Synergistic anionic/zwitterionic mixed surfactant system with high emulsification efficiency for enhanced oil recovery in low permeability reservoirs

Emulsification is one of the important mechanisms of surfactant flooding. To improve oil recovery for low permeability reservoirs, a highly efficient emulsification oil flooding system consisting of anionic surfactant sodium alkyl glucosyl hydroxypropyl sulfonate(APGSHS) and zwitterionic surfactant octadecyl betaine(BS-18) is proposed. The performance of APGSHS/BS-18 mixed surfactant system was evaluated in terms of interfacial tension, emulsification capability, emulsion size and distribution, wettability alteration, temperature-resistance and salt-resistance. The emulsification speed was used to evaluate the emulsification ability of surfactant systems, and the results show that mixed surfactant systems can completely emulsify the crude oil into emulsions droplets even under low energy conditions. Meanwhile,the system exhibits good temperature and salt resistance. Finally, the best oil recovery of 25.45% is achieved for low permeability core by the mixed surfactant system with a total concentration of 0.3 wt%while the molar ratio of APGSHS:BS-18 is 4:6. The current study indicates that the anionic/zwitterionic mixed surfactant system can improve the oil flooding efficiency and is potential candidate for application in low permeability reservoirs.

Study on Skin Care Efficacy of the Active Ingredients in Camellia Japonica Flowers at High and Low Altitudes

The active ingredients of Camellia japonica flowers(CJF)at high and low altitudes,as well as their skin care efficacy were compared.The dried red CJF at high and low altitudes were ultrasonically extracted with 70%ethanol,and these extracts were concentrated and then diluted to a constant volume.The content of total flavonoids,total polyphenols and total proteins was tested and analyzed.In addition,DPPH free radical scavenging,inhibition of the formation of advanced glycation end products,and inhibitory activity against elastase was measured to compare their skin care efficacy in anti-oxidation,anti-glycation,anti-wrinkling and firming.The results showed that,based on the dry weight of CJF,the content of total flavonoids and total proteins of the CJF at high altitude was approximately 1.5 times of the CJF at low altitude,while the content of total polyphenols was approximately 2.4 times that of the CJF at low altitude.The skin care efficacy of CJF at high altitude was significantly better than that of the CJF at low altitude.This work could provide theoretical basis for the selection and application of Camellia japonica flowers in the field of cosmetics.

Noncovalent cross-linked engineering hydrogel with low hysteresis and high sensitivity for flexible self-powered electronics

In this study,the hydrogel network was reinforced by covalent-like hydrogen bonding,and the strong binding ability of boron-nitrogen coordination served as the main driving force.Among them,acrylamide(AM)and 3-acrylamidophenylboronic acid(AAPBA)were the main body,and the numerous hydroxyl groups in the trehalose(Treh)molecule and other polymer groups formed strong hydrogen bonding interactions to improve the mechanical properties of the PAM/PAAPBA/Treh(PAAT)hydrogel and ensured the simplicity of the synthesis process.The hydrogel possessed high strain at break(1239%),stress(64.7 kPa),low hysteresis(100%to 500%strain,corresponding to dissipation energy from 1.37 to 7.80 kJ/m^(3)),and outstanding cycling stability(retained more than 90%of maximum stress after 200 ten-sile cycles).By integrating carbon nanotubes(CNTs)into PAAT hydrogel(PAATC),the PAATC hydrogel with excellent strain response performance was successfully constructed.The PAATC conductive hydro-gel exhibited high sensitivity(gauge factor(GF)=10.58 and sensitivity(S)=0.304 kPa^(-1)),wide strain response range(0.5%-1000%),fast response time(450 ms),and short recovery time(350 ms),excellent fatigue resistance,and strain response stability.Furthermore,the PAATC-based triboelectric nanogener-ator(TENG)displayed outstanding energy harvesting performance,which shows its potential for appli-cation in self-powered electronic devices.

