Prophylactic Pattern Scanning Laser Retinal Photocoagulation for Diabetic Retinopathy in Spontaneously Diabetic Torii Fatty Rats: Preliminary Experimental Results

Research Background and Purpose: The number of diabetic patients is rapidly increasing, making it crucial to find methods to prevent diabetic retinopathy (DR), a leading cause of blindness. We investigated the effects of prophylactic pattern scanning laser retinal photocoagulation on DR development in Spontaneously Diabetic Torii (SDT) fatty rats as a new prevention approach. Methods: Photocoagulation was applied to the right eyes of 8-week-old Spontaneously Diabetic Torii (SDT) fatty rats, with the left eyes serving as untreated controls. Electroretinography at 9 and 39 weeks of age and pathological examinations, including immunohistochemistry for vascular endothelial growth factor and glial fibrillary acidic protein at 24 and 40 weeks of age, were performed on both eyes. Results: There were no significant differences in amplitude and prolongation of the OP waves between the right and left eyes in SDT fatty rats at 39 weeks of age. Similarly, no significant differences in pathology and immunohistochemistry were observed between the right and left eyes in SDT fatty rats at 24 and 40 weeks of age. Conclusion: Prophylactic pattern scanning retinal laser photocoagulation did not affect the development of diabetic retinopathy in SDT fatty rats.

Effect of Intrauterine Laser Therapy at the IVF Success Rate on Infertile Patients with a History of IVF Failure: A Pilot Non-Blinded Study

Backgrounds: While there’s developing proof aimed toward improving embryo implantation thru a focal point on great development, restrained studies have been performed on enhancing endometrial receptivity. Intrauterine Laser Therapy (LT) can be powerful in selling endometrial cell proliferation, therefore enhancing the achievement of assisted reproductive techniques (ART). The contemporary look at aimed to research the effectiveness of effective intrauterine lasers in growing endometrial thickness and the achievement of being pregnant rate. Materials and Methods: In the current clinical randomized trial (RTC) study, the infertile women (20 - 42 years old) referred to the infertility clinic in 2023-2024 who were candidates for IVF treatment with recurrent implantation failure (RIF) history were included. The patients were divided into two main groups: the intervention group;low level laser therapy (LLLT) after hormone administration) (n = 52) and the control group (hormone administration without LT) (n = 52). The IVF success rate and change in endometrial thickness before and after the LT were compared in groups. Results: There was a significant difference between groups (p Conclusion: It appears that the incorporation of Intrauterine LT in the realm of infertility could significantly impact as a novel supplementary treatment in improving endometrial receptivity and pregnancy rate.

Selective Laser Melting of Novel SiC and TiC Strengthen 7075 Aluminum Powders for Anti-Cracks Application

The aerospace and military sectors have widely used AA7075, a type of 7075 aluminum alloy, due to its exceptional mechanical performance. Selective laser melting (SLM) is a highly effective method for producing intricate metallic components, particularly in the case of aluminum alloys like Al-Si-Mg. Nevertheless, the production of high-strength AA7075 by SLM is challenging because of its susceptibility to heat cracking and elemental vaporization. In this study, AA7075 powders were mechanically mixed with SiC and TiC particles. Subsequently, this new type of AA7075 powder was effectively utilized in green laser printing to create solid components with fine-grain strengthening microstructures consisting of equiaxial grains. These as-printed parts exhibit a tensile strength of up to 350 MPa and a ductility exceeding 2.1%. Hardness also increases with the increasing content of mixed powder, highlighting the essential role of SiC and TiC in SLM for improved hardness and tensile strength performance. .

Ureteroscopy with Holmium: YAG Laser—A Initial Study in the Urology Department of the Pr Bocar Sidy Sall University Hospital of Kati

