在理性与感性间游走——施万特纳《速率》的音高组织及结构形态

《速率》(Velocities)是当代美国作曲家约瑟夫·施万特纳(Joseph Schwantner,b, 1943)于1990年创作的马林巴独奏作品。其创作风格不同于浪漫主义以传统调性与和声功能为基础;也不同于现代主义过分抽象、理智、严格控制的音乐风格,而是通过对音高组织的设计运用将调性与非调性因素并置体现在结构中,形成了施式的"折中主义"风格。从20世纪70年代初期至今,施万特纳一直在他的作品中探索新的创作技法和风格,本文关注的是其在20世纪90年代所创作的作品中对音高组织的设计运用及结构布局。

Effect of quenching cooling rate on residual stress and microstructure evolution of 6061 aluminum alloy

In this study,the cooling rate was manipulated by quenching with water of different temperatures(30,60 and 100℃).Surface and internal residual stresses in the quenched 6061 aluminum alloy samples were measured using hole-drilling and crack compliance methods,respectively.Then,the processability of the quenched samples was evaluated at cryogenic temperatures.The mechanical properties of the as-aged samples were assessed,and microstructure evolution was analyzed.The surface residual stresses of samples W30℃,W60℃and W100℃is−178.7,−161.7 and−117.2 MPa,respectively along x-direction,respectively;and−191.2,−172.1 and−126.2 MPa,respectively along y-direction.The sample quenched in boiling water displaying the lowest residual stress(~34%and~60%reduction in the surface and core).The generation and distribution of quenching residual stress could be attributed to the lattice distortion gradient.Desirable plasticity was also exhibited in the samples with relatively low quenching cooling rates at cryogenic temperatures.The strengthes of the as-aged samples are 291.2 to 270.1 MPa as the quenching water temperature increase from 30℃to 100℃.Fine and homogeneous β"phases were observed in the as-aged sample quenched with boiling water due to the clusters and Guinier-Preston zones(GP zones)premature precipitated during quenching process.

Load-bearing characteristics and energy evolution of fractured rock masses after granite and sandstone grouting

Experiments on grouting-reinforced rock mass specimens with different particle sizes and features were carried out in this study to examine the effects of grouting reinforcement on the load-bearing characteristics of fractured rock mass.The strength and deformation features of grouting-reinforced rock mass were analyzed under different loading manners;the energy evolution mechanism of grouting-reinforced rock mass specimens with different particle sizes and features was investigated;the energy dissipation ratio and post-peak stress decreasing rate were employed to evaluate the bearing stability of grouting-reinforced rock mass.The results show that the strength and ductility of granite-reinforced rock mass(GRM)under biaxial loading are higher than that of sandstone-reinforced rock mass(SRM)under uniaxial loading.Besides,the energy evolution characteristics of grouting-reinforced rock mass under uniaxial and biaxial loading mainly could be divided into early,middle,and late stages.In the early stage,total,elastic,and dissipation energies were quite small with flatter curves;in the middle stage,elastic energy increased rapidly,whereas dissipation energy increased slowly;in the late stage,dissipation energy increased sharply.The energy dissipation ratio was used to represent the pre-peak plastic deformation.Under uniaxial loading,this ratio increased as the particle size increased and the pre-peak plastic deformation of grouting-reinforced rock mass became larger;under biaxial loading,it dropped as the particle size increased,and the pre-peak plastic deformation of grouting-reinforced rock mass became smaller.The post-peak stress decline rate A_(v) was used to assess the post-peak bearing performance of grouting-reinforced rock mass.Under uniaxial loading,parameter A_(v) exhibited reduction as the particle size kept increasing,and the ability of post-peak of grouting-reinforced rock mass to allow deformation development was greater,and the bearing capacity was greater;under biaxial loading,A_(v) increased with the particle size,and the ability of post-peak of grouting-reinforced rock mass to allow deformation development was low and the bearing capacity was reduced.The findings are considered instrumental in improving the stability of the roadway-surrounding rock by granite and sandstone grouting.

