钢轨“高点”缺陷分析与控制

钢轨通长方向上局部轨高异常偏高称为"高点"。"高点"严重影响高速列车的运行安全,是高速铁路用钢轨突出且难解决的质量缺陷。本文就重轨连轧过程中存在的"高点"问题进行了分析,认为轧件脱离轧辊时的瞬间"甩尾"是"高点"形成的根本原因。为止,提出并验证了控制连轧张力、调整出钢侧导板间隙、增加连轧轧制道次、优化头底延伸系数等减轻或消除"高点"的措施。上述方法中单机架完成钢轨成品道次轧制是可靠而稳定的方法,可使轨高"高点"稳定控制在0.2mm以下。

“高点”展上新地毯介绍

Shaw Living公司在“高点”地毯展上推出了Tommy Bahama许可品牌新地毯及“Cloud Nine”新品牌自行设计的新地毯。

U-E连轧失张对钢轨“高点”的影响分析

为了解决现场万能轧机与轧边机连轧60kg/m钢轨过程中距尾部3.6m处出现局部＂高点＂的问题,经试验与分析,对可能导致＂高点＂产生的第3道次轧制过程利用有限元仿真软件进行了仿真模拟,分析得出连轧失张产生的收缩力是导致局部＂高点＂产生的主要原因,最后从纵波和能量的角度提出了措施,解决了该问题。

微管壳式换热器在能量转换循环中的应用

目前,超临界二氧化碳(S-CO_(2))布雷顿循环普遍采用印刷电路板换热器(PCHE)来保证其相对其他能量转换循环的紧凑性优势。PCHE芯体为整体结构,若内部出现泄漏或结垢等问题,很难进行维护与检修。本文提出了一种微管壳式换热器(MSTE),其结构与传统管壳式换热器类似,但其管径缩小至微通道级。由于MSTE的流道横截面积占总截面积之比较PCHE大,在典型的回热器与冷却器设计工况下,相对PCHE而言,采用MSTE可将体积与质量均减小30%以上。灵敏性分析结果显示,采用本文设计的MSTE结构的回热器与冷却器,回热器冷热流道入口温度升高20℃左右,压缩机入口温度变化均不超过1℃,说明该种结构换热器的换热能力足够支撑能量转换循环的一般工况波动。

河南省城市社区卫生服务利用现状

目的了解河南省城市社区慢性病监测网络中高血压、糖尿病患者对社区卫生服务的利用情况。方法对河南省城市社区慢性病监测试点的高血压、糖尿病患者进行面对面问卷调查。结果1/3以上的高血压、糖尿病管理患者将社区作为知识获取的第一途径;对社区卫生服务基本满意率为92.9%;6个月内到社区就诊率平均为64.6%;86.0%的高血压患者和54.1%糖尿病患者能做到1月内定期测量血压和检测血糖;60%的管理患者选择社区就诊;80.03%以上的管理患者接受了药物性治疗,有56.7%～82.3%的管理患者接受了非药物性治疗服务。结论要积极推广社区高血压、糖尿病综合防控适宜技术,加强患者规范管理,提升社区卫生服务能力,促进居民对社区卫生服务的利用。

Genetic Diversity of Gli-1,Gli-2 and Glu-1 Alleles Among Chinese Endemic Wheats

Genetic diversity at Gli_1, Gli_2 and Glu_1 loci was investigated in 32 accessions of Chinese endemic wheat by using acid polyacrylamide gel electrophoresis (APAGE) and sodium dodecyl sulfate (SDS)_PAGE. There were 8 gliadin and 3 high_molecular_weight (HMW)_glutenin patterns in 14 Yunnan hulled wheat ( Triticum aestivum ssp. yunnanese King) accessions, 9 gliadin and 4 HMW_glutenin patterns in 9 Tibetan weedrace ( T. aestivum ssp. tibetanum Shao ) accessions, and 9 gliadin and 5 HMW_glutenin patterns in 9 Xinjiang rice wheat ( T. petropavlovskyi Udacz. et Migusch.) accessions. One accession (i.e. Daomai 2) carried new subunits 2.1+10.1 encoded by Glu_D1. Among the three Chinese endemic wheat groups, a total of 10, 14 and 11 alleles at Gli_1 locus; 11, 14 and 12 alleles at Gli_2 locus; and 5, 6 and 8 alleles at Glu_1 locus were identified, respectively. Among Yunnan hulled wheat, Tibetan weedrace and Xinjiang rice wheat, the Nei's genetic variation indexes were 0.3798, 0.5625 and 0.5693, respectively. These results suggested that Tibetan weedrace and Xinjiang rice wheat had higher genetic diversity than Yunnan hulled wheat.