Introduction: Ureteroscopy is a minimally invasive endoscopic surgery which provides access to the ureter, pyelon and calyceal cavities via the urethra and the bladder. Laser ureteroscopy uses the laser as an energy source to treat the stone and eliminate it naturally. Minimally invasive endoscopic methods are struggling to become popular in sub-Saharan African countries, especially for the upper urinary tract. The objective of our work was to report the results of our first laser ureteroscopy experience in the department. Materials and Methods: This was a prospective and descriptive study running from December 1, 2023 to February 19, 2024. Included in our study was any case of upper urinary tract stone operated by Laser ureteroscopy. The characteristics of the lithiasis were determined by CT scan. Sterilization of urine was verified by carrying out a cytobacteriological examination of urine. Ureteral lithiasis was approached by semi-rigid ureteroscopy. Renal lithiasis was immediately addressed by flexible ureteroscopy. Ureteroscopy was coupled with a Holmium YAG laser. A double J ureteral catheter was placed after the operation. A 230 µm laser fiber was used in each case with a generator with a power of 35 watts (Storz Calculase III type). An access sheath was used in all cases of flexible ureteroscopy. The parameters studied were: sociodemographic characteristics, lithiasis (site, size, number, density, topography), type of anesthesia, duration of laser use, duration of intervention, postoperative outcomes. Data entry and analysis were carried out using the software (Word 2016 and SPSS). Result: We collected 30 cases of laser ureteroscopy. The average age was 37 years with extremes of 9 and 79 years. The male gender was more represented. The most common age group was 24-39 years old. Renal colic was the most frequent reason for admission, 12 patients (40%). On physical examination, lumbar tenderness was present in 47% (14 patients). ECBU was positive in 4 patients (13%). CT scan was performed in all our patients before the intervention. The average stone size was 12 mm and the largest was 23 mm. The majority of stones, i.e. 59% (18 patients), had a density greater than 1000 HU. The stone was unique in 19 patients (63%). The location of the stone was pyelic in 8 patients or 27%. An impact on the upper urinary tract was found in 16 of our patients or 53%. General anesthesia was used in 25 patients (83%). A digital flexible ureteroscopy was used in 24 patients and a semi-rigid ureteroscopy (URS) in 6 patients. Full-course fragmentation was the most used therapeutic method, 9 patients or 32%. The average duration of interventions was 61 minutes. Drainage by double J catheter at the end of the procedure was performed in all our patients. The length of hospitalization was 24 hours. Only one case of failure in the USSR was recorded, and one case of failure was in the semi-rigid URS. Conclusion: Laser ureteroscopy is an effective minimally invasive surgery in the management of lithiasis of the upper urinary tract. It significantly reduces the length of hospitalization. Mastery of this technique and the acquisition of the equipment necessary for its implementation is an undeniable asset in the management of renal and ureteral lithiasis.

Identification of Sudanese Sesame Oil Quality Using a 680 nm Semiconductor Laser Spectrometer and Other Techniques

This study investigates the optical properties of sesame oil from traditional and industrial sources using a custom-designed semiconductor laser spectrometer, UV-Vis spectroscopy, and FTIR spectroscopy. Six samples were collected from traditional presses and factories in Khartoum State and White Nile State. The spectrometer, constructed with a 680 nm semiconductor laser and various resistor values, measured the absorbance of sesame oil samples. UV-Vis spectroscopy identified absorbance peaks at 670 nm and 417 nm, corresponding to chlorophyll a and b. FTIR analysis showed nearly identical spectra among the samples, indicating similar chemical compositions. Laser spectrometer analysis revealed specific absorbance values for each sample. The results highlight the feasibility of using a 680 nm semiconductor laser for analyzing sesame oil, providing a cost-effective alternative to other wavelengths. This study demonstrates the potential of integrating traditional methods with modern spectroscopic techniques for the quality assessment of sesame oil.

表面张力对激光焊接熔池及匙孔的影响

基于FLUENT19.0软件,建立了激光焊接热-流耦合模型,对比分析了不同表面张力温度系数(为负值)对熔池流场的影响.结果表明,随着表面张力温度系数的减小,熔池后方顺时针漩涡的流动趋势逐渐减弱,甚至消失,而且焊接飞溅的数量增多.纵截面熔池长度逐渐增加,纵截面熔池流体最大流动速度逐渐增大,熔池横截面的面积逐渐减小.当表面张力温度系数为-2.5×10^(-4)N/(m·K)时,熔池长度平均值为3.28 mm、熔池流体最大流动速度的平均值为2.89 m/s、熔池横截面面积的平均值为4.52 mm^(2);当表面张力温度系数为-3.5×10^(-4)N/(m·K)时,熔池长度平均值为3.73 mm、熔池流体最大流动速度的平均值为3.53 m/s、熔池横截面面积的平均值为4.03 mm^(2);当表面张力温度系数为-4.9×10^(-4)N/(m·K)时,熔池长度平均值为4.14 mm、熔池流体最大流动速度的平均值为4.09 m/s、熔池横截面面积的平均值为3.28 mm^(2).