Recent Advances on Ruthenium-based Electrocatalysts for Lithium-oxygen Batteries

Rechargeable lithium-oxygen(Li-O_(2))batteries have attracted wide attention due to their high energy density.However,the sluggish cathode kinetics results in high overvoltage and poor cycling performance.Ruthenium(Ru)-based electrocatalysts have been demonstrated to be promising cathode catalysts to promote oxygen evolution reaction(OER).It facilitates decomposition of lithium peroxide(Li_(2)O_(2))by adjusting Li_(2)O_(2) morphologies,which is due to the strong interaction between Ru-based catalyst and superoxide anion(O_(2))intermediate.In this review,the design strategies of Ru-based electrocatalysts are introduced to enhance their OER catalytic kinetics in Li-O_(2) batteries.Different configurations of Ru-based catalysts,including metal particles(Ru metal and alloys),single-atom catalysts,and Ru-loaded compounds with various substrates(carbon materials,metal oxides/sulfides),have been summarized to regulate the electronic structure and the matrix architecture of the Ru-based electrocatalysts.The structure-property relationship of Ru-based catalysts is discussed for a better understanding of the Li_(2)O_(2) decomposition mechanism at the cathode interface.Finally,the challenges of Ru-based electrocatalysts are proposed for the future development of Li-O_(2) batteries.

Rate Law for Photoelectrochemical Water Splitting Over CuO

Photocatalytic splitting of water over p-type semiconductors is a promising strategy for production of hydrogen.However,the determination of rate law is rarely reported.To this purpose,copper oxide(CuO)is selected as a model photocathode in this study,and the photogenerated surface charge density,interfacial charge transfer rate constant and their relation to the water reduction rate(in terms of photocurrent)were investigated by a combination of(photo)electrochemical techniques.The results showed that the charge transfer rate constant is exponential-dependent on the surface charge density,and that the photocurrent equals to the product of the charge transfer rate constant and surface charge density.The reaction is first-order in terms of surface charge density.Such an unconventional rate law contrasts with the reports in literature.The charge density-dependent rate constant results from the Fermi level pinning(i.e.,Galvani potential is the main driving force for the reaction)due to accumulation of charge in the surface states and/or Frumkin behavior(i.e.,chemical potential is the main driving force).This study,therefore,may be helpful for further investigation on the mechanism of hydrogen evolution over a CuO photocathode and for designing more efficient CuO-based photocatalysts.

A Hybrid Compensation Scheme for the Input Rate-Dependent Hysteresis of the Piezoelectric Ceramic Actuators

A hybrid compensation scheme for piezoelectric ceramic actuators(PEAs)is proposed.In the hybrid compensation scheme,the input rate-dependent hysteresis characteristics of the PEAs are compensated.The feedforward controller is a novel input rate-dependent neural network hysteresis inverse model,while the feedback controller is a proportion integration differentiation(PID)controller.In the proposed inverse model,an input ratedependent auxiliary inverse operator(RAIO)and output of the hysteresis construct the expanded input space(EIS)of the inverse model which transforms the hysteresis inverse with multi-valued mapping into single-valued mapping,and the wiping-out,rate-dependent and continuous properties of the RAIO are analyzed in theories.Based on the EIS method,a hysteresis neural network inverse model,namely the dynamic back propagation neural network(DBPNN)model,is established.Moreover,a hybrid compensation scheme for the PEAs is designed to compensate for the hysteresis.Finally,the proposed method,the conventional PID controller and the hybrid controller with the modified input rate-dependent Prandtl-Ishlinskii(MRPI)model are all applied in the experimental platform.Experimental results show that the proposed method has obvious superiorities in the performance of the system.

Leaching of heavy metals from Dexing copper mine tailings pond

AThe wastewater source of 4# tailing pond in Dexing copper mine consists of alkaline flotation pulp and acid mine drainage （AMD） from the nearby opencast mine. Therefore, the heavy metals in tailing ore are very likely to be released due to acidification from AMD. The leaching behaviors ofZn, Cu, Fe and Mn in mine tailings from Dexing copper mine were investigated by a series of laboratory batch experiments. The effectcs ofpH, temperature, particle size and contact time on the leachability of such heavy metals were examined. It was evident that Zn, Cu, Fe and Mn were major heavy metals in the tailings while gangue minerals like quartz were major constituents in examined tailings. The tailing dissolution reaction was controlled by the acid, whose kinetics could be expressed according to the heterogeneous reaction models and explained by a shrinking core model with the surface chemical reaction as the rate-controlling step. The leachability of all metals examined depended on pH and contact time. The batch studies indicated that the maximum leaching ratios ofZn, Cu, Fe and Mn at pH 2.0 were 5.4%, 5.8%, l 1.1% and 34.1%, respectively. The dissolubility of all metals examined was positively correlated to the temperatures. The particle size would not change dissolution tendency of those heavy metals, but decrease the concentrations of leached heavy metals.

