after a certain corrosion extent. When the concrete is with high W/B ratio or exposed to high concentration of sulfate solution, the content of ettringite first increases and then decreases with corrosion time. However, the content of gypsum increases at a steady rate. The content of corrosion products does not correspond well with the observations of RDME change, and extensive amount of corrosion products can be formed before obvious damage occurs.展开更多
The mechanical properties of cemented paste backfill(CPB) depend heavily on its pore structural characteristics and micro-structural changes. In order to explore the variation mechanisms of macro-mechanical characteri...The mechanical properties of cemented paste backfill(CPB) depend heavily on its pore structural characteristics and micro-structural changes. In order to explore the variation mechanisms of macro-mechanical characteristics and micro-structure of CPB. CPB specimens with different mass concentrations prepared from the full tailings of Xianglushan Tungsten Ore were micro-tests. Moreover, acquired pore digital images were processed by using the pores(particles) and cracks analysis system(PCAS), and a sensitivity analysis was performed. The results show that as the mass concentration of CPB increases from 70% to 78%, the porosity, the average pore area and the number of pores drop overall, leading to a decline in the pores opening degree and enhancing the mechanical characteristics. As the mass concentration of CPB increases, the trend of fractal dimension, probability entropy and roundness is reduced, constant and increased, which can result in an enhancement of the uniformity, an unchanged directionality and more round pores. According to the definition of sensitivity, the sensitivities of various micro-parameters were calculated and can be ranked as porosity > average pore area > number of pores > roundness > fractal dimension > probability entropy.展开更多
Semi-solid metal processing is being developed in die casting applications to give several cost benefits. To efficiently apply this emerging technology, it is important to understand the evolution of microstructure in...Semi-solid metal processing is being developed in die casting applications to give several cost benefits. To efficiently apply this emerging technology, it is important to understand the evolution of microstructure in semi-solid slurries for the control of the theological behavior in semi-solid state. An experimental apparatus was developed which can capture the grain structure at different times at early stages to understand how the semi-solid structure evolves. In this technique, semi-solid slurry was produced by injecting fine gas bubbles into the melt through a graphite diffuser during solidification. Then, a copper quenching mold was used to draw some semi-solid slurry into a thin channel. The semi-solid slurry was then rapidly frozen in the channel giving the microstructure of the slurry at the desired time. Samples of semi-solid 356 aluminum alloy were taken at different gas injection times of 1, 5, 10, 15, 20, 30, 35, 40, and 45 s. Analysis of the microstructure suggests that the fragmentation by remelting mechanism should be responsible for the formation of globular structure in this rheocasting process.展开更多
Although the first microscopic observations on soils date already from the beginning of the twentieth century, the publication of Kubiena's book "Micropedology" in 1937 is considered as the beginning of this new sc...Although the first microscopic observations on soils date already from the beginning of the twentieth century, the publication of Kubiena's book "Micropedology" in 1937 is considered as the beginning of this new scientific discipline. This first system for micromorphological descriptions of soils is considered as morphoanalytical, analysing the fabric according to pure morphological criteria. In a second period Kuniena used a morphogenetic approach, directly relating the global observed fabric to genetic soil horizons. This system, mainly limited to European soils, was in general use till the early nineteen-seventies. End of the nineteen-fifties non- genetic soil classification systems were developed (e.g. USDA). This trend prompted R. Brewer to publish in 1964 a new morphoanalytical system for fabric analysis, used till the end of last century. Because of some inconsistencies in this approach, a working group of the ISSS published in 1985 a new set of morphoanalytical concepts and associated terminology (Bullock et al.), in 2003 adapted and extended by Stoops. Several morphosynthetic systems, expressing a complete soil microfabric in a single (compound) term have been proposed, but none was really successful. In 1967 Kubiena introduced the term "micromorphometry" to name a new branch of micromorphology quantifying the soil fabric, mainly evaluating changes in porosity and structure resulting from soil management. The necessity of dearly defined concepts and terms for fabric analysis of soils and regoliths, even as a need for standardisation of quantitative methods, are discussed in the conclusions.展开更多
