等离子体中的波动

分析了“冷”、“热”等离子体中波动现象的普遍色散关系 ,比较了其异同点 ,给出了反映“冷”等离子体中波动分类的CMA图和反映“热”等离子体中波动的 (ω ,k)

Effect of substrate temperature and oxygen plasma treatment on the properties of magnetron-sputtered CdS for solar cell applications

Cadmium sulfide(CdS)is an n-type semiconductor with excellent electrical conductivity that is widely used as an electron transport material(ETM)in solar cells.At present,numerous methods for preparing CdS thin films have emerged,among which magnetron sputtering(MS)is one of the most commonly used vacuum techniques.For this type of technique,the substrate temperature is one of the key deposition parameters that affects the interfacial properties between the target film and substrate,determining the specific growth habits of the films.Herein,the effect of substrate temperature on the microstructure and electrical properties of magnetron-sputtered CdS(MS-CdS)films was studied and applied for the first time in hydrothermally deposited antimony selenosulfide(Sb_(2)(S,Se)_(3))solar cells.Adjusting the substrate temperature not only results in the design of the flat and dense film with enhanced crystallinity but also leads to the formation of an energy level arrangement with a Sb_(2)(S,Se)_(3)layer that is more favorable for electron transfer.In addition,we developed an oxygen plasma treatment for CdS,reducing the parasitic absorption of the device and resulting in an increase in the short-circuit current density of the solar cell.This study demonstrates the feasibility of MS-CdS in the fabrication of hydrothermal Sb_(2)(S,Se)_(3)solar cells and provides interface optimization strategies to improve device performance.

Synthesis of Ni-CeO_2 catalyst for the partial oxidation of methane using RF thermal plasma

Ni‐CeO2 catalysts with a nickel content of 50 mol% were prepared using RF thermal plasma, and their catalytic activities for methane partial oxidation were characterized. For the synthesis of Ni‐CeO2 catalysts, a precursor containing Ni（～5‐μm diameter） and CeO2（～200‐nm diameter）powders were heated simultaneously using an RF plasma at a power level of ～52 kVA and a powder feeding rate of ～120 g/h. From the X‐ray diffraction data and transmission electron microscopy images, the precursor formed into high crystalline CeO2 supports with nanosized Ni particles（ 50‐nm diameter） on their surfaces. The catalytic performance was evaluated under atmospheric pressure at 500 °C and a CH4：O2 molar ratio of 2：1 with Ar diluent. Although the Ni content was high（～50 mol%）, the experimental results reveal a methane conversion rate of 70%, selectivities of CO and H2 greater than 90% and slight carbon coking during an on‐stream test at 550 °C for 24 h.However, at 750 °C, the on‐stream test revealed the formation of filament‐like carbons with an increased methane conversion rate over 90%.

Effect of Injecting Inert Particles on Coking Prohibition and Particle Velocity Uniformization in Downer Reactors

The coking observation and particle flow behaviour in both thermal plasma and cold plexiglas downers were investigated in a binary particle system formed by injecting coarse inert particles (carrying coke away and scouring wall) and fine coal powders into the downer reactor. The results demonstrate that this scheme is a rational selection to prevent coking on downer walls and improve particle velocity distribution along the radial direction. When injected coarse particles mixed with fine powders in downers, the fluctuation of local particle velocity in the radial direction becomes smaller and two peaks in the radial distribution of local particle velocity occur due to the improved dispersing character and flow structure, which are beneficial to the thermo-plasma coal cracking reaction and coking prevention.

Theoretical and experimental investigation of Ti alloy powder production using low-power plasma torches

This study was carried out to investigate the possibility of titanium alloy metal powder production using low-power plasma torches.An argon DC non-transferred arc plasma torch was designed,and numerical analysis was conducted to determine the plasma jet properties and wire temperature.The highest velocities inside the nozzle attachment were between 838 and 1178 m/s.The velocities of the jets at the apex were between 494 and 645 m/s for different gas flow rates.The studied plasma gas flow rates had no significant effect on the effective plasma jet length.It was shown that the plasma jet length can be estimated by numerical analysis using the temperature and velocity changes of the plasma jet over distance.It was observed that the powders produced were spherical without any satellites.As a result of this study,a plasma torch was developed and powder production was performed successfully by using relatively low torch power.