Microwave drying characteristics and kinetics of ilmenite

The microwave drying of ilmenite was investigated.The effects of power levels and sample mass on drying characteristics of moisture content,drying rate,moisture ratio were studied,with microwave power ranging from 119 W to 700 W and sample mass from 5 g to 25 g.The drying processes were completed within 2-8 min at different conditions.The moisture content and drying rates are found to be dramatically affected by microwave power density.For all drying processes the prior microwave absorption of moisture produces an accelerating peak on the drying rate curves in the initial stage.For the sample mass of 25 g and power of 385 W,the drying kinetics were studied.The experimental results fit better to the Henderson-Pabis index model rather than the Page＇s semi-empirical model;the drying rate constant k is increased with the increase of microwave power and decrease of sample mass.

Quench sensitivity and microstructure character of high strength AA7050

The effect of quenching rate on the electrical conductivity and microstructure of thick plates of incumbent AA7050 was investigated by employing Jominy end quench test. The electrical conductivity measurement and microstructural observation were conducted at different distances from the quenched end. The results indicate that the average cooling rates decrease with increasing the distance from the quenched end of the bar in the quench sensitive temperature range. However, the electrical conductivity increases with the increase of distance from the quenched end. The surface parts of the plate were fully recrystallized, while partial recrystallization took place at the quarter and center parts of the plate. The quench induced grain boundary precipitates became remarkably coarser and discontinuously distributed with increasing distance from the quenched end of the bar. Plenty of heterogeneous precipitates were observed to nucleate on A13Zr dispersoids when the distance from the quenched end was greater than 38mm.

Dynamic globularization kinetics during hot working of TA15 titanium alloy with colony microstructure

The dynamic globularization kinetics of TA15（Ti-6Al-2Zr-1Mo-1V） titanium alloy with a colony α microstructure during deformation at temperature range of 860-940 ℃ and strain rate range of 0.01-10 s-1 was quantitatively studied through isothermal compression tests.It is found that the dynamic globularization kinetics and the kinetics rate of TA15 are sensitive to deformation parameters.The dynamic globularized fraction increases with increasing strain,temperature but decreasing strain rate.The variation of globularized fraction with strain approximately follows an Avrami type equation.Using the Avrami type equation,the initiation and completion strains for dynamic globularization of TA15 were predicted to be 0.34-0.59 and 3.40-6.80.The kinetics rate of dynamic globularization increases with strain at first,then decreases.The peak value of kinetics rate,which corresponds to 20%-33% globularization fraction,increases with increasing temperature and decreasing strain rate.

Effects of cooling rate on solution heat treatment of as-cast A356 alloy

The effect of cooling rate of the solidification process on the following solution heat treatment of A356 alloy was investigated,where the cooling rates of 96 K/s and 3 K/s were obtained by the step-like metal mold.Then the eutectic silicon morphology evolution and tensile properties of the alloy samples were observed and analyzed after solution heat treatment at 540 °C for different time.The results show that the high cooling rate of the solidification process can not only reduce the solid solution heat treatment time to rapidly modify the eutectic silicon morphology,but also improve the alloy tensile properties.Specially,it is found that the disintegration,the spheroidization and coarsening of eutectic silicon of A356 alloy are completed during solution heat treatment through two stages,i.e.,at first,the disintegration and spheroidization of the eutectic silicon mainly takes place,then the eutectic silicon will coarsen.

