The application of multi-hull ship or trimaran vessel as a mode of transports in both river and sea environments have grown rapidly in recent years.Trimaran vessels are currently of interest for many new high speed sh...The application of multi-hull ship or trimaran vessel as a mode of transports in both river and sea environments have grown rapidly in recent years.Trimaran vessels are currently of interest for many new high speed ship projects due to the high levels of hydrodynamic efficiency that can be achieved,compared to the mono-hull and catamaran hull forms.The purpose of this study is to identify the possible effects of using an unsymmetrical trimaran ship model with configuration(S/L) 0.1-0.3 and R/L=0.1-0.2.Unsymmetrical trimaran ship model with main dimensions: L=2000mm,B=200 mm and T=45 mm.Experimental methods(towing tank) were performed in the study using speed variations at Froude number 0.1-0.6.The ship model was pulled by an electric motor whose speed could be varied and adjusted.The ship model resistance was measured precisely by using a load cell transducer.The comparison of ship resistance for each configuration with mono-hull was shown on the graph as a function of the total resistance coefficient and Froude number.The test results found that the effective drag reduction could be achieved up to 17% at Fr=0.35 with configuration S/L=0.1.展开更多
The research on underwater ship-hull cleaning robot was conducted on the purpose of realizing the automation of cleaning underwater ship hull so that service life of ship will be prolonged and ship speed will raised. ...The research on underwater ship-hull cleaning robot was conducted on the purpose of realizing the automation of cleaning underwater ship hull so that service life of ship will be prolonged and ship speed will raised. Moreover, fuel consumption and the work intensity of divers will be reduced. In this paper, the current situation and the latest technology in China and abroad were analyzed;meanwhile, the typical characteristics of the underwater cleaning robot were introduced. According to the work principle of the underwater cleaning robot, the emphasis was put on the analysis and study of permanent-magnetic absorption, magnetic wheel, airproof and anticorrosion, underwater cleaning equipment and control system. The robot is easy in rotation and simple in control.展开更多
Experimental investigations into the collapse behavior of a box-shape hull girder subjected to extreme wave-induced loads are presented.The experiment was performed using a scaled model in a tank.In the middle of the ...Experimental investigations into the collapse behavior of a box-shape hull girder subjected to extreme wave-induced loads are presented.The experiment was performed using a scaled model in a tank.In the middle of the scaled model,sacrificial specimens with circular pillar and trough shapes which respectively show different bending moment-displacement characteristics were mounted to compare the dynamic collapse characteristics of the hull girder in waves.The specimens were designed by using finite element(FE)-analysis.Prior to the tank tests,static four-point-bending tests were conducted to detect the load-carrying capacity of the hull girder.It was shown that the load-carrying capacity of a ship including reduction of the capacity after the ultimate strength can be reproduced experimentally by employing the trough type specimens.Tank tests using these specimens were performed under a focused wave in which the hull girder collapses under once and repetitive focused waves.It was shown from the multiple collapse tests that the increase rate of collapse becomes higher once the load-carrying capacity enters the reduction path while the increase rate is lower before reaching the ultimate strength.展开更多
A new multi-level analysis method of introducing the super-element modeling method, derived from the multi-level analysis method first proposed by O. F. Hughes, has been proposed in this paper to solve the problem of ...A new multi-level analysis method of introducing the super-element modeling method, derived from the multi-level analysis method first proposed by O. F. Hughes, has been proposed in this paper to solve the problem of high time cost in adopting a rational-based optimal design method for ship structural design. Furthermore,the method was verified by its effective application in optimization of the mid-ship section of a container ship. A full 3-D FEM model of a ship,suffering static and quasi-static loads, was used as the analyzing object for evaluating the structural performance of the mid-ship module, including static strength and buckling performance. Research results reveal that this new method could substantially reduce the computational cost of the rational-based optimization problem without decreasing its accuracy, which increases the feasibility and economic efficiency of using a rational-based optimal design method in ship structural design.展开更多