Compressive and Rarefactive Waves in Dust Plasma with Non-thermal Ions

The governing equation of the dust fluid with non-thermal ions and variable dust charge on dust particles in hot dust plasmas is obtained. Both the compressive and rarefactive waves in this system are investigated. They can be determined by plasma parameters including the temperatures of （lust fluid, ions and electrons, as well as the non-thermal parameter of ions, and the number densities of the dust particles, the ions and the electrons, etc.

Improving tribological and thermal properties of Al alloy using CNTs and Nb nanopowder via SPS for power transmission conductor

This study aimed at improving the tribological and thermal properties of Al alloy using CNTs and Nb nanopowder as reinforcements and spark plasma sintering(SPS)as the fabrication method.The SPS was conducted at 630℃,30 MPa,10 min,and 200℃/min.The tribology test was run with ball-on-disc tribometer using steel ball as the counter body.And the thermal test was processed with thermogravimetric analyzer(TGA)and laser flash apparatus(LFA).Results showed that the addition of 8 wt.%CNTs and 8 wt.%Nb reinforcements respectively decreased the coefficient of friction(COF)of the composite by 79%.The wear volume of the composite was decreased by 23%,and so was the wear rate.However,the thermal conductivity of the composite was equally improved by 44%.The tribology improvement was stimulated by a C film generated by CNTs and a protective Nb2O5 formed by Nb nanopowder.The thermal conductivity was improved by the grain refining property of Nb and the high thermal conductivity of CNTs.Therefore,these results indicated that Al-CNTs-Nb composite is a robust material for high transmission conductor capable of reducing sag and ensuring the durability of the composite.

CO_2 laser-micro plasma arc hybrid welding for galvanized steel sheets

A laser lap welding process for zinc-coated steel has a well-known unsolved problem-porosity formation. The boiling temperature of coated zinc is lower than the melting temperature of the base metal, which is steel. In the autogenous laser welding, the zinc vapor generates from the lapped surfaces expels the molten pool and the expulsion causes numerous weld defects, such as spatters and blow holes on the weld surface and porosity inside the welds. The laser-arc hybrid welding was suggested as an alternative method for the laser lap welding because the arc can preheat or post-beat the weldment according to the arrangement of the laser beam and the arc. CO2 laser-micro plasma hybrid welding was applied to the lap welding of zinc-coated steel with zero-gap. The relationships among the weld quality and process parameters of the laser-arc arrangement, and the laser-arc interspacing distance and arc current were investigated using a full-factorial experimental design. The effect of laser-arc arrangement is dominant because the leading plasma arc partially melts the upper steel sheets and vaporizes or oxidizes the coated zinc on the lapped surfaces. Compared with the result from the laser-TIG hybrid welding, the heat input from arc can be reduced by 40%.

ICRF Heated Long-Pulse Plasma Discharges in LHD

A long-pulse plasma discharge for more than 30 min. was achieved on the Large Helical Device （LHD）. A plasma of ne = 0.8 × 10^19 m^-3 and T10 = 2.0 keV was sustained with PICH = 0.52 MW, PECH = 0.1 MW and averaged PNBI = 0.067 MW. Total injected heating energy was 1.3 G J, which was a quarter of the prepared RF heating energy. One of the keys to the success of the experiment was a dispersion of the local plasma heat load to divertors, accomplished by shifting the magnetic axis inward and outward.

