略论张岱年先生对“气学”的梳理和转化

“气学”始于张载,王廷相、王夫之、戴震等以继之,以“问题”为导向的“气学”与“心学”“理学”较之,并没有明显的、自觉性的传承脉络,致使近代一些学者仅将宋明道学分为两派,即“程朱理学”和“陆王心学”,张岱年先生在其兄张申府先生学术的影响下,明确将宋明哲学划分为“理”“心”“气”三系。他通过梳理古代唯物主义,将“气学”分为“自然论”“唯有论”“唯气论”三大主要形态,并肯定了“气学”的重要地位;以宋代为界,张载是把“气论”向“气学”转折的重要人物,完善了“气学”的传承脉络;张岱年以传统“气学”为基,将唯物论哲学与传统“气学”相结合,为其赋予现代含义,力图开辟中国传统哲学现代转化的另一条路向。

浅析张载“气学”的唯物主义思想

张载创立的以"气学"论为核心,以"文质相得、体用不离"为特点的唯物辩证主义哲学体系,开拓了宋儒经学哲学的新途径,以"独立不惧,精一自信"的理论勇气和学术气魄,为宋明理学奠定了深厚的基础。构成了中华民族理论发展长河中一个不可缺少的必然环节。此外,张载的哲学诸多地方表现出的"以躬行礼教为本"的"实学"作风,把他的宇宙论和理学、心学注重精神境界的人生结合起来,具有现实的指导意义。

A Dendroclimatic Study of Relic Picea meyeri in Inner Mongolian Steppe

Dendroclimatic methods were used to investigate the fundamental relationships between the temperature variables and the growth of climatically relic Picea meyeri Rehd. et Wils. on sandy land of Inner Mongolian grasslands in the Xilin River Basin. The annual mean temperature and accumulated temperature (above 5 ℃, 10 ℃) respectively showed no significant correlation with the spruce growth relative to summer mean temperature, which displayed strong coherence with tree growth ( P <0.01). The mean temperature in May showed significantly negative correlation with spruce growth ( P <0.05). Furthermore, it was revealed that the negative influence of May temperature was due to monthly mean maximum temperature ( T max ) ( P <0.01) other than monthly mean minimum temperature ( T min ) values ( P <0.1), which indicated that the use of T min and T max separately can allow much more insights on the temperate influence. In addition, extreme maximum temperature in May and June might impose the most detrimental influence on tree growth in semi_arid Inner Mongolian grassland. The analysis of the recorded meteorological data demonstrated that the increases in temperature were synchronous with slight decreases in precipitation in the growing season, which suggested that P. meyeri may reduce growth due to temperature_induced drought. On the other hand, the analysis for decadal periods explored that trees appeared to reduce the sensitivity to the warming, and consequently increased sensitivity to rainfall. This may serve as a baseline for more accurate predictions of the potential impacts of altered climate regimes on tree growth.

Age Differences in Behavioral Responses of Male Giant Pandas to Chemosensory Stimulation

Chemical communication plays an important role in survival and reproductive success in mammalian species. In the present study, we examined the ontogenetic pattern of behavioral responses of male giant pandas （Ailuropoda melanoleuca ） to urine odors of conspecific individuals. Our data showed that exposure to the urine of adult females induced a significant increase in sniffing and environmental sniffing/licking behaviors, but a decrease in biting behavior, in males. Males of different ages displayed specific behaviors to female urine odors. Adult males spent more time licking than juvenile and sub-adult males. Further, sub-adult and adult males displayed high levels of environmental sniffing/licking, which was absent in the juvenile males. Juvenile males displayed scent rubbing behavior significantly more frequently than sub-adult and adult males, and also spent more time showing biting behavior than sub-adult males. Finally, juvenile and sub-aduh males showed no difference in response to female and male urine odors. Together, these data suggest that chemosensory cues from conspecific urines induce age-specific responses in male giant pandas.

Removal of phosphorus from metallurgical grade silicon by Ar-H_2O gas mixtures

The removal of phosphorus in metallurgical grade silicon （MG-Si） by water vapor carried with high purity argon was examined. The effect of the nozzle types, refining time, refining temperature, refining gas temperature and refining gas flow rate on the phosphorus removed was investigated by the self-designed gas blowing device. The optimal refining conditions are nozzle type of holes at bottom and side, refining time of 3 h, refining temperature of 1793 K, refining gas temperature of 373 K, refining gas flow rate of 2 L/min. Under these optimal conditions, the phosphorus content in MG-Si is reduced from 94×10^-6 initially to 11×10-6 （mass fraction）, which indicates that gas blowing refining is very effective to remove phosphorus in MG-Si.