Distribution characteristics and succession regulation of the forests in alpine and canyon region of western Sichuan Province, P.R.China

Since 1950, 700 plots were established in the alpine and canyon region of western Sichuan. The distribution charac-teristics and the relationships between forest succession and environmental gradients were studied. The results showed that the main tree species were Picea and Abies in this region, and there were more than 90 forest types. Abies forests mainly dis-tributed in the middle and upper reaches of rivers and their branches, and Picea forests mainly distributed in wide valleys and on half-shaded and half-sunny slopes. The natural regeneration was poor under primitive spruce and fir forest canopy, but was good in the spruce and fire forest gap. The relationship between forest succession and vertical gradient was closely related to the relationship between forest succession procession and plant synusia under primary forests. Human activities could promote and postpone succession process. The results of expanding regeneration were often influenced by topography, vegetation and wind direction.

Modified algorithm of combined GPS/GLONASS precise point positioning for applications in open-pit mines

A modified algorithm of combined GPS/GLONASS precise point positioning （GG-PPP） was developed by decreasing the number of unknowns to be estimated so that accurate position solutions can be achieved in the case of less number of visible satellites. The system time difference between GPS and GLONASS （STDGG） and zenith tropospheric delay （ZTD） values were firstly estimated in an open sky condition using the traditional GG-PPP algorithm. Then, they were used as a priori known values in the modified algorithm instead of estimating them as unknowns. The proposed algorithm was tested using observations collected at BJFS station in a simulated open-pit mine environment. The results show that the position filter converges much faster to a stable value in all three coordinate components using the modified algorithm than using the traditional algorithm. The modified algorithm achieves higher positioning accuracy as well. The accuracy improvement in the horizontal direction and vertical direction reaches 69% and 95% at a satellite elevation mask angle of 50°, respectively.

Hot deformation behavior of spray forming LSHR alloy using constitutive equation and processing map

Flow behaviors of spray forming low solvus high refractory (LSHR) alloy were investigated using hot compression tests performed on a Gleeble?3500 thermal mechanical simulator at temperatures of 1020?1150 °C and strain rates of 0.0003?1.0 s?1. The constitutive equation was established, power dissipation (η) maps and hot processing maps were plotted. The microstructure evolution and dislocation distribution of domains with different values of η in power dissipation maps were also observed. The results show that the flow stress increases with decreasing temperature and increasing strain rate. The activation energy of the spray forming LSHR alloy is 1243.86 kJ/mol. When the value of η is 0.36 at the strain of 0.5, the domain in the processing map shows characteristics of typical dynamic recrystallization (DRX) and low dislocation density. According to the microstructure evolution and processing maps, the optimum processing condition for good hot workability of spray forming LSHR alloy can be summed up as:temperature range 1110?1150 °C; strain rate range 0.01?0.3 s?1.

Segmentation of scattered point data through a new curvature analysis algorithm

A systematic scheme is proposed to automatically extract geometric surface features from a point cloud composed of a set of unorganized three-dimensional coordinate points by data segmentation. The key technology is a algorithm that estimates the local surface curvature properties of scattered point data based on local base surface parameterization. Eight surface types from the signs of the Gaussian and mean curvatures provide an initial segmentation, which will be refined by an iterative region growing method. Experimental results show the scheme's performance on two point clouds.

Dynamic Changes of Nitrate Reductase Activity within 24 Hours

[Objective] The research aimed to study the circadian rhythm of nitrate re- ductase activity （NRA） in plant. [Method] The wheat plants at heading stage were used as the materials for the measurement of dynamic changes of nitrate reductase activity （NRA） within 24 h under the conditions of constant high temperature. [Resulti The fluctuation of NRA in wheat changed greatly from 20：00 pm to 11：00 am. The enzyme activity remained constant, but at 14：00 the enzyme activity was the high- est, higher than all the other time points except the enzyme activity measured at11：00. The enzyme activity was the lowest of 17：00, which was lower than all the other time points except the enzyme activity measured at 2：00. [Conclusion] There were autonomous rhythm changes of NRA in wheat in a certain degree.