Influence of Atmospheric Non-thermal Plasma on Some Hematological Characteristics of Iraqi Patients

Non-thermal atmospheric pressure plasma has emerged as a new promising tool in medicine. The effectiveness of an Atmospheric Non Thermal Plasma for clinical and biological applications is studied. This research effort includes a desioning of plasma generating system and examine it on some medical and biological parameters. No patient had previous operative or chemotherapeutic treatment, so the patients with hematological disorders （hemophilia） and those with open heart surgery that receiving warfarin and other antithrombotic agents were excluded from the study. A total of eighty 80 Iraqi patients seeking for a medical consultation in A1-Ramadi Teaching Hospital were included in this study. The plasma treatment is applied both in vitro and in vivo experiments on those patients. In the in vivo experiments, the bleeding time tests were carried out on these patients; the results showed the bleeding time of the patients was reduced as compared with control. In vitro experiments regarding clotting time and prothrombine time PT, the results have demonstrated that this plasma device clots blood rapidly via a control. The dependencies of the degree of clotting on the exposure time, distance have been recorded. A series of experiments reveal that this effectiveness is due to the ability of direct discharge to bring charges to blood samples due to generation of so many mediators like reactive nitrogen species and free radicals.

Low Temperature Plasma CVD Grown Graphene by Microwave Surface-Wave Plasma CVD Using Camphor Precursor

Hydrocarbon precursor such as methane has been widely used to grow graphene films and the methods of growing quality graphene films are dominated by thermal CVD （chemical vapor deposition） system. Graphene films grown by plasma process are generally highly defective which in turns degrade the quality of the films. Here, using a green precursor, camphor we demonstrate a simple and economical method to get high-quality graphene film on copper substrate by micro wave surface-wave plasma CVD at relatively low temperature 550℃. Graphene film grown using camphor shows superior quality than that of the film grown using methane. Results revealed that camphor precursor is a good alternative to hydrocarbon precursors for graphene research.

Charge and Levitation of Grains in Plasma Sheath with Dust Thermic Emission

By taking into account thermic emission current from hot dust surface, the problem involved in dust charging and levitation of dust grains in plasma sheath has been researched. The results are compared to that without including thermal emission current while the system parameters are same. It is found that the thermal emission current has played a significant role on modifying the dust charging and balance levitations. Both of the charging numbers of dust and the dust radius in balance are dramatically reduced. The stability of dust levitation is also analyzed and discussed.

（2＋1）-Dimensional Electron Acoustic Solitary Waves in an Unmagnetized Collisionless Plasma with Vortex-Like Hot Electrons

In this paper, （2＋1）-dimensional electron acoustic waves （EAW） in an unmagnetized collisionless plasma have been studied by the linearized method and the reductive perturbation technique, respectively. The dispersion relation and a modified Kadomtsev-Petviashvili （KP） equation have been obtained for the EAW in the plasma considering a cold electron fluid and a vortex-like hot electrons. It is found from some numerical results that the parameter β（the ratio of the free hot electron temperature to the hot trapped electron temperature） effects on the amplitude and the Width of the electron acoustic solitary waves （EASW）. It can be indicated that the free hot electron temperature and the hot trapped electron temperature have very important effect on the characters of the propagation for the EASW.

Nitrogen Plasma Treatment Effect on Graphene Sheeted Vertically Aligned Carbon Nanofibers

Nitrogen plasma treatment effect on GS-CNFs （graphene seeted vertically aligned carbon nanofibers） has been studied. GS-CNFs were grown on nickel coated cupper substrates by DC-plasma CVD （chemical vapor deposition） at relatively low temperature. GS-CNFs were studied by SEM （scanning electron microscopy）, HR-TEM （high-resolution transmission electron microscopy）, XPS and Raman measurements. GS-CNFs are composed of cylindrical shaped having pure graphite sheets with about 5 μm length and nanometer size tips and roots diameter. Nitrogen plasma treatment causes nitrogen chemical etching on the graphene seeted carbon nanofibers were disordered its fine shape and increase the graphetization due to nitrogen incorporation.

Non-Thermal Plasma Assisted Reforming of Ethanol in Dynamic Plasma-Liquid Systems

The paper presents experimental and theoretical studies of non-thermal plasma assisted reforming of liquid ethanol into hydrogen-rich syngas in dynamic plasma-liquid systems （PLS） using electric DC and pulsed discharges in a gas channel with liquid wall （DGCLW） and DC discharge in a reverse vortex gas flow of Tornado type with ＂liquid＂ electrode （TORNADO-LE）. Results of experiments show the energy efficiency of plasma-chemical conversion of ethanol in studied systems. Results of model calculations explain the kinetic mechanism of non-equilibrium plasma-chemical transformations in different conditions. The proposed technique of plasma-fuel reforming can be used in alternative biofuels combustion technologies in advanced diesel engines and power plants.

