“进水”对电梯的危害及防范对策

电梯在使用过程中,常常会有"进水"的事情发生,较轻时使电梯外观不雅,严重时造成电梯损坏,有时甚至发生人身伤亡事故。因此,我们对电梯"进水"现象要引起足够重视,研究电梯"进水"危害的原因,探讨防范电梯"进水"的措施。本文通过多年检验经历,对"进水"的电梯进行检验,并进行这方面的初步探讨。

Comparative study of two biological nitrogen removal processes:A/O process and step-feeding process

Two biological nitrogen removal processes are compared in the aspect of nitrogen removal, process operation and energy saving. Results show that when the returned sludge ratio is 50% of the inflow rate, the step-feeding process achieves over 80% total nitrogen （TN） removal efficiency, but the TN removal efficiency of the A/O process is only 40%. Moreover, filamentous sludge bulking can be well restrained in the step-feeding process. Given the conditions of a returned sludge ratio of 100% and a nitrifying liquor recycle ratio of 200%, the TN removal efficiency is 78.32% in the A/O process, but the sludge volume index （SVI） value increases to 143 mL/g. In the step-feeding process, the SVI is only 94.4 mL/g when the TN removal efficiency reaches 81. 1%. The step-feeding process has distinct advantages over the A/O process in the aspects of practicability, nitrogen removal and operating stability.

Segmental Duplications Are Common in Rice Genome

Segmental duplications on rice (Oryza sativa L.) chromosomes 8, 9, 11, and 12 were studied by examining the distributions of sequences resolved by 13 probes detecting multiple copies of DNA sequences. Four of the hybridization bands detected by a repetitive sequence probe, rTRS, were mapped to the ends of all the four chromosomes. Two or three of the bands detected by each of the other 12 probes were also mapped to different chromosomes. The bands detected by the same probe usually occurred in similar locations of different chromosomes. Loci detected by different DNA probes were often similarly arranged on different chromosomes. Chromosomes 8 and 9 showed colinearity of marker loci arrangement indicating a possible common origin. A segment on chromosome 9 was also very similar to the previously reported duplicated fragments on the ends of chromosomes 11 and 12 which were also detected in this study, indicating a likely common origin. Moreover, the various degrees of distributional similarity of the segments suggest a complex relationship among the chromosomes in the evolution of the rice genome. These results support the proposition that chromosome duplication and diversification may be a mechanism for the origin and evolution of the chromosomes in the rice genome.

Laser Measurement and Intensity Evaluation of Intake Swirl in Engine Using a Water Analog

The intake swirl in the cylinder was induced by a swirler which was fixed in one of two intake ports. In order to understand the characteristics of the intake swirl, a transparent water analog was designed which simulated 150 type single cylinder engine. At the same time, the particle image velocimetry was used to measure the flow fields induced by various swirlers in the analog. After measurement, a new method was presented to evaluate the intensity of the intake swirl. Then, when the measured sections, the lifts of valve and the swirlers were different, the calculated results of the flow field were compared.

Research Progress of Evaluation Index of Soil Moisture

In modern agriculture, accurate and effective measurements of soil water content lays foundation for promotion on precision irrigation technology and improvement on water use efficiency. The research reviewed soil moisture indices at home and abroad and classified the indices into two categories in order to make prediction on soil moisture and take measures. Specifically, single indices included precipitation index, soil moisture index, and crop drought index and overall indices included supply/demand water index of crops, overall water index, PDSI, crop water shortage index. Soil moisture index was analyzed in terms of advantages and disadvantages,as well as adaptability in agriculture, providing references for relieving and predicting adverse effects on agriculture and formulating scientific policies.

Progress of Genetic Research on Grain Shape in Rice

Grain character is an important factor in yield components of rice. Progress of genetic research on grain length, grain width, lengthwidth ratio, grain thickness and grain weight were reviewed. It＇s considered that the genetic research on grain shape in rice has achieved considerable progress by exploration on genetic research for many years, but there are still some aspects waiting to be strengthened such as the grain shape, the genetic mechanism of grain shape and the genetic and potential value of grain shape in characteristic germplasm resources, etc.

Application of Computer Simulation in the Reservoir Flood Control

[Objective] To discuss the application of simulation technique in preliminary solution of reservoir flood control of.[Method] Based on the study of river system simulation theory,the InfoWorks RS system was adopted to build a digital analog model for flood routing in certain river system and the flood discharge was analyzed with the check criterion.[Result] The flood information system based on InfoWorks RS simulated the inundation of downstream during flood discharge and drew mutation pictures to indicate how hydraulic parameters of maximum runoff at each control section,runoff of each control section and flow velocity varied with time,how hydraulic elements mutated with time as well as the most likely inundated area analysis of lower reservoir.[Conclusion] To provide references for reducing serious loss caused by flood and making out preliminary solution to flood control.