Opportunities and Challenges for Chinese Enterprises ──Viewpoints from Foreign Counterparts at Chinese Enterprises' Summit Meeting 2000

This paper is summarized from the speeches given by foreign entrepreneurs at Chinese Enterprises’ Summit Meeting 2000. In the paper, the entrepreneurs set forth the opportunities for Chinese enterprises and the existing problems from several aspects as globalization of China, influence of WTO, as well as financial reform and capital market opening, etc.

The Spectrum of High Rank Differential Operators of the C_0 Semigroups

In this paper,the author study the spectrum of high rank differential operators T (n) (t) of C 0 Semigroup T(t) ,given an approach to construct the spectral set opetator T (n) (t) ,and discussed the relation between the spectral points of both T (n) (t) and infinitesimal generator A of T(t) .

Volatile Organic Compound Emissions when Drying Wood Particles at High Dewpoints

Emission of volatile organic compounds (VOCs) during drying of wood particles for particleboard manufacture, or for production of refined biofuels, is a potential environmental problem. The aim of this work is to study the emissions of VOCs during drying, and the influence on the emissions by different drying parameters.The experiments have mainly been done in a batch fluidized bed dryer, but measurements have also been done in a, pilot scale, continuous fluidized bed dryer. The parameters studied are air flow rate through the bed, air temperature, air dewpoint, and bed height. Since the present trend in biofuels and particle drying is towards very high dewpoints during drying, some measurements have been made at dewpoints up to 95℃, corresponding to a water content of 3.2 kg water per kilogram dry air. The emissions have been measured in two different ways,online during drying with a flame ionization detector and through wood analyses of the terpene content in the wood particles before and after drying. Substantial work has been made in developing the latter method as well as developing the drying equipment to be able to produce a wide range of conditions of the drying medium. It was shown that the VOCs emitted, during wood particle drying, mainly consist of terpenes. The behavior of the emissions was typical, at first contact with the drying gas a sharp peak in the release rate was detected. After that,the release rate stabilizes and declines slowly to a point where the material temperature increases and results in a second small peak in the release rate. Typically 80%-90% of the initial terpene content in the material was emitted during drying to low moisture content and it is not possible to significantly influence this release by changing the drying conditions. Up to 50% of the emitted terpenes are released during a very short period after contact with the drying medium. This fact could be utilized by employing a 2-step drying process. The fact that the VOC concentration in the inert gas gets much higher when drying at higher dewpoints could be taken into consideration when dealing with closed loop applications where the inert gas after the dryer is burnt.

Wall Sticking of High Water-Cut, Highly Viscous and High Gel-Point Crude Oil Transported at Low Temperatures

Some crude oils with high water cut have the capability to flow below the oil gel point, while the oil particles adhere to the pipe wall in the form of paste, also called "wall sticking". Wall sticking is a serious problem during the pipeline transportation, leading to partial or total blockage of the pipeline and energy wastage. In this paper, a series of laboratory flow loop experiments were conducted to observe the wall sticking characteristics of crude oil with high water cut, high viscosity and high gel point at low transportation temperatures. The effects of shear stress and water cut on the wall sticking rate and occurrence temperature were investigated. Experimental results indicated that the wall sticking rate and occurrence temperature were lower under stronger shear stress and higher water cut conditions. A criterion of wall sticking occurrence temperature(WSOT) and a regression model of wall sticking rate were then established. Finally, the software was developed to calculate the pressure drop along the pipelines of crude oils with high water-cut. It was able to predict the wall sticking thickness of gelled oil and then calculate the pressure drop along the pipelines. A typical case study indicated that the prediction results obtained from the software were in agreement with actual measured values.

