数字高阶△-∑调制频率合成器的分析与实现

由小数分频频率合成器中相位累加器与数字一阶调制器的等效性出发,用ADS软件仿真证实了高阶数字调制对量化相位噪声的高通整型功能,从而有效地解决了小数分频的杂散问题.最后硬件电路实现了基于调制的小数分频跳频频率合成器,频率范围为590~1000MHz,在偏离主频10KHz时相噪优于-93.76dBc/Hz,频率分辨率可以小于100Hz,转换时间小于50,在跳频频率间隔1MHz时每秒可达2万跳.

A 5mW 1.8V Low Over-Sampling Ratio ΣΔ Modulator with 81dB Dynamic Range

This work demonstrates that the ΣΔ modulator with a low oversampling ratio is a viable option for the high-resolution digitization in a low-voltage environment.Low power dissipation is achieved by designing a low-OSR modulator based on differential cascade architecture,while large signal swing maintained to achieve a high dynamic range in the low-voltage environment.Operating from a voltage supply of 1.8V,the sixth-order cascade modulator at a sampling frequency of 4-MHz with an OSR of 24 achieves a dynamic range of 81dB for a 80-kHz test signal,while dissipating only 5mW.

ANALYSIS OF UN-COINCIDE COORDINATE ERROR IN SINGLE-AXIS ROTATING FIBER OPTIC STRAP-DOWN INERTIAL NAVIGATION SYSTEM

The un-coincide coordinate error in the single-axis rotating fiber optic strap-down inertial navigation system（SINS） is analyzed. Firstly, a rotating modulation technology is presented for SINS. The method provides the enhanced property of SINS when using the same-leveled inertial measurement units. Then, the rotating struc- ture modification is derived and augmented to resolve the un-modulated error-accumulated problem. As the insuf- ficient machine processing, the horizontal and the vertical errors on the machine surface are inevitable, and the in- volved coordinates are difficult to get the exact coincident. So, two major kinds of coordinate situation are stud- ied. The equivalent error models on gyro and acceleration outputs are built for each situation, and the impact is analyzed for compensation. The part of attitude and position error models caused by the built angle-rate error is established to calculate the un-eoincident impact. Considering these conditions of different gyro accuracy and mo- tion states simultaneously, numerical simulations are implemented. Results indicate that the SINS modulation ac- curacy is seriously affected by the combined factors on gyro accuracy and motion conditions.

A High-Performance Silicon Electro-Optic Phase Modulator with a Triple MOS Capacitor

We propose and analyze a novel Si-based electro-optic modulator with an improved metal-oxide-semiconductor （MOS） capacitor configuration integrated into silicon-on-insulator （SOl）. Three gate-oxide layers embedded in the silicon waveguide constitute a triple MOS capacitor structure, which boosts the modulation efficiency compared with a single MOS capacitor. The simulation results demonstrate that the Vπ Lπ product is 2. 4V · cm. The rise time and fall time of the proposed device are calculated to be 80 and 40ps from the transient response curve, respectively,indicating a bandwidth of 8GHz. The phase shift efficiency and bandwidth can be enhanced by rib width scaling.

Three-stage Transformation of Chlorophyll Transient Fluorescence Pattern Under Sustained Dehydration and the Discovery of Critical Water Content in Seaweeds