This paper addresses the development and testing of a remotely controlled boat platform with an innovative air-ventilated hull. The application of air cavities on the underside of ship hulls is a promising means for r...This paper addresses the development and testing of a remotely controlled boat platform with an innovative air-ventilated hull. The application of air cavities on the underside of ship hulls is a promising means for reducing hydrodynamic drag and pollutant emissions and increasing marine transportation efficiency. Despite this concept's potential, design optimization and high-performance operation of novel air-cavity ships remain a challenging problem. Hull construction and sensor instrumentation of the model-scale air-cavity boat is described in the paper. The modular structure of the hull allows for easy modifications, and an electric propulsion unit enables self-propelled operation. The boat is controlled remotely via a radio transmission system. Results of initial tests are reported, including thrust, speed, and airflow rate in several loading conditions. The constructed platform can be used for optimizing air-cavity systems and testing other innovative hull designs. This system can be also developed into a high-performance unmanned boat.展开更多
Methods used for digital ship design were studied and formed the basis of a proposed frame model suitable for ship construction modeling. Based on 3-D modeling software, a digital design system for hull structures was...Methods used for digital ship design were studied and formed the basis of a proposed frame model suitable for ship construction modeling. Based on 3-D modeling software, a digital design system for hull structures was developed. Basic software systems for modeling, modifying, and assembly simulation were developed. The system has good compatibility, and models created by it can be saved in different 3-D file formats, and 2D engineering drawings can be output directly. The model can be modified dynamically, overcoming the necessity of repeated modifications during hull structural design. Through operations such as model construction, intervention inspection, and collision detection, problems can be identified and modified during the hull structural design stage. Technologies for centralized control of the system, database management, and 3-D digital design are integrated into this digital model in the preliminary design stage of shipbuilding.展开更多
As a new type of hull form,trimaran has remarkable excellent performances and has drawn more and more attention.When the viscous CFD technology now available is applied to the research of resistance performance of tri...As a new type of hull form,trimaran has remarkable excellent performances and has drawn more and more attention.When the viscous CFD technology now available is applied to the research of resistance performance of trimaran,the spatial discretization would usually result in the grid error and uncertainty,and thus the considerable discrepancy between the numerical results and the experimental data.In order to ascertain how much the grid would affect the calculation,the grid convergence should be studied.A mathematical trimaran was chosen as an example,with the commercial code CFX for the simulation,VOF for surface treatment,and the grid study was carried out based on two different turbulence models.It was concluded that carrying out grid study is helpful in estimating the grid error and uncertainty,and indicating the direction of improving the credibility of the numerical calculation, and,in addition to grid errors and uncertainties,the turbulence modeling errors and uncertainties contribute to the simulation errors.展开更多
Multihull ships are widely used for sea transportation, and those with four hulls are known as quadramarans. Hull position configurations of a quadramaran include the diamond, tetra, and slice. In general, multihull v...Multihull ships are widely used for sea transportation, and those with four hulls are known as quadramarans. Hull position configurations of a quadramaran include the diamond, tetra, and slice. In general, multihull vessels traveling at high speeds have better hydrodynamic efficiency than monohull ships. This study aims to identify possible effects of various quadramaran hull position configurations on ship resistance for hull dimensions of 2 m length, 0.21 m breadth, and 0.045 m thickness. We conducted a towing test in which we varied the hull spacing and speed at Fr values between 0.08 and 0.62 and measured the total resistance using a load cell transducer. The experimental results reveal that the lowest total resistance was achieved with a diamond quadramaran configuration at Fr = 0.1-0.6 and an effective interference factor of up to 0.35 with S/L = 3/10 and R/L = 1/2 at Fr = 0.62.展开更多
