Microstructural evolution and mechanical properties of AZ31 Mg alloy fabricated by a novel bifurcation-equal channel angular pressing

In this work,a novel type of short-process deformation technology of Mg alloys,bifurcation-equal channel angular pressing(B-ECAP),was proposed to refine grain and improve the basal texture.The cylindrical billets were first compressed into the die cavity,then sequentially flowed downward through a 90°corner and two 120°shear steps.The total strain of B-ECAP process could reach 3.924 in a single pass.The results of microstructure observation showed that DRX occurred at upsetting process in the die cavity and completed at position D.The grains were refined to 6.3μm at being extruded at 300℃ and grew obviously with the extrusion temperature increase.The shear tress induced by 900 corner and two 120°shear steps resulted in the basal poles of most grains tilted to extrusion direction(ED)by±25°.Compared with the original billets,the extruded sheets exhibited higher yield strengths(YS),which was mainly attributed to the grain refinement.The higher Schmid factor caused by ED-tilt texture resulted in a fracture elongation(FE)more than that of the original bar in ED,while was equivalent to that in transverse direction(TD).As the extrusion temperature increased,the variation of UTS and YS in ED and TD decreased gradually without ductility obviously decrease.

转角

生命面前从来都不会总是平坦的道路。正如明月不会总是圆满地悬挂在夜空，也许一切都在没有规律地运转。在不可知的未来我们会经历什么？我想不管是失意还是得意，都不能失去我们最初的梦想和勇气。要豪情满怀地去迎接明天的灿烂阳光!

Astronomic background of global huge earthquakes at beginning of 21st century

Since the beginning of the 21st century,major earthquakes have frequently occurred worldwide.To explore the impact of astronomical factors on earthquakes,in this study,the statistical analysis method of correlation is used to systematically analyze the effects of astronomical factors,such as solar activity,Earth’s rotation,lunar declination angle,celestial tidal force,and other phenomena on M≥8 global earthquakes at the beginning of the 21st century.With regard to solar activity,this study focuses on the analysis of the 11-year and century cycles of solar activity.The causal relationship of the Earth’s rotation is not obvious in this work and previous works;in contrast,the valley period of the solar activity century cycle may be an important astronomical factor leading to the frequent occurrence of global earthquakes at the beginning of the 21st century.This topic warrants further study.

转角遇见我的影子

“咱俩玩儿踩影子的游戏吧!”“好啊!”我和老弟在路灯下玩儿。“咦，老姐，你的影子呢？”老弟突然惊奇地大叫起来。“别吓我了，不是在前……哎呀。我的影子呢？”坏了坏了，这影子怎么会失踪呢？

转角，邂逅天使

转角，在人生里有许多个。天使呢？也许，转过头你就会发现天使。其实，天使一直在身后微笑。天使在人间，只是粗心的我们没有发现而已吧。

转角遇见幸福

又跟老妈吵架了。我赌气地走在巷子里．每一步都在狠狠地跺脚。 走到了岔路口，我向左拐去，转角遇到了幸福。

转角遇到这只“猪”

看了这个题目．很多人会笑到肚子都痛了。但我要说的故事又何止是题目这几个字就能讲清楚的。在这只“猪”到来之前，我的生活简直可以与皇帝媲美。

转角的阳光

一缕阳光透过窗户，将斑驳的身影投射在转角。一朵微笑的栀子花素雅地开着，清香而悠远，将一份心的宁静渲染。点点金光在花蕊里跳跃，像点点摇曳的烛光，闪烁间将心中的一份希望点燃。

主动脉夹层,比心梗更“凶”

2020年,曾出演热播电视剧《转角遇到爱》的36岁台湾艺人黄鸿升猝然离世,让人愕然。其经纪人对外公布称,黄鸿升因主动脉剥离,造成血管堵塞,摔倒在浴室里,被发现时已离世。这种病,又称“主动脉夹层”。主动脉夹层为何如此凶险?能够预防吗?

Effect of equal-channel angular pressing and aging on corrosion behavior of ZK60 Mg alloy

Commercial ZK60 Mg alloy was processed by multi-pass equal-channel angular pressing（ECAP） and subsequent aging to investigate the effect of grain refinement and second-phase redistribution on its corrosion behavior. Electrochemical tests show that the fine-grained samples after more ECAP passes have higher corrosion current densities（Jcorr） in the polarization curves, lower charge-transfer resistance（Rt） values in the EIS plots. The severe plastic deformation decreases the alloy corrosion resistance besides the well-known strengthening and toughening. Scanning Kelvin probe（SKP） measurement shows that the anodic and cathode sites are homogeneously distributed on the surface of the fine-grained alloy, which inhibits localized corrosion. The SKP potential, having linear relationship with the corrosion potential（φcorr）, decreases with increasing the ECAP pass. Furthermore, the post-ECAP aging can slightly improve the corrosion resistance of the fine-grained ZK60 Mg alloy and enhance the comprehensive performances, due to the stress relief and uniform distribution of second-phase particles.

