Graphitized carbon foams(GFms)were prepared using mesophase pitch(MP)as a raw material by foaming(450℃),pre-oxidation(320℃),carbonization(1000℃)and graphitization(2800℃).The differences in structure and properties...Graphitized carbon foams(GFms)were prepared using mesophase pitch(MP)as a raw material by foaming(450℃),pre-oxidation(320℃),carbonization(1000℃)and graphitization(2800℃).The differences in structure and properties of GFms prepared from different MP precursors pretreated by ball milling or liquid phase extraction were investigated and compared,and semi-quantitative calculations were conducted on the Raman and FTIR spectra of samples at each preparation stage.Semi-quantitat-ive spectroscopic analysis provided detailed information on the structure and chemical composition changes of the MP and GFm de-rived from it.Combined with microscopic observations,the change from precursor to GFm was analyzed.The results showed that ball milling concentrated the distribution of aromatic molecules in the pitch,which contributed to uniform foaming to give a GFm with a uniform pore distribution and good properties.Liquid phase extraction helped remove light components while retaining large aromatics to form graphitic planes with the largest average size during post-treatment to produce a GFm with the highest degree of graphitization and the fewest open pores,giving the best compression resistance(2.47 MPa),the highest thermal conductivity(64.47 W/(m·K))and the lowest electrical resistance(13.02μΩ·m).Characterization combining semi-quantitative spectroscopic ana-lysis with microscopic observations allowed us to control the preparation of the MP-derived GFms.展开更多
Aluminum foams were fabricated by melt-based route using ZrH2 as a foaming agent. The factors which affected the foaming of aluminum foams during casting process were investigated. The powdered zirconium hydride with ...Aluminum foams were fabricated by melt-based route using ZrH2 as a foaming agent. The factors which affected the foaming of aluminum foams during casting process were investigated. The powdered zirconium hydride with content of 0.6%-1.4% （mass fraction） was added to the molten pure aluminum and the foaming condition was controlled in a temperature range from 933 to 1 013 K, Ca amount of 1.5%-3.0% （mass fraction）, stirring time of 0.5-2.5 min and holding time of 1.5-4.0 min to obtain homogeneous aluminum foams. The fabricated aluminum foams were characterized by XRD, SEM and Image-pro plus. The mechanical properties of the aluminum foams with different relative density were tested. The result indicates that the foaming agent （ZrH2） is suitable for the preparation of small aperture aluminum foams with average pore diameter of 1 mm. Inter-metallic compounds and Al2O3 have effect on the melt viscosity. The aluminum foams experience linear elastic, platforms and densification process and had a higher efficiency of energy absorption.展开更多
Static three-point bending tests of aluminum foam sandwiches with glued steel panel were performed. The deformation and failure of sandwich structure with different thicknesses of panel and foam core were investigated...Static three-point bending tests of aluminum foam sandwiches with glued steel panel were performed. The deformation and failure of sandwich structure with different thicknesses of panel and foam core were investigated. The results indicate that the maximum bending load increases with the thickness of both steel panel and foam core. The failure of sandwich can be ascribed to the crush and shear damage of foam core and the delamination of glued interface at a large bending load, The crack on the foam wall developed in the melting foam procedure is the major factor for the failure of foam core. The sandwich structure with thick foam core and thin steel panel has the optimal specific bending strength. The maximum bending load of that with 8 mm panel and 50 mm foam core is 66.06 kN.展开更多
A multi-parameter nonlinear elasto-plastic constitutive model which can fully capture the three typical features of stress-strain response, linearity, plasticity-like stress plateau and densification phases was develo...A multi-parameter nonlinear elasto-plastic constitutive model which can fully capture the three typical features of stress-strain response, linearity, plasticity-like stress plateau and densification phases was developed. The functional expression of each parameter was determined using uniaxial compression tests for aluminum alloy foams. The parameters of the model can be systematically varied to describe the effect of relative density which may be responsible for the changes in yield stress and hardening-like or softening-like behavior at various strain rates. A comparison between model predictions and experimental results of the aluminum alloy foams was provided to validate the model. It was proved to be useful in the selection of the optimal-density and energy absorption foam for a specific application at impact events.展开更多