The chlorophyll fluorescence kinetics of marine red alga Grateloupia turutunt Yamada, green alga Ulva pertusa Kjellm and brown alga Laminaria japonica Aresch during natural sustained dehydration were monitored and investigated. The pulse amplified modulation (PAM) system was used to analyze the distinct fluorescence parameters during thallus dehydration. Results proved that the fluorescence kinetics of different seaweed all showed three patterns of transformation with sustained water loss. These were: 1) peak kinetic pattern (at the early stage of dehydration fluorescence enhanced and quenched subsequently, representing a normal physiological state). 2) plateau kinetic pattern (with sustained water loss fluorescence enhanced continuously but quenching became slower, finally reaching its maximum). 3) Platform kinetic pattern (fluorescence fell and the shape of kinetic curve was similar to plateau kinetic pattern). A critical water content (CWC) could be found and defined as the percentage of water content just prior to the fluorescence drop and to be a significant physiological index for evaluation of plant drought tolerance. Once thallus water content became lower than this value the normal peak pattern can not be recovered even through rehydration, indicating an irreversible damage to the thylakoid membrane. The CWC value corresponding to different marine species were varied and negatively correlated with their desiccation tolerance, for example. Laminaria japonica had the highest CWC value (around 90%) and the lowest dehydration tolerance of the three. In addition, a fluorescence 'burst' was found only in red algae during rehydration. The different fluorescence parameters F-o, F-v and F-v, F-m were measured and compared during water loss. Both F-o and F-v increased in the first stage of dehydration but F-v/F-m. kept almost constant. So the immediate response of in vivo chlorophyll fluorescence to dehydration was an enhancement. Later with sustained dehydration F-o increased continuously while F-v decreased and tended to become smaller and smaller. The major changes in fluorescence (including fluorescence drop during dehydration and the burst during rehydration) were all attributed to the change in F-o instead of F-v This significance of F-o indicates that it is necessary to do more research on F-o as well as on its relationship with the state of thylakoid membrane.

DIGITAL PWM OF AC-AC MATRIX CONVERTER BASED ON OUTPUT-VOLTAGE ERROR FUNCTION

Based on the output-voltage error function, a novel time discrete modulation technique is proposed for matrix converters （MCs） and time-discrete difference equations of a MC circuit are derived. Switch states of MC are obtained when the output voltage error function is minimized, thus the optimum combination of switch states is derived for the closed-loop control of MC. Meanwhile, advantages of the least calculation workload, the simple process, and the convenient for implementation are brought while switch states are described as space vectors in the α-β coordination system. Simulation and experimental results demonstrate the validity of the time-discrete modulation technique and the feasibility of the control approach.

Ridge Waveguide Electro-Optic Polymer Modulator with a New Kind of Corona Poled Crosslinkable Polyurethane

A polymer electro optic modulator has been fabricated with the functional layer acting as a kind of corona poled crosslinkable polyurethane. The three optical layers, namely waveguide, photolithography and oxygen are fabricated by spin coating. With the Reactive Ion Etching method, the ridge of the waveguide is constructed. With light at 1 31μm being fiber coupled to waveguide, the mode and the modulation properties of these devices are demonstrated in a micron control system.

Soft-switching PWM boost full-bridge converter

This paper proposes a family of PWM modulation strategies for boostfull-bridge (FB) converters. The modulation strategies can be classified into two kinds according tothe turn-on sequence of the diagonal switches. The concept of leading switches and lagging switchesis introduced to realize soft-switching. According to the soft-switching realized by the leadingswitches and the lagging switches, two kinds of soft-switching techniques for PWM boost FBconverters yield: zero-current-switching (ZCS) and zero-current and zero-voltage-switching (ZCZVS).Simulation results verify the analysis.

Effects of Different Curing Techniques on Material and Aroma of Flue-cured Tobacco

[Objective] The aim was to compare the effects of three-phase technique, quality and aromatic-flavor improvement technique and Zimbabwe technique on to-bacco quality to select a suitable technique in tobacco production. [Method] Tobacco leaves in down, middle and upper parts of a tobacco variety KRK26 were col ected to analyze raw tobacco quality characters. [Result] With quality and aromatic-flavor improvement technique, the proportions of high-quality and middle/high quality tobac-cos improved by 4.68% and 1.97% and average price enhanced by 1.15 yuan/kg, increasing by 10.33%, 9.07% and 3.12 yuan/kg, compared with three-phase tech-nique. It is proved that the technique would better improve tobacco fragrance and quality and coordinate tobacco fragrance, taste and throat-irritation. [Conclusion] Quality and aromatic-flavor improvement technique provides references for tobacco production.