Aging behavior and mechanical properties of 6013 aluminum alloy processed by severe plastic deformation

Structural features, aging behavior, precipitation kinetics and mechanical properties of a 6013 Al–Mg–Si aluminum alloy subjected to equal channel angular pressing （ECAP） at different temperatures were comparatively investigated with that in conventional static aging by quantitative X-ray diffraction （XRD） measurements, differential scanning calorimetry （DSC） and tensile tests. Average grain sizes measured by XRD are in the range of 66-112 nm while the average dislocation density is in the range of 1.20×10^14-1.70×10^14 m^-2 in the deformed alloy. The DSC analysis reveals that the precipitation kinetics in the deformed alloy is much faster as compared with the peak-aged sample due to the smaller grains and higher dislocation density developed after ECAP. Both the yield strength （YS） and ultimate tensile strength （UTS） are dramatically increased in all the ECAP samples as compared with the undeformed counterparts. The maximum strength appears in the samples ECAP treated at room temperature and the maximum YS is about 1.6 times that of the statically peak-aged sample. The very high strength in the ECAP alloy is suggested to be related to the grain size strengthening and dislocation strengthening, as well as the precipitation strengthening contributing from the dynamic precipitation during ECAP.

Large-scale manufacturing of aluminum alloy plate extruded from subsize billet by new porthole-equal channel angular processing technique

To manufacture plate by the combination of equal channel angular processing （ECAP） and porthole die extrusion techniques, a novel technique, namely portholes-equal channel angular processing （P-ECAP）, was studied. Extrusion of AL6005A plate used for the bullet train plate was investigated by finite element method. The relevant porthole dies involving ECAP technique in channels were designed. Dimensional changes in the scrap part of the extrudate obtained after extrusion from the P-ECAP die, with different channel angles, were predicted. Effects of the channel angle and extrusion speed on the maximum temperature of the workpiece and other field variables were evaluated. At the channel angle of 160° of P-ECAP dies, the extrudate exhibited the optimal performance and the least amount of extrudate scrap was obtained. The optimal extrusion speed was 3-5 mm/s. Moreover, with the increase in ram speed from 1 to 9 mm/s, the peak extrusion load increased by about 49% and the maximum temperature was increased by about 70 ℃. The effective strain exhibited ascending trend in the comer of the ECAP deformation zone. In the solder seam and the side of die bearing of extrudate, the maximum principal stresses were tensile stress.

Equal channel angular extrusion of NiTi shape memory alloy tube

As a new attempt, equal channel angular extrusion （ECAE） of nickel-titanium shape memory alloy （NiTi SMA） tube was investigated by means of process experiment, finite element method （FEM） and microscopy. NiTi SMA tube with the steel core in it was inserted into the steel can during ECAE of NiTi SMA tube. Based on rigid-viscoplastic FEM, multiple coupled boundary conditions and multiple constitutive models were used for finite element simulation of ECAE of NiTi SMA tube, where the effective stress field, the effective strain field and the velocity field were obtained. Finite element simulation results are in good accordance with the experimental ones. Finite element simulation results reveal that the velocity field shows the minimum value in the corner of NiTi SMA tube, where severe shear deformation occurs. Microstructural observation results reveal that severe plastic deformation leads to a certain grain orientation as well as occurrence of substructures in the grain interior and dynamic recovery occurs during ECAE of NiTi SMA tube. ECAE of NiTi SMA tube provides a new approach to manufacturing ultrafine-grained NiTi SMA tube.

Strain rate-dependent high temperature compressive deformation characteristics of ultrafine-grained pure aluminum produced by ECAP

To explore the effect of strain rate ε on the high temperature deformation characteristics of ultrafine-grained materials, the deformation and damage features as well as microstructures of ECAP-treated pure Al at different temperatures T and strain ratesε were systematically studied through compression tests and microscopic observations. The increase in ε eliminates strain softening at T≤473 K, and largely enhances the yield strength and flow stress at 473?573 K. The shear deformation dominates the plastic deformation of ECAP-treated Al. Many cracks along shear bands (SBs) are formed at T≥473 K and secondary SBs basically disappear at 1×10?3 s?1; however, at 1×10?2 s?1, cracks are only observed at temperature below 473 K, and secondary SBs become clearer at T≥473 K. The microstructures of ECAP-treated Al mainly consist of sub-grains (SGs). The increase in ε inhibits the SG growth, thus leading to the increases both in yield strength and flow stress at high temperatures.