The two kinds of rigid polyurethane （PU） foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in...The two kinds of rigid polyurethane （PU） foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in weight. The indexes of mechanical performance, apparent density, thermal stability and aging resistance were separately tested for the prepared PU foams. The results show that the mechanical property, thermal insulation and thermal stability for PU foam with modified alkali lignin are excellent among two kinds of PU foams and control samples. The additions of the refined alkali lignin and modified alkali lignin to PU foam have little effect on the natural aging or heat aging resistance except for decreasing hot alkali resistance apparently. Additionally, the thermal conductivity of modified alkali lignin PU foam is lowest among two kinds of PU foams and control samples. The alkali lignin PU foam modified by 3-chloro-1,2-epoxypropane could be applied in the heat preservation field.展开更多
Based on A356 aluminum alloy,aluminum foams were prepared by gas injection foaming process with pure nitrogen,air and some gas mixtures.The oxygen volume fraction of these gas mixtures varied from 0.2%to 8.0%.Optical ...Based on A356 aluminum alloy,aluminum foams were prepared by gas injection foaming process with pure nitrogen,air and some gas mixtures.The oxygen volume fraction of these gas mixtures varied from 0.2%to 8.0%.Optical microscopy,scanning electron microscopy（SEM） and Auger electron spectroscopy（AES） were used to analyze the influence of oxygen content on cell structure,relative density,macro and micro morphology of cell walls,coverage area fraction of oxide film,thickness of oxide film and other aspects.Results indicate that the coverage area fraction of oxide film on bubble surface increases with the increase of oxygen content when the oxygen volume is less than 1.2%.While when the oxygen volume fraction is larger than 1.6%,an oxide film covers the entire bubble surface and aluminum foams with good cell structure can be produced.The thicknesses of oxide films of aluminum foams produced by gas mixtures containing 1.6%-21%oxygen are almost the same.The reasons why the thickness of oxide film nearly does not change with the variation of oxygen content and the amount of oxygen needed to achieve 100%coverage of oxide film are both discussed.In addition,the role of oxide film on bubble surface in foam stability is also analyzed.展开更多
To improve the oxidation resistance of boron-modified carbon foams, the B2O3 coating was prepared on boron-modified carbon foams by low-cost slurry method. The microstructures and phase compositions of the coated carb...To improve the oxidation resistance of boron-modified carbon foams, the B2O3 coating was prepared on boron-modified carbon foams by low-cost slurry method. The microstructures and phase compositions of the coated carbon foams were characterized by scanning electron microscopy and X-ray diffraction, respectively. Oxidation resistances of uncoated and coated boron-modified carbon foams were investigated at 873 K in air. The results showed that as-received B2O3 coating could protect boron-modified carbon foams from oxidation at 873 K. B2O3-coated carbon foam doped with 7% B2O3 （mass fraction） （BO-7） had better oxidation resistance, exhibiting mass loss of 17.40% after oxidation at 873 K for 120 min. The melting glass layer formed on the surface of BO-7 could prevent oxygen from diffusing into boron-modified carbon foams substrate during oxidation to some extent.展开更多
A new method of testing frother performance was proposed. Four parameters were tested： maximum foam volume, foam half-life, gas-liquid ratio and mean foam rise velocity. Among them the former two parameters indicate ...A new method of testing frother performance was proposed. Four parameters were tested： maximum foam volume, foam half-life, gas-liquid ratio and mean foam rise velocity. Among them the former two parameters indicate frother＇s foaming ability and foam stability respectively, and the latter two indicate water carrying ability and foam viscosity, respectively. The performance of four frothers in a two-phase （solution-air） system was tested and batch flotation tests on a copper ore were carried out. By analyzing frother performance in a two-phase system and comparing with the flotation results, correlation between them was found. Higher-copper concentrate grade was obtained by frothers with weak water carrying ability and low foam viscosity. And frothers with strong foaming ability and stable foam tend to obtain higher copper recovery.展开更多