气管内超声引导纵隔肿瘤激光多点消融操作流程

由于纵隔解剖位置复杂,重要脏器较多,纵隔肿瘤的治疗一直是临床难点。相比传统局部治疗,气道内超声引导纵隔肿瘤激光多点消融具有较多优势,包括消融范围及效果可实时监控、避免损伤正常组织、不良反应少、耐受性好等。该文阐述了气管内超声引导纵隔肿瘤激光多点消融的操作流程。

基于多线激光雷达的井下斜坡道无人矿卡定位与建图方法

井下斜坡道的定位与建图是实现井下斜坡道无人驾驶的关键技术之一,矿山井下斜坡道区域为典型非结构化环境特征,且道路具有一定倾斜角度,采用传统SLAM算法无法获得精确里程计信息,导致定位与建图精度难以满足无人矿卡行驶需求。针对上述问题,通过研究激光SLAM(Simultaneous Localization And Mapping)算法LeGO-LOAM,笔者提出一种适用于矿山井下斜坡道环境的定位与建图方法。首先,针对井下斜坡道口两侧均为光滑水泥墙壁,特征点稀少问题,设计了基于人工路标的辅助增强定位方法,有效增加点云特征数量,从而优化位姿估计结果,避免建图漂移现象;然后在特征预处理阶段,提出了一种基于激光点云高度差与坡度信息融合的提取地面点高效算法,通过改善地面地点的选取策略,针对倾斜坑洼路面仍能有效识别地面点,解决了井下斜坡道定位与建图倾斜角度大、误差大等问题;其次,基于CVC(Curved-Voxel Clustering)聚类算法设计了一种斜坡道点云曲率体素聚类算法,采用曲率体素和基于哈希的数据结构对点云进行分割,大幅提高在井下稀疏、噪声环境下点云聚类的鲁棒性;最后,运用Scan-To-Map进行点云匹配,同时兼顾点云配准的性能与速度。在中钢集团山东某井下斜坡道的现场实验证明:与原算法相比精度提升13.15%,Z轴误差降低22.3%,地图质量明显提升,能有效解决井下无人驾驶建图及定位的难题。

海面溢油激光探测系统及相关算法的研究

激光诱导荧光(LIF)技术是目前较为有效的海面溢油探测技术之一,但基于该技术的油膜厚度反演算法不适用于评估厚油膜(>800μm)。激光方向性强且能量集中,研究已表明其具备评估海面油膜的能力,然而现有探测系统将激光信号作为干扰信号加以抑制或去除。为了重新找回该信号以实现探测海面厚油膜的目的,研究了一种海面溢油激光探测系统并对其协调控制方法进行了探讨,另外,基于此系统建立了一种利用激光反射信号评估海面厚油膜的模型。通过选用原油和白油的混合油(1:50)作为实验油,验证了海面溢油激光探测系统的可行性和油膜厚度评估算法的有效性。

高温声学检测技术的发展、应用与挑战

以我国航空航天、钢铁冶金、特种设备等领域的高温声学无损检测技术研究与应用为主线,分析了高温声学检测技术在促进先进高温材料制备与研发、钢铁冶金行业绿色低碳生产和产业升级、高温压力管道安全运行与维护等方面的巨大需求。介绍了国内外在高温声学检测的技术方法和仪器研制等方面取得的进展,分析了压电超声、电磁超声、激光超声、激光电磁超声等技术在高温无损检测应用方面存在的优缺点和应用场景,总结了高温声学检测技术面临的机遇与挑战。

基于锥形掺镱光纤实现20 kW高光束质量激光输出

锥形光纤能够有效兼顾非线性效应抑制和模式控制,具备实现高功率、高光束质量光纤激光的潜力。近期国防科技大学研制了锥形掺镱光纤,采用1 018 nm光纤激光后向级联泵浦实现了20.2 kW激光输出,光束质量β因子平均值优于2,拉曼抑制比为33 dB。研究结果展示了锥形光纤在实现万瓦级高光束质量激光方面的优势。