The chemical compositions,mineralogical characteristics,as well as dissemination of iron-and phosphorus-based minerals were studied for the E’xi oolitic hematite from western Hubei Province in China by using chemical...The chemical compositions,mineralogical characteristics,as well as dissemination of iron-and phosphorus-based minerals were studied for the E’xi oolitic hematite from western Hubei Province in China by using chemical analysis,optical microscope,electron probe micro-analyzer(EPMA)and energy dispersive spectroscopy(EDS).It is found that this kind of oolitic hematite ore contains 47.71%TFe,10.96%SiO_2,as well as 0.874%P,with hematite as the dominant Fe-bearing minerals,and quartz,chamosite,illite and cellophane as main gangue minerals.The microscope examination showed that the ore has an oolitic structure,with some ooids principally formed by a series of concentric layers of hematite collophanite around nucleus that is hematite in the association with collophanite.Based on the EPMA and EDS analysis,it can be known that some ooids are primarily composed of hematite and collophanite.The separation can be achieved through fine grinding for those collophanite laminae with a higher P content.However,the dissemination of two minerals at the interface will result in the difficulty in effective separation.Besides,some ooids are made of chamosite with some nucleus formed of quartz,which is principally finely disseminated with hematite.In view of the close association and dissemination of iron-and phosphorus-based minerals in the ooids,it is found that the process of stage-grindings and stage-separations can be adopted to effectively increase the iron recovery and decrease the P content in the concentrate to some extent.展开更多
The finite element model is established according to the experimental results,and then the experimental results are verified by simulation calculation.In terms of the combination of finite element analysis and experim...The finite element model is established according to the experimental results,and then the experimental results are verified by simulation calculation.In terms of the combination of finite element analysis and experiment,the effect of particle size of CuO and SnO_(2) on the stress,strain and microstructure of AgCuOSnO_(2) composite during hot extrusion was studied.The results illustrate that with the decrease of particle size,the dispersion of the second phase increases gradually,while the possibility of“tail shrinkage”of the billet decreases continuously;cubic CuO will evolve to fibrosis,and the degree of fibrosis will increase with the decrease of the particle size and ring clusters.Specifically,the degree of fibrosis at the middle end of the billet is higher than that at the front end,the degree of fibrosis at the front end is higher than that at the back end,and the degree of fibrosis on the surface is higher than that in the core;part of CuO fibers will bend,and the degree of buckling strength is positively correlated with the size of particles and their annular clusters.Additionally,there is fiber CuO in the front and back end of the billet that are inconsistent with the extrusion direction,and the degree of difference was negatively correlated with the particle size.展开更多
The aim of this work is evaluate the intergranular corrosion on UNS S31803 steel, with heat treatments at 800 ℃, varying treatment times of 30 mins, 360 mins and 1,440 mins. The results confirm the formation of o pha...The aim of this work is evaluate the intergranular corrosion on UNS S31803 steel, with heat treatments at 800 ℃, varying treatment times of 30 mins, 360 mins and 1,440 mins. The results confirm the formation of o phases and secondary austenite (γ2). For the analysis of the influence of o and γ2 phases, metallographic analysis were conducted through optical microscopy, potentiokinetic reactivation electrochemical techniques and potentiodynamic polarization in NaCI 3.5% solution. Microstructural analysis has shown a formation of γ2 and o phase in heat treatment, due to diffusion of chromium and molybdenum from δ phase to y phase, precipitating on δ/γ and δ/δ interfaces. The DL-EPR (Double loop electrochemical potentiokinetic reactivation) results have shown an increase of the DOS (degree of sensitization) for long periods of time on heat treatment. The results of potentiodynamic polarization showed a reduction of the corrosion and pitting potentials, followed by an increase of the current density when the UNS S31830 steel is heat treated during long periods of time.展开更多