Preparation and mechanical properties of carbon/carbon composites with high textured pyrolytic carbon matrix

Short carbon fiber felts with an initial porosity of 89.5% were deposited by isobaric, isothermal chemical vapor infiltration using natural gas as carbon source. The bulk density of the deposited carbon/carbon （C/C） composites was 1.89 g/cm3 after depositing for 150 h. The microstructure and mechanical properties of the C/C composites were studied by polarized light microscopy, X-ray diffraction, scanning electron microscopy and three-point bending test. The results reveal that high textured pyrolytic carbon is deposited as the matrix of the composites, whose crystalline thickness and graphitization degree highly increase after heat treatment. A distinct decrease of the flexural strength and modulus accompanied by the increase of the toughness of the C/C composites is found to be correlated with the structural changes in the composites during the heat treatment process.

Preparation of ultrafine rhenium powders by CVD hydrogen reduction of volatile rhenium oxides

A novel CVD process for the preparation of ultrafine rhenium powders was investigated using ammonium perrhenate as starting materials. In the process, volatile rhenium oxides, such as ReO4 and Re2O7, were vaporized under a controlled oxidizing atmosphere via the pyrolysis of ammonium perrhenate, and carried into reduction zone by carrier gas, and there reduced into rhenium powders by hydrogen gas. Thermodynamic calculations indicated that Re207 could be prevented from further decomposition through controlling the oxygen partial pressure higher than 10 1.248 Pa in the pyrolysis of ammonium perrhenate. This result was further validated via DSC-TGA analysis of ammonium perrhenate. The typical rhenium powders prepared by the CVD method proposed show irregular polyhedron morphology with particle size in the range of 100-800 nm and a Ds0 of 308 nm. The specific surface area and oxygen content were measured to be 4.37 m^2/g and 0.45%, respectively.

Applications of seismic techniques to gas hydrates prediction

Based on the sensitivity of geophysical response to gas hydrates contained in sediments, we studied the prediction of gas hydrates with seismic techniques, including seismic attributes analysis, AVO, inverted velocity field construction for dipping formations, and pseudo-well constrained impedance inversion. We used an optimal integration of geophysical techniques results in a set of reliable and effective workflows to predict gas hydrates. The results show that the integrated analysis of the combination of reflectivity amplitude, instantaneous phase, interval velocity, relative impedance, absolute impedance, and AVO intercept is a valid combination of techniques for identifying the BSR （Bottom Simulated Reflector） from the lower boundary of the gas hydrates. Integration of seismic sections, relative and absolute impedance sections, and interval velocity sections can improve the validity of gas hydrates determination. The combination of instantaneous frequency, energy half attenuation time, interval velocity, AVO intercept, AVO product, and AVO fluid factor accurately locates the escaped gas beneath the BSR. With these conclusions, the combined techniques have been used to successfully predict the gas hydrates in the Dongsha Sea area.

Enhancement of nucleation of diamond films deposited on copper substrate by nickel modification layer

A Ni layer with a thickness of about 100 nm was sputtered on Cu substrates,followed by an ultrasonic seeding with nanodiamond suspension.High-quality diamond film with its crystalline grains close to thermal equilibrium shape was deposited on Cu substrates by hot-filament chemical vapor deposition（HF-CVD）,and the sp2 carbon content was less than 5.56%.The nucleation and growth of diamond film were investigated by micro-Raman spectroscopy,scanning electron microscopy,and X-ray diffraction.The results show that the nucleation density of diamond on the Ni-modified Cu substrates is 10 times higher than that on blank Cu substrates.The enhancement mechanism of the nucleation kinetics by Ni modification layer results from two effects：namely,the nanometer rough Ni-modified surface shows an improved absorption of nanodiamond particles that act as starting points for the diamond nucleation during HF-CVD process;the strong catalytic effect of the Ni-modified surface causes the formation of graphite layer that acts as an intermediate to facilitate diamond nucleation quickly.

