等效瞬时电感算法是区分励磁涌流和故障电流的有效方法,但220 k V及以下电压等级的Y/△接线三相变压器多采用三相一体式结构,△侧环流难以获取,因而限制了该算法在此类变压器中的应用。提出一种计算环流的新方法。首先利用变压器等效电...等效瞬时电感算法是区分励磁涌流和故障电流的有效方法,但220 k V及以下电压等级的Y/△接线三相变压器多采用三相一体式结构,△侧环流难以获取,因而限制了该算法在此类变压器中的应用。提出一种计算环流的新方法。首先利用变压器等效电路的微分方程,推导出△侧环流和Y侧零序电流的比例关系。在磁通不饱和区域,Y侧对应相电流和环流相等,因而也和零序电流成比例。然后利用波形相关度理论,分别求取Y侧三相电流与零序电流的相关系数以区分磁通不饱和区域,证明至少可以获取一相长度足够的磁通不饱和区域。利用该段区域内的电流求出比例系数,进而可由Y侧零序电流求得△侧环流。最后通过MATLAB仿真验证了该方法求取△侧环流的准确性。该方法无需已知变压器参数,也无需控制合闸角,在一个工频周期内就能准确求取环流。展开更多
In order to study the wear behavior of different kinds of contact wires,the dry sliding wear behaviors of Cu-Sn,Cu-Ag and Cu-Mg alloys prepared by up-drawn continuous casting and followed continuous extrusion were stu...In order to study the wear behavior of different kinds of contact wires,the dry sliding wear behaviors of Cu-Sn,Cu-Ag and Cu-Mg alloys prepared by up-drawn continuous casting and followed continuous extrusion were studied.The research was tested on a block-on-ring wear tester.The results indicate that the friction coefficient is remarkably influenced by the formation of a continuous tribofilm,which consists of oxidation film.The abrasion,adhesion,oxidation and plastic deformation are observed.Oxidation and abrasion wear mechanisms dominate at the lower sliding velocity and load.The combination of oxidation and adhesion play leading roles with the increasing load and velocity.Plastic deformation is detected under higher applied load and sliding velocities.展开更多
To eliminate rotation deviation of sequential images mosaic when measuring linear dimensions of large scale parts with computer vision, a novel algorithm based on the chain code searching method is proposed. After ima...To eliminate rotation deviation of sequential images mosaic when measuring linear dimensions of large scale parts with computer vision, a novel algorithm based on the chain code searching method is proposed. After image preprocessing, including image filtering, image segmentation, and edge detection, the chain code length of the contour line can be searched out by the proposed method. Then, the angle from the contour line to the coordinate axis is computed with the length of the contour line. After that, the sequence is rotated in the opposite direction and the rotation deviation is eliminated. It is prepared for the next mosaic of sequences in eliminating shifting deviation. Experiments are carried out on parts with a linear profile rotating angle from 0° to 9°. The results show that compared with the commonly used Hough transform, the new method has higher precision and faster speed, which is important in realizing online high precision measurements of large scale parts with a linear profile.展开更多
Based on the combined hydraulic calculation for the eastern network region at the Pearl River estuary and several outlets to the Lingdingyang Bay, the sediment calculation modelling was introduced in the establishment...Based on the combined hydraulic calculation for the eastern network region at the Pearl River estuary and several outlets to the Lingdingyang Bay, the sediment calculation modelling was introduced in the establishment of the sediment mathematical model for Lingdingyang Bay and the eastern region with one and two dimensional flow calculation. Model adjustment and verification were performed in conjunction with field data. The simulated results coincide well with measured data.In addition the model is applied to predict the shore-line planning scheme of Lingdingyang Bay.The theoretical criterion is provided for the shore line plan in the model.And a new mathematical simulated method is put out to research the planning engineering concerned with one-dimensional net rivers and two-dimensional estuary.展开更多