Finite element analysis has been carried out to understand the effect of various processing routes and condition on the microscale deformation behavior of Al–4.5 Cu–2 Mg alloy. The alloy has been developed through f...Finite element analysis has been carried out to understand the effect of various processing routes and condition on the microscale deformation behavior of Al–4.5 Cu–2 Mg alloy. The alloy has been developed through four different routes and condition, i.e. conventional gravity casting with and without refiner, rheocasting and SIMA process. The optical microstructures of the alloy have been used to develop representative volume elements(RVEs). Two different boundary conditions have been employed to simulate the deformation behavior of the alloy under uniaxial loading. Finally, the simulated stress-strain behavior of the alloy is compared with the experimental result. It is found that the microstructural morphology has a significant impact on stress and strain distribution and load carrying capacity. The eutectic phase always carries a higher load than the α(Al) phase. The globular α(Al) grains with thinner and uniformly distributed eutectic network provide a better stress and strain distribution. Owing to this, SIMA processed alloy has better stress and strain distribution than other processes. Finally, the simulated yield strength of the alloy is verified by experiment and they have great agreement.展开更多
Ti/Cu/Ti laminated composites were fabricated by corrugated rolling(CR) and flat rolling(FR) method.Microstructure and mechanical properties of CR and FR laminated composites were investigated by scanning electron mic...Ti/Cu/Ti laminated composites were fabricated by corrugated rolling(CR) and flat rolling(FR) method.Microstructure and mechanical properties of CR and FR laminated composites were investigated by scanning electron microscopy, numerical simulation methods, peel and tensile examinations. The effect of CR and FR was comparatively analyzed. The results showed that the CR and FR laminated composites exhibited different effective plastic strain distributions of the Ti layer and Cu layer at the interface. The recrystallization texture, prismatic texture and pyramidal texture were developed in the Ti layer by CR, while the R-Goss texture and shear texture were developed in the Cu layer by CR. The typical deformation texture components were developed in the Ti layer and Cu layer of FR laminated composites. The CR laminated composites had higher bond strength, tensile strength and ductility.展开更多
The objective of this study is to presume cesium corrosion process and its dominant factors in SUS316 steel, a fuel cladding material for fast breeder reactor application, based on both experimental results of cesium ...The objective of this study is to presume cesium corrosion process and its dominant factors in SUS316 steel, a fuel cladding material for fast breeder reactor application, based on both experimental results of cesium corrosion out-pile test and thermodynamic consideration. The cesium corrosion test was performed in simulated environment of high burn-up fuel pin. And main corrosion products in the specimen after the corrosion test were specified by TEM (transition electron microscopy) and SEM (scanning electron microscopy) in order to formulate a hypothesis of the cesium corrosion process. At the end of this study, it was found that the dominant factors of the corrosion process are the amount of cesium on the surface of the specimen, chromium content in the alloy, the supply rate of oxygen and temperature.展开更多
文摘Polyether ether ketone(PEEK)has good mechanical properties.However,its high viscosity when molten limits its use because it is hard to process.PEEK nanocomposites containing both carbon nanotubes(CNTs)and polyether imide(PEI)were pre-pared by a direct wet powder blending method using a vertical injection molding machine.The addition of an optimum amount of PEI lowered the viscosity of the molten PEEK by approximately 50%while producing an increase in the toughness of the nanocom-posites,whose strain to failure increased by 129%,and fracture energy increased by 97%.The uniformly dispersed CNT/PEI powder reduced the processing difficulty of PEEK nanocomposites without affecting the thermal resistance.This improvement of the strength and viscosity of PEEK facilitate its use in the preparation of thermoplastic composites.
