用人因工程学分析评价道路照明质量一道路照明动态测量

观察路面照明本身就是一个光传递系统——路灯发光→路面漫反射→小部分光线进入眼瞳→视网膜之感光细胞引起明亮感觉：从入因工程学考虑，道路照明的主要服务对象是驾驶员．应以驾驶员的视觉感受为基础进行照明设计和测量，应该测量道路的亮度及其均匀度，因为路面照度驾驶员感觉不到，引起驾驶员视觉感应的是路面亮度而不是路面照度。

ANALYSIS AND MEASUREMENT FOR THE DYNAMIC ERRORS OF COORDINATE MEASURING MACHINES

The analysis and calculating method of dynamic errors of CMMs during probing are discussed.To relate the dynamic displacement errors with the dynamic rotational errors a method for obtaining the displacement errors at the probing position from dynamic rotational errors is presented.It is pointed out that the finite element method might be used for modeling dynamic errors.However,dynamic errors are difficult to be modeled so a combined practical and theoretical approach is needed.In addition,the dynamic errors are measured with inductive position sensors.

Assessing dynamic modulus properties for typical asphalt mixtures in Jiangsu

To investigate the validity of two dynamic modulus predictive models（ Witczak 1-37 A viscosity-based model and Witczak 1-40 D shear modulus-based model） in the context of Jiangsu, and evaluate the effect of different mixture design variables（ aggregate gradations, binder type, and volumetric properties） on dynamic modulus E＊, asphalt mixtures commonly used in the local surface layer, including Sup-13 and AC-13, are prepared in the laboratory and their dynamic modulus E＊values are predicted based on the above mentioned models. The corresponding asphalt tests, including viscosity and dynamic shear modulus tests, are also carried out to obtain the prediction model parameters. The test results showthat binder type and asphalt content have a significant impact on dynamic modulus.There is a good correlation between the E＊values based on above two predictive models and the measured E＊, while a relatively lower bias can be expected from Witczak 1-37 A model. The test results can be used for the calibration of dynamic modulus with higher accuracy.

Optimal arrangement for pressure measurement points in working chamber of earth pressure balance shield

In order to exactly provide scientific basis for pressure dynamic balance control of working chamber of earth pressure balance shield (EPBS),study on optimal arrangement of pressure measurement points in working chamber was conducted. Based on mathematical description of optimal arrangement for pressure measurement points,fuzzy clustering analysis and discriminant analysis were used to divide pressure regions of nodes on bulkhead. Finally,the selection method of optimal measurement points was proposed,and by selecting d6.28 m EPBS as study object,the case study was conducted. By contrast,based on optimal arrangement scheme of pressure measurement points,through adopting weighted algorithm,the absolute error mean of equivalent pressure of working chamber is the smallest. In addition,pressure curve of optimal arrangement points presents parabola,and it can show the state of pressure distribution on bulkhead truly. It is concluded that the optimal arrangement method of pressure measurement points in working chamber is effective and feasible,and the method can provide basis for realizing high precision pressure control of EPBS.

Earth＇s Temporal Principal Moments of Inertia and Variable Rotation

Based on the gravity field models EGM96 and EIGEN-GL04C, the Earth＇s time-dependent principal moments of inertia A, B, C are obtained, and the variable rotation of the Earth is determined. Numerical results show that A, B, and C have increasing tendencies; the tilt of the rotation axis increases 2.1×10^ 8 mas/yr; the third component of the rotational angular velocity, ω3 , has a decrease of 1.0×10^ 22 rad/s^2, which is around 23% of the present observed value. Studies show in detail that both 0 and ω3 experience complex fluctuations at various time scales due to the variations of A, B and C.