In order to improve the throughput performance of the secondary users （SUs） in the cognitive radio （CR） environment, a quality of service （QoS） based media access control （MAC） protocol is proposed. In this pr...In order to improve the throughput performance of the secondary users （SUs） in the cognitive radio （CR） environment, a quality of service （QoS） based media access control （MAC） protocol is proposed. In this protocol, the CR node maps the channel state as a vector, and the transmitter and the receiver obtain the final channel map through an AND operation to prepare for an optional channel set. Data from the upper application layer are classified into two priority levels according to the QoS requirement. The data of each level relate to different contention windows so that the priority of real time data can be guaranteed. A two-dimensional discrete-time Markov chain is utilized to evaluate the system performance, and mathematical expressions of the system throughput are derived. Simulation results show that compared with the IEEE 802. 11 distributed coordination function （DCF）, the proposed MAC protocol can achieve higher throughput.展开更多
This paper describes a novel method of online composite shape recognition interms of the relevance feedback technology to capture a user's intentions incrementally, and adynamic user modeling method to adapt to va...This paper describes a novel method of online composite shape recognition interms of the relevance feedback technology to capture a user's intentions incrementally, and adynamic user modeling method to adapt to various users' styles. First, the relevance feedback isadapted to refine the recognition results and reduce the ambiguity incrementally based on theestablishment of a feature-based vector model of a user's sketches. Secondly, a dynamic usermodeling is introduced to model the user's sketching habits based on recording and analyzinghistorical information incrementally. A model-based matching strategy is also employed in the methodto recognize sketches dynamically. Experiments prove that the proposed method is both effective andefficient.展开更多
A 2.4GHz monolithic CMOS receiver with direct-conversion architecture is presented. This quadrature receiver is designed for 802.11b wireless LAN applications at the maximum data rate of 11Mbps as a low-cost solution....A 2.4GHz monolithic CMOS receiver with direct-conversion architecture is presented. This quadrature receiver is designed for 802.11b wireless LAN applications at the maximum data rate of 11Mbps as a low-cost solution. Five key blocks,i, e., a low noise amplifier （LNA）, a down-conversion mixer, a variable gain amplifier, a low pass filter, and a DC- offset cancellation circuit,are designed based on system design and low noise high linearity considerations. The necessary auxiliary circuits are also included. Fabricated in SMIC 0.18μm 1p6m RF CMOS process, the receiver＇s performance is measured as：4. 1 dB noise figure, - 7.5dBm input third order intercept point （IIP3） for LNA ＆ mixer at high gain setting, - 14dBm IIP3 for the whole receiver,53dBc @30MHz offset of adjacent channel power rejection,and less than 5mV out- put DC-offset. The receiver consumes 44mA under a 1.8V power supply with I,Q two paths.展开更多
文摘等效瞬时电感算法是区分励磁涌流和故障电流的有效方法,但220 k V及以下电压等级的Y/△接线三相变压器多采用三相一体式结构,△侧环流难以获取,因而限制了该算法在此类变压器中的应用。提出一种计算环流的新方法。首先利用变压器等效电路的微分方程,推导出△侧环流和Y侧零序电流的比例关系。在磁通不饱和区域,Y侧对应相电流和环流相等,因而也和零序电流成比例。然后利用波形相关度理论,分别求取Y侧三相电流与零序电流的相关系数以区分磁通不饱和区域,证明至少可以获取一相长度足够的磁通不饱和区域。利用该段区域内的电流求出比例系数,进而可由Y侧零序电流求得△侧环流。最后通过MATLAB仿真验证了该方法求取△侧环流的准确性。该方法无需已知变压器参数,也无需控制合闸角,在一个工频周期内就能准确求取环流。
基金Projects(51134013,51074031,51274054)supported by the National Natural Science Foundation of China
文摘In order to study the wear behavior of different kinds of contact wires,the dry sliding wear behaviors of Cu-Sn,Cu-Ag and Cu-Mg alloys prepared by up-drawn continuous casting and followed continuous extrusion were studied.The research was tested on a block-on-ring wear tester.The results indicate that the friction coefficient is remarkably influenced by the formation of a continuous tribofilm,which consists of oxidation film.The abrasion,adhesion,oxidation and plastic deformation are observed.Oxidation and abrasion wear mechanisms dominate at the lower sliding velocity and load.The combination of oxidation and adhesion play leading roles with the increasing load and velocity.Plastic deformation is detected under higher applied load and sliding velocities.