Effect of ruthenium on γ' precipitation behavior and evolution in single crystal superalloys

The effect of Ru on γ＇ precipitation behavior and evolution in single crystal superalloys with different Ru contents were investigated by scanning electron microscopy with energy dispersive spectroscopy,3D atomic probing,differential scanning calorimetry.The results show that the solvus of the γ＇ phase decreases gradually with increasing Ru content in the alloys by casting or by the same solution and aging treatments,the alloy with a larger Ru content yields a smaller γ＇ phase.The addition of Ru increases the growth rate and coarsening rate of the γ＇ phase.Ru mainly distributes in the γ phase,which causes more Re and Mo partition into the γ＇ phase,increasing the absolute value of mismatch and the rafting rate of the γ＇ phase.

Seasonal Changes in Photosynthetic Characteristics of Ammopiptanthus mongolicus

Seasonal changes in the photosynthetic characteristics of Ammopiptantus mongolicus (Maxim. )Chen f. were studied. When the net photosynthetic rate decreased with the elevation of air temperature, thestomatal conductance and stomatal limitation value tended to decline simultaneously, while the interoellularCO2 concentration was increased. According to the two criteria discriminating the stomatal limitation of Photosynthesis suggeSted by Fmrquhar and Sharkey, the seasonal changes in these parameters indicated that the decrease in Pn may not be due to stomatal factor. These studies proved that the relative contents of the large subunit of Rubisco and the photochemical activities correlated with the seasonal changes in the net photosyntheticrate, whieh may show that these two factors contribute primarily to the seasonal changeS in CO2 assimilation.

Effect of as-solidified microstructure on subsequent solution-treatment process for A356 Al alloy

For the compromise of mechanical properties and product cost, the end-chilled sand casting technique was applied to studying the microstructure evolution of A356 Al alloy with cooling rate and the effect of different as-cast microstructures on the subsequent solution-treatment process. The experimental results show that the secondary dendrite arm spacing (SDAS) of primaryα(Al), the size of eutectic Si and the volume fraction of Al?Si eutectic are reduced with increasing the cooling rate. Eutectic Si, subjected to solution treatment at 540 °C for 1 h followed by water quenching to room temperature, is completely spheroidized at cooling rate of 2.6 K/s; is partially spheroidized atcooling rate of 0.6 K/s; and is only edge-rounded at cooling rates of 0.22 and 0.12 K /s. Whilst the microhardness is also the maximum at cooling rate of 2.6 K/s. It consequently suggests that subjected to modification by high cooling rate, the eutectic Si is more readily modified, thus shortening the necessary solution time at given solution temperature, i.e., reducing the product cost.

Temperature variation and solution treatment of high strength AA7050

Temperature variation and solution treatment of high strength aluminum alloy were investigated with temperature data acquisition system,microstructural observation,mechanical properties test,electrical conductivity measurement and differential scanning calorimetry（DSC） analysis.Specimens with two dimensions were employed in the experiment.The results indicate that the specimens with large size undergo low solution temperature and short time,giving rise to the reduction of hardening precipitates.The optimized solution treatments for specimens with dimensions of 25 mm×25 mm×2.5 mm and 70 mm×60 mm×20 mm are（480 ℃,30 min） and（480 ℃,90 min）,respectively.The densities of GP zones and η＇ phases of the small specimen are higher than those of the large specimen,which is consistent with the properties of the alloys.

Effects of cooling rate on microstructure,mechanical and corrosion properties of Mg-Zn-Ca alloy

Mg69Zn27Ca4 alloys with diameters of 1.5, 2 and 3 mm were fabricated using copper mold injection casting method. Microstructural analysis reveals that the alloy with a diameter of 1.5 mm is almost completely composed of amorphous phase. However, with the cooling rate decline, a little α-Mg and MgZn dendrites can be found in the amorphous matrix. Based on the microstructural and tensile results, the ductile dendrites are conceived to be highly responsible for the enhanced compressive strain from 1.3% to 3.1% by increasing the sample diameter from 1.5 mm to 3 mm. In addition, the Mg69Zn27Ca4 alloy with 1.5 mm diameter has the best corrosion properties. The current Mg-based alloys show much better corrosion resistance than the traditionally commercial wrought magnesium alloy ZK60 in simulated sea-water.