胶州湾北部软底大型底栖动物丰度和生物量的研究

1995年3～11月对胶州湾北部软底海域进行了 两月一次的大型底栖动物调查。调查期间，大型底栖动物总平均丰度和总平均生物量分别为 1891.3 inds./m2和41.9 g.w.w/m2。与该海域有关大型底栖动物丰度和生物量的历史 资料相比较，本研究所得到的大型底栖动物丰度值显著增加，生物量值则有较明显的下降， 初步分析了发生这些变化主要原因。丰度和生物量比较曲线表明，所研究海域底栖生物群落 处于中等干扰(即污染的影响 )状态。

Locating method of fire source for spontaneous combustion of sulfide ores

in order to achieve a more efficient way to accurately detect the position of the fire source of spontaneous combustion underground mine, a simple fire source locating method, based on infrared scanning system which can determine the point where the highest temperature on the surface of igniting ores occurs, was proposed. First, the differential equations that describe heat flow in ore body were presented and the relationship between the surface temperature distribution and the depth and intensity of inner fire source was established with a relatively simple heat transfer model. With the solution of equation, the expression of the relationship between the surface temperature distribution and the inner fire source was deduced and the mathematical-physical model of heat transfer process was set up. Then, with the model, visualization of fire source on the basis of MATLAB simulation platform was realized. The results show that： 1） within 10 m, when the detecting depth is less than 2 m, the temperature perturbation on ores surface can change rapidly, and then slowly; after 4 m, in contrast, it changes very little, and is even close to zero at 10 m; 2） When it is close to self-ignition duration and the detective depths are 2, 5 and 10 m, respectively, the maximum temperature differences are correspondingly 0.5, 0.04 and 0.005 ℃ in the scope of 1 m×1 m; under the same condition, the maximum temperature differences are 1.391, 0.136 and 0.018 ℃, respectively, in the scope of 2 m×2 m. Therefore, this system can be used to measure the temperature differences on the surface of ore body and determine the highest temperature point directly. Also, it is possible to determine the depth of fire source and its intensity by locating method of fire source indirectly.

Research on the Algorithm of Extracting Ridgeand Valley Lines from Contour Data

In this paper, the authors put forward a brief and practical arithmetic for auto extracting terrain lines from digital terrain data after analyzing and comparing current arithmetics.This paper gives an experiment result that the ridge and valley extracted by the arithmetic is consistent with the experimental terrain.

Influence of Late Springtime Surface Sensible Heat Flux Anomalies over the Tibetan and Iranian Plateaus on the Location of the South Asian High in Early Summer

Variation in the location of the South Asian High （SAH） in early boreal summer is strongly influenced by elevated surface heating from the Tibetan Plateau （TP） and the Iranian Plateau （IP）. Based on observational and ERA-Interim data, diagnostic analyses reveal that the interannual northwestward-southeastwaxd （NW-SE） shift of the SAH in June is more closely correlated with the synergistic effect of concurrent surface thermal anomalies over the TP and IP than with each single surface thermal anomaly over either plateau from the preceding May. Concurrent surface thermal anomalies over these two plateaus in May are characterized by a negative correlation between sensible heat flux over most parts of the TP （TPSH） and IP （IPSH）. This anomaly pattern can persist till June and influences the NW-SE shift of the SAH in June through the release of latent heat （LH） over northeastern India. When the IPSH is stronger （weaker） and the TPSH is weaker （stronger） than normal in May, an anomalous cyclone （anticyclone） appears over northern India at 850 hPa, which is accompanied by the ascent （descent） of air and anomalous convergence （divergence） of moisture flux in May and June. Therefore, the LH release over northeastern India is strengthened （weakened） and the vertical gradient of apparent heat source is decreased （increased） in the upper troposphere, which is responsible for the northwestward （southeastward） shift of the SAH in June.

Low Power Single-Chip RF Transceiver for Human Body Cormunication

Human body communication is proposed as a promising body proximal comanunication tech- nology for body sensor networks. To achieve low power and slmll volume ill the sensor nodes, a Ra-dio Frequency （RF） application-specific integrated circuit transceiver tbr Human Body Commnunication （HBC） is presented and the characteristics of HBC are investigated. A high data rate On-Off Keying （OOK）/Frequency-Shift Keying （FSK） modulation protocol and an OOK/FSK delrodulator circuit are introduced in this paper, with a data-rate-to-carrier-frequency ratio up to 70%. A low noise amplifier is proposed to handle the dynamic range problem and improve the sensitivity of the receiver path. In addi-tion, a low power autonmatic-gain-control system is realized using a novel architecture, thereby render-ing the peak detector circuit and loop filter unneces-sary. Finally, the complete chip is fabricated. Simula-tion results suggest receiver sensitivity to be-75 dBm. The transceiver shows an overall power con-smxption of 32 mW when data rate is 5 Mbps, de-livering a P1dB output power of - 30 dBm.