Low skeletal muscle mass and high visceral adiposity are associated with recurrence of acute cholecystitis after conservative management:A propensity score-matched cohort study

Background:Recurrent acute cholecystitis(RAC)can occur after non-surgical treatment for acute cholecystitis(AC),and can be more severe in comparison to the first episode of AC.Low skeletal muscle mass or adiposity have various effects in several diseases.We aimed to clarify the relationship between RAC and body parameters.Methods:Patients with AC who were treated at our hospital between January 2011 and March 2022 were enrolled.The psoas muscle mass and adipose tissue area at the third lumbar level were measured using computed tomography at the first episode of AC.The areas were divided by height to obtain the psoas muscle mass index(PMI)and subcutaneous/visceral adipose tissue index(SATI/VATI).According to median VATI,SATI and PMI values by sex,patients were divided into the high and low PMI groups.We performed propensity score matching to eliminate the baseline differences between the high PMI and low PMI groups and analyzed the cumulative incidence and predictors of RAC.Results:The entire cohort was divided into the high PMI(n=81)and low PMI(n=80)groups.In the propensity score-matched cohort there were 57 patients in each group.In Kaplan-Meier analysis,the low PMI group and the high VATI group had a significantly higher cumulative incidence of RAC than their counterparts(log-rank P=0.001 and 0.015,respectively).In a multivariate Cox regression analysis,the hazard ratios of low PMI and low VATI for RAC were 5.250(95%confidence interval 1.083-25.450,P=0.039)and 0.158(95%confidence interval:0.026-0.937,P=0.042),respectively.Conclusions:Low skeletal muscle mass and high visceral adiposity were independent risk factors for RAC.

Highly Differentiated Target Detection under Extremely Low-Light Conditions Based on Improved YOLOX Model

This paper expounds upon a novel target detection methodology distinguished by its elevated discriminatory efficacy,specifically tailored for environments characterized by markedly low luminance levels.Conventional methodologies struggle with the challenges posed by luminosity fluctuations,especially in settings characterized by diminished radiance,further exacerbated by the utilization of suboptimal imaging instrumentation.The envisioned approach mandates a departure from the conventional YOLOX model,which exhibits inadequacies in mitigating these challenges.To enhance the efficacy of this approach in low-light conditions,the dehazing algorithm undergoes refinement,effecting a discerning regulation of the transmission rate at the pixel level,reducing it to values below 0.5,thereby resulting in an augmentation of image contrast.Subsequently,the coiflet wavelet transform is employed to discern and isolate high-discriminatory attributes by dismantling low-frequency image attributes and extracting high-frequency attributes across divergent axes.The utilization of CycleGAN serves to elevate the features of low-light imagery across an array of stylistic variances.Advanced computational methodologies are then employed to amalgamate and conflate intricate attributes originating from images characterized by distinct stylistic orientations,thereby augmenting the model’s erudition potential.Empirical validation conducted on the PASCAL VOC and MS COCO 2017 datasets substantiates pronounced advancements.The refined low-light enhancement algorithm yields a discernible 5.9%augmentation in the target detection evaluation index when compared to the original imagery.Mean Average Precision(mAP)undergoes enhancements of 9.45%and 0.052%in low-light visual renditions relative to conventional YOLOX outcomes.The envisaged approach presents a myriad of advantages over prevailing benchmark methodologies in the realm of target detection within environments marked by an acute scarcity of luminosity.

Enhanced reversible hydrogen storage properties of wrinkled graphene microflowers confined LiBH_(4) system with high volumetric hydrogen storage capacity

LiBH_(4)with high hydrogen storage density,is regarded as one of the most promising hydrogen storage materials.Nevertheless,it suffers from high dehydrogenation temperature and poor reversibility for practical use.Nanoconfinement is effective in achieving low dehydrogenation temperature and favorable reversibility.Besides,graphene can serve as supporting materials for LiBH_(4)catalysts and also destabilize LiBH_(4)via interfacial reaction.However,graphene has never been used alone as a frame material for nanoconfining LiBH_(4).In this study,graphene microflowers with large pore volumes were prepared and used as nanoconfinement framework material for LiBH_(4),and the nanoconfinement effect of graphene was revealed.After loading 70 wt%of LiBH_(4) and mechanically compressed at 350 MPa,8.0 wt% of H2 can be released within 100 min at 320C,corresponding to the highest volumetric hydrogen storage density of 94.9 g H2 L^(-1)ever reported.Thanks to the nanoconfinement of graphene,the rate-limiting step of dehydrogenation of nanoconfined LiBH_(4) was changed and its apparent activation energy of the dehydrogenation(107.3 kJ mol^(-1))was 42%lower than that of pure LiBH_(4).Moreover,the formation of the intermediate Li_(2)B_(12)H_(12) was effectively inhibited,and the stable nanoconfined structure enhanced the reversibility of LiBH_(4).This work widens the understanding of graphene's nanoconfinement effect and provides new insights for developing high-density hydrogen storage materials.