基金Project (10964004) supported by the National Natural Science Foundation of ChinaProject (20070731001) supported by Research Fund for the Doctoral Program of ChinaProject (096RJZA104) supported by the Natural Science Foundation of Gansu Province,China
文摘The influence of supercooled melt forced lamina flow on microsegregation was investigated. The concentration distribution at solid-liquid boundary of binary alloy Ni-Cu was simulated using phase field model coupled with flow field. The microsegregation, concentration maximum value, boundary thickness of concentration near upstream dendrite and normal to flow dendrite, and downstream dendrite were studied quantitatively in the case of forced lamia flow. The simulation results show that solute field and flow field interact complexly. Compared with melt without flow, in front of upstream dendrite tip, the concentration boundary thickness is the lowest and the concentration maximum value is the smallest for melt with flow. However, in front of downstream dendrite tip, the results are just the opposite. The zone of poor Cu in upstream dendrite where is the most severely microsegregation and shrinkage cavity is wider and the concentration is lower for melt with flow than that without flow.
基金Projects (2005CB724105,2011CB706801) supported by the National Basic Research Program of ChinaProjects (10477010,51171089) supported by the National Natural Science Foundation of ChinaProjects (2009ZX04006-041-04,2011ZX04014-052) supported by the Important National Science&Technology Specific,China
文摘The effects of cooling rate on the solidification parameters and microstructure of Al-7Si-0.3Mg-0.15 Fe alloy during solidification process were studied.To obtain different cooling rates,the step casting with five different thicknesses was used and the cooling rates and solidification parameters were determined by computer-aided thermal analysis method.The results show that at higher cooling rates,the primary α(Al) dendrite nucleation temperature,eutectic reaction temperature and solidus temperature shift to lower temperatures.Besides,with increasing cooling rate from 0.19 ℃/s up to 6.25 ℃/s,the secondary dendritic arm spacing decreases from 68 μm to 20 μm,and the primary dendritic volume fraction declines by approximately 5%.In addition,it reduces the length of Fe-bearing phase from 28 μm to 18 μm with a better uniform distribution.It is also found that high cooling rates make for modifying eutectic silicon into fibrous branched morphology,and decreasing block or lamella shape eutectic silicon.
基金Project (2011DAE22B01) supported by the Key Technologies Program of China during the 12th Fire-Year Plan Period
文摘Morphology and crystal structure of β precipitate phase in Mg-7Gd-5Y-1Nd-0.5Zr (mass fraction, %) alloy were characterized by optical microscopy, scanning electron microscopy and transmission electron microscopy. Compositions were determined for β phase using thin foil energy dispersive spectroscopy. Precipitation at 400 ℃ involves formation of platelet and block-shaped β phase. The orientation relationship is and between β precipitate phase and α-Mg matrix with habit planes parallel to , and a composition of Mg5(Y0.4Gd0.4Nd0.2) is suggested for the β phase in Mg-7Gd-5Y-1Nd-0.5Zr alloy.
基金Project(2019zzts678)supported by the Fundamental Research Funds for the Central Universities,China。
文摘In this study,different influence mechanisms associated with temperatures and pH values were investigated through cemented paste backfill(CPB)systems.CPB samples were prepared with temperatures ranging from 10 to 50℃ in 10℃ increments and pH values of 3,7,and 13.Then,the CPB mixture were subjected to rheological tests,thermogravimetric analysis(TG),derivative thermogravimetry analysis(DTG),Fourier-transform infrared spectroscopy(FT-IR),and scanning electron microscopy(SEM).Results demonstrated that the temperatures had significant effects on the rheological properties of CPB,whereas the effects of pH values were relatively unapparent.Higher temperatures(over 20℃)were prone to bring higher shear stress,yield stress,and apparent viscosity with the same pH value condition.However,an overly high temperature(50℃)cannot raise the apparent viscosity.Non-neutral conditions,for pH values of 3 and 13,could strengthen the shear stress and apparent viscosity at the same temperature.Two different yield stress curves could be discovered by uprising pH values,which also led to apparent viscosity of two various curves under the same temperatures(under 50℃).Microscopically,rheological properties of CPB were affected by temperatures and pH values which enhanced or reduced the cement hydration procedures,rates,products and space structures.