The flexible transmission shaft and wheel propeller are combined as the kinetic source equipment, which realizes the nmlti-motion modes of the autonomous underwater vehicle (AUV) such as vectored thruster and wheele...The flexible transmission shaft and wheel propeller are combined as the kinetic source equipment, which realizes the nmlti-motion modes of the autonomous underwater vehicle (AUV) such as vectored thruster and wheeled movement. In order to study the interactional principle between the hull and the wheel propellers while the AUV navigating in water, the computational fluid dynamics (CFD) method is used to simulate numerically the unsteady viscous flow around AUV with propellers by using the Reynolds-averaged Navier-Stokes (RANS) equations, shear-stress transport (SST) k-w model and pressure with splitting of operators (PISO) algorithm based on sliding mesh. The hydrodynamic parameters of AUV with propellers such as resistance, pressure and velocity are got, which reflect well the real ambient flow field of AUV with propellers. Then, the semi-implicit method for pressure-linked equations (SIMPLE) algorithm is used to compute the steady viscous flow field of AUV hull and propellers, respectively. The computational results agree well with the experimental data, which shows that the numerical method has good accuracy in the prediction of hydrodynamic performance. The interaction between AUV hull and wheel propellers is predicted qualitatively and quantitatively by comparing the hydrodynamic parameters such as resistance, pressure and velocity with those from integral computation and partial computation of the viscous flow around AUV with propellers, which provides an effective reference to the shady on noise and vibration of AUV hull and propellers in real environment. It also provides technical support for the design of new AUVs.展开更多
The hydrodynamic analysis of a new semi-small waterplane area twin hull (SWATH) suitable for various applications such as small and medium size passenger ferries is presented. This may be an attractive crossover con...The hydrodynamic analysis of a new semi-small waterplane area twin hull (SWATH) suitable for various applications such as small and medium size passenger ferries is presented. This may be an attractive crossover configuration resulting from the merging of two classical shapes: a conventional SWATH and a fast catamaran. The final hull design exhibits a wedge-like waterline shape with the maximum beam at the stem; the hull ends with a very narrow entrance angle, has a prominent bulbous bow typical of SWATH vessels, and features full stern to arrange waterjet propellers. Our analysis aims to perform a preliminary assessment of the hydrodynamic performance of a hull with such a complex shape both in terms of resistance of the hull in calm water and seakeeping capability in regular head waves and compare the performance with that of a conventional SWATH. The analysis is performed using a boundary element method that was preliminarily validated on a conventional SWATH vessel.展开更多
An experimental investigation is performed to assess the relation of interference performance on the total resistance of a pentamaran model advancing in calm water. For this motivation, the total drag of the ship is ...An experimental investigation is performed to assess the relation of interference performance on the total resistance of a pentamaran model advancing in calm water. For this motivation, the total drag of the ship is performed for several values of asymmetric outrigger configuration and hull separation, altering the Froude number in the range 0.3–0.9. Our results indicate that remarkable changes in resistance require notable changes in transverse distance values (hull separation) when wave interference may occur. In addition, there is no single configuration that consistently outperforms the other configurations across the entire speed range and the optimum interference factor -0.2 appears at a Froude number of 0.45 in S/L=0.33 with the outrigger outer position: asymmetric outboard for A3 configuration.展开更多
Small water-plane area twin-hull(SWATH) has drawn the attention of many researchers due to its good sea-keeping ability.In this paper,MMG's idea of separation was used to perform SWATH movement modeling and simulat...Small water-plane area twin-hull(SWATH) has drawn the attention of many researchers due to its good sea-keeping ability.In this paper,MMG's idea of separation was used to perform SWATH movement modeling and simulation;respectively the forces and moment of SWATH were divided into bare hull,propeller,rudder at the fluid hydrodynamics,etc.Wake coefficient at the propellers which reduces thrust coefficient,and rudder mutual interference forces among the hull and propeller,for the calculation of SWATH,were all considered.The fourth-order Runge-Kutta method of integration was used by solving differential equations,in order to get SWATH's movement states.As an example,a turning test at full speed and full starboard rudder of ‘Seagull' craft is shown.The simulation results show the SWATH's regular pattern and trend of motion.It verifies the correctness of the mathematical model of the turning movement.The SWATH's mathematical model is applied to marine simulator in order to train the pilots or seamen,or safety assessment for ocean engineering project.Lastly,the full mission navigation simulating system(FMNSS) was determined to be a successful virtual reality technology application sample in the field of navigation simulation.展开更多