Growth behavior of CVD diamond in microchannels of Cu template

Deposition of diamond inside the trenches or microchannels by chemical vapor deposition （CVD） is limited by the diffusion efficiency of important radical species for diamond growth （H, CH3） and the pore depth of the substrate template. By ultrasonic seeding with nanodiamond suspension, three-dimensional （3D） penetration structure diamond was successfully deposited in cylindrical microchannels of Cu template by hot-filament chemical vapor deposition. Micro-Raman spectroscopy and scanning electron microscopy （SEM） were used to characterize diamond film and the effects of microchannel depth on the morphology, grain size and growth rate of diamond film were comprehensively investigated. The results show that diamond quality and growth rate sharply decrease with the increase of the depth of cylindrical microchannel. Individual diamond grain develops gradually from faceted crystals into micrometer cluster, and finally to ballas-type nanocrystalline one. In order to modify the rapid decrease of diamond quality and growth rate, a new hot filament apparatus with a forced gas flow through Cu microchannels was designed. Furthermore, the growth of diamond film by new apparatus was compared with that without a forced gas flow, and the enhancement mechanism was discussed.

Characterization of SiC nanowires prepared on C/C composite without catalyst by CVD

SiC nanowires were prepared on C/C composite surface without catalyst by chemical vapor deposition（CVD） using CH3 SiCl3 as precursor.SEM images of the CVD-product reveal that some long nanowires have grown to tens of micrometers with some gathered as a ball.Some short nanowires agglomerate like chestnut shell with many thorns accompanied by some deposited nano-particles.XRD,Raman-spectrum and FTIR patterns indicate that the product is a typical β-SiC.TEM images show that the nanowires have a wide diameter range from 10 to 100 nm,and some thin nanowires are bonded to the thick one by amorphous CVD-SiC.A SiC branch generates from an amorphous section of a thick one with an angle of 70° between them,which is consistent with the [111] axis stacking angle of the crystal.SAED and fast Fourier transform（FFT） patterns reveal that the nanowires can grow along with different axes,and the bamboo-nodes section is full of stacking faults and twin crystal.The twisted SiC lattice planes reveal that the screw dislocation growth is the main mechanism for the CVD-SiC nanowires.

Fluidized-bed chlorination thermodynamics and kinetics of Kenya natural rutile ore

Natural rutile and gaseous chlorine with carbon as reductant were used to prepare titanium tetrachloride. Thermodynamics and kinetics of chlorination of Kenya natural rutile particles in a batch-type fluidized bed were studied at 1173-1273 K. Thermodynamic analysis of this system revealed that the equation of producing CO was dominant at high temperatures. Based on the gas-solid multi-phase reaction theory and a two-phase model for the fluidized bed, the mathematical description for the chlorination reaction of rutile was proposed. The reaction parameters and the average concentration of gaseous chlorine in the emulsion phase were estimated. The average concentration of emulsion phase in the range of fluidized bed was calculated as 0.3 mol/m^3. The results showed that the chlorination of natural rutile proceeded principally in the emulsion phase, and the reaction rate was mainly controlled by the surface reaction.

In-situ homogeneous synthesis of carbon nanotubes on aluminum matrix and properties of their composites

Using nickel catalyst supported on aluminum powders, carbon nanotubes （CNTs） were successfully synthesized in aluminum powders by in-situ chemical vapor deposition at 650 ℃. Structural characterization revealed that the as-grown CNTs possessed higher graphitization degree and straight graphite shell. By this approach, more homogeneous dispersion of CNTs in aluminum powders was achieved compared with the traditional mechanical mixture methods. Using the in-situ synthesized CNTs/Al composite powders and powder metallurgy process, CNTs/Al bulk composites were prepared. Performance testing showed that the mechanical properties and dimensional stability of the composites were improved obviously, which was attributed to the superior dispersion of CNTs in aluminum matrix and the strong interfacial bonding between CNTs and matrix.

Preparation and characterization of diamond film on Cu substrate using Cu-diamond composite interlayer

Large area diamond films were fabricated on copper substrates by a multi-step process comprised of electroplating Cu-diamond composite layer on Cu substrate, plating a Cu layer to fix the protruding diamond particles, and depositing continuous diamond film on composite interlayer by hot-filament chemical vapor deposition （HFCVD）. The interface characteristics, internal stress and adhesion strength were investigated by scanning electron microscopy, Raman analysis and indentation test. The results show that the continuous film without cracks is successfully obtained. The microstructure of the film is a mixture of large cubo-octahedron grains grown from homo-epitaxial growth and small grains with （111） apparent facets grown from lateral second nuclei. The improved adhesion between diamond film and substrate results from the deep anchoring of the diamond particles in the Cu matrix and the low residual stress in the film.