Numerical Prediction Methods for Clock Deviation Based on Two-Way Satellite Time and Frequency Transfer Data

Three functional models, polynomial, spectral analysis, and modified AR model, are studied and compared in fitting and predicting clock deviation based on the data sequence derived from two-way satellite time and frequency transfer. A robust equivalent weight is applied, which controls the significant influence of outlying observations. Some conclusions show that the prediction precision of robust estimation is better than that of LS. The prediction precision calculated from smoothed observations is higher than that calculated from sampling observations. As a count of the obvious period variations in the clock deviation sequence, the predicted values of polynomial model are implausible. The prediction precision of spectral analysis model is very low, but the principal periods can be determined. The prediction RMS of 6-hour extrapolation interval is Ins or so, when modified AR model is used.

Dynamic measurement on infiltration process and formation mechanism of infiltration front

An infiltration measurement device was developed to research the infiltration process of molten AZ91D magnesium alloy into the Al2O3 short fibre preform.The variation of relationship between the heights of measuring points and the time for molten alloy to reach the measuring points was illustrated.The effect of infiltration process parameters on the infiltration front was analyzed. It is found that pressure and pouring temperature are the most important factors which affect the infiltration velocity and composite quality.Furthermore,considering the influence of temperature field,an infiltration model of molten AZ91D into the short fibre preform was constructed on the basis of experimental results and Darcy’s Law.The analysis shows that the results predicted by this model are consistent with the experimental results.

Optical Measurement System for Motion Characterization of Surface Mount Technology

Advanced testing methods for the dynamics of mechanical microdevices are necessary to develop reliable, marketable microelectromechanical systems. A system for measuring the nanometer motions of microscopic structures has been demonstrated. Stop-action images of a target have been obtained with computer microvision, microscopic interferometry, and stroboscopic illuminator. It can be developed for measuring the in-plane-rigid-body motions, surface shapes, out-of-plane motions and deformations of microstructures. A new algorithm of sub-pixel step length correlation template matching is proposed to extract the in-plane displacement from vision images. Hariharan five-step phase-shift interferometry algorithm and unwrapping algorithms are adopted to measure the out-of-plane motions. It is demonstrated that the system can measure the motions of solder wetting in surface mount technology(SMT).

Online dynamic measurement of saturation-capillary pressure relation in sandy medium under water level fluctuation

An online dynamic method based on electrical conductivity probe, tensiometer and datataker was presented to measure saturation-capillary pressure （S-p） relation in water-light nonaqueous phase liquid （LNAPL） two-phase sandy medium under water level fluctuation. Three-electrode electrical conductivity probe （ECP） was used to measure water saturation. Hydrophobic tensiometer was obtained by spraying waterproof material to the ceramic cup of commercially available hydrophilic tensiometer. A couple of hydrophilic tensiometer and hydrophobic tensiometer were used to measure pore water pressure and pore LNAPL pressure of the sandy medium, respectively. All the signals from ECP and tensiometer were collected by a data taker connected with a computer. The results show that this method can finish the measurement of S-R relation of a complete drainage or imbibition process in less than 60 min. It is much more timesaving compared with 10-40 d of traditional methods. Two cycles of water level fluctuation were produced, and four saturation-capillary pressure relations including two stable residual LNAPL saturations of the sandy medium were obtained during in 350 h. The results show that this method has a good durable performance and feasibility in the porous medium with complicated multiphase flow. Although further studies are needed on the signal stability and accuracy drift of the ECP, this online dynamic method can be used successfully in the rapid characterization of a LNAPL migration in porous media.