This study presents a numerical method for optimizing hull form in calm water with respect to total drag which contains a viscous drag and a wave drag. The ITTC 1957 model-ship correlation line was used to predict fri...This study presents a numerical method for optimizing hull form in calm water with respect to total drag which contains a viscous drag and a wave drag. The ITTC 1957 model-ship correlation line was used to predict frictional drag and the corrected linearized thin-ship theory was employed to estimate the wave drag The evolution strategy (ES) which is a member of the evolutionary algorithms (EAs) family obtains an optimum hull form by considering some design constraints. Standard Wigley hull is considered as an initial hull in optimization procedures for two test cases and new hull forms were achieved at Froude numbers 0.24, 0.316 and 0.408. In one case the ES technique was ran for the initial hull form, where the main dimensions were fixed and the only variables were the hull offsets. In the other case in addition to hull offsets, the raain dimensions were considered as variables that are optimized simultaneously. The numerical results of optimization procedure demonstrate that the optimized hull forms yield a reduction in total drag.展开更多
In order to get some useful parameters for grid generation of catamaran, the CFD software FLUENT is used to investigate the main effects of grid generation on flow field calculation. The influences of some elements ar...In order to get some useful parameters for grid generation of catamaran, the CFD software FLUENT is used to investigate the main effects of grid generation on flow field calculation. The influences of some elements are investigated with a series of calculations in the present paper, and some alteratives are proposed. The proposed alteratives based on the analysis of the effects are used for a catamaran resistance calculation, comparisons of the calculated results with experimental data show good agreement. It shows that the research result of this paver is useful for the numerical calculation of catamaran.展开更多
In the present analysis, several parameters used in a numerical simulation are investigated in an integrated study to obtain their influence on the process and results of this simulation. The parameters studied are el...In the present analysis, several parameters used in a numerical simulation are investigated in an integrated study to obtain their influence on the process and results of this simulation. The parameters studied are element formulation, friction coefficient, and material model. Numerical simulations using the non-linear finite element method are conducted to produce virtual experimental data for several collision scenarios. Pattern and size damages caused by collision in a real accident case are assumed as real experimental data, and these are used to validate the method. The element model study performed indicates that the Belytschko-Tsay element formulation should be recommended for use in virtual experiments. It is recommended that the real value of the friction coefficient for materials involved is applied in simulations. For the study of the material model, the application of materials with high yield strength is recommended for use in the side hull structure.展开更多
A combination of methods was developed that can determine hydrodynamic forces on a planing hull in steady motion.Firstly,a potential-based boundary-element method was used to calculate the hydrodynamic pressure,induce...A combination of methods was developed that can determine hydrodynamic forces on a planing hull in steady motion.Firstly,a potential-based boundary-element method was used to calculate the hydrodynamic pressure,induced resistance and lift.Then the frictional resistance component was determined by the viscous boundary layer theory.Finally,a particular empirical technique was applied.to determine the region of upwash geometry and determine spray resistance.Case studies involving four models of Series 62 planing craft were run.These showed that the suggested method is efficient and capable,with results that are in good agreement with experimental measurements over a wide range of volumetric Froude numbers.展开更多
Tension leg platform (TLP) has been one of the most favorite deep-water platform concepts for offshore oil and gas field exploration and development. As of now,a total of 24 TLPs have been installed worldwide with 3 m...Tension leg platform (TLP) has been one of the most favorite deep-water platform concepts for offshore oil and gas field exploration and development. As of now,a total of 24 TLPs have been installed worldwide with 3 more to be installed in the near future and 5 more under design. Most of these installations are in the Gulf of Mexico (GoM). Water depths for these TLP installations range from 150 m to 1 600 m. It is highly expected that China will have her first TLP designed,fabricated,and installed in the very near future. In order to satisfy the need for a unified hull structural design practice,this paper presents the design philosophy of a conventional TLP hull structure with emphases on critical structural components design and analysis methodologies.展开更多