A novel profile modification HPF-Co gel satisfied with fractured low permeability reservoirs in high temperature and high salinity

Conformance control and water plugging are a widely used EOR method in mature oilfields.However,majority of conformance control and water plugging agents are unavoidable dehydrated situation in high-temperature and high-salinity low permeability reservoirs.Consequently,a novel conformance control system HPF-Co gel,based on high-temperature stabilizer(CoCl_(2)·H_(2)O,CCH)is developed.The HPF-Co bulk gel has better performances with high temperature(120℃)and high salinity(1×10^(5)mg/L).According to Sydansk coding system,the gel strength of HPF-Co with CCH is increased to code G.The dehydration rate of HPF-Co gel is 32.0%after aging for 150 d at 120℃,showing excellent thermal stability.The rheological properties of HPF gel and HPF-Co gel are also studied.The results show that the storage modulus(G′)of HPF-Co gel is always greater than that of HPF gel.The effect of CCH on the microstructure of the gel is studied.The results show that the HPF-Co gel with CCH has a denser gel network,and the diameter of the three-dimensional network skeleton is 1.5-3.5μm.After 90 d of aging,HPF-Co gel still has a good three-dimensional structure.Infrared spectroscopy results show that CCH forms coordination bonds with N and O atoms in the gel amide group,which can suppress the vibration of cross-linked sites and improve the stability at high temperature.Fractured core plugging test determines the optimized polymer gel injection strategy and injection velocity with HPF-Co bulk gel system,plugging rate exceeding 98%.Moreover,the results of subsequent waterflooding recovery can be improved by 17%.

Analysis of the Flow Field and Impact Force in High-Pressure Water Descaling

This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by means of a fluid–structure interaction(FSI)method by which the descaling effect produced by rolling coils with different section sizes is examined.Assuming a flat fan-shaped nozzle at the entrance of the R1R2 roughing mill,the outflow field characteristics and the velocity distribution curve on the strike line(at a target distance of 30–120 mm)are determined.It is found that the velocity in the center region of the water jet with different target distances is higher than that in the boundary region.As the target distance increases,the velocity of the water jet in the central region decreases.Through comparison with experimental results,it is shown that the simulation model can accurately predict the impact position of the high-pressure water on the impact plate,thereby providing a computational scheme that can be used to optimize the nozzle space layout and improve the slabs’descent effect for different rolling specifications.

Effect of slow shot speed on externally solidified crystal,porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy

The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).

The environmental analysis and site selection of mussel and large yellow croaker aquaculture areas based on high resolution remote sensing

Mussel aquaculture and large yellow croaker aquaculture areas and their environmental characteristics in Zhoushan were analyzed using satellite data and in-situ surveys.A new two-step remote sensing method was proposed and applied to determine the basic environmental characteristics of the best mussel and large yellow croaker aquaculture areas.This methodology includes the first step of extraction of the location distribution and the second step of the extraction of internal environmental factors.The fishery ranching index(FRI1,FRI2)was established to extract the mussel and the large yellow croaker aquaculture area in Zhoushan,using Gaofen-1(GF-1)and Gaofen-6(GF-6)satellite data with a special resolution of 2 m.In the second step,the environmental factors such as sea surface temperature(SST),chlorophyll a(Chl-a)concentration,current and tide,suspended sediment concentration(SSC)in mussel aquaculture area and large yellow croaker aquaculture area were extracted and analyzed in detail.The results show the following three points.(1)For the extraction of the mussel aquaculture area,FRI1 and FRI2 are complementary,and the combination of FRI1 and FRI2 is suitable to extract the mussel aquaculture area.As for the large yellow croaker aquaculture area extraction,FRI2 is suitable.(2)Mussel aquaculture and the large yellow croaker aquaculture area in Zhoushan are mainly located on the side near the islands that are away from the eastern open waters.The water environment factor template suitable for mussel and large yellow croaker aquaculture was determined.(3)This two-step remote sensing method can be used for the preliminary screening of potential site selection for the mussels and large yellow croaker aquaculture area in the future.the fishery ranching index(FRI1,FRI2)in this paper can be applied to extract the mussel and large yellow croaker aquaculture areas in coastal waters around the world.