Preliminary Study on the Extraction of Crude Toxin of Rhizoctonia solani and Its Activity

[ Objective] This study was to investigate the pathogenic mechanism of rice sheath blight pathogen （ Rhizoctonia solani） and the bioactive components of toxin. [ Method ] Rice sheath blight pathogen was cultured in the improved Richared medium; the culture filtrate was centrifuged and sterilized, then treated by activated carbon adsorption chromatography, distilled with methanol or water, and all were next concentrated, yielding the crude extracts of culture solution, crude extracts of methanol and crude extracts of water; the activities of these three extracts were determined, [ Result] The three extracts were russet pastes; activity determination showed that they had remarkable inhibitory effects on the growth of rice radicle and plantule, as well as the growth of four-foliage-young seedlings. They could also generate toxic effects on abscisic foliages and spots similar to the symptoms of sheath blight pathogen. [ Conclusion] Bioactive components of rice sheath blight pathogen toxin may be composed of various ingredients.

Development and Experimental Evaluation of a Steady-state Model for the Step-feed Biological Nitrogen Removal Process

In this article,a steady-state mathematical model was developed and experimentally evaluated to inves- tigate the effect of influent flow distribution and volume ratios of anoxic and aerobic zones in each stage on the to- tal nitrogen concentration of the effluent in the step-feed biological nitrogen removal process.Unlike the previous modeling methods,this model can be used to calculate the removal rates of ammonia and nitrate in each stage and thereby predict the concentrations of ammonia,nitrate,and total nitrogen in the effluent.To verify the simulation results,pilot-scale experimental studies were carried out in a four-stage step feed process.Good correlations were achieved between the measured data and the simulation results,which proved the validity of the developed model. The sensitivity of the model predictions was analyzed.After verification of the validity,the step feed process was optimally operated for five months using the model and the criteria developed for the design and operation.During the pilot-scale experimental period,the effluent total nitrogen concentrations were all below 5mg·L -1 ,with more than 90%removal efficiency.

Biological Nutrient Removal in a Full Scale Anoxic/Anaerobic/Aerobic/ Pre-anoxic-MBR Plant for Low C/N Ratio Municipal Wastewater Treatment

A novel full scale modified A2O （anoxic/anaerobic/aerobic/pre-anoxic）-membrane bioreactor （MBR） plant combined with the step feed strategy was operated to improve the biological nutrient removal （BNR） from low C/N ratio municipal wastewater in Southern China. Transformation of organic carbon, nitrogen and phosphorus, and membrane fouling were investigated. Experimental results for over four months demonstrated good efficiencies for chemical oxygen demand （COD） and NH4^＋-N removal, with average values higher than 84.5%and 98.1%, re-spectively. A relatively higher total nitrogen （TN） removal efficiency （52.1%） was also obtained at low C/N ratio of 3.82, contributed by the configuration modification （anoxic zone before anaerobic zone） and the step feed with a distribution ratio of 1：1. Addition of sodium acetate into the anoxic zone as the external carbon source, with a theoretical amount of 31.3 mg COD per liter in influent, enhanced denitrification and the TN removal efficiency in-creased to 74.9%. Moreover, the total phosphate （TP） removal efficiency increased by 18.0%. It is suggested that the external carbon source is needed to improve the BNR performance in treating low C/N ratio municipal waste-water in the modified A^2O-MBR process.

Performance evaluation of a modified step-feed anaerobic/anoxic/oxic process for organic and nutrient removal

A pilot scale modified step-feed process was lmproved to increase nutrient/N ano P） ano organic removal operations from municipal wastewater. It combined the step-feed process and a method named ＂University of Cape Town （UCT）＂. The effect of nutrient ratios and inflow distribution ratios were studied. The highest uptake efficiency of 95% for chemical oxygen demand （COD） has been achieved at the inflow distribution ratio of 40/35/25. However, maximum removal efficiency obtained for total nitrogen （TN） and phosphorus at 93% and 78%, respectively. The average mixed liquor suspended solids （MLSS） was 5500 mg·L- 1. In addition, convenient values for dissolved oxygen （DO） concentration, and pH were obtained throughout different stages. The proposed system was identified to be an appropriate enhanced biological nutrient removal process for wastewater treatment plants owing to relatively high nutrient removal, sturdy sludge settle ability and COD removal.