Effect of Different Flue-curing Techniques on the Taste and Aroma Substances of Tobacco Leaves

[Objective]This study aimed to optimize the conditions for curing tobacco leaf, so as to improve its flavor and quality. [Method] Leaves of Yuanyan 87 were col ected and cured by three different techniques （moderate-intensity conditions throughout the curing course; high-intensity conditions at leaf yel owing and wilting stages, moderate-intensity conditions at leaf drying and vein drying stages; high-in-tensity conditions throughout the curing course）, and then the contents of 48 aroma substances and taste indices of the finished tobacco leaves were measured. [Result] The contents of 28 aroma substances in the tobacco leaves cured under high-inten-sity conditions throughout the course were higher and the taste indices of these to-bacco leaves were better, compared with those flue-cured by the other two tech-niques. The contents of the other 20 aroma substances were not significantly af-fected by the curing techniques. The second best technique was high-intensity con-ditions at leaf yel owing and wilting stages and moderate-intensity conditions at leaf drying and vein drying stages. Curing tobacco leaves at moderate-intensity condi-tions throughout the course was the worst one. [Conclusion] Compared with the oth-er two methods, the contents of aroma substances and taste indices of the tobacco leaves cured under high-intensive conditions throughout the course were the best.

ZERO-CURRENT AND ZERO-VOLTAGE SWITCHING PWM BOOST FULL-BRIDGE CON VERTER

This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load range using the energy of the output capacitor. Ma king use of parasitic capacitors of the lagging switches and parallel auxiliary i nductance with the primary winding of the transformer, the lagging switches can realize zero voltage switching (ZVS) under any load. Compared with the ZCS PWM Boost FB converter, the new converter has no current duty cycle loss. Operat ional principle and parameter design are analyzed. Experimental results verify the effectiveness of the proposed converter.

MANUFACTURING SYSTEM SCHEDULING BASED ON MULTI-AGENT COOPERATION GAME

Aiming at the flexible manufacturing system with multi-machining and multi-assembly equipment, a new scheduling algorithm is proposed to decompose the assembly structure of the products, thus obtaining simple scheduling problems and forming the cOrrespOnding agents. Then, the importance and the restriction of each agent are cOnsidered, to obtain an order of simple scheduling problems based on the cooperation game theory. With this order, the scheduling of sub-questions is implemented in term of rules, and the almost optimal scheduling results for meeting the restriction can be obtained. Experimental results verify the effectiveness of the proposed scheduling algorithm.

Small Signal Equivalent Circuit Model and Modulation Properties of Vertical Cavity-Surface Emitting Lasers

Small signal equivalent circuit model and modulation properties of vertical cavity surface emitting lasers(VCSEL's) are presented.The modulation properties both in analytic equation calculation and in circuit model simulation are studied.The analytic equation calculation of the modulation properties is calculated by using Mathcad program and the circuit model simulation is simulated by using Pspice program respectively.The results of calculation and the simulation are in good agreement with each other.Experiment is performed to testify the circuit model.

INTERFERENTIAL MODULATION-RESOLVED IMAGING OF AN ABSORBING OBJECT HIDDEN IN HIGHLY SCATTERING MEDIUM

In this paper an absorbing object hidden in a highly scattering medium is shown to be visibleunder the illumination of a cw coherent light by using interferometry,and a new filtering algorithm thethreshold density filter is used to extract interference pattern from the speckle noise background fast andefficiently. The submillimeter spatial resolution is achieved.

A generic PWM strategy for multi-leg VSI-fed machine drives

A generic pulse width modulation（PWM） strategy is proposed for the multi-leg voltage source inverter（VSI）.First, the multi-leg VSI is modeled, which is independent from the load structure. Secondly, the proposed PWM strategy is deduced by inverting the mathematical model of the multileg VSI. According to the relationship between the leg number of VSIs and the phase number of electrical machines, the multi-leg VSI-fed machine drives are classified into two types：matched and unmatched applications. The leg numbers of VSIs and the phase number of electrical machines are equal in matched applications while they are different in unmatched applications. The existing PWM strategies cannot be directly used for both matched and unmatched applications. However,the proposed PWM strategy can be general for both matched and unmatched applications, and no modifications are required. The effectiveness of the proposed PWM strategy is verified by experimental results.

