Synthesis of cation exchange resin-supported iron and magnesium oxides/hydroxides composite for nitrate removal in water

In this study,we reported on the concept and practical use of cation exchange resin(CER)for removing anions in water via pretreating the CER with metal salts.The cation exchange resinsupported iron and magnesium oxides/hydroxides composite(FeMg/CER)was synthesized and introduced as a new and potential adsorbent for selective removal of nitrate ion in the water environment.Characteristics of FeMg/CER were determined by techniques such as Fouriertransform infrared spectroscopy,scanning electron microscopy,and Xray diffraction.The results showed that FeMg/CER material had a high nitrate adsorption capacity of 200 mg NO_(3)^()·g^(1)with a fast equilibrium adsorption time of 30 min at pH 5.In addition,it had good durability of at least 10 times of regeneration,which could be applied to practical water and wastewater treatment.

A critical review towards the causes of the iron-based catalysts deactivation mechanisms in the selective oxidation of hydrogen sulfide to elemental sulfur from biogas

Hydrogen sulfide(H_(2)S) not only presents significant environmental concerns but also induces severe corrosion in industrial equipment,even at low concentrations.Among various technologies,the selective oxidation of hydrogen sulfide(SOH_(2)S) to elemental sulfur(S) has emerged as a sustainable and environmentally friendly solution.Due to its unique properties,iron oxide has been extensively investigated as a catalyst for SOH_(2)S;however,rapid deactivation has remained a significant drawback.The causes of iron oxide-based catalysts deactivation mechanisms in SOH_(2)S,including sulfur or sulfate deposition,the transformation of iron species,sintering and excessive oxygen vacancy formation,and active site loss,are thoroughly examined in this review.By focusing on the deactivation mechanisms,this review aims to provide valuable insights into enhancing the stability and efficiency of iron-based catalysts for SOH_(2)S.

Effect of competing solutes on arsenic(Ⅴ) adsorption using iron and aluminum oxides

The study focused on the effect of several typical competing solutes on removal of arsenic with Fe2O3 and Al2O3. The test results indicate that chloride, nitrate and sulfate did not have detectable effects, and that selenium（Ⅳ） （Se（Ⅳ）） and vanadium（Ⅴ） （V（Ⅴ）） showed slight effects on the adsorption of As（Ⅴ） with Fe2O3. The results also showed that adsorption of As（Ⅴ） on A12O3 was not affected by chloride and nitrate anions, but slightly by Se（Ⅳ） and V（Ⅴ） ions. Unlike the adsorption of As（Ⅴ） with Fe2O3, that with Fe2O3 was affected by the presence of sulfate in water solutions. Both phosphate and silica have significant adverse effects on the adsorption of As（Ⅴ） adsorption with Fe2O3 and Al2O3. Compared to the other tested anions, phosphate anion was found to be the most prominent solute affecting the As（Ⅴ） adsorption with Fe2O3 and Al2O3. In general, Fe2O3 has a better performance than Al2O3 in removal of As（Ⅴ） within a water environment where multi competing solutes are present.

Selective catalytic oxidation of NO over iron and manganese oxides supported on mesoporous silica

The selective catalytic oxidation （SCO） of NO was studied on a catalyst consisting of iron-manganese oxide supported on mesoporous silica （MPS） with different Mn/Fe ratios. Effects of the amount of manganese and iron, oxygen, and calcination temperature on NO conversion were also investigated. It was found that the Mn-Fe/MPS catalyst with a Mn/Fe molar ratio of 1 showed the highest activity at the calcination temperature of 400 °C. The results showed that over this catalyst, NO conversion reached 70% under the condition of 280 °C and a space velocity of 5000 h-1. SO2 and H2O had no adverse impact on the reaction activity when the SCO reaction temperature was above 240 °C. In addition, the SCO activity was suppressed gradually in the presence of SO2 and H2O below 240 °C, and such an effect was reversible after heating treatment.