近地小行星材料特性对激光烧蚀驱动效率的影响试验分析

基于激光驱动效果和小行星材料特性密切相关的问题,针对脉冲激光对近地小行星物质的烧蚀驱动效率开展了试验研究,选用不同材质、孔隙率的类小行星试验样品,开展了冲量耦合规律测量试验。试验结果表明:在脉冲激光烧蚀的作用下,C型小行星比S型小行星具有更高的冲量耦合效率;随着小行星孔隙率的升高,冲量耦合效率降低,激光烧蚀驱动的效率下降。此外,还对激光烧蚀类小行星物质质量变化的规律进行试验,试验结果表明存在使得小行星质量烧蚀效率最佳的激光功率密度。对于需长期预警时间的威胁小行星,在烧蚀驱动偏转其轨道的同时,以最快的速率减少其质量,可进一步提升防御效率,实现防御的目的。

激光剥蚀电感耦合等离子体质谱法微区原位定量分析锂铍矿物化学成分

锂、铍是当前全球战略性关键金属,采用激光剥蚀电感耦合等离子体质谱(LA-ICP-MS)建立分析方法可以实现微区原位定量分析天然矿物样品中的锂、铍元素含量,为锂铍资源高效利用以及赋存状态的研究提供分析技术支撑。锂辉石和绿柱石等矿物是提取锂、铍元素的主要原料,微区分析常用的电子探针方法对于能量较低的轻元素难以准确定量,而LA-ICP-MS方法亟待改进降低非基体匹配校准带来的基体效应提高分析的准确度和精密度。本文探讨了仪器工作条件(同位素选择及计数模式、载气He气流速、样品气Ar气流速、束斑直径、能量密度大小)和数据处理方法(外部标准物质、内标元素)对定量结果精密度和准确度的影响。实验结果表明:He和Ar气体流速不仅会影响锂、铍信号强度,而且适当降低载气He流速(0.6L/min)可以减小相对误差。增加束斑直径虽可以将数据精密度提高10%以上,但是对于准确度影响不大;对于绿柱石这类硬度高的透明矿物应提高能量密度(相对强度>75%,通量>2.7J/cm^(2))以保证产生稳定剥蚀信号。测定7Li时选择现有标准物质中含量较高的GSE-1G校准、9Be选择NIST610校准,以Al作为内标补偿元素,计算结果相对误差较小。LA-ICP-MS方法通过调整仪器工作条件和数据处理方法,可以降低基体差异,提高数据准确度,解决微区原位准确定量分析锂、铍轻元素的难题,为锂、铍资源的勘探开发和高效利用提供有力的技术支撑。但是也亟待开发高锂、铍含量的微区标准物质,解决因现有标准物质与样品中含量差异造成的基体效应来进一步提高数据质量。

LIBS结合图像筛选方法提高钢铁中Cu、Cr、Mn元素检测稳定性研究

优质特种钢材和低端粗钢之间的性能差异主要受其构成元素种类及其成分含量的影响,因此,如何快速准确地对物质成分进行定性及定量分析对钢铁产品的质量评估至关重要。针对传统方法难以实现对钢铁合金成分的快速准确检测的难题,采用激光诱导击穿光谱(LIBS)结合等离子体图像信息的方法,通过快速地对不同元素的特征光谱强度与激发生成的等离子体图像进行采集,分析两者之间的相关性,并通过提取的图像特征信息的异常值剔除了部分无效光谱数据,进而实现了对钢铁成分的高精度分析。通过分析延迟时间和激光能量等不同实验条件对元素特征光谱强度及其对应等离子体图像的影响规律,不仅证明了等离子体图像与光谱之间存在相关性,还利用等离子体图像特征信息的局部最优值确定了最优延迟时间、激光能量分别为1000 ns与50 mJ,并根据图像特征的平均阈值来筛选无效光谱数据。结果表明,图像筛选优化数据后,各元素谱线校准模型的决定系数(R^(2))分别从原始数据的0.978、0.986、0.957、0.935提升至0.995、0.997、0.968、0.957,且其定标曲线对未知样品元素的预测浓度相对标准偏差(RSD)下降为原始数据预测浓度RSD的50%左右。由此可知采用LIBS结合图像筛选方法可以减少定量分析的误差,提高预测结果精确度。