Effect of processing route on grain refinement in pure copper processed by equal channel angular extrusion

An experimental study of the microstructures in pure copper billets processed by 8 passes of equal channel angular extrusion （ECAE） via an extended range of processing routes with a 90° die is carried out. Each processing route is defined according to the inter-pass billet rotation angle （χ）, which varies from 0° to 180°. According to the generation of high-angle boundaries and reduction of grain size by electron backscatter diffraction （EBSD） measurements, the grain refinement is found to be most efficient for route with χ=90°and least efficient with χ=180°, among the seven routes studied. This trend is supported by supplementary transmission electron microscopy （TEM） measurements. Comparison of the EBSD and TEM data reveals the importance of considering the non-equiaxity of grain structures in quantitative assessment of microstructural differences in ECAE-processed materials.

Application of crystal plasticity modeling in equal channel angular extrusion

Some applications of crystal plasticity modeling in equal channel angular extrusion（ECAE） of face-centered cubic metals were highlighted.The results show that such simulations can elucidate the dependency of grain refinement efficiency on processing route and the directionality of substructure development,which cannot be explained by theories that consider only the macroscopic deformation behavior.They can also capture satisfactorily the orientation stability and texture evolution under various processing conditions.It is demonstrated that crystal plasticity models are useful tools in exploring the crystallographic nature of grain deformation and associated behavior that are overlooked or sometimes erroneously interpreted by existing phenomenological theories.

Adaptive multicascade attribute reduction based on quantum-inspired mixed co-evolution

Due to the fact that conventional heuristic attribute reduction algorithms are poor in running efficiency and difficult in accomplishing the co-evolutionary reduction mechanism in the decision table, an adaptive multicascade attribute reduction algorithm based on quantum-inspired mixed co-evolution is proposed. First, a novel and efficient self- adaptive quantum rotation angle strategy is designed to direct the participating populations to mutual adaptive evolution and to accelerate convergence speed. Then, a multicascade model of cooperative and competitive mixed co-evolution is adopted to decompose the evolutionary attribute species into subpopulations according to their historical performance records, which can increase the diversity of subpopulations and select some elitist individuals so as to strengthen the sharing ability of their searching experience. So the global optimization reduction set can be obtained quickly. The experimental results show that, compared with the existing algorithms, the proposed algorithm can achieve a higher performance for attribute reduction, and it can be considered as a more competitive heuristic algorithm on the efficiency and accuracy of minimum attribute reduction.

Application of Dynamic Track Drawing Algorithm in Ship Monitoring System

The function of dynamic track drawing realized in the ship monitoring system. Based on the function, we could draw the sailing tracks dynamically according to the ship＇s orientation. Two kernel algorithms are involved during the system developing process, i.e. the algorithms of angular deflection and distance interval value. The practice of system development shows that the proper application of these two algorithms has good effect＇in the visualization of sailing track.

STUDY OF NON-CONTACT MEASUREMENT OF FREE-FORM SURFACES

A non contact three dimensional measurement method is presented in this paper.This system consists of a laser triangulation probe,a probe head and a coordinate measuring machine (CMM).The measurement principle of the system is discussed,and a system calibration method employing a reference ball is proposed.The geometric model involving four frames is established to calculate the data points based on the reading of the laser probe and position information from the CMM.A measuring experiment for gesso free form surface using this system is carried out.

A Compact Low Energy Electron Microscope for Surface Analysis

The description and function characterization of a flange-on type low energy electron mi- croscope are given. In this microscope a magnetic beam separator with 10° deflection angle is used in order to facilitate compacting the instrument on a single 10 in. flange. Mean- while some correcting elements in the electron optical system are simplified to reduce the complexities of construction and operation. The sample is set close to ground potential, so that all the electrostatic lenses are easily to float at high voltages. The performance of the microscope in typical low energy electron microscopy, low energy electron diffraction and photoemission electron microscopy modes is demonstrated through several experiments. A lateral resolution of 51 nm is estimated for low energy electron microscopy imaging. With femtosecond laser as light source, the consequent nonlinear photoemission makes this micro-scope also suitable for the observation of optical near field phenomena and a lateral resolution of 110 nm is obtained.