基金The National Natural Science Foundation of China(No.50805023)the Program for Special Talent in Six Fields of Jiangsu Province(No.2008144)Jiangsu Provincial Science and Technology Achievement Transformation Project(No.BA2010093)
文摘To eliminate rotation deviation of sequential images mosaic when measuring linear dimensions of large scale parts with computer vision, a novel algorithm based on the chain code searching method is proposed. After image preprocessing, including image filtering, image segmentation, and edge detection, the chain code length of the contour line can be searched out by the proposed method. Then, the angle from the contour line to the coordinate axis is computed with the length of the contour line. After that, the sequence is rotated in the opposite direction and the rotation deviation is eliminated. It is prepared for the next mosaic of sequences in eliminating shifting deviation. Experiments are carried out on parts with a linear profile rotating angle from 0° to 9°. The results show that compared with the commonly used Hough transform, the new method has higher precision and faster speed, which is important in realizing online high precision measurements of large scale parts with a linear profile.
文摘Based on the combined hydraulic calculation for the eastern network region at the Pearl River estuary and several outlets to the Lingdingyang Bay, the sediment calculation modelling was introduced in the establishment of the sediment mathematical model for Lingdingyang Bay and the eastern region with one and two dimensional flow calculation. Model adjustment and verification were performed in conjunction with field data. The simulated results coincide well with measured data.In addition the model is applied to predict the shore-line planning scheme of Lingdingyang Bay.The theoretical criterion is provided for the shore line plan in the model.And a new mathematical simulated method is put out to research the planning engineering concerned with one-dimensional net rivers and two-dimensional estuary.
基金The National Science and Technology Major Project( No. 2010ZX03006-002-01 )the National Basic Research Program of China ( 973 Program) ( No. 2011CB302905)the Science and Technology Support Program of Jiangsu Province ( No. BE2011177)
文摘In order to improve the throughput performance of the secondary users （SUs） in the cognitive radio （CR） environment, a quality of service （QoS） based media access control （MAC） protocol is proposed. In this protocol, the CR node maps the channel state as a vector, and the transmitter and the receiver obtain the final channel map through an AND operation to prepare for an optional channel set. Data from the upper application layer are classified into two priority levels according to the QoS requirement. The data of each level relate to different contention windows so that the priority of real time data can be guaranteed. A two-dimensional discrete-time Markov chain is utilized to evaluate the system performance, and mathematical expressions of the system throughput are derived. Simulation results show that compared with the IEEE 802. 11 distributed coordination function （DCF）, the proposed MAC protocol can achieve higher throughput.
文摘This paper describes a novel method of online composite shape recognition interms of the relevance feedback technology to capture a user's intentions incrementally, and adynamic user modeling method to adapt to various users' styles. First, the relevance feedback isadapted to refine the recognition results and reduce the ambiguity incrementally based on theestablishment of a feature-based vector model of a user's sketches. Secondly, a dynamic usermodeling is introduced to model the user's sketching habits based on recording and analyzinghistorical information incrementally. A model-based matching strategy is also employed in the methodto recognize sketches dynamically. Experiments prove that the proposed method is both effective andefficient.
基金the National Natural Science Foundation of China(No.60606009)~~
文摘A 2.4GHz monolithic CMOS receiver with direct-conversion architecture is presented. This quadrature receiver is designed for 802.11b wireless LAN applications at the maximum data rate of 11Mbps as a low-cost solution. Five key blocks,i, e., a low noise amplifier （LNA）, a down-conversion mixer, a variable gain amplifier, a low pass filter, and a DC- offset cancellation circuit,are designed based on system design and low noise high linearity considerations. The necessary auxiliary circuits are also included. Fabricated in SMIC 0.18μm 1p6m RF CMOS process, the receiver＇s performance is measured as：4. 1 dB noise figure, - 7.5dBm input third order intercept point （IIP3） for LNA ＆ mixer at high gain setting, - 14dBm IIP3 for the whole receiver,53dBc @30MHz offset of adjacent channel power rejection,and less than 5mV out- put DC-offset. The receiver consumes 44mA under a 1.8V power supply with I,Q two paths.