基金Supported by the National Natural Science Foundation of China(Nos. 40906069,40776094)Shangdong 908 Project (No. SD-908-02-08)+1 种基金the Haiwaijiechuxuezhe-Fund of Chinese Academy of Sciences (No.2006-1-15)K. C. WONG Education Foundation
文摘Multicellular magnetotactic prokaryotes (MMPs) are a group of aggregates composed of 7-45 gram-negative cells synthesizing intracellular magnetic crystals. Although they are thought to be globally distributed, MMPs have been observed only in marine environments in America and Europe. Most MMPs share a rosette-like morphology and biomineralize iron sulfide crystals. In the present study, abundant MMPs were observed, with a density of 26 ind./cm^3, in the sediments of a coastal lagoon, Lake Yuehu, in the Yellow Sea. Optical microscopy showed that all of them were rosette shaped with a diameter of 5.5±0.8 μm. Transmission electron microscopy revealed that these MMPs were composed of 10- 16 ovoid cells and flagellated peritrichously. High-resolution transmission electron microscopy and energy dispersive X-ray analysis indicated that they biomineralized bullet-shaped magnetite crystals in highly organized parallel chains within which the magnetosomes were oriented in the same direction. This is the first report of MMPs from Asia and demonstrates the ubiquitous distribution of MMPs.
基金Project(2008ZA11) supported by State Key Laboratory of Subtropical Building Science in South China University of Technology, ChinaProject(20080430815) supported by China Postdoctoral Science Foundation
文摘A series of researches were carried out for the soil samples in the Pearl River Delta under the action of consolidation loads,such as the quantitative analyses of the pore scale,shape and size distributions of micro-structure units,with an environmental scanning electron microscope (ESEM),a mercury intrusion analyzer and a mineral diffractometer. The experimental results show that the consolidation pressures remarkably change the pore sizes and distribution characteristics of the silt,thus changing its compressibility and permeability. This can be proved by the fact that,in the earlier stage with a consolidation pressure of p<200 kPa,the pore sizes are greater and the compressibility and permeability coefficients are larger. However,they rapidly decrease with the increase in consolidation pressure. And in the later stage with a consolidation pressure of p>200 kPa,the pore sizes are smaller and the compressibility and permeability coefficients are less. Therefore,the empirical formulas of compression coefficient and permeability coefficient vs consolidation load and average pore diameter are deduced.
基金Project(2016GK1004)supported by the Science and Technology Major Project of Hunan Province,China
文摘The effect of an ultrasonic field on the microstructure and mechanical properties of 7085 aluminum alloy during solidification was investigated by optical microscopy, Vickers hardness test, tensile test, scanning electron microscopy (SEM) with energy dispersive X-ray spectrometry, and electron probe micro-analysis (EPMA). The results showed that the grains of aluminum alloy were significantly refined and secondary phases were dispersed and distributed uniformly at the grain boundaries, due to ultrasonic treatment (UST). By EPMA, it was observed that the distribution of the main elements A1, Zn, Mg and Cu was more homogeneous in alloys with UST, than in alloys without UST. The mechanical properties of the aluminum alloy also significantly improved. As demonstrated by the SEM fractography of the fractured faces of several castings, fracture of the unrefined specimens occurred in a brittle manner, whereas the cracks of the refined specimens showed quasi-cleavage fracture.
