In this paper, coordinated control of multiple robot manipulators holding a rigid object is discussed. In consideration of inaccuracy of the dynamic model of a multiple manipulator system, the error equations on obje...In this paper, coordinated control of multiple robot manipulators holding a rigid object is discussed. In consideration of inaccuracy of the dynamic model of a multiple manipulator system, the error equations on object position and internal force are derived. Then a hybrid position/force coordinated learning control scheme is presented and its convergence is proved. The scheme can improve the system performance by modifying the control input of the system after each iterative learning. Simulation results of two planar robot manipulators holding an object show the effectiveness of this control scheme.展开更多
The control method of highly redundant robot manipulators is introduced. A decentralized autonomous control scheme is used to guide the movement of robot manipulators so that the work done by manipulators is minimized...The control method of highly redundant robot manipulators is introduced. A decentralized autonomous control scheme is used to guide the movement of robot manipulators so that the work done by manipulators is minimized. The method of computing pseudoinverse which needs too many complicated calculation can be avoided. Then the calculation and control of robots are simplified. At the same time system robustness/fault tolerance is achieved.展开更多
Because of its ease of implementation,a linear PID controller is generally used to control robotic manipulators.Linear controllers cannot effectively cope with uncertainties and variations in the parameters;therefore,...Because of its ease of implementation,a linear PID controller is generally used to control robotic manipulators.Linear controllers cannot effectively cope with uncertainties and variations in the parameters;therefore,nonlinear controllers with robust performance which can cope with these are recommended.The sliding mode control(SMC)is a robust state feedback control method for nonlinear systems that,in addition having a simple design,efficiently overcomes uncertainties and disturbances in the system.It also has a very fast transient response that is desirable when controlling robotic manipulators.The most critical drawback to SMC is chattering in the control input signal.To solve this problem,in this study,SMC is used with a boundary layer(SMCBL)to eliminate the chattering and improve the performance of the system.The proposed SMCBL was compared with inverse dynamic control(IDC),a conventional nonlinear control method.The kinematic and dynamic equations of the IRB-120 robot manipulator were initially extracted completely and accurately,and then the control of the robot manipulator using SMC was evaluated.For validation,the proposed control method was implemented on a 6-DOF IRB-120 robot manipulator in the presence of uncertainties.The results were simulated,tested,and compared in the MATLAB/Simulink environment.To further validate our work,the results were tested and confirmed experimentally on an actual IRB-120 robot manipulator.展开更多
We present the development of a novel prosthetic hand based on the underactuated mechanism. The aim is focused on increasing its dexterity while keeping the same dimension and weight of a traditional prosthetic device...We present the development of a novel prosthetic hand based on the underactuated mechanism. The aim is focused on increasing its dexterity while keeping the same dimension and weight of a traditional prosthetic device. The hybrid step motor is used as the actuator, which enables the finger to keep enough high contact torque on the grasped object with less energy consumption provided by the holding torque. The grasping force of the finger is estimated from the base joint torque, and the adoption of impedance control has provided compliance in the grasping. Also a parallel observer is used to switch over between the impedance control and the torque holding mode. The experimental results show the effectiveness of the design and control strategy.展开更多
Presents a novel compliant motion control for a robot hand using the Cartesian impedance approach based on fingertip force measurements. The fingertip can accurately track desired motion in free space and appear as me...Presents a novel compliant motion control for a robot hand using the Cartesian impedance approach based on fingertip force measurements. The fingertip can accurately track desired motion in free space and appear as mechanical impedance in constrained space. In the position based impedance control strategy, any switching mode in contact transition phase is not needed. The impedance parameters can be adjusted in a certain range according to various tasks. In this paper, the analysis of the finger’s kinematics and dynamics is given. Experimental results have shown the effectiveness of this control strategy.展开更多
AIM： To summarize the performing essentials and analyze the characteristics of remote Zeus robot-assisted laparoscopic cholecystectomy. METHODS： Robot-assisted laparoscopic cholecystectomy was performed in 40 patien...AIM： To summarize the performing essentials and analyze the characteristics of remote Zeus robot-assisted laparoscopic cholecystectomy. METHODS： Robot-assisted laparoscopic cholecystectomy was performed in 40 patients between May 2004 and July 2005. The operating procedures and a variety of clinical parameters were recorded and analyzed. RESULTS： Forty laparoscopic cholecystectomy procedures were successfully completed with Zeus robotic system. And there were no post-operative complications. Total operating time, system setup time and performing time were 100.3±18.5 min, 27.7±8.8 min and 65.6±18.3 min, respectively. The blood loss and postoperative hospital stay were 30.6±10.2 mL and 2.8±0.8 d, respectively. Camera clearing times and time used for operative field adjustment were 1.1±1.0 min and 2.0±0.8 rain, respectively. The operative error was 7.5%. CONCLUSION： Robot-assisted laparoscopic cholecystectomy following the principles of laparoscopic operation has specific performing essentials. It preserves the benefits of minimally invasive surgery and offers enhanced ability of controlling operation field, precise and stable operative manipulations.展开更多