Exploring heating performance of gas engine heat pump with heat recovery

In order to evaluate the heating performance of gas engine heat pump（GEHP） for air-conditioning and hot water supply, a test facility was developed and experiments were performed over a wide range of engine speed（1400-2600 r/min）, ambient air temperature（2.4-17.8 ℃） and condenser water inlet temperature（30-50℃）. The results show that as engine speed increases from 1400 r/min to 2600 r/min, the total heating capacity and energy consumption increase by about 30% and 89%, respectively; while the heat pump coefficient of performance（COP） and system primary energy ratio（PER） decrease by 44% and 31%, respectively. With the increase of ambient air temperature from 2.4 ℃ to 17.8 ℃, the heat pump COP and system PER increase by 32% and 19%, respectively. Moreover, the heat pump COP and system PER decrease by 27% and 15%, respectively, when the condenser water inlet temperature changes from 30 ℃ to 50 ℃. So, it is obvious that the effect of engine speed on the performance is more significant than the effects of ambient air temperature and condenser water inlet temperature.

β-Cyclodextrin Promoted Oxidation of Cinnamaldehyde to Natural Benzaldehyde in Water

A facile and efficient procedure has been developed systematically for the oxidative cleavage of cinna-maldehyde to benzaldehyde by sodium hypochlorite with water as the only solvent in the presence of β-cyclodextrin （abbreviated as β-CD）. Different factors influencing cinnamaldehyde oxidation e.g. reaction temperature, the amount of catalyst and oxidant, have been investigated. The yield of benzaldehyde reaches 76% under the optimum conditions （333 K, 4 h, molar ratio of cinnamaldehyde to β-CD is 1：1）. Furthermore, a feasible reaction mecha-nism including the formation of benzaldehyde and the two main byproducts （phenylacetaldehyde and epoxide of cinnamaldehyde） has been proposed.

HPR1000： Advanced Pressurized Water Reactor with Active and Passive Safety

HPR1000 is an advanced nuclear power plant(NPP)with the significant feature of an active and passive safety design philosophy,developed by the China National Nuclear Corporation.On one hand,it is an evolutionary design based on proven technology of the existing pressurized water reactor NPP;on the other hand,it incorporates advanced design features including a 177-fuel-assembly core loaded with CF3 fuel assemblies,active and passive safety systems,comprehensive severe accident prevention and mitigation measures,enhanced protection against external events,and improved emergency response capability.Extensive verification experiments and tests have been performed for critical innovative improvements on passive systems,the reactor core,and the main equipment.The design of HPR1000fulfills the international utility requirements for advanced light water reactors and the latest nuclear safety requirements,and addresses the safety issues relevant to the Fukushima accident.Along with its outstanding safety and economy,HPR1000 provides an excellent and practicable solution for both domestic and international nuclear power markets.

In situ experimental study on TBM excavation with high-pressure water-jet-assisted rock breaking

China’s first high-pressure hydraulically coupled rock-breaking tunnel boring machine(TBM) was designed to overcome the rock breaking problems of TBM in super-hard rock geology, where high-pressure water jet system is configured, including high-flow pump sets, high-pressure rotary joint and high-pressure water jet injection device. In order to investigate the rock breaking performance of high-pressure water-jet-assisted TBM, in situ excavation tests were carried out at the Wan’anxi Water Diversion Project in Longyan, Fujian Province, China, under different water jet pressure and rotational speed. The rock-breaking performance of TBM was analyzed including penetration, cutterhead load, advance rate and field penetration index. The test results show that the adoption of high-pressure water-jet-assisted rock breaking technology can improve the boreability of rock mass, where the TBM penetration increases by 64% under the water jet pressure of 270 MPa. In addition, with the increase of the water jet pressure, the TBM penetration increases and the field penetration index decreases. The auxiliary rock-breaking effect of high-pressure water jet decreases with the increase of cutterhead rotational speed. In the case of the in situ tunneling test parameters of this study, the advance rate is the maximum when the pressure of the high-pressure water jet is 270 MPa and the cutterhead rotational speed is 6 r/min. The technical superiority of high-pressure water-jet-assisted rock breaking technology is highlighted and it provides guidance for the excavation parameter selection of high-pressure hydraulically coupled rock-breaking TBM.