基金Project(CXZZBS2019126)supported by the Innovative Support Program for Doctoral Students in Hebei Province,ChinaProject(QN2019078)supported by the Science and Technology Research Project of Colleges and University in Hebei Province,ChinaProject(51774137)supported by the National Natural Science Foundation of China。
文摘In view of the mechanics characteristic of cemented tailings backfill(CTB)at early age,the separation Hopkinson pressure bar test device was used to explore the effects of curing age and impact energy.A total of 48 CTB samples with diameter of 50 mm and length of 25 mm were prepared with curing ages of 3,5,7 and 9 d.Impact tests under different impact energy(10,20,30 and 40 J)were carried out.The microstructure of CTB at different ages was analyzed by scanning electron microscopy(SEM).The results show that,the curing age mainly affects the mechanical properties and internal structure of early-age CTB.With increasing curing age,the mechanical properties of early-age CTB change from viscoelasticity to brittleness.The impact energy mainly affects the response of dynamic peak compressive strength to strain rate.Under low strain rate,the structure of CTB is broken,but still has bearing capacity,affecting the formation of later strength.It is concluded that the structural loses completely under the action of high strain rate.Therefore,the control of impact energy and the protection of curing age should be fully considered in actual production process.
基金Project(51278403)supported by the National Natural Science Foundation of China
文摘The damage process of concrete exposed to sodium sulfate attack and drying-wetting cycles was investigated. The water to binder(W/B) ratio and the concentration of sulfate solution were taken as variable parameters. Through the experiment, visual change, relative dynamic modulus of elasticity(RDME) and the surface damage layer thickness of concrete were measured.Furthermore, SEM and thermal analysis were used to investigate the changing of microstructure and corrosion products of concrete.The test results show that the ultrasonic velocity is related to the damage layer of concrete. It approves that an increase in damage layer thickness reduces the compactness and the ultrasonic velocity. The deterioration degree of concrete could be estimated effectively by measuring the surface damage layer and the RDME of concrete. It is also found that the content of gypsum in concrete is less than that of ettringite in test, and some gypsum is checked only after a certain corrosion extent. When the concrete is with high W/B ratio or exposed to high concentration of sulfate solution, the content of ettringite first increases and then decreases with corrosion time. However, the content of gypsum increases at a steady rate. The content of corrosion products does not correspond well with the observations of RDME change, and extensive amount of corrosion products can be formed before obvious damage occurs.
基金Projects(51674188,51874229,51504182)supported by the National Natural Science Foundation of ChinaProject(2018KJXX-083)supported by Shaanxi Innovative Talents Cultivate Program-New-star Plan of Science and Technology,China
文摘The mechanical properties of cemented paste backfill(CPB) depend heavily on its pore structural characteristics and micro-structural changes. In order to explore the variation mechanisms of macro-mechanical characteristics and micro-structure of CPB. CPB specimens with different mass concentrations prepared from the full tailings of Xianglushan Tungsten Ore were micro-tests. Moreover, acquired pore digital images were processed by using the pores(particles) and cracks analysis system(PCAS), and a sensitivity analysis was performed. The results show that as the mass concentration of CPB increases from 70% to 78%, the porosity, the average pore area and the number of pores drop overall, leading to a decline in the pores opening degree and enhancing the mechanical characteristics. As the mass concentration of CPB increases, the trend of fractal dimension, probability entropy and roundness is reduced, constant and increased, which can result in an enhancement of the uniformity, an unchanged directionality and more round pores. According to the definition of sensitivity, the sensitivities of various micro-parameters were calculated and can be ranked as porosity > average pore area > number of pores > roundness > fractal dimension > probability entropy.
基金funded by the Thai Research Fund (Contract No.MRG5280215)the Royal Golden Jubilee Ph.D. Program (Grant No.PHD/0134/2551)
文摘Semi-solid metal processing is being developed in die casting applications to give several cost benefits. To efficiently apply this emerging technology, it is important to understand the evolution of microstructure in semi-solid slurries for the control of the theological behavior in semi-solid state. An experimental apparatus was developed which can capture the grain structure at different times at early stages to understand how the semi-solid structure evolves. In this technique, semi-solid slurry was produced by injecting fine gas bubbles into the melt through a graphite diffuser during solidification. Then, a copper quenching mold was used to draw some semi-solid slurry into a thin channel. The semi-solid slurry was then rapidly frozen in the channel giving the microstructure of the slurry at the desired time. Samples of semi-solid 356 aluminum alloy were taken at different gas injection times of 1, 5, 10, 15, 20, 30, 35, 40, and 45 s. Analysis of the microstructure suggests that the fragmentation by remelting mechanism should be responsible for the formation of globular structure in this rheocasting process.