Study on Kinetics of Iron Oxide Reduction by Hydrogen

Kinetics parameters of iron oxide reduction by hydrogen were evaluated by the isothermal method in a differential micro-packed bed. Influence of external diffusion, internal diffusion and heat transfer on the intrinsic reaction rate was investigated and the conditions free of internal and external diffusion resistance have been determined. In the experiments, in order to correctly evaluate the intrinsic kinetics parameters for reducing Fe203 to Fe3O4, the reaction temperatures were set between 440 ℃ and 490 ℃. However, in order to distinguish the reduction of Fe304 to FeO from that of FeO to Fe, the reaction temperature in the experiment was set to be greater than 570 ℃. Intrinsic kinetics of iron oxide reduction by hydrogen was established and the newly established kinetic models were validated by the experimental data.

Dissolution kinetics of iron oxides in clay in oxalic acid solutions

Clay samples containing 8.15% iron oxides and 27.49% alumina were leached in oxalic acid. Leaching experiments were per-formed in aqueous solutions of oxalic acid of 0.2-2 mol/L at 40-80 C for up to 90 min. The mixed kinetic mechanism, i.e., t/τ=[（1 2X/3） （1 X）2/3 ]＋b[ 1 （1 X）1/3], seemed to be the most appropriate one to fit the kinetic data of leaching iron oxides contained in clay in the aqueous oxalic acid solutions. The Arrhenius activation energy for leaching in the 1.8 mol/L oxalic acid was found to be 41.035 kJ/mol.

Column adsorption of Cu(Ⅱ) by polymer-supported nano-iron oxides in the presence of sulfate: Experimental and mathematical modeling

Polymer-supported hydrous iron oxides(HFOs) are promising for heavy metals removal from aqueous systems.The ubiquitous inorganic ligands, e.g., sulfate, are expected to exert considerable impacts on pollutants removal by these hybrid sorbents. Herein, we obtained a hybrid sorbent HFO-PS by encapsulating nanosized HFO into macroporous polystyrene(PS) resin. Both batch and column sorption experiments of Cu(Ⅱ) by HFO-PS were carried out in the presence of sulfate. Obviously, the presence of sulfate is favorable for Cu(Ⅱ) sorption onto HFO-PS.The performances of column Cu(Ⅱ) removal were fitted and predicted with Adams–Bohart, Clark, Thomas and BDST models. Thomas model is suggested best-fit to predict the breakthrough curves. Besides, a linear correlation is observed between breakthrough time and column length based on BDST model, which might be useful for predicting the breakthrough time for Cu(Ⅱ) removal by HFO-PS.

Catalytic performance of cerium iron complex oxides for partial oxidation of methane to synthesis gas

The cerium iron complex oxides oxygen carrier was prepared by the co-precipitation method. The reactions between methane and lattice oxygen from the complex oxides were investigated in a fixed micro-reactor system. The reduced oxygen carder could be re-oxidized by air and its initial state could be restored. The characterizations of the oxygen carders were studied using XRD, O2-TPD, and H2-TPR. The results showed that the bulk lattice oxygen of CeO2-Fe2O3 was found to be suitable for the partial oxidation of methane to synthesis gas. There were two kinds of oxygen species on the oxygen carrier： the stronger oxygen species that was responsible for the complete oxidation of methane, and the weaker oxygen species （bulk lattice oxygen） that was responsible for the selective oxidation of methane to CO and H2 at a higher temperature. Then, the lost bulk lattice oxygen could be selectively supplemented by air re-oxidation at an appropriate reaction condition. CeFeO3 appeared on the oxygen carrier after 10 successive redox cycles, however, it was not bad for the selectivity of CO and H2.