Nowadays many anthropomorphic robotic hands have been put forward. These hands emphasize different aspects according to their applications. HIT Anthropomorphic Robotic Hand (ARhand) is a simple, lightweight and dexter...Nowadays many anthropomorphic robotic hands have been put forward. These hands emphasize different aspects according to their applications. HIT Anthropomorphic Robotic Hand (ARhand) is a simple, lightweight and dexterous design per the requirements of anthropomorphic robots. Underactuated self-adaptive theory is adopted to decrease the number of motors and weight. The fingers of HIT ARhand with multi phalanges have the same size as those of an adult hand. Force control is realized with the position sensor, joint torque sensor and fingertip torque sensor. From the 3D model, the whole hand, with the low power consumption DSP control board integrated in it, will weigh only 500 g. It will be assembled on a BIT-Anthropomorphic Robot.展开更多
Based on the characteristics of integrated virtual prototype technology, the mechanical system sub-model, the hydraulic system sub-model and the control system sub-model of a forging manipula- tor system have been bui...Based on the characteristics of integrated virtual prototype technology, the mechanical system sub-model, the hydraulic system sub-model and the control system sub-model of a forging manipula- tor system have been built using a variety of software, and a forging manipulator mtrltidisciplinary co- simulation model has been also built using a method of simulation models interface. Then the simu- lation and experiment are finished, and the result of the experiment is in good agreement with the re- sult of the simulation. It shows that the co-simulation model established can simulate accurately pa- rameter changes in real time during the moving of the forging manipulator such as displacement, ve- locity and pressure flow, which is of important significance for the optimized design of the forging manipulator system to establish the models.展开更多
A novel control system is developed to improve the capabilities of robet hand performing tasks in a variety of environments. A joint impedance control strategy has been successfully implemented in the low level contro...A novel control system is developed to improve the capabilities of robet hand performing tasks in a variety of environments. A joint impedance control strategy has been successfully implemented in the low level control of a highly integrated robot hand. At flint, a real time controller with DSP＆FPGA-based multilevel control architecture is built. Then a current sensor of the single direct current （DC） link is used to measure and reconstruct the three phase currents, and a stable current signal is measured by optimizing sample instant. The experimental results of the joint impedance control show that the proposed method not only improves the effectiveness of contact environment performance, but also provides compliant interaction of robot hand with a person, which is very important for the development of friendly human robot of the next generation.展开更多
文摘In this paper, coordinated control of multiple robot manipulators holding a rigid object is discussed. In consideration of inaccuracy of the dynamic model of a multiple manipulator system, the error equations on object position and internal force are derived. Then a hybrid position/force coordinated learning control scheme is presented and its convergence is proved. The scheme can improve the system performance by modifying the control input of the system after each iterative learning. Simulation results of two planar robot manipulators holding an object show the effectiveness of this control scheme.
文摘The control method of highly redundant robot manipulators is introduced. A decentralized autonomous control scheme is used to guide the movement of robot manipulators so that the work done by manipulators is minimized. The method of computing pseudoinverse which needs too many complicated calculation can be avoided. Then the calculation and control of robots are simplified. At the same time system robustness/fault tolerance is achieved.
文摘Because of its ease of implementation,a linear PID controller is generally used to control robotic manipulators.Linear controllers cannot effectively cope with uncertainties and variations in the parameters;therefore,nonlinear controllers with robust performance which can cope with these are recommended.The sliding mode control(SMC)is a robust state feedback control method for nonlinear systems that,in addition having a simple design,efficiently overcomes uncertainties and disturbances in the system.It also has a very fast transient response that is desirable when controlling robotic manipulators.The most critical drawback to SMC is chattering in the control input signal.To solve this problem,in this study,SMC is used with a boundary layer(SMCBL)to eliminate the chattering and improve the performance of the system.The proposed SMCBL was compared with inverse dynamic control(IDC),a conventional nonlinear control method.The kinematic and dynamic equations of the IRB-120 robot manipulator were initially extracted completely and accurately,and then the control of the robot manipulator using SMC was evaluated.For validation,the proposed control method was implemented on a 6-DOF IRB-120 robot manipulator in the presence of uncertainties.The results were simulated,tested,and compared in the MATLAB/Simulink environment.To further validate our work,the results were tested and confirmed experimentally on an actual IRB-120 robot manipulator.