文摘Although the first microscopic observations on soils date already from the beginning of the twentieth century, the publication of Kubiena's book "Micropedology" in 1937 is considered as the beginning of this new scientific discipline. This first system for micromorphological descriptions of soils is considered as morphoanalytical, analysing the fabric according to pure morphological criteria. In a second period Kuniena used a morphogenetic approach, directly relating the global observed fabric to genetic soil horizons. This system, mainly limited to European soils, was in general use till the early nineteen-seventies. End of the nineteen-fifties non- genetic soil classification systems were developed (e.g. USDA). This trend prompted R. Brewer to publish in 1964 a new morphoanalytical system for fabric analysis, used till the end of last century. Because of some inconsistencies in this approach, a working group of the ISSS published in 1985 a new set of morphoanalytical concepts and associated terminology (Bullock et al.), in 2003 adapted and extended by Stoops. Several morphosynthetic systems, expressing a complete soil microfabric in a single (compound) term have been proposed, but none was really successful. In 1967 Kubiena introduced the term "micromorphometry" to name a new branch of micromorphology quantifying the soil fabric, mainly evaluating changes in porosity and structure resulting from soil management. The necessity of dearly defined concepts and terms for fabric analysis of soils and regoliths, even as a need for standardisation of quantitative methods, are discussed in the conclusions.
基金Project(51474161)supported by the National Natural Science Foundation of China
文摘The chemical compositions,mineralogical characteristics,as well as dissemination of iron-and phosphorus-based minerals were studied for the E’xi oolitic hematite from western Hubei Province in China by using chemical analysis,optical microscope,electron probe micro-analyzer(EPMA)and energy dispersive spectroscopy(EDS).It is found that this kind of oolitic hematite ore contains 47.71%TFe,10.96%SiO_2,as well as 0.874%P,with hematite as the dominant Fe-bearing minerals,and quartz,chamosite,illite and cellophane as main gangue minerals.The microscope examination showed that the ore has an oolitic structure,with some ooids principally formed by a series of concentric layers of hematite collophanite around nucleus that is hematite in the association with collophanite.Based on the EPMA and EDS analysis,it can be known that some ooids are primarily composed of hematite and collophanite.The separation can be achieved through fine grinding for those collophanite laminae with a higher P content.However,the dissemination of two minerals at the interface will result in the difficulty in effective separation.Besides,some ooids are made of chamosite with some nucleus formed of quartz,which is principally finely disseminated with hematite.In view of the close association and dissemination of iron-and phosphorus-based minerals in the ooids,it is found that the process of stage-grindings and stage-separations can be adopted to effectively increase the iron recovery and decrease the P content in the concentrate to some extent.
基金Project(2017FA027)supported by the Key Project of Science and Technology of Yunnan Province,China。
文摘The finite element model is established according to the experimental results,and then the experimental results are verified by simulation calculation.In terms of the combination of finite element analysis and experiment,the effect of particle size of CuO and SnO_(2) on the stress,strain and microstructure of AgCuOSnO_(2) composite during hot extrusion was studied.The results illustrate that with the decrease of particle size,the dispersion of the second phase increases gradually,while the possibility of“tail shrinkage”of the billet decreases continuously;cubic CuO will evolve to fibrosis,and the degree of fibrosis will increase with the decrease of the particle size and ring clusters.Specifically,the degree of fibrosis at the middle end of the billet is higher than that at the front end,the degree of fibrosis at the front end is higher than that at the back end,and the degree of fibrosis on the surface is higher than that in the core;part of CuO fibers will bend,and the degree of buckling strength is positively correlated with the size of particles and their annular clusters.Additionally,there is fiber CuO in the front and back end of the billet that are inconsistent with the extrusion direction,and the degree of difference was negatively correlated with the particle size.