Annealing temperature dependent catalytic water oxidation activity of iron oxyhydroxide thin films

Nanostructured iron oxyhydroxide（Fe OOH） thin films have been synthesized using an electrodeposition method on a nickel foam（NF） substrate and effect of air annealing temperature on the catalytic performance is studied. The as-deposited and annealed thin films were characterized by X-ray diffraction（XRD）,X-ray photoelectron spectroscopy（XPS）, field emission scanning electron microscopy（FE-SEM） and linear sweep voltammetry（LSV） to determine their structural, morphological, compositional and electrochemical properties, respectively. The as-deposited nanostructured amorphous Fe OOH thin film is converted into a polycrystalline Fe;O;with hematite crystal structure at a high temperature. The Fe OOH thin film acts as an efficient electrocatalyst for the oxygen evolution reaction（OER） in an alkaline 1 M KOH electrolyte. The film annealed at 200 °C shows high catalytic activity with an onset overpotential of 240 m V with a smaller Tafel slope of 48 m V/dec. Additionally, it needs an overpotential of 290 mV to the drive the current density of 10 m A/cm;and shows good stability in the 1 M KOH electrolyte solution.

Morphology, chemical compositions and size distribution of rare earth oxides in pure iron

The pure iron was melted and deoxidized by metallic Al and rare earth elements La, Ce and Y respectively at 1600℃ in a vertical resistance furnace. The morphology, chemical composition and size distribution of the inclusions in deoxidized liquid iron have been investigated by using of SEM and image-analysis techniques. The investigated results show that the deoxidation products in molten iron are complex inclusions of rare earth oxide or A12O3 combined with FeO finely distributed. The proper holding time and rapid cooling rate can make inclusions finer. La, Y and Al are more effective than Ce for obtaining finely distributed inclusions.

Relationship Between Iron Oxides and Surface Charge Characteristics in Soils

The relationship between iron oxides and surface charge characteristics in variable charge soils ( latosol and red earth ) was studied in following three ways. ( 1 ) Remove free iron oxides ( Fed ) and amorphous iron oxides ( Feo ) from the soils with sodium dithionite and acid ammonium oxalate solution respectively. ( 2 ) Add 2% glucose ( on the basis of air-dry soil weight ) to soils and incubate under submerged condition to activate iron oxides, and then the mixtures are dehydrated and air-dried to age iron oxides. ( 3 ) Precipitate various crystalline forms of iron oxides onto kaolinite. The results showed that free iron oxides ( Fed ) were the chief carrier of variable positive charges. Of which crystalline iron oxides ( Fed-Feo ) presented mainly as discrete particles in the soils and could only play a role of the carrier of positive charges, and did little influence on negative charges. Whereas the amorphous iron oxides ( Feo ) , which presented mainly as a coating with a large specific surface area, not only had positive charges, but also blocked the negative charge sites in soils. Submerged incubation activated iron oxides in the soils, and increased the amount of amorphous iron oxides and the degree of activation of iron oxide, which resulted in the increase of positive and negative charges of soils. Dehydration and air-dry aged iron oxides in soils and decreased the amount of amorphous iron oxides and the degree of activation of iron oxide, and also led to the decrease of positive and negative charges. Both the submerged incubation and the dehydration and air-dry had no significant influence on net charges. Precipitation of iron oxides onto kaolinite markedly increased positive charges and decreased negative charges. Amorphous iron oxide having a larger surface area contributed more positive charge sites and blocked more negative charge sites in kaolinite than crystalline goethite.

Synergism of Pt nanoparticles and iron oxide support for chemoselective hydrogenation of nitroarenes under mild conditions

An efficient and low-cost supported Pt catalyst for hydrogenation of niroarenes was prepared with colloid Pt precursors andα-Fe2O3 as a support.The catalyst with Pt content as low as 0.2 wt%exhibits high activities,chemoselectivities and stability in the hydrogenation of nitrobenzene and a variety of niroarenes.The conversion of nitrobenzene can reach 3170 molconv h^–1 molPt^–1 under mild conditions(30°C,5 bar),which is much higher than that of commercial Pt/C catalyst and many reported catalysts under similar reaction conditions.The spatial separation of the active sites for H2 dissociation and hydrogenation should be responsible for the high chemoselectivity,which decreases the contact possibility between the reducible groups of nitroarenes and Pt nanoparticles.The unique surface properties ofα-Fe2O3 play an important role in the reaction process.It provides active sites for hydrogen spillover and reactant adsorption,and ultimately completes the hydrogenation of the nitro group on the catalyst surface.