[Objective]The aim of this study was to explore the feasibility of three kinds of urea formaldehyde foam substrate in tall fescue establishment as well as to study on evaluation of turf quality.[Method]The visual esti...[Objective]The aim of this study was to explore the feasibility of three kinds of urea formaldehyde foam substrate in tall fescue establishment as well as to study on evaluation of turf quality.[Method]The visual estimates,ecological quality estimates and utility quality estimates were used as the 1st level indicators,and the density,color,texture,uniformity,green period,cover degree,biomass,emergence energy,growth rate and turf-forming time were used as the corresponding 2nd level indicators.With T.L.Satty＇s method Analytic Hierarchy Process（AHP） and the fuzzy synthesis evaluation method,the weight ratio of matrix was obtained and the synthetic evaluation result was accorded with facts,then it could be regarded as the satisfying value of weight.[Result]The quality of three covering soil treatments was better than that of uncovering treatment and conventional treatment,the quality synthetic evaluation of F1 was the best,which was about 0.770.[Conclusion]Urea formaldehyde foam substrate showed high quality for turf establishment,which could be further spread and applied.展开更多
By using GARCH（1,1）-M and EGARCH（1,1）-M models, the relationships among funds speculation transaction, arbitrage transaction and the fluctuation of international copper future price were studied. The news impact c...By using GARCH（1,1）-M and EGARCH（1,1）-M models, the relationships among funds speculation transaction, arbitrage transaction and the fluctuation of international copper future price were studied. The news impact curve of copper future price fluctuation respectively introduced funds speculation position and arbitrage position was given, and the result is consistent with the empirical study conclusion. The results show that investment funds are not the factor that causes copper future price fluctuation, but can reduce the copper future price fluctuation; the copper future price fluctuation is more sensitive to negative information, and ftmd speculative positions can reduce asymmetric effect of copper price fluctuation, while fimds arbitrage position influences less.展开更多
In the range of 620？710 °C, air was blown into A356 aluminum alloy melt to produce aluminum foams. In order to study the influence of temperature on the thickness of oxide film on bubble surface, Auger electron ...In the range of 620？710 °C, air was blown into A356 aluminum alloy melt to produce aluminum foams. In order to study the influence of temperature on the thickness of oxide film on bubble surface, Auger electron spectroscopy （AES） was used. Based on the knowledge of corrosion science and hydrodynamics, two oxidation kinetics models of oxide film on bubble surface were established. The thicknesses of oxide films produced at different temperatures were predicted through those two models. Furthermore, the theoretical values were compared with the experimental values. The results indicate that in the range of 620？710 °C, the theoretical values of the thickness of oxide film predicted by the model including the rising process are higher than the experimental values. While, the theoretical values predicted by the model without the rising process are in good agreement with the experimental values, which shows this model objectively describes the oxidation process of oxide film on bubble surface. This work suggests that the oxidation kinetics of oxide film on bubble surface of aluminum foams produced by gas injection foaming process follows the Arrhenius equation.展开更多
A two-dimensional and two-phase numerical model is presented for the smolder propagation in a horizontal polyurethane foam. The chemical processes considered include endothermic pyrolysis and exotherrnic oxidation deg...A two-dimensional and two-phase numerical model is presented for the smolder propagation in a horizontal polyurethane foam. The chemical processes considered include endothermic pyrolysis and exotherrnic oxidation degradation of polyurethane foam and exothermic oxidation of char. The governing equations are discretized in space using the finite element method and solved by the software package FEMLAB. Predicted profiles of solid temperature as well as evolutions of solid compositions （including foam, char and ash） are presented at an airflow velocity of 0. 28 cm/s. The computed average smoldering velocity is 0. 021 4 cm/s, and the average maximum temperature is 644. 67 K. Based on the evolutions of solid compositions, the packed bed can be obviously divided into four zones： unreacted zone, fuel pyrolysis and oxidation zone, char oxidation zone and fuel burned-out zone. Simultaneously, the effects of inlet air velocity and fuel properties （including thermal conductivity, specific heat, density and pore diameter） are studied on the smoldering propagation. The results show that the smoldering velocity and temperature have a roughly linear increase with increasing inlet air velocity; the fuel density is the most important factor in determining smoldering propagation; radiation has a non-negligible role on the smoldering velocity for larger pore diameters of porous material. The computational results are compared with the experimental data and a general agreement is reached.展开更多