文摘The aim of this work is evaluate the intergranular corrosion on UNS S31803 steel, with heat treatments at 800 ℃, varying treatment times of 30 mins, 360 mins and 1,440 mins. The results confirm the formation of o phases and secondary austenite (γ2). For the analysis of the influence of o and γ2 phases, metallographic analysis were conducted through optical microscopy, potentiokinetic reactivation electrochemical techniques and potentiodynamic polarization in NaCI 3.5% solution. Microstructural analysis has shown a formation of γ2 and o phase in heat treatment, due to diffusion of chromium and molybdenum from δ phase to y phase, precipitating on δ/γ and δ/δ interfaces. The DL-EPR (Double loop electrochemical potentiokinetic reactivation) results have shown an increase of the DOS (degree of sensitization) for long periods of time on heat treatment. The results of potentiodynamic polarization showed a reduction of the corrosion and pitting potentials, followed by an increase of the current density when the UNS S31830 steel is heat treated during long periods of time.
文摘Finite element analysis has been carried out to understand the effect of various processing routes and condition on the microscale deformation behavior of Al–4.5 Cu–2 Mg alloy. The alloy has been developed through four different routes and condition, i.e. conventional gravity casting with and without refiner, rheocasting and SIMA process. The optical microstructures of the alloy have been used to develop representative volume elements(RVEs). Two different boundary conditions have been employed to simulate the deformation behavior of the alloy under uniaxial loading. Finally, the simulated stress-strain behavior of the alloy is compared with the experimental result. It is found that the microstructural morphology has a significant impact on stress and strain distribution and load carrying capacity. The eutectic phase always carries a higher load than the α(Al) phase. The globular α(Al) grains with thinner and uniformly distributed eutectic network provide a better stress and strain distribution. Owing to this, SIMA processed alloy has better stress and strain distribution than other processes. Finally, the simulated yield strength of the alloy is verified by experiment and they have great agreement.
基金financially supported by the National Key R&D Program of China (No.2018YFA0707300)the Natural Science Foundation of Shanxi Province,China (No.201801D221131)+2 种基金the National Natural Science Foundation of China (Nos.51905372,51904206,51805359,52075359)Shanxi Province Science and Technology Major Project,China (No.20181102011)China Postdoctoral Science Foundation (No.2020M670705)。
文摘Ti/Cu/Ti laminated composites were fabricated by corrugated rolling(CR) and flat rolling(FR) method.Microstructure and mechanical properties of CR and FR laminated composites were investigated by scanning electron microscopy, numerical simulation methods, peel and tensile examinations. The effect of CR and FR was comparatively analyzed. The results showed that the CR and FR laminated composites exhibited different effective plastic strain distributions of the Ti layer and Cu layer at the interface. The recrystallization texture, prismatic texture and pyramidal texture were developed in the Ti layer by CR, while the R-Goss texture and shear texture were developed in the Cu layer by CR. The typical deformation texture components were developed in the Ti layer and Cu layer of FR laminated composites. The CR laminated composites had higher bond strength, tensile strength and ductility.
文摘The objective of this study is to presume cesium corrosion process and its dominant factors in SUS316 steel, a fuel cladding material for fast breeder reactor application, based on both experimental results of cesium corrosion out-pile test and thermodynamic consideration. The cesium corrosion test was performed in simulated environment of high burn-up fuel pin. And main corrosion products in the specimen after the corrosion test were specified by TEM (transition electron microscopy) and SEM (scanning electron microscopy) in order to formulate a hypothesis of the cesium corrosion process. At the end of this study, it was found that the dominant factors of the corrosion process are the amount of cesium on the surface of the specimen, chromium content in the alloy, the supply rate of oxygen and temperature.