A hydrated amorphous iron oxide nanoparticle as active water oxidation catalyst

Developing efficient water oxidation catalysts(WOCs)with earth‐abundant elements still remains a challenging task for artificial photosynthesis.Iron‐based WOC is a promising candidate because it is economically cheap,little toxic and environmentally friendly.In this study,we found that the catalytic water oxidation activity on amorphous iron‐based oxide/hydroxide(FeOx)can be decreased by an order of magnitude after the dehydration process at room temperature.Thermogravimetric analysis,XRD and Raman results indicated that the dehydration process of FeOx at room temperature causes the almost completely loss of water molecule with no bulk structural changes.Based on this finding,we prepared hydrated ultrasmall(ca.2.2 nm)FeOx nanoparticles of amorphous feature,which turns out to be extremely active as WOC with turnover frequency(TOF)up to 9.3 s^-1 in the photocatalytic Ru(bpy)3^2+‐Na2S2O8 system.Our findings suggest that future design of active iron‐based oxides as WOCs requires the consideration of their hydration status.

Fluidization behavior and reduction kinetics of pre-oxidized magnetite-based iron ore in a hydrogen-induced fluidized bed

The influence of different pre-oxidation temperatures and pre-oxidation degrees on the reduction and fluidization behaviors of magnetite-based iron ore was investigated in a hydrogen-induced fluidized bed.The raw magnetite-based iron ore was pre-oxidized at 800 and1000℃ for a certain time to reach a partly oxidation and deeply oxidation state.The structure and morphology of the reduced particles were analyzed via optical microscope and scanning electron microscopy(SEM).The reaction kinetic mechanism was determined based on the double-logarithm analysis.The results indicate that the materials with higher oxidation temperature and wider particle size range show better fluidization behaviors.The lower oxidation temperature is more beneficial for the reduction rate,especially in the later reduction stage.The pre-oxidation degree shows no obvious influence on the fluidization and reduction behaviors.Based on the kinetic analysis,the reduction progress can be divided into three stages.The reduction mechanism was discussed combing the surface morphology and phase structure.

A model for estimating the rate constant between CO_2-CO gas and molten slag containing iron oxides using optical basicity

A simple model for estimating the rate constant between CO2-CO gas and molten slag containing iron oxides was developed using optical basicity only. In this model, the temperature dependence of the rate constant can be described by the Arrhenius law, and the activation energy can be expressed with a linear function of the slag＇s optical basicity. The model was applied to some molten slag systems, such as FeO, FeO-CaO, FeO-SiO2, FeO-Na2O, FeO-CaO-SiO2, FeO-SiO2-P2O5, FeO-SiOE-Na2O, and FeO-CaO-SiOE-P2O5. A comparison between the predicted results and measured data showed that the model worked well.

Lead and Cadmium Adsorption onto Iron Oxides and Manganese Oxides in the Natural Surface Coatings Collected on Natural Substances in the Songhua River of China

Natural surface coatings collected from natural substances （NSCsNS） were employed to study the roles of the main chemical components （iron oxides, manganese oxides, and other components） in controlling the adsorption of lead（Pb） and cadmium（Cd） in aquatic environments. The selective chemical extraction followed by the adsorption of Pb and Cd experiments and statistical analysis, were used to investigate the adsorption property of each component. Hydroxylamine hydrochloride was used to remove manganese oxides selectively, and sodium dithionite was used to extract iron oxides and manganese oxides. The result indicated that iron oxides and manganese oxides played an important role in the adsorption of Pb and Cd on NSCsNS, and the relative contribution was about two-thirds. The contribution of manganese oxides was the greatest, with a lesser role indicated for other components. The adsorption ability of manganese oxides for Pb and Cd was greater than that of iron oxides or other components for Pb and Cd. The Pb adsorption observed in each component was greater than Cd adsorption.