Investigation of Mode and Modulation Responses in Semiconductor PS-DFB Lasers:Use of a Vector-Newton Method

A numerical model for steady state analysis and analytical expressions for the AM and FM modulation responses of DFB lasers are presented.The small signal modulation responses of 3 phase shift(PS) DFB is investigated for the first time.A new method(Vector Newton method) to obtain multiple longitudinal mode of DFB lasers is used.It is demonstrated that this method is suitable for obtaining multiple solution of high nonlinear equations.Longitudinal photon density distribution and multiple longitudinal mode of 3PS DFB and simple DFB lasers are analyzed.The results show that modulation response characteristics of 3PS DFB laser is as good as that of DFB,and PS can weaken the longitudinal spatial hole burning (LHSB) effect and is in favor of single longitudinal mode operating of lasers.

Monolithically Integrated Laser Diode and Electroabsorption Modulator with Dual-Waveguide Spot-Size Converter Output

A 1.60μm laser diode and electroabsorption modulator monolithically integrated with a novel dual-waveguide spot-size converter output for low-loss coupling to a cleaved single-mode optical fiber are demonstrated.The devices emit in a single transverse and quasi single longitudinal mode with an SMSR of 25.6dB.These devices exhibit a 3dB modulation bandwidth of 15.0GHz,and modulator DC extinction ratios of 16.2dB.The output beam divergence angles of the spot-size converter in the horizontal and vertical directions are as small as 7.3°×18.0°,respectively,resulting in a 3.0dB coupling loss with a cleaved single-mode optical fiber.

Butt-Joint Monolithically Integrated DFB-LD/EA-MD Light Source for 10Gbit/s Transmission

This paper reports on the design,fabrication,and performance of an integrated electro-absorptive modulated laser based on butt-joint configuration for 10Gbit/s application.This paper mainly aims at two aspects.One is to improve the optical coupling between the laser and modulator;another is to increase the bandwidth of such devices by reducing the capacitance parameter of the modulator.The integrated devices exhibit high static and dynamic characteristics. Typical threshold current is 15mA,with some value as low as 8mA.Output power at 100mA is more than 10mW.The extinction characteristics,modulation bandwidth,and electrical return loss are measured.3dB bandwidth more than 10GHz is monitored.

A Novel Hybrid DPWM for Digital DC-DC Converters

We present a new hybrid digital pulse-width modulator （DPWM） for digital DC-DC converters that employs a ring-oscillator/counter structure. Based on a temperature/process compensation technique and a novel digital controller, the proposed DPWM can not only offer temperature/process-independent pulse widths, but also operate at a much higher clock frequency than the existing delay-line/counter DPWM structure. Post-simulation results show that with our DPWM, the system clock frequency reaches 156.9MHz while the worst variation,in a temperature range of 0 to 100℃under all process corners,is only± 9.4%.

A 64-Step Gray Scale Driver Chip for a 132×64-Pixel Passive Matrix OLED

A mixed-signal driver chip for a 132 × 64-pixel passive matrix OLED panel is presented. The chip has a 64-step gray scale control using the PWM method and two-step voltage pre-charge technology to pre-charge the OLED pixels. It consists of a digital controller,SRAM for display data memory,a DC-DC voltage converter,reference current generators,a pre-charge voltage generator,64 common drivers, and 132 segment drivers. The single chip is a typical current-drive circuit. It has been implemented in a Chartered 0.35/μm 18V HV （DDD） CMOS process with a die area of 10mm× 2mm. Test results show that the power consumption of the whole chip and all pixels with a constant driving current of 100μA while displaying the highest gray scale is 294mW with a 12V high voltage supply and a 3V low voltage supply.