Stem Respiration of a Larch (Larix gmelini) Plantation in Northeast China

Stem respiration is an important part of the activity of a tree and is an important source of CO2 evolution from a forest ecosystem. Presently, no standard methods are available for the accurate estimation of total stem CO2 efflux from a forest. In the current study, a 33-year-old (by the year 2001) larch (Larix gmelini Rupr.) plantation was measured throughout 2001-2002 to analyze its monthly and seasonal patterns of stem respiration. Stem respiration rate was also measured at different heights, at different daily intervals and any variation in the larch plantation was recorded. The relationship between stem temperature, growth status and respiration rate was analyzed. Higher respiration rates were recorded in upper reaches of the larch tree throughout the season and these were affected partially by temperature difference. Midday depression was found in the diurnal changes in stem respiration. In the morning, but not in the afternoon, stem respiration was positively correlated with stem temperature. The reason for this variation may be attributed to water deficit, which was stronger in the afternoon. In the larch plantation, a maximum 7-fold variation in stem respiration was found. The growth status (such as mean growth rate of stem and canopy projection area) instead of stem temperature difference was positively correlated with this large variation. An S-model (sigmoid curve) or Power model shows the greatest regression of the field data. In the courses of seasonal and annual changes of stem respiration, peak values were observed in July of both years, but substantial interannual differences in magnitude were observed. An exponential model can clearly show this regression of the temperature-respiration relationship. In our results, Q(10) values ranged from 2.22 in 2001 to 3.53 in 2002. Therefore, estimation of total stem CO2 efflux only by a constant Q(10) value may give biased results. More parameters of growth status and water status should be considered for more accurate estimation.

Influence of strain rate on microstructure and formability of AZ31B magnesium alloy sheets

The effects of strain rate on microstructure and formability of AZ31B magnesium alloy sheets were investigated through uniaxial tensile tests and hemispherical punch tests with strain rates of 10^-4, 10^-3, 10^-2, 10^-1 s^-1 at 200℃. The results show that the volume fraction of dynamic recrystallization grains increases and the original grains are gradually replaced by recrystallization grains with the strain rate decreasing. A larger elongation and a smaller r-value are obtained at a lower strain rate, moreover the erichsen values become larger with the strain rate reducing, so the formability improves. This problem arises in part from the enhanced softening and the coordination of recrystallization grains during deformation.

Photosynthetic Characteristics of Two Superhigh-yield Hybrid Rice

The photosynthetic functions and the sensitivity to photoinhibition were compared between two superhigh_yield hybrid rice (Oryza sativa L.) Liangyoupeijiu and X07S/Zihui 100, the newly developed from two parental lines and traditional hybrid rice Shanyou 63 developed from three parental lines. The results showed that, as compared to Shanyou 63, the net photosynthetic rate of Liangyoupeijiu and X07S/Zihui 100 was 9.1% and 11.9% higher, the transpiration rate was 37.4% and 31.4% lower, and their water use efficiency was 74.2% and 63.5% higher respectively. After strong light (2 000 μmol photons·m -2 ·s -1 ) treatment for 2 h, the photochemical quantum yield and the photochemical quenching increased by 37.0% and 18.0% respectively in Liangyoupeijiu, 28.3% and 46.2% in X07S/Zihui 100, but decreased a little in Shanyou 63. The non_photochemical quenching decreased in Liangyoupeijiu and X07S/Zihui 100 (about 50%) but increased greatly in Shanyou 63 (about 50%). Better photosynthetic functions, higher water use efficiency and stronger resistance to photoinhibition, may be the physiological basis for the super high_yield of the two hybrid rice under study.

Adaptive responses of Acer ginnala, Pyrus ussuriensis and Prunus davidiana seedlings to soil moisture stress

One-year-old seedlings of Amur maple (Acer ginnala Maxim), Ussurian pear (Pyrus ussuriensis Maxim) and David peach (Prunus davidiana Carr) were planted in pots in greenhouse and treated with four different soil moisture contents (75.0%, 61.1%, 46.4% and 35.4%). The results showed that net photosynthesis rate (NPR), transpiration rate (TR) and stomatal conductance (Sc) of seedlings of the three species decreased with the decease of soil moisture content, and Amur maple seedlings had the greatest change in those physiological indices, followed by Ussurian pear, David peach. Amur maple and Ussurian pear seedlings also presented a decrease tendency in