Influence of substituting Ni with Co on hydriding and dehydriding kinetics of melt spun nanocrystalline and amorphous Mg_2Ni-type alloys

In order to improve the hydriding and dehydriding kinetics of the Mg2Ni-type alloys,Ni in the alloy is substituted by element Co. The nanocrystalline and amorphous Mg2Ni-type Mg2Ni1-xCox (x=0,0.1,0.2,0.3,0.4) alloys were synthesized by melt-spinning technique. The structures of the as-cast and spun alloys were studied with an X-ray diffractometer (XRD) and a high resolution transmission electronic microscope (HRTEM). An investigation on the thermal stability of the as-spun alloys was carried out with a differential scanning calorimeter (DSC). The hydrogen absorption and desorption kinetics of the alloys were measured with an automatically controlled Sieverts apparatus. The results demonstrate that the substitution of Co for Ni does not alter the major phase of Mg2Ni but results in the formation of secondary phase MgCo2. No amorphous phase is detected in the as-spun Co-free alloy,but a certain amount of amorphous phase is clearly found in the as-spun Co-containing alloys. The substitution of Co for Ni exerts a slight influence on the hydriding kinetics of the as-spun alloy. However,it dramatically enhances the dehydriding kinetics of the as-cast and spun alloys. As Co content (x) increases from 0 to 0.4,the hydrogen desorption capacity increases from 0.19% to 1.39% (mass fraction) in 20 min for the as-cast alloy,and from 0.89% to 2.18% (mass fraction) for the as-spun alloy (30 m/s).

Viscoelastic micromechanical model for dynamic modulus prediction of asphalt concrete with interface effects

A viscoelastic micromechanical model is presented to predict the dynamic modulus of asphalt concrete （AC） and investigate the effect of imperfect interface between asphalt mastic and aggregates on the overall viscoelastic characteristics of AC. The linear spring layer model is introduced to simulate the interface imperfection. Based on the effective medium theory, the viscoelastic micromechanical model is developed by two equivalence processes. The present prediction is compared with available experimental data to verify the developed framework. It is found that the proposed model has the capability to predict the dynamic modulus of AC. Interface effect on the dynamic modulus of AC is discussed using the developed model. It is shown that the interfacial bonding strength has a significant influence on the global mechanical performance of AC, and that continued improvement in surface fimctionalization is necessary to realize the full potential of aggregates reinforcement.

The Influence of Wave State and Sea Spray on Drag Coefficient from Low to High Wind Speeds

Ocean waves alter the roughness of sea surface,and sea spray droplets redistribute the momentum flux at the air-sea interface.Hence,both wave state and sea spray influence sea surface drag coefficient.Based on the new sea spray generation function which depends on sea surface wave,a wave-dependent sea spray stress is obtained.According to the relationship between sea spray stress and the total wind stress on the sea surface,a new formula of drag coefficient at high wind speed is acquired.With the analysis of the new drag coefficient,it is shown that the drag coefficient reduces at high wind speed,indicating that the sea spray droplets can limit the increase of drag coefficient.However,the value of high wind speed corresponding to the initial reduced drag coefficient is not fixed,and it depends on the wave state,which means the influence of wave cannot be ignored.Comparisons between the theoretical and measured sea surface drag coefficients in field and laboratory show that under different wave ages,the theoretical result of drag coefficient could include the measured data,and it means that the new drag coefficient can be used properly from low to high wind speeds under any wave state condition.

Using chaos to improve measurement precision

If the measuring signals were input to the chaotic dynamic system as initial parameters, the system outputs might be in steady state, periodic state or chaos state. If the chaotic dynamic system outputs controlled in the periodic states, the periodic numbers would be changed most with the signals. Our novel method is to add chaotic dynamic vibration to the measurement or sensor system.The sensor sensitivity and precision of a measurement system would be improved with this method. Chaotic dynamics measurement algorithms are given and their sensitivity to parameters are analyzed in this paper. The effects of noises on the system are discussed.

Seat inventory control methods for Chinese passenger railways

Railway seat inventory control strategies play a crucial role in the growth of profit and train load factor. The railway passenger seat inventory control problem in China was addressed. Chinese passenger railway operation features and seat inventory control practice were analyzed firstly. A dynamic demand forecasting method was introduced to forecast the coming demand in a ticket booking period. By clustering, passengers' historical ticket bookings were used to forecast the demand to come in a ticket booking period with least squares support vector machine. Three seat inventory control methods: non-nested booking limits, nested booking limits and bid-price control, were modeled under a single-fare class. Different seat inventory control methods were compared with the same demand based on ticket booking data of Train T15 from Beijing West to Guangzhou. The result shows that the dynamic non-nested booking limits control method performs the best, which gives railway operators evidence to adjust the remaining capacity in a ticket booking period.