A geometrically similar scaling was made from small-scale specimen to full-scale stiffened panels and then their collapse behaviour is investigated. It is considered that the stiffened panel compressive ultimate stren...A geometrically similar scaling was made from small-scale specimen to full-scale stiffened panels and then their collapse behaviour is investigated. It is considered that the stiffened panel compressive ultimate strength test was designed according to geometrical scaling laws so that the output of the test could be used as representative of the stiffened panels of the compressive zone of a tanker hull subjected to vertical bending moment. The ultimate strength of a tanker hull is analysed by a FE analysis using the experimentally developed master stress-strain curves which are obtained by the beam tension test and the compressive test of the stiffened panel, and are then compared with the result achieved by the progressive collapse method.展开更多
A method of reliability analysis based on a direct strength calculation employing the von Mises stress failure criterion is presented here. The short term strain distributions of ship hull structural components are id...A method of reliability analysis based on a direct strength calculation employing the von Mises stress failure criterion is presented here. The short term strain distributions of ship hull structural components are identified through the statistical analysis of the wave-induced strain history and the long term distributions by the weighted summation of the short term strain distributions. The wave-induced long term strain distribution is combined with the still water strain. The extreme strain distribution of the response strain is obtained by statistical analysis of the combined strains. The limit state function of the reliability analysis is based on the von Mises stress failure criterion, including the related uncertainties due to the quality of the material and model uncertainty. The reliability index is calculated using FORM and sensitivity analysis of each variable that has effects on the reliability is also discussed.展开更多
基金supported by the Directorate for Research and Community Service,University of Indonesia(RUUI Utama 2012),Jakarta,Indonesia
文摘The application of multi-hull ship or trimaran vessel as a mode of transports in both river and sea environments have grown rapidly in recent years.Trimaran vessels are currently of interest for many new high speed ship projects due to the high levels of hydrodynamic efficiency that can be achieved,compared to the mono-hull and catamaran hull forms.The purpose of this study is to identify the possible effects of using an unsymmetrical trimaran ship model with configuration(S/L) 0.1-0.3 and R/L=0.1-0.2.Unsymmetrical trimaran ship model with main dimensions: L=2000mm,B=200 mm and T=45 mm.Experimental methods(towing tank) were performed in the study using speed variations at Froude number 0.1-0.6.The ship model was pulled by an electric motor whose speed could be varied and adjusted.The ship model resistance was measured precisely by using a load cell transducer.The comparison of ship resistance for each configuration with mono-hull was shown on the graph as a function of the total resistance coefficient and Froude number.The test results found that the effective drag reduction could be achieved up to 17% at Fr=0.35 with configuration S/L=0.1.
基金Key Project funded by Department of Science & Technology of Heilongjiang Province (GB03A507)
文摘The research on underwater ship-hull cleaning robot was conducted on the purpose of realizing the automation of cleaning underwater ship hull so that service life of ship will be prolonged and ship speed will raised. Moreover, fuel consumption and the work intensity of divers will be reduced. In this paper, the current situation and the latest technology in China and abroad were analyzed;meanwhile, the typical characteristics of the underwater cleaning robot were introduced. According to the work principle of the underwater cleaning robot, the emphasis was put on the analysis and study of permanent-magnetic absorption, magnetic wheel, airproof and anticorrosion, underwater cleaning equipment and control system. The robot is easy in rotation and simple in control.
基金Supported by the Ministry of Education, Science, Sports, and Culture, Grant-in-aid for Scientific Research (A), (23246150), 2011
文摘Experimental investigations into the collapse behavior of a box-shape hull girder subjected to extreme wave-induced loads are presented.The experiment was performed using a scaled model in a tank.In the middle of the scaled model,sacrificial specimens with circular pillar and trough shapes which respectively show different bending moment-displacement characteristics were mounted to compare the dynamic collapse characteristics of the hull girder in waves.The specimens were designed by using finite element(FE)-analysis.Prior to the tank tests,static four-point-bending tests were conducted to detect the load-carrying capacity of the hull girder.It was shown that the load-carrying capacity of a ship including reduction of the capacity after the ultimate strength can be reproduced experimentally by employing the trough type specimens.Tank tests using these specimens were performed under a focused wave in which the hull girder collapses under once and repetitive focused waves.It was shown from the multiple collapse tests that the increase rate of collapse becomes higher once the load-carrying capacity enters the reduction path while the increase rate is lower before reaching the ultimate strength.