Improved Epitaxy of 3C-SiC Layers on Si(100) by New CVD/LPCVD System

Single crystalline 3C-SiC epitaxial layers are grown on φ 50mm Si wafers by a new resistively heated CVD/LPCVD system,using SiH_4,C_2H_4 and H_2 as gas precursors.X-ray diffraction and Raman scattering measurements are used to investigate the crystallinity of the grown films.Electrical properties of the epitaxial 3C-SiC layers with thickness of 1～3μm are measured by Van der Pauw method.The improved Hall mobility reaches the highest value of 470cm 2/(V·s) at the carrier concentration of 7.7×10 17 cm -3 .

ZnO Films Synthesized by Solid-Source Chemical Vapor Deposition with c-Axis Parallel to Substrate

ZnO films with c -axis parallel to the substrate are reported.ZnO films are synthesized by solid-source chemical vapor deposition,a novel CVD technique,using zinc acetate dihydrate (solid) as the source material.The properties are characterized by X-ray diffraction,atomic force microscopy and transmission spectra.The parallel oriented ZnO films with mixed orientation for (100) and (110) planes are achieved on glass at the substrate temperature of 200℃ and the source temperature of 280℃,and a qualitative explanation is given for the forming of the mixed orientation.AFM images show that the surface is somewhat rough for the parallel oriented ZnO films.The transmission spectrum exhibits a high transmittance of about 85% in the visible region and shows an optical band gap about 3.25eV at room temperature.

Microstructures and formation mechanism of headstand pyrocarbon cones developed by electromagnetic-field-assisted CVD

Novel headstand pyrocarbon cones （HPCs） with hollow structure were developed on the surfaces of pyrocarbon layers of the carbon/carbon （C/C） composites at 650-750 °C by the electromagnetic-field-assisted chemical vapor deposition in the absence of catalysts. The fine microstructures of the HPCs were characterized by high-resolution transmission electron microscopy. The results show that the textural features of the HPCs directly transfer from turbostratic structure in roots to a well-ordered high texture in stems. And the degree of high texture ordering decreases gradually from the stem to the tail of the HPCs. The formation mechanism of the HPCs was inferred as the comprehensive effect of polarization induction on electromagnetic fields and particle-filler property under disruptive discharge.

Bending properties and fracture mechanism of C/C composites with high density preform

C/C composites with banded structure pyrocarbon were fabricated by fast chemical vapor infiltration（CVI）,with C3H6 as carbon source,N2 as carrier gas,and three-dimensional（3D） 12K PAN-based carbon fabric with high density of 0.94 g/cm3 as preform.Experimental results indicated that the fracture characteristics of C/C composites were closely related to the frequency of high-temperature treatment（HTT） at the break of CVI process.According to the load？displacement curves,C/C composites showed a pseudoplastic fracture after twice of HTT.After three times of HTT,load？displacement curves tended to be stable with a decreasing bending strength at 177.5 MPa.Delamination failure and intrastratal fiber fracture were observed at the cross-section of C/C composites by scanning electronic microscope.Because the content of pyrocarbon and fibers has a different distribution in layers,the C/C composites show different fracture characteristics at various regions,which leads to good toughness and bending strength.

Effect of deposition parameters on micro-and nano-crystalline diamond films growth on WC-Co substrates by HFCVD

The characteristics of hot filament chemical vapor deposition（HFCVD） diamond films are significantly influenced by the deposition parameters, such as the substrate temperature, total pressure and carbon concentration. Orthogonal experiments were introduced to study the comprehensive effects of such three parameters on diamond films deposited on WC-Co substrates. Field emission scanning electron microscopy, atomic force microscopy and Raman spectrum were employed to analyze the morphology, growth rate and composition of as-deposited diamond films. The morphology varies from pyramidal to cluster features with temperature decreasing. It is found that the low total pressure is suitable for nano-crystalline diamond films growth. Moreover, the substrate temperature and total pressure have combined influence on the growth rate of the diamond films.

In-situ investigation of atmospheric corrosion behavior of bronze under thin electrolyte layers using electrochemical technique

The atmospheric corrosion behavior of bronze under thin electrolyte layer （TEL） with different thicknesses was monitored using cathodic polarization curves, open circuit potential （OCP） and electrochemical impedance spectroscopy （EIS）. Cathodic polarization result indicates that the cathodic limiting current density increases with decreasing the TEL thickness. EIS result shows that the corrosion rate increases with decreasing the TEL thickness at the initial stage because the corrosion is dominated by the cathodic process, whereas after long immersion time, the corrosion degree with the TEL thickness is in the sequence of 150 μm 〉 310 μm〉 10μm ≈ bulk solution 〉 57 μm. The measurements of OCP and EIS present in-situ electrochemical corrosion information and their results are in good agreement with that of physical characterizations.