热处理对选区激光熔化Al-Mn-Mg-Sc-Zr合金力学性能和腐蚀行为的影响

以Al-4.77Mn-1.37Mg-0.67Sc-0.25Zr(质量分数,%)合金粉末为原料,在激光功率330 W和扫描速率700 mm/s下进行选区激光熔化(Selective laser melting,SLM)形成SLM Al-Mn-Mg-Sc-Zr合金,结合慢应变速率拉伸实验、电化学测试、析氢浸泡实验及显微组织表征手段,分析了(350℃,8 h)热处理对SLM Al-Mn-Mg-Sc-Zr合金力学性能和腐蚀行为的影响。结果表明:SLM Al-Mn-Mg-Sc-Zr合金力学性能优异,抗拉强度、屈服强度和伸长率分别为423 MPa、376 MPa和25.1%。热处理后,SLM Al-Mn-Mg-Sc-Zr合金晶内析出大量针棒状纳米Al_(6)Mn相,抗拉强度和屈服强度分别提升至509 MPa和478 MPa。此外,SLM Al-Mn-Mg-Sc-Zr合金具有良好的耐蚀性能,热处理可以促进SLM Al-Mn-Mg-Sc-Zr合金的钝化,在-0.5 V极化电位时出现钝化台阶,降低SLM Al-Mn-Mg-Sc-Zr合金的电流密度,增加SLM Al-Mn-Mg-Sc-Zr合金的阳极极化率,使SLM Al-Mn-Mg-Sc-Zr合金的平均析氢速率从0.242 mL/(cm^(2)·h)降至0.216 mL/(cm^(2)·h),应力腐蚀敏感因子从3.379%降至0.405%。与此同时,热处理也促进了晶内微米富Si相以及晶界富Mn相和Mg相的析出,增加了SLM Al-Mn-Mg-Sc-Zr合金点蚀形核位置,增大了SLM Al-Mn-Mg-Sc-Zr合金的晶界电化学成分非均匀性,降低了SLM Al-Mn-Mg-Sc-Zr合金的点蚀和晶间腐蚀抗力。

Efficacy and Safety of Alexandrite and Nd:YAG Laser Combination in Permanent Hair Removal

Background and Objective: Unwanted hair growth is a discomforting issue affecting both genders. People have tried various methods to get rid of this situation. This study aims to evaluate the efficacy and safety of a combined Alexandrite and Nd:YAG laser treatment for permanent hair removal, drawing insights from existing literature. Materials and Methods:This study included a total of 2127 patients (302 males, 1825 females) aged 18 - 65, with complete data, who underwent hair removal treatment between December 2018 and April 2021. These patients were treated using the Duetta laser system (Quanta system, Samarate, Italy), combining Alexandrite 755 nm and Nd:YAG 1064 nm wavelengths. The patients’ skin types were classified according to the Fitzpatrick classification scale. Target area/areas for laser hair removal was/were determined. Laser parameters, pulse counts, pain levels assessed through the Visual Pain Scale (VPS), and patient satisfaction were documented based on skin types. Findings: Across various skin types, Types I - II exhibited the highest treatment success rates (87%), with the axillary region achieving the highest rate (83%) and the face region achieving the lowest rate (75%). Pain scale analysis indicated that 98% of patients tolerated the procedure well. Patient satisfaction levels exceeded 90%. Evaluation of complication rates revealed minimal occurrences. Conclusion: The combined Alexandrite and Nd:YAG laser system demonstrates both efficacy and safety across diverse skin types, attributed to its notable success rates, minimal adverse effects, and high patient tolerance.

重熔对超高速激光熔覆Fe基涂层组织性能的影响

采用中心送粉式超高速激光熔覆方法在Q460钢基体制备Fe基合金涂层,并对涂层进行激光重熔处理,之后利用激光共聚焦(LCSM)、光学显微镜(OM)、扫描电镜(SEM)、X射线衍射仪(XRD)及电化学工作站、显微硬度计、摩擦磨损仪分析重熔前后熔覆层的宏观形貌、微结构及性能。同时,利用COMSOL软件模拟熔覆和重熔过程涂层热场分布。结果表明:中心送粉式超高速激光单次熔覆可成形微米级厚的Fe基涂层,涂层无裂纹、孔洞等缺陷,稀释率仅为6.82%;重熔后的涂层平整度增加且近表面晶粒明显细化,沿生长方向呈梯度结构;重熔样品具有更高的耐腐蚀性,硬度提高约33%,表现出更优的耐磨性;模拟发现,重熔过程中涂层表面的温度梯度明显高于涂层内部,导致涂层梯度结构的形成,涂层表面晶粒细化有利于其表面耐蚀耐磨综合性能的提升。