Prediction of Low Heating Value of Sugar Cane Bagasse as a Fuel for Industrial Boilers in the High Relative Humidity Region: Case of Cameroon

Many attempts have been made to estimate calorific value of bagasse using mathematical equations, which were created based on data from proximate, ultimate, physical and chemical analysis. Questions have been raised on the applicability of these equations in different parts of the globe. This study was initiated to tackle these problems and also check the most suited mathematical models for the Law Heating Value of Cameroonian bagasse. Data and bagasse samples were collected at the Cameroonian sugarcane factory. The effects of cane variety, age of harvesting, source, moisture content, and sucrose on the LHV of Cameroon bagasse have been tested. It was shown that humidity does not change within a variety, but changes from the dry season to the rainy season;the sugar in the rainy season is significantly different from that collected in the dry season. Samples of the same variety have identical LHV. LHV in the dry season is significantly different from LHV in the rainy season. According to the fact that this study was done for cane with different ages of harvesting, the maturity of Cameroonian sugarcane does not affect LHV of bagasse. Tree selected models are much superior tool for the prediction of the LHV for bagasse in Cameroon compared to others. The standard deviation of these validated models is around 200 kJ/kg compared to the experimental. Thus, the models determined in foreign countries, are not necessarily applicable in predicting the LHV of bagasse in other countries with the same accuracy as that in their native country. There was linear relationship between humidity, ash and sugar content in the bagasse. It is possible to build models based on data from physical composition of bagasse using regression analysis.

Determination of critical state line(CSL)for silty-sandy iron ore tailings subjected to low-high confining pressures

The disposal of filtered tailings in high dry stacks can induce particle breakage,changing the material's behaviour during the structure's lifetime.The grading changes influence material properties at the critical state,and this is not mature for intermediate artificial soils(tailings)in a broad range of confining pressures.In this paper,it aims to describe the behaviour of iron ore tailings in a spectrum of confining pressures broader than the reported in previous studies.A series of consolidated drained(CD)triaxial tests was carried out with confining pressures ranging from 0.075 MPa to 120 MPa.These results show that the amount of breakage plays an essential role in the response of iron ore tailings.The existence of curved critical state line(CSL)in both specific volume(ν)-logarithm of mean effective stress(p′)and deviatoric stress(q)-mean effective stress(p′)planes,and different responses in the deviatoric stress-axial strain-volumetric strain curves were verified.An inverse S-shaped equation was proposed to represent the silty-sandy tailings'behaviour up to high pressures onν-lnp′plane.The proposed equation provides a basis for enhancing constitutive models and considers the evolution of the grading up to severe loading conditions.The adjustment considered three regions with different responses associated with particle breakage at different pressure levels.

A study of pulsed high voltage driven hollow-cathode electron beam sources through synchronous optical trigger

In this study,a pulsed,high voltage driven hollow-cathode electron beam sources through an optical trigger is designed with characteristics of simple structure,low cost,and easy triggering.To validate the new design,the characteristics of hollow-cathode discharge and electron beam characterization under pulsed high voltage drive are studied experimentally and discussed by discharge characteristics and analyses of waveform details,respectively.The validation experiments indicate that the pulsed high voltage supply significantly improves the frequency and stability of the discharge,which provides a new solution for the realization of a high-frequency,high-energy electron beam source.The peak current amplitude in the high-energy electron beam increases from 6.2 A to 79.6 A,which indicates the pulsed power mode significantly improves the electron beam performance.Besides,increasing the capacitance significantly affects the highcurrent,lower-energy electron beam more than the high-energy electron beam.

The Reform and Practice of Multicultural Cultivation Mode of Art Talents in Colleges and Universities Under the Strategy of “Three Highs and Four New”

As an important link in the development of modern quality education,art education is one of the methods to guide students to have a diversified vision.Under the background of multiculturalism,we need to explore the connotation and value of art education with the concept of“three highs and four new,”so that students can realize interdisciplinary and cross-cultural cognition through an immersive experience and practical operation in a wide range of multicultural situations,and to develop the knowledge of art education with the concept of“three highs and four new.”Based on the multicultural background,this paper focuses on the integration of multiculturalism into the reform practice of“student-centered”in colleges and universities,so as to cultivate art talents adapted to the multicultural background,in order to achieve the great mission of“three highs and four new”and better lead the innovative development of art education in colleges and universities.