基金Supported by t he National Natural Science Foundation of China （ No. 50435040） and the High Technology Research and Development Programme of China（ No. 2003AA420010）.
文摘We present the development of a novel prosthetic hand based on the underactuated mechanism. The aim is focused on increasing its dexterity while keeping the same dimension and weight of a traditional prosthetic device. The hybrid step motor is used as the actuator, which enables the finger to keep enough high contact torque on the grasped object with less energy consumption provided by the holding torque. The grasping force of the finger is estimated from the base joint torque, and the adoption of impedance control has provided compliance in the grasping. Also a parallel observer is used to switch over between the impedance control and the torque holding mode. The experimental results show the effectiveness of the design and control strategy.
文摘Presents a novel compliant motion control for a robot hand using the Cartesian impedance approach based on fingertip force measurements. The fingertip can accurately track desired motion in free space and appear as mechanical impedance in constrained space. In the position based impedance control strategy, any switching mode in contact transition phase is not needed. The impedance parameters can be adjusted in a certain range according to various tasks. In this paper, the analysis of the finger’s kinematics and dynamics is given. Experimental results have shown the effectiveness of this control strategy.
基金Supported by the Jieping Wu Medical Foundation, No.2003-49-A
文摘AIM： To summarize the performing essentials and analyze the characteristics of remote Zeus robot-assisted laparoscopic cholecystectomy. METHODS： Robot-assisted laparoscopic cholecystectomy was performed in 40 patients between May 2004 and July 2005. The operating procedures and a variety of clinical parameters were recorded and analyzed. RESULTS： Forty laparoscopic cholecystectomy procedures were successfully completed with Zeus robotic system. And there were no post-operative complications. Total operating time, system setup time and performing time were 100.3±18.5 min, 27.7±8.8 min and 65.6±18.3 min, respectively. The blood loss and postoperative hospital stay were 30.6±10.2 mL and 2.8±0.8 d, respectively. Camera clearing times and time used for operative field adjustment were 1.1±1.0 min and 2.0±0.8 rain, respectively. The operative error was 7.5%. CONCLUSION： Robot-assisted laparoscopic cholecystectomy following the principles of laparoscopic operation has specific performing essentials. It preserves the benefits of minimally invasive surgery and offers enhanced ability of controlling operation field, precise and stable operative manipulations.
文摘Nowadays many anthropomorphic robotic hands have been put forward. These hands emphasize different aspects according to their applications. HIT Anthropomorphic Robotic Hand (ARhand) is a simple, lightweight and dexterous design per the requirements of anthropomorphic robots. Underactuated self-adaptive theory is adopted to decrease the number of motors and weight. The fingers of HIT ARhand with multi phalanges have the same size as those of an adult hand. Force control is realized with the position sensor, joint torque sensor and fingertip torque sensor. From the 3D model, the whole hand, with the low power consumption DSP control board integrated in it, will weigh only 500 g. It will be assembled on a BIT-Anthropomorphic Robot.
基金Supported by the National Natural Science Foundation of China(No.51575471)Collaborative Innovation Program Topics of Heavy Machinery of Yanshan University(2011 Program,No.ZX01-20140400-01)
文摘Based on the characteristics of integrated virtual prototype technology, the mechanical system sub-model, the hydraulic system sub-model and the control system sub-model of a forging manipula- tor system have been built using a variety of software, and a forging manipulator mtrltidisciplinary co- simulation model has been also built using a method of simulation models interface. Then the simu- lation and experiment are finished, and the result of the experiment is in good agreement with the re- sult of the simulation. It shows that the co-simulation model established can simulate accurately pa- rameter changes in real time during the moving of the forging manipulator such as displacement, ve- locity and pressure flow, which is of important significance for the optimized design of the forging manipulator system to establish the models.
文摘A novel control system is developed to improve the capabilities of robet hand performing tasks in a variety of environments. A joint impedance control strategy has been successfully implemented in the low level control of a highly integrated robot hand. At flint, a real time controller with DSP＆FPGA-based multilevel control architecture is built. Then a current sensor of the single direct current （DC） link is used to measure and reconstruct the three phase currents, and a stable current signal is measured by optimizing sample instant. The experimental results of the joint impedance control show that the proposed method not only improves the effectiveness of contact environment performance, but also provides compliant interaction of robot hand with a person, which is very important for the development of friendly human robot of the next generation.