激光诱导击穿光谱技术对钕铁硼永磁材料中多元素的定量表征

“磁王”钕铁硼是现今性能最为优异的永磁体,因其优异的磁性能被广泛应用于工业互联网、新能源、 5G通讯等诸多高新科技领域。目前研究钕铁硼材料中元素成分的主要分析方法有电感耦合等离子体发射光谱(ICP-OES)和X射线荧光光谱(XRF),其中ICP-OES是湿法分析,样品前处理复杂,测试周期长,而XRF法可实现直接分析,但受制于其轻元素的检测能力很难满足对钕铁硼材料中主要轻元素B的分析需求。激光诱导击穿光谱(LIBS)技术具有分析效率高,样品前处理简单,多元素直接分析,适用于现场分析、在线分析等技术优点,使其在快速定量表征方面展现出其独有的优势。运用LIBS分析技术开展对钕铁硼材料中多元素定量表征的直接、快速分析的方法研究,首先针对钕铁硼材料中定量表征的九个元素Nd、 Co、 B、 Dy、 Tb、 Pr、 Cu、 Al、 Ga完成特征谱线的筛选,通过对系统激光器电压、激光剥蚀方式等因素在不同条件下对钕铁硼材料光谱信号稳定性的影响分析,优化并确立了分析条件,最终选用720V的激光器电压,15个预剥蚀脉冲15个剥蚀脉冲的激光剥蚀方式为钕铁硼样品的分析条件;其次,选取8个通过ICP-OES法定值的烧结钕铁硼样品,样品具有元素成分的梯度差异化特征,作为建立分析方法的标准样品,采用标准曲线法通过相对强度与浓度的关联方式,建立钕铁硼样品中Nd、 Co、 B、 Dy、 Tb、 Pr、 Cu、 Al、 Ga九个元素的定量分析校准曲线;最后选取两个烧结钕铁硼试样,运用建立的定量分析方法完成九个元素的定量表征,分析时间小于30 s,其定量结果与ICP-OES法测定结果的比对,具有较好的一致性。运用激光诱导击穿光谱分析技术实现了对钕铁硼材料中多元素成分的直接、同时、快速定量表征,为钕铁硼材料的快速定量表征提供了新的技术思路和表征方法。

便携式激光诱导击穿光谱仪测定土壤中重金属

土壤重金属污染对农作物生长和人体健康都有严重危害,现场快速检测对土壤重金属污染调查、应急监测具有重要意义。采用自主研发的土壤重金属激光诱导击穿光谱现场快速检测仪对矿区周边土壤进行现场检测分析,以835个不同基质土壤的光谱数据建立定标数据库,通过支持向量机建立回归模型对土壤重金属元素含量进行定量反演。现场检测获取的全波段光谱波动在15%以内,Cd、Cr、Cu、Ni、Pb和Zn等6种元素光谱强度相对标准偏差平均值为6.31%。将检测结果与实验室电感耦合等离子体质谱法分析对比,6种元素的皮尔逊相关系数r在0.8501~0.9829,检测结果80%以上处于±30%相对误差区间分布。对比结果表明自主研发的土壤重金属激光诱导击穿光谱现场检测仪可以满足现场快速检测需求。

激光冲击强化技术在核电领域的研究进展

激光冲击强化技术属于改善金属性能的重要表面形变强化技术,因其独特的技术优势在航天及船舶领域获得广泛应用。随着科技的发展研发出多种激光冲击强化技术,并逐渐开始在核电装备领域获得应用,然而针对该技术在核电领域的研究进展缺乏系统的综述。先通过介绍不同表面形变强化技术,叙述激光冲击强化技术的发展,阐述激光冲击强化机制,最后综述激光冲击强化技术在核电领域的应用研究进展。总结发现,激光冲击强化技术可有效改善核电领域材料力学、摩擦磨损及腐蚀性能,但传统和添加辅助手段激光冲击强化技术受约束层和吸收层影响较大,无涂激光冲击强化技术对金属易产生热效应,飞秒激光冲击强化影响层浅且强化效果差,不同工艺技术在核电领域提升摩擦磨损性能研究较少。对不同工艺激光冲击强化机理及在核电领域材料不同性能的提升进行深入研究,为进一步提升激光冲击强化技术在核电领域材料的应用提供理论基础,可为核电领域关键装备进行强化、提升核电装备运行寿命提供参考。