Hydrogen-based direct reduction of iron oxide at 700℃:Heterogeneity at pellet and microstructure scales

Steel production causes a third of all industrial CO_(2) emissions due to the use of carbon-based substances as reductants for iron ores,making it a key driver of global warming.Therefore,research efforts aim to replace these reductants with sustainably produced hydrogen.Hydrogen-based direct reduction(HyDR)is an attractive processing technology,given that direct reduction(DR)furnaces are routinely operated in the steel industry but with CH_(4) or CO as reductants.Hydrogen diffuses considerably faster through shaft-furnace pellet agglomerates than carbon-based reductants.However,the net reduction kinetics in HyDR remains extremely sluggish for high-quantity steel production,and the hydrogen consumption exceeds the stoichiometrically required amount substantially.Thus,the present study focused on the improved understanding of the influence of spatial gradients,morphology,and internal microstructures of ore pellets on reduction efficiency and metallization during HyDR.For this purpose,commercial DR pellets were investigated using synchrotron high-energy X-ray diffraction and electron microscopy in conjunction with electron backscatter diffraction and chemical probing.Revealing the interplay of different phases with internal interfaces,free surfaces,and associated nucleation and growth mechanisms provides a basis for developing tailored ore pellets that are highly suited for a fast and efficient HyDR.

Preparation of Sulphur-containing Aromatic Amines by Reduction of the Corresponding Aromatic Nitro Compounds with Hydrazine Hydrate over Iron Oxide Hydroxide Catalyst

Sulphur-containing aromatic nitro compounds were rapidly reduced to the corresponding amines in high yields by employing hydrazine hydrate as a hydrogen donor in the presence of iron oxide hydroxide catalyst. It was worth noting that the catalyst exhibited extremely high activity. The reduction could be completed within 20-50 min and the yields were up to 97-99 %.

Reduction and carburization of iron oxides for Fischer–Tropsch synthesis

The activation of iron oxide Fischer–Tropsch Synthesis(FTS) catalysts was investigated during pretreatment: reduction in hydrogen followed by carburization in either CO or syngas mixture, or simultaneously reduction and carburization in syngas. A combination of different complementary in situ techniques was used to gain insight into the behavior of Fe-based FTS catalysts during activation. In situ XRD was used to identify the crystalline structures present during both reduction in hydrogen and carburization. An increase in reduction rate was established when increasing the temperature. A complete reduction was demonstrated in the ETEM and a grain size dependency was proven, i.e. bigger grains need higher temperature in order to reduce. XPS and XAS both indicate the formation of a small amount of carbonaceous species at the surface of the bulk metallic iron during carburization.

Adsorption of Propazine, Simazine and Bisphenol A on the Surface of Nanoparticles of Iron Oxide Nanoparticles of Carbon and Metallic Oxides

Simazine and propazine are selective triazine herbicides currently in use to control broad-leaved weeds and annual grasses around the world. Bisphenol A (BPA) is an industrial chemical used in the production of polycarbonate plastics often found in consumer goods, such as plastic containers, baby bottles etc. These synthetic compounds are known to increase the risk of cancer, cause adverse reproductive effect in reptiles, mammals, birds, humans, and lead to other health problems. They have become some of the principal agents of contamination in water bodies around the world through herbicide runoff, industrial waste and leaching. Some triazines such as atrazine are banned in most European countries for over ten years due to their adverse reproductive effect in mammals, birds and humans;however propazine and simazine are still in use around the world. The removal of these compounds from contaminated water is an exigent challenge. In this study, we investigated their affinity for the surface of nanoparticles (NPS) and standard metallic oxides in an effort to exploit the unique potential applications of NPS for water purification systems. We studied the adsorption of the two triazines and BPA on the surface of NPS of iron (III) oxide, NPS of carbon, bulk iron (III) oxide and aluminum oxide at pH 6 and pH 8 using UV-Visible spectroscopy. Result indicates that these compounds have different affinity towards the surface of metallic oxides and carbon at various pHs. In general, there is relatively high adsorption of some of these compounds on the surface of NPS compared to bulk particles. NPS of carbon have shown the highest affinity for all the three compounds. The lower pH was found to be favorable for all of the compounds except for BPA. BPA have shown high adsorption at pH 8 than at pH 6.