Design and performance of a high-speed and low-noise preamplifier for SiPM

Considering the R&D for upgrading the K^(0)_(L) andμdetectors in the Belle II experiment using a scintillator and silicon pho-tomultiplier(SiPM),we designed a compact high-speed and low-noise preamplifier.The preamplifier demonstrated a good gain stability,bandwidth of 426 MHz,baseline noise level ofσ≈0.6 mV,dynamic range of up to170 mV of the input signal amplitude,good time resolution of 20 ps,and it can be comprehensively applied to SiPMs.Adopting pole-zero-cancelation in the preamplifier reduces both the rise and fall times of the SiPM signal,which can significantly improve the time resolution and reduce the pile-up when using a large SiPM or an array of SiPMs.Various combinations of the preamplifier and several types of SiPMs demonstrated time resolutions better than 50 ps for most cases;when the number of detected photons was larger than 60,a time resolution of approximately 25 ps was achieved.

Designing new low alloyed Mg-RE alloys with high strength and ductility via high-speed extrusion

Two new low-alloyed Mg-2RE-0.8Mn-0.6Ca-0.5Zn(wt%,RE=Sm or Y)alloys are developed,which can be produced on an in-dustrial scale via relatively high-speed extrusion.These two alloys are not only comparable to commercial AZ31 alloy in extrudability,but also have superior mechanical properties,especially in terms of yield strength(YS).The excellent extrudability is related to less coarse second-phase particles and high initial melting point of the two as-cast alloys.The high strength-ductility mainly comes from the formation of fine grains,nano-spaced submicron/nano precipitates,and weak texture.Moreover,it is worth noting that the YS of the two alloys can maintain above 160 MPa at elevated temperature of 250°C,significantly higher than that of AZ31 alloy(YS:45 MPa).The Zn/Ca solute segregation at grain boundaries,the improved heat resistance of matrix due to addition of RE,and the high melting points of strengthening particles(Mn,MgZn_(2),and Mg-Zn-RE/Mg-Zn-RE-Ca)are mainly responsible for the excellent high-temperature strength.

Effects of endogenous dopamine induced by low concentration atropine eye drops on choroidal neovascularization in high myopia mice

AIM:To evaluate effects of endogenous dopamine induced by low concentration atropine eye drops on choroidal neovascularization(CNV)in high myopia mice.METHODS:The C57BL/6J mice were deprived of the right eye for 4wk,and the high myopia was diagnosed by optometry,the diopter was less than-6.00 D,and CNV was induced by 532 nm laser.The changes of dopamine D1 receptor(DRD1),dopamine D2 receptor(DRD2),and vascular endothelial growth factor A(VEGFA)were detected by Western blot technology at 0.5,1,2h,and 7d after 0.01%,0.05%,and 0.1%atropine eye drops,respectively,the area of CNV was measured.RESULTS:Significant increases were observed on the expression of DRD2 in mouse high myopia model at 0.5,1,2h,7d with 0.05%and 0.1%atropine eye drops(P<0.05).Significant decreases were observed on the expression of DRD1 and VEGFA in mouse high myopia model at 0.5,1,2h,7d with 0.05%and 0.1%atropine eye drops(P<0.05).The area of CNV induced by laser in the drug-treated group was significantly smaller than that in the control group,and the higher the concentration,the more significant the inhibitory effect(P<0.05).CONCLUSION:The 0.01%,0.05%,0.1%atropine eye drops can decrease the level of VEGFA and inhibit high myopia CNV indirectly by up-regulating the level of DRD2 and down-regulating the level of DRD1,and the effect of 0.05%and 0.1%atropine eye drops is more significant.

Co-Production of High-Grade Dissolving Pulp,Furfural,and Lignin from Eucalyptus via Extremely Low Acid Pretreatment and Pulping Technologies and Catalysis