Analysis and optimization of heat loss for water-cooled furnace roller

A heat transfer model of furnace roller cooling process was established based on analysis of furnace roller＇s structure. The complicated model was solved with iteration planning algorithm based on Newton search. The model is proved logical and credible by comparing calculated results and measured data. Then, the relationship between water flow velocity, inlet water temperature, furnace temperature and roller cross section temperature, outlet water temperature, water temperature rise, cooling water heat absorption was studied. The conclusions and recommendations are mainly as follows： l） Cooling water temperature rise decreases with the increase of water flow velocity, but it has small relationship with inlet water temperature; 2） In order to get little water scale, inlet water temperature should be controlled below 30 ℃. 3） The cooling water flow velocity should be greater than critical velocity. The critical velocity is 0.07 m/s and water flow velocity should be controlled within 0.4-0.8 m/s. Within this velocity range, water cooling efficiency is high and water temperature rise is little. If cooling water velocity increases again, heat loss will increase, leading to energy wasting.

Simulation of Hydrodynamic Performance of Drag and Double Reverse Propeller Podded Propulsors

The unsteady performance of drag and double reverse propeller podded propulsors in open water was numerically simulated using a computational fluid dynamics （CFD） method. A moving mesh method was used to more realistically simulate propulsor working conditions, and the thrust, torque, and lateral force coefficients of both propulsors were compared and analyzed. Forces acting on different parts of the propulsors along with the flow field distribution of steady and unsteady results at different advance coefficients were compared. Moreover, the change of the lateral force and the difference between the abovementioned two methods were mainly analyzed. It was shown that the thrust and torque results of both methods were similar, with the lateral force results having the highest deviation

Effect of water on extractive desulfurization of fuel oils using ionic liquids： A COSMO-RS and experimental study

When evaluating ionic liquids （ILs） for extractive desulfurization （EDS） of fuel oils, the inevitable presence of water in the system may have a significant and in many cases strongly negative effect. However, few studies have considered this particular issue and a promoted water effect on EDS is scarcely reported. In this work, COSMO-RS was firstly employed to calculate the capacity and selectivity for EDS of various IL/H20 mixtures, which cover different IL characters and a wide water concentration range. Experiments were then conducted with a representative IL [C4MIM]IH2P04], whose stable and even promoted extraction performance with a small amount of water was suggested by COSMO-RS. Through analyses of the desulfurization ratio, the cross- solubility and the water content in the desulfurized fuel, the promoted effect of water within a certain range （〈 10 wt%） was experimentally demonstrated. Moreover, such effect of water was explained combining the viscosity, the solvent-solute interactions and the COSMO-RS based analysis.

High Slope Stability of Diversion Power System Intake of Jinchuan Hydropower Station

The excavated height of the left bank slope of the diversion power system intake in Jinchuan hydropower station is about 16o m. The stability and safety of the slope during construction and its operation/utilization become one of the most important geological engineering problems. At the same time, it is also crucial to select a safe and economic excavation gradient for the construction. We studied the problem of how to select a safe and economic slope ratio by analyzing the geological condition of the high slope, including the lithology, slope structure, structural surface and their combinations, rock weathering and unloading, hydrology, and the natural gradient. The study results showed that the use of an excavation gradient larger than the gradient observed during site investigation and the gradient recommended in standards and field practice manuals is feasible. Then, we used the finite element method and rigid limit equilibrium method to evaluate the stability of the excavation slope under natural, rainstorm and earthquake conditions. The calculated results showed that the excavated slope only has limited failure, but its stability is greatly satisfactory. The research findings can be useful in excavation and slope stabilization projects.

Lake Mead Intake No. 3

As a result of a sustained drought in the Southwestern United States, and in order to maintain existing water capacity in the Las Vegas Valley, the Southern Nevada Water Authority constructed a new deep- water intake （Intake No. 3） located in Lake Mead. The project included a 185 m deep shaft, 4.7 km tunnel under very difficult geological conditions, and marine works for a submerged intake. This paper presents the experience that was gained during the design and construction and the innovative solutions that were developed to handle the difficult conditions that were encountered during tunneling with a dual- mode slurry tunnel-boring machine （TBM） in up to 15 bar （l bar = l0s Pa） pressure. Specific attention is given to the main challenges that were overcome during the TBM excavation, which included the mode of operation, face support pressures, pre-excavation grouting, and maintenance; to the construction of the intake, which involved deep underwater shaft excavation with blasting using shaped charges; to the construction of the innovative over 1200 t concrete-and-steel intake structure; to the placement of the intake structure in the underwater shaft; and to the docking and connection to an intake tunnel excavated by hybrid TBM.