文摘Graphitized carbon foams(GFms)were prepared using mesophase pitch(MP)as a raw material by foaming(450℃),pre-oxidation(320℃),carbonization(1000℃)and graphitization(2800℃).The differences in structure and properties of GFms prepared from different MP precursors pretreated by ball milling or liquid phase extraction were investigated and compared,and semi-quantitative calculations were conducted on the Raman and FTIR spectra of samples at each preparation stage.Semi-quantitat-ive spectroscopic analysis provided detailed information on the structure and chemical composition changes of the MP and GFm de-rived from it.Combined with microscopic observations,the change from precursor to GFm was analyzed.The results showed that ball milling concentrated the distribution of aromatic molecules in the pitch,which contributed to uniform foaming to give a GFm with a uniform pore distribution and good properties.Liquid phase extraction helped remove light components while retaining large aromatics to form graphitic planes with the largest average size during post-treatment to produce a GFm with the highest degree of graphitization and the fewest open pores,giving the best compression resistance(2.47 MPa),the highest thermal conductivity(64.47 W/(m·K))and the lowest electrical resistance(13.02μΩ·m).Characterization combining semi-quantitative spectroscopic ana-lysis with microscopic observations allowed us to control the preparation of the MP-derived GFms.
基金Project (2004AA33G060) supported by the National High-tech Research and Development Program of China
文摘Aluminum foams were fabricated by melt-based route using ZrH2 as a foaming agent. The factors which affected the foaming of aluminum foams during casting process were investigated. The powdered zirconium hydride with content of 0.6%-1.4% （mass fraction） was added to the molten pure aluminum and the foaming condition was controlled in a temperature range from 933 to 1 013 K, Ca amount of 1.5%-3.0% （mass fraction）, stirring time of 0.5-2.5 min and holding time of 1.5-4.0 min to obtain homogeneous aluminum foams. The fabricated aluminum foams were characterized by XRD, SEM and Image-pro plus. The mechanical properties of the aluminum foams with different relative density were tested. The result indicates that the foaming agent （ZrH2） is suitable for the preparation of small aperture aluminum foams with average pore diameter of 1 mm. Inter-metallic compounds and Al2O3 have effect on the melt viscosity. The aluminum foams experience linear elastic, platforms and densification process and had a higher efficiency of energy absorption.
基金Projects(U1332110,50704012)supported by the National Natural Science Foundation of ChinaProject(F10-205-1-59)supported by Science and Technology Foundation of Shenyang,China
文摘Static three-point bending tests of aluminum foam sandwiches with glued steel panel were performed. The deformation and failure of sandwich structure with different thicknesses of panel and foam core were investigated. The results indicate that the maximum bending load increases with the thickness of both steel panel and foam core. The failure of sandwich can be ascribed to the crush and shear damage of foam core and the delamination of glued interface at a large bending load, The crack on the foam wall developed in the melting foam procedure is the major factor for the failure of foam core. The sandwich structure with thick foam core and thin steel panel has the optimal specific bending strength. The maximum bending load of that with 8 mm panel and 50 mm foam core is 66.06 kN.
基金Projects (90716005, 10802055, 10972153) supported by the National Natural Science Foundation of ChinaProject (2007021005) supported by the Natural Science Foundation of Shanxi Province, China+2 种基金Project supported by the Postdoctoral Science Foundation of ChinaProject supported by the Homecomings Foundation, ChinaProject supported by the Top Young Academic Leaders of Higher Learning Institutions of Shanxi, China
文摘A multi-parameter nonlinear elasto-plastic constitutive model which can fully capture the three typical features of stress-strain response, linearity, plasticity-like stress plateau and densification phases was developed. The functional expression of each parameter was determined using uniaxial compression tests for aluminum alloy foams. The parameters of the model can be systematically varied to describe the effect of relative density which may be responsible for the changes in yield stress and hardening-like or softening-like behavior at various strain rates. A comparison between model predictions and experimental results of the aluminum alloy foams was provided to validate the model. It was proved to be useful in the selection of the optimal-density and energy absorption foam for a specific application at impact events.