Effects of various sintering methods on microstructure and mechanical properties of CP-Ti powder consolidations

Effects of various sintering methods such as spark plasma sintering(SPS), hot pressing(HP) and electric resistance sintering(ERS) on the microstructure and mechanical properties of commercial pure titanium(CP-Ti) powder consolidations with particle size of <147 μm, <74 μm and <43 μm were studied. The smaller particle powders are densified to proceed at a higher rate. Dense titanium with relative density up to 99% is found to take place at 850 °C under 30 MPa of SPS and HP condition. However, in case of ERS, CP-Ti powders were densified almost at 950 °C under 30 MPa. The microstructure of sintered titanium is composed of equiaxed grains at 850-950 °C. The yield strength of sintered body composed of <43 μm powder is 858 MPa by using SPS at 850 °C under 30 MPa. When there is a higher content of small particle, the higher yield strength value is obtained both by using SPS and HP. However, when ERS is introduced, the highest yield strength is 441 MPa at 950 °C under 30 MPa, which shows much lower values than those by SPS and HP methods. ERS method takes much less sintering time compared with SPS and HP. Nevertheless, higher sintering temperature results in lower strength and elongation because of brittle fracture.

Organotemplate-free Hydrothermal Synthesis of SUZ-4 Zeolite: Influence of Synthesis Conditions

Various conditions were investigated in detail for the novel organic template-free static hydrothermal synthesis of SUZ-4 zeolite in the presence of seeds. The obtained samples were characterized by XRD （X-ray diffraction）, SEM （scanning electron microscope）, TG （thermal gravimetric analysis）, ICP （inductively coupling plasma） elemental analysis, nitrogen sorption isotherm and surface area. The results show that pure SUZ-4 zeolites with high crystallinity are obtained in a broad window of synthesis conditions： seed mass concentration 0.2%-2%, SIO2/A1203 molar ratio 21 25, KOH/SiO2 molar ratio 0.33 0.43, H20/SiO2 molar ratio 7.14-38.1, aging time 24 h, crystallization temperature 160℃, and crystallization time 6-10 d. Also, crystallinity and size of the rod-like SUZ-4 zeolite crystals are found to alter with the conditions.

Getting Free Heat Energy Based on Cavitation and Nuclear Fusion according to Revinov＇s Pilot Plants

In this report, the author describes and compares two innovative processes for producing thermal energy based on cavitation and nuclear fusion reactions in the indoor environment. Experiments conducted in the laboratory IHS （Intensive Heating System） of IE ＂Revinov N. M.＂ indicate that the process of lasso-vortex cavitation, which generates by means of an electric arc obtained HV-EI, gas-liquid plasma state in the EHH-CTC （electro-hydraulic heater with cavitation thermal camera） is not inferior and sometimes even superior in heat transfer to NF-AC （nuclear fusion reactions in ambient conditions）.

Calculation of Dielectric Function of a Quark-Gluon Plasma

With the hard thermal loop （HTL） resummation technique, we calculate the dielectric function excited by hard gluon in quark-gluon plasma （QCP）. We find that in a section of the space-like region po/p ∈ [0.78, 0.95], there are two extremum structures on the dielectric function curve, while the dielectric function in the HTL approximation decreases monotonously without these properties. Through the analyses of the imaginary part of the dielectric function, we conclude that the character of the dielectric function in this region reflects effects of the Landau damping.

The First Principle Formula of the Relativistic Heat Conductivity of Coulomb Electronic Plasmas

Making use of the relativistic BBGKY technique,the relativistic generalization of Landau collision integral is obtained.Furthermore,we calculate the relativistic hydrodynamic modes up to the second order in the hydrodynamic wave number.Combining Résibois' method,we present the first principle formula of the relativistic heat conductivity of Coulomb electronic plasmas for low-order corrections.