Application and dynamical performance simulation of tooth surface measured data of hypoid gear

The tooth surface shape of hypoid gear is very complicated, and tooth surface accuracy of hypoid gear can be measured by using the latticed measurement and scanning measurement. Advantages and disadvantages of the two measurement patterns are compared and application of their measurement data on hypoid gear＇s quality management is analyzed. How to use these measurement data to simulate the dynamical performance of hypoid gear is researched, and the intelligent predicton of the dynamical performance indexes of contact spot, root stress, vibration exciting forces and load distribution and hertz contact stress on the tooth surface are carried out. This research work has an important guiding sense to design and ma- chine hypoid gear with low vibration and noise.

On multistage flexible comprehensive evaluation of complicated system

The paper analyzed characters of complicated system and discussed the reason of comprehensive evaluation, realization of flexible comprehensive evaluation was researched from prospect of dynamic measure selection of evaluation, balance of functionality and harmony, uncertainty factor. In the end, multistage flexible comprehensive evaluation of complicated system was applied to performance evaluation of firm.

F-Rough Integrals and Its Measurements

F-rough integrals is defined on the basis of the dual of function one direction S-rough sets,which has dynamic characteristics.Using F-rough integrals,the concepts of expansion measurement-expansion degree and expansion ratio are given.By expansion degree and expansion ratio the changing extent can be expressed with numbers,and the recognition principle of attribute effect on function equivalences is got.

Improvement of System Dynamic Precision by Dynamic Prediction

According to the characteristic of the sensor inertia, the dynamic prediction to improve the system dynamic precision is presented in this paper. With the recurrence calculation of time constant of the sensor, the system dynamic precision is greatly improved. The example using this method is given.

Selection of the Proper Hammer in Pile Driving and Estimation of the Total Driving Time

There are various methods for analyzing pile driving process such as dynamic formulas, wave equation analyses and dynamic measurements. The programs of the two latter methods are relatively expensive to purchase and also require trained engineers to interpret the data it collects. Meanwhile, the use of the site specific empirical formulas based on the real cases of pile driving and output analyses of the wave equation analysis programs can be beneficial. In the current study, pile driving data from three sites in the south of Iran were collected. Using the data of these cases and one-dimensional wave equation analysis program GRLWEAP, couple of experimental formulas which determine the proper range of hammer＇s ID for driving a pile, are proposed. Finally, due to the importance of the time in marine projects, another experimental formula is also proposed for estimation of the total driving time.

Dynamic effects of high-pressure pulsed water jet in low-permeability coal seams

Mine gas extraction in China is difficult due to the characteristics such as micro-porosity,low-permeability and high adsorption of coal seams.The pulsed mechanismof a high-pressure pulsed water jet was studied through theoretical analysis,experimentand field measurement.The results show that high-pressure pulsed water jet has threedynamic properties.What's more,the three dynamic effects can be found in low-permeabilitycoal seams.A new pulsed water jet with 200-1 000 Hz oscillation frequency andpeak pressure 2.5 times than average pressure was introduced.During bubble collapsing,sound vibration and instantaneous high pressures over 100 MPa enhanced the cuttingability of the high-pressure jet.Through high-pressure pulsed water jet drilling and slotting,the exposure area of coal bodies was greatly enlarged and pressure of the coal seamsrapidly decreased.Therefore,the permeability of coal seams was improved and gas absorptionrate also decreased.Application results show that gas adsorption rate decreasedby 30%-40%and the penetrability coefficient increased 100 times.This proves that high-pressurepulsed water is more efficient than other conventional methods.