Hemicellulose and lignin are not reasonably utilized during the dissolved pulp preparation process.This work aimed to propose a process for the co-production of dissolving pulp,furfural,and lignin from eucalyptus.High-grade dissolving pulp was prepared from eucalyptus using a combination of extremely low acid(ELA)pretreatment,Kraft cooking,and elementary chlorine-free(ECF)bleaching.The obtained pre-hydrolysate was catalytic conversion into furfural in a biphasic system,and lignin during Kraft cooking and ECF was recovered.The process condition was discussed as well as the mass flow direction.The results showed that ELA pretreatment could effectively remove 80.1%hemicellulose.Compared with traditional hydrothermal pretreatment,the ELA pretreatment significantly increased the xylose yield from 5.05 to 14.18 g/L at 170℃ for 2 h,which had practical significance for furfural production.The 82.7%furfural yield and 82.9%furfural selectivity were obtained from xylose-rich pre-hydrolysate using NaCl as a phase modifier in a biphasic system with 4-methyl-2-pentanone(MIBK)as an organic phase by ion exchange resin catalysts at 190℃ for 2 h.Subsequently,the pretreated eucalyptus was subjected to Kraft cooking,and the optimal alkali amount was 14%.Then,the Kraft pulp was bleached using the O-D1-EP-D_(2) sequence,and dissolving pulp was obtained with an ISO brightness of 86.0%,viscosity of 463 mL/g,andα-cellulose content of 95.4%.The Kraft lignin which has a potential application was investigated by 2D-HSQC NMR and 31P NMR.The results showed that the S/G ratio of Kraft lignin was 1.93,and the content of phenolic hydroxyl groups was 2.53 mmol/g.Moreover,based on the above proposed process,30.5 g dissolving pulp,5.5 g furfural,and 21.2 g lignin per 100 g eucalyptus chips(oven dry)were produced.This research will provide new catalysis and pulping technical routes for dissolving pulp,furfural,and Kraft lignin products,which are in great demand in the chemical industry.

Diluted low concentration electrolyte for interphase stabilization of high-voltage LiNi_(0.5)Mn_(1.5)O_(4) cathode

The Co-free Li Ni_(0.5)Mn_(1.5)O_(4)(LNMO)is a promising cathode for lithium-ion batteries owing to its high operating voltage and low costs.However,the synthesis of LNMO is generally time and energy consuming,and its practical application is hindered by the lack of a compatible electrolyte.Herein,a spray pyrolysis-based energy-saving synthesis method as well as a diluted low concentration electrolyte(0.5 M LiPF_(6) in a mixture of fluoroethylene carbonate/dimethyl carbonate/1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether(FEC:DMC:TTE,1:4:5 by volume))are proposed to address these challenges.Owing to the unique features of the precursor prepared by spray pyrolysis,well-crystallized LNMO single-crystal can be obtained within 1 h calcination at 900℃.Besides,the fluorinated interphases derived from the diluted low concentration electrolyte not only mitigate the Mn dissolution and Al corrosion at the cathode side,but also suppresses dendritic Li deposition at the anode side,thus enabling stable cycling of both LNMO and Li metal anode.Thus,30μm Li|LNMO(1.75 m A h cm^(-2))cells achieve a high capacity retention(90.9%)after 168 cycles in the diluted low concentration electrolyte.

New insight into the design of highly dispersed Pt supported CeO_(2)-TiO_(2) catalysts with superior activity for VOCs low-temperature removal

A series of CeO_(2)-TiO_(2)mixed oxides supports with various Ce/Ti molar ratio were synthesized by modified coprecipitation method. The corresponding Pt loaded(0.5 wt% Pt) catalysts were prepared by electronless deposition method and evaluated for the deep oxidation of n-hexane as a model VOCs. The results show that the CeO_(2)and TiOxnanoparticles can highly disperse into each other and form Ce_(2)Ti_(2)O_(7)solid solution with appropriate Ce/Ti molar ratio, which significantly improves their redox ability by enhancing the interaction between CeO_(2)and TiO_(x). The dispersibility of Pt species can also be adjusted by altering the Ce/Ti molar ratio, and Pt/CeTi-2/1 catalyst with Ce/Ti molar ratio of 2:1 exhibits the best Pt dispersibility that Pt species mainly exist as Pt single atoms. The high dispersion of Pt species in the Pt/CeO_(2)-TiO_(2)catalysts would promote the catalytic activity of VOCs oxidation with low T90% values(1000 ppm, GHSV = 15,000 h^(-1)), such as for n-hexane degradation with T90% of 139℃. The characterizations reveal that the superior activity is mainly related to possessing the more Pt2+species,adsorbed oxygen species and higher low-temperature reducibility owing to the strong interaction between highly dispersed Pt species and CeO_(2)-TiO_(2)as well as the promoted migration of lattice oxygen by the formation of more Ce_(2)Ti_(2)O_(7)species. Furthermore, the Pt/CeTi-2/1 catalyst also exhibits excellent stability for chlorinated and other non-chlorinated VOCs oxidation, making it very promising for real application under various operating conditions.