基金Supported by the Project of Ministry of Education and Finance(No.200512)the Project of the State Key Laboratory of ocean engineering(GKZD010053-10)
文摘A new multi-level analysis method of introducing the super-element modeling method, derived from the multi-level analysis method first proposed by O. F. Hughes, has been proposed in this paper to solve the problem of high time cost in adopting a rational-based optimal design method for ship structural design. Furthermore,the method was verified by its effective application in optimization of the mid-ship section of a container ship. A full 3-D FEM model of a ship,suffering static and quasi-static loads, was used as the analyzing object for evaluating the structural performance of the mid-ship module, including static strength and buckling performance. Research results reveal that this new method could substantially reduce the computational cost of the rational-based optimization problem without decreasing its accuracy, which increases the feasibility and economic efficiency of using a rational-based optimal design method in ship structural design.
基金Foundation item: Supported by the National Science Foundation (CMMI-1026264 and EEC-1157094).
文摘This paper addresses the development and testing of a remotely controlled boat platform with an innovative air-ventilated hull. The application of air cavities on the underside of ship hulls is a promising means for reducing hydrodynamic drag and pollutant emissions and increasing marine transportation efficiency. Despite this concept's potential, design optimization and high-performance operation of novel air-cavity ships remain a challenging problem. Hull construction and sensor instrumentation of the model-scale air-cavity boat is described in the paper. The modular structure of the hull allows for easy modifications, and an electric propulsion unit enables self-propelled operation. The boat is controlled remotely via a radio transmission system. Results of initial tests are reported, including thrust, speed, and airflow rate in several loading conditions. The constructed platform can be used for optimizing air-cavity systems and testing other innovative hull designs. This system can be also developed into a high-performance unmanned boat.
文摘Methods used for digital ship design were studied and formed the basis of a proposed frame model suitable for ship construction modeling. Based on 3-D modeling software, a digital design system for hull structures was developed. Basic software systems for modeling, modifying, and assembly simulation were developed. The system has good compatibility, and models created by it can be saved in different 3-D file formats, and 2D engineering drawings can be output directly. The model can be modified dynamically, overcoming the necessity of repeated modifications during hull structural design. Through operations such as model construction, intervention inspection, and collision detection, problems can be identified and modified during the hull structural design stage. Technologies for centralized control of the system, database management, and 3-D digital design are integrated into this digital model in the preliminary design stage of shipbuilding.
文摘As a new type of hull form,trimaran has remarkable excellent performances and has drawn more and more attention.When the viscous CFD technology now available is applied to the research of resistance performance of trimaran,the spatial discretization would usually result in the grid error and uncertainty,and thus the considerable discrepancy between the numerical results and the experimental data.In order to ascertain how much the grid would affect the calculation,the grid convergence should be studied.A mathematical trimaran was chosen as an example,with the commercial code CFX for the simulation,VOF for surface treatment,and the grid study was carried out based on two different turbulence models.It was concluded that carrying out grid study is helpful in estimating the grid error and uncertainty,and indicating the direction of improving the credibility of the numerical calculation, and,in addition to grid errors and uncertainties,the turbulence modeling errors and uncertainties contribute to the simulation errors.
基金sponsored by the Directorate of Research and Community Services,University of Indonesia(Hibah PUPT-Tambahan UI 2015)
文摘Multihull ships are widely used for sea transportation, and those with four hulls are known as quadramarans. Hull position configurations of a quadramaran include the diamond, tetra, and slice. In general, multihull vessels traveling at high speeds have better hydrodynamic efficiency than monohull ships. This study aims to identify possible effects of various quadramaran hull position configurations on ship resistance for hull dimensions of 2 m length, 0.21 m breadth, and 0.045 m thickness. We conducted a towing test in which we varied the hull spacing and speed at Fr values between 0.08 and 0.62 and measured the total resistance using a load cell transducer. The experimental results reveal that the lowest total resistance was achieved with a diamond quadramaran configuration at Fr = 0.1-0.6 and an effective interference factor of up to 0.35 with S/L = 3/10 and R/L = 1/2 at Fr = 0.62.
