Production of carbon anodes by high-temperature mould pressing

Laboratory-scale carbon anodes were produced by a new method of high temperature mould pressing, and their physico-chemical properties were studied. The influence of mould pressing conditions and coal pitch addition on the bulk density, crushing strength, and oxidation resistance was analyzed. The mierostructure of carbon anodes was investigated by scanning electron microscopy （SEM）, and the mechanism of producing carbon anodes by high-temperature mould pressing was analyzed. The results show that when the anodes are produced by high-temperature mould pressing, coal pitch can expand into the coke particles and fill the pores inside the particles, which is beneficial for improving the quality of prebaked anodes. The bulk density of carbon anodes is 1.64-1.66 g/cm3, which is 0.08-0.12 g/cm3 higher than that of industrial anodes, and the oxidation resistance of carbon anodes is also significantly improved.

Analysis and modeling of alumina dissolution based on heat and mass transfer

A comprehensive heat and mass transfer model of dissolution process of non-agglomerated and agglomerated alumina particles was established in an aluminum reduction cell. An appropriate finite difference method was used to calculate the size dissolution rate, dissolution time and mass of alumina dissolved employing commercial software and custom algorithm based on the shrinking sphere assumption. The effects of some convection and thermal condition parameters on the dissolution process were studied. The calculated results show that the decrease of alumina content or the increase of alumina diffusion coefficient is beneficial for the increase of size dissolution rate and the decrease of dissolution time of non-agglomerated particles. The increase of bath superheat or alumina preheating temperature results in the increase of size dissolution rate and the decrease of dissolution time of agglomerated particles. The calculated dissolution curve of alumina（mass fraction of alumina dissolved） for a 300 k A aluminum reduction cell is in well accordance with the experimental results. The analysis shows that the dissolution process of alumina can be divided into two distinct stages： the fast dissolution stage of non-agglomerated particles and the slow dissolution stage of agglomerated particles, with the dissolution time in the order of 10 and 100 s, respectively. The agglomerated particles were identified to be the most important factor limiting the dissolution process.

Influence of oxidation heat on hard anodic film of aluminum alloy

The special experimental device and sulfuric acid electrolyte were adopted to study the influence of anodic oxidation heat on hard anodic film for 2024 aluminum alloy. Compared with the oxidation heat transferred to the electrolyte through anodic film, the heat transferred to the coolant through aluminum substrate is more beneficial to the growth of anodic film. The film forming speed, film thickness, density and hardness are significantly increased as the degree of undercooling of the coolant increases. The degree of undercooling of the coolant, which is necessary for the growth of anodic film, is related to the degree of undercooling of the electrolyte, thickness of aluminum substrate, thickness of anodic film, natural parameters of bubble covering and current density. The microstructure and performance of the oxidation film could be controlled by the temperature of the coolant.

Effect of electrolysis superheat degree on anticorrosion performance of 5Cu/(10NiO-NiFe_2O_4) cermet inert anode

5Cu/(10NiO-NiFe2O4) cermet inert anodes were prepared by cold-pressing and sintering process, and the effect of superheat degree of melting K3AlF6-Na3AlF6-AlF3 on their anticorrosion performance was studied under electrolysis conditions. The results show that, the fluctuation of cell becomes small with increasing of superheat degree, which is helpful to inhibit the formation of cathodic encrustation; the concentration of impurities from inert anode in bath goes up to certain degree, but it is far smaller than those in traditional high-temperature bath. Increasing the superheat degree of melting K3AlF6-Na3AlF6-AlF3 has unconspicuous effect on the contents of impurities in cathodic aluminum. The total mass fractions of Fe, Ni and Cu in aluminum are 15.38% and 15.09% respectively under superheat degree of 95 and 195 ℃. From micro-topography of anode used view, increasing the superheat degree can aggravate corrosion of metal Cu in inert anode, and has negative influence on electrical conductivity of electrode to some extent.

Grain refining action of Ti existing in electrolytic low-titanium aluminum with Al-4B addition for superheated Al melt

The effects of superheating temperature on the grain refining efficiency of Ti existing in electrolytic low-titanium aluminum(ELTA)without and with the Al-4B addition and the Al-5Ti-1B master alloy in pure Al were comparatively investigated. The results show that the Ti existing in ELTA without Al-4B addition exhibits a certain grain refining efficiency when the melt superheating temperature is lower,but the efficiency decreases rapidly when the superheating temperature is higher.The grain refining efficiency of the Al-5Ti-1B master alloy is better than that of the Ti existing in ELTA without Al-4B addition at any superheating temperature,but it also decreases obviously with the increase of the superheating temperature.One important reason is that the TiB2 particles coming from the Al-5Ti-1B master alloy can settle down at the bottom of the Al melt easily when the superheating temperature is increased,thus decrease the number of the potent heterogeneous nuclei retained in the Al melt.If the Al-4B master alloy is added to the ELTA melt,the grain refining efficiency of the Ti existing in ELTA can be improved significantly, and does not decrease with the increase of the superheating temperature.This perhaps provides us a possible method to suppress the effect of the superheated melt on the microstructures of aluminum..

Effect of working condition on thermal stress of NiFe_2O_4-based cermet inert anode in aluminum electrolysis

Based on the FEA software ANSYS,a model was developed to simulate the thermal stress distribution of inert anode.In order to reduce its thermal stress,the effect of some parameters on thermal stress distribution was investigated,including the temperature of electrolyte,the current,the anode cathode distance,the anode immersion depth,the surrounding temperature and the convection coefficient between anode and circumstance.The results show that there exists a large axial tensile stress near the tangent interface between the anode and bath,which is the major cause of anode breaking.Increasing the temperature of electrolyte or the anode immersion depth will deteriorate the stress distribution of inert anode.When the bath temperature increases from 750 to 970 ℃,the maximal value and absolute minimal value of the 1st principal stress increase by 29.7% and 29.6%,respectively.When the anode immersion depth is changed from 1 to 10 cm,the maximal value and absolute minimal value of the 1st principal stress increase by 52.1% and 65.0%,respectively.The effects of other parameters on stress distribution are not significant.