文摘The two kinds of rigid polyurethane （PU） foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in weight. The indexes of mechanical performance, apparent density, thermal stability and aging resistance were separately tested for the prepared PU foams. The results show that the mechanical property, thermal insulation and thermal stability for PU foam with modified alkali lignin are excellent among two kinds of PU foams and control samples. The additions of the refined alkali lignin and modified alkali lignin to PU foam have little effect on the natural aging or heat aging resistance except for decreasing hot alkali resistance apparently. Additionally, the thermal conductivity of modified alkali lignin PU foam is lowest among two kinds of PU foams and control samples. The alkali lignin PU foam modified by 3-chloro-1,2-epoxypropane could be applied in the heat preservation field.
基金Project(51371104)supported by the National Natural Science Foundation of China
文摘Based on A356 aluminum alloy,aluminum foams were prepared by gas injection foaming process with pure nitrogen,air and some gas mixtures.The oxygen volume fraction of these gas mixtures varied from 0.2%to 8.0%.Optical microscopy,scanning electron microscopy（SEM） and Auger electron spectroscopy（AES） were used to analyze the influence of oxygen content on cell structure,relative density,macro and micro morphology of cell walls,coverage area fraction of oxide film,thickness of oxide film and other aspects.Results indicate that the coverage area fraction of oxide film on bubble surface increases with the increase of oxygen content when the oxygen volume is less than 1.2%.While when the oxygen volume fraction is larger than 1.6%,an oxide film covers the entire bubble surface and aluminum foams with good cell structure can be produced.The thicknesses of oxide films of aluminum foams produced by gas mixtures containing 1.6%-21%oxygen are almost the same.The reasons why the thickness of oxide film nearly does not change with the variation of oxygen content and the amount of oxygen needed to achieve 100%coverage of oxide film are both discussed.In addition,the role of oxide film on bubble surface in foam stability is also analyzed.
基金Projects(51072107,51272213,51221001)supported by the National Natural Science Foundation of ChinaProject(B08040)supported by the Program of Introducing Talents of Discipline to Universities of China("111" Project)
文摘To improve the oxidation resistance of boron-modified carbon foams, the B2O3 coating was prepared on boron-modified carbon foams by low-cost slurry method. The microstructures and phase compositions of the coated carbon foams were characterized by scanning electron microscopy and X-ray diffraction, respectively. Oxidation resistances of uncoated and coated boron-modified carbon foams were investigated at 873 K in air. The results showed that as-received B2O3 coating could protect boron-modified carbon foams from oxidation at 873 K. B2O3-coated carbon foam doped with 7% B2O3 （mass fraction） （BO-7） had better oxidation resistance, exhibiting mass loss of 17.40% after oxidation at 873 K for 120 min. The melting glass layer formed on the surface of BO-7 could prevent oxygen from diffusing into boron-modified carbon foams substrate during oxidation to some extent.
基金Project(51174229)supported by the National Natural Science Foundation of China
文摘A new method of testing frother performance was proposed. Four parameters were tested： maximum foam volume, foam half-life, gas-liquid ratio and mean foam rise velocity. Among them the former two parameters indicate frother＇s foaming ability and foam stability respectively, and the latter two indicate water carrying ability and foam viscosity, respectively. The performance of four frothers in a two-phase （solution-air） system was tested and batch flotation tests on a copper ore were carried out. By analyzing frother performance in a two-phase system and comparing with the flotation results, correlation between them was found. Higher-copper concentrate grade was obtained by frothers with weak water carrying ability and low foam viscosity. And frothers with strong foaming ability and stable foam tend to obtain higher copper recovery.