基金Project(2006AA09Z235) supported by National High Technology Research and Development Program of ChinaProject(CX2009B003) supported by Hunan Provincial Innovation Foundation For Postgraduate,China
文摘The flexible transmission shaft and wheel propeller are combined as the kinetic source equipment, which realizes the nmlti-motion modes of the autonomous underwater vehicle (AUV) such as vectored thruster and wheeled movement. In order to study the interactional principle between the hull and the wheel propellers while the AUV navigating in water, the computational fluid dynamics (CFD) method is used to simulate numerically the unsteady viscous flow around AUV with propellers by using the Reynolds-averaged Navier-Stokes (RANS) equations, shear-stress transport (SST) k-w model and pressure with splitting of operators (PISO) algorithm based on sliding mesh. The hydrodynamic parameters of AUV with propellers such as resistance, pressure and velocity are got, which reflect well the real ambient flow field of AUV with propellers. Then, the semi-implicit method for pressure-linked equations (SIMPLE) algorithm is used to compute the steady viscous flow field of AUV hull and propellers, respectively. The computational results agree well with the experimental data, which shows that the numerical method has good accuracy in the prediction of hydrodynamic performance. The interaction between AUV hull and wheel propellers is predicted qualitatively and quantitatively by comparing the hydrodynamic parameters such as resistance, pressure and velocity with those from integral computation and partial computation of the viscous flow around AUV with propellers, which provides an effective reference to the shady on noise and vibration of AUV hull and propellers in real environment. It also provides technical support for the design of new AUVs.
文摘The hydrodynamic analysis of a new semi-small waterplane area twin hull (SWATH) suitable for various applications such as small and medium size passenger ferries is presented. This may be an attractive crossover configuration resulting from the merging of two classical shapes: a conventional SWATH and a fast catamaran. The final hull design exhibits a wedge-like waterline shape with the maximum beam at the stem; the hull ends with a very narrow entrance angle, has a prominent bulbous bow typical of SWATH vessels, and features full stern to arrange waterjet propellers. Our analysis aims to perform a preliminary assessment of the hydrodynamic performance of a hull with such a complex shape both in terms of resistance of the hull in calm water and seakeeping capability in regular head waves and compare the performance with that of a conventional SWATH. The analysis is performed using a boundary element method that was preliminarily validated on a conventional SWATH vessel.
文摘An experimental investigation is performed to assess the relation of interference performance on the total resistance of a pentamaran model advancing in calm water. For this motivation, the total drag of the ship is performed for several values of asymmetric outrigger configuration and hull separation, altering the Froude number in the range 0.3–0.9. Our results indicate that remarkable changes in resistance require notable changes in transverse distance values (hull separation) when wave interference may occur. In addition, there is no single configuration that consistently outperforms the other configurations across the entire speed range and the optimum interference factor -0.2 appears at a Froude number of 0.45 in S/L=0.33 with the outrigger outer position: asymmetric outboard for A3 configuration.
基金Supported by the National Nature Science Foundation of China under Grant No.51109020 the National Key Project for Basic Research“973”(2009CB320805)
文摘Small water-plane area twin-hull(SWATH) has drawn the attention of many researchers due to its good sea-keeping ability.In this paper,MMG's idea of separation was used to perform SWATH movement modeling and simulation;respectively the forces and moment of SWATH were divided into bare hull,propeller,rudder at the fluid hydrodynamics,etc.Wake coefficient at the propellers which reduces thrust coefficient,and rudder mutual interference forces among the hull and propeller,for the calculation of SWATH,were all considered.The fourth-order Runge-Kutta method of integration was used by solving differential equations,in order to get SWATH's movement states.As an example,a turning test at full speed and full starboard rudder of ‘Seagull' craft is shown.The simulation results show the SWATH's regular pattern and trend of motion.It verifies the correctness of the mathematical model of the turning movement.The SWATH's mathematical model is applied to marine simulator in order to train the pilots or seamen,or safety assessment for ocean engineering project.Lastly,the full mission navigation simulating system(FMNSS) was determined to be a successful virtual reality technology application sample in the field of navigation simulation.