基金Supported by Beijing Excellent Talent Training Project(20071D020500055)Beijing Municipal Academy of Agricultural Youth Foundation of China(2007020414)+1 种基金Beijing Municipal Science and Technology Commission of Township Building Based onan Innovative New Agricultural Technology Research and Demonstration(Z080005032508024)Slow-release Fertilizer TechnologyResearch Project(2008BAD4B04)~~
文摘[Objective]The aim of this study was to explore the feasibility of three kinds of urea formaldehyde foam substrate in tall fescue establishment as well as to study on evaluation of turf quality.[Method]The visual estimates,ecological quality estimates and utility quality estimates were used as the 1st level indicators,and the density,color,texture,uniformity,green period,cover degree,biomass,emergence energy,growth rate and turf-forming time were used as the corresponding 2nd level indicators.With T.L.Satty＇s method Analytic Hierarchy Process（AHP） and the fuzzy synthesis evaluation method,the weight ratio of matrix was obtained and the synthetic evaluation result was accorded with facts,then it could be regarded as the satisfying value of weight.[Result]The quality of three covering soil treatments was better than that of uncovering treatment and conventional treatment,the quality synthetic evaluation of F1 was the best,which was about 0.770.[Conclusion]Urea formaldehyde foam substrate showed high quality for turf establishment,which could be further spread and applied.
基金Project(20090162120086) supported by Research Fund for the Doctoral Program of Higher Education of ChinaProject(10YJCZH123) supported by Humanity and Social Science Foundation of Ministry of Education of China+2 种基金Project(12JJ4077) supported by the National Natural Science Foundation of Hunan Province of ChinaProject(2009ZK3053) supported by Soft Science Research Project of Hunan Province of ChinaProject supported by the Freedom Explore Program of Central South University,China
文摘By using GARCH（1,1）-M and EGARCH（1,1）-M models, the relationships among funds speculation transaction, arbitrage transaction and the fluctuation of international copper future price were studied. The news impact curve of copper future price fluctuation respectively introduced funds speculation position and arbitrage position was given, and the result is consistent with the empirical study conclusion. The results show that investment funds are not the factor that causes copper future price fluctuation, but can reduce the copper future price fluctuation; the copper future price fluctuation is more sensitive to negative information, and ftmd speculative positions can reduce asymmetric effect of copper price fluctuation, while fimds arbitrage position influences less.
基金Project(51371104)supported by the National Nature Science Foundation of China
文摘In the range of 620？710 °C, air was blown into A356 aluminum alloy melt to produce aluminum foams. In order to study the influence of temperature on the thickness of oxide film on bubble surface, Auger electron spectroscopy （AES） was used. Based on the knowledge of corrosion science and hydrodynamics, two oxidation kinetics models of oxide film on bubble surface were established. The thicknesses of oxide films produced at different temperatures were predicted through those two models. Furthermore, the theoretical values were compared with the experimental values. The results indicate that in the range of 620？710 °C, the theoretical values of the thickness of oxide film predicted by the model including the rising process are higher than the experimental values. While, the theoretical values predicted by the model without the rising process are in good agreement with the experimental values, which shows this model objectively describes the oxidation process of oxide film on bubble surface. This work suggests that the oxidation kinetics of oxide film on bubble surface of aluminum foams produced by gas injection foaming process follows the Arrhenius equation.
基金The National Natural Science Foundation of China(No50476073)
文摘A two-dimensional and two-phase numerical model is presented for the smolder propagation in a horizontal polyurethane foam. The chemical processes considered include endothermic pyrolysis and exotherrnic oxidation degradation of polyurethane foam and exothermic oxidation of char. The governing equations are discretized in space using the finite element method and solved by the software package FEMLAB. Predicted profiles of solid temperature as well as evolutions of solid compositions （including foam, char and ash） are presented at an airflow velocity of 0. 28 cm/s. The computed average smoldering velocity is 0. 021 4 cm/s, and the average maximum temperature is 644. 67 K. Based on the evolutions of solid compositions, the packed bed can be obviously divided into four zones： unreacted zone, fuel pyrolysis and oxidation zone, char oxidation zone and fuel burned-out zone. Simultaneously, the effects of inlet air velocity and fuel properties （including thermal conductivity, specific heat, density and pore diameter） are studied on the smoldering propagation. The results show that the smoldering velocity and temperature have a roughly linear increase with increasing inlet air velocity; the fuel density is the most important factor in determining smoldering propagation; radiation has a non-negligible role on the smoldering velocity for larger pore diameters of porous material. The computational results are compared with the experimental data and a general agreement is reached.