基金marine research institute (MRC) of AUT for some financial support of this project
文摘This study presents a numerical method for optimizing hull form in calm water with respect to total drag which contains a viscous drag and a wave drag. The ITTC 1957 model-ship correlation line was used to predict frictional drag and the corrected linearized thin-ship theory was employed to estimate the wave drag The evolution strategy (ES) which is a member of the evolutionary algorithms (EAs) family obtains an optimum hull form by considering some design constraints. Standard Wigley hull is considered as an initial hull in optimization procedures for two test cases and new hull forms were achieved at Froude numbers 0.24, 0.316 and 0.408. In one case the ES technique was ran for the initial hull form, where the main dimensions were fixed and the only variables were the hull offsets. In the other case in addition to hull offsets, the raain dimensions were considered as variables that are optimized simultaneously. The numerical results of optimization procedure demonstrate that the optimized hull forms yield a reduction in total drag.
基金Supported by the Foundation of Multihull Ship Technology,Key Laboratory of Fundamental Science for National Defence under Grant No.002010260737
文摘In order to get some useful parameters for grid generation of catamaran, the CFD software FLUENT is used to investigate the main effects of grid generation on flow field calculation. The influences of some elements are investigated with a series of calculations in the present paper, and some alteratives are proposed. The proposed alteratives based on the analysis of the effects are used for a catamaran resistance calculation, comparisons of the calculated results with experimental data show good agreement. It shows that the research result of this paver is useful for the numerical calculation of catamaran.
文摘In the present analysis, several parameters used in a numerical simulation are investigated in an integrated study to obtain their influence on the process and results of this simulation. The parameters studied are element formulation, friction coefficient, and material model. Numerical simulations using the non-linear finite element method are conducted to produce virtual experimental data for several collision scenarios. Pattern and size damages caused by collision in a real accident case are assumed as real experimental data, and these are used to validate the method. The element model study performed indicates that the Belytschko-Tsay element formulation should be recommended for use in virtual experiments. It is recommended that the real value of the friction coefficient for materials involved is applied in simulations. For the study of the material model, the application of materials with high yield strength is recommended for use in the side hull structure.
文摘A combination of methods was developed that can determine hydrodynamic forces on a planing hull in steady motion.Firstly,a potential-based boundary-element method was used to calculate the hydrodynamic pressure,induced resistance and lift.Then the frictional resistance component was determined by the viscous boundary layer theory.Finally,a particular empirical technique was applied.to determine the region of upwash geometry and determine spray resistance.Case studies involving four models of Series 62 planing craft were run.These showed that the suggested method is efficient and capable,with results that are in good agreement with experimental measurements over a wide range of volumetric Froude numbers.
文摘Tension leg platform (TLP) has been one of the most favorite deep-water platform concepts for offshore oil and gas field exploration and development. As of now,a total of 24 TLPs have been installed worldwide with 3 more to be installed in the near future and 5 more under design. Most of these installations are in the Gulf of Mexico (GoM). Water depths for these TLP installations range from 150 m to 1 600 m. It is highly expected that China will have her first TLP designed,fabricated,and installed in the very near future. In order to satisfy the need for a unified hull structural design practice,this paper presents the design philosophy of a conventional TLP hull structure with emphases on critical structural components design and analysis methodologies.
基金financed by the Portuguese Foundation for Science and Technology (Fundao para a Ciência e Tecnologia), under contract SFRH/BD/65120/2009
文摘A geometrically similar scaling was made from small-scale specimen to full-scale stiffened panels and then their collapse behaviour is investigated. It is considered that the stiffened panel compressive ultimate strength test was designed according to geometrical scaling laws so that the output of the test could be used as representative of the stiffened panels of the compressive zone of a tanker hull subjected to vertical bending moment. The ultimate strength of a tanker hull is analysed by a FE analysis using the experimentally developed master stress-strain curves which are obtained by the beam tension test and the compressive test of the stiffened panel, and are then compared with the result achieved by the progressive collapse method.
文摘A method of reliability analysis based on a direct strength calculation employing the von Mises stress failure criterion is presented here. The short term strain distributions of ship hull structural components are identified through the statistical analysis of the wave-induced strain history and the long term distributions by the weighted summation of the short term strain distributions. The wave-induced long term strain distribution is combined with the still water strain. The extreme strain distribution of the response strain is obtained by statistical analysis of the combined strains. The limit state function of the reliability analysis is based on the von Mises stress failure criterion, including the related uncertainties due to the quality of the material and model uncertainty. The reliability index is calculated using FORM and sensitivity analysis of each variable that has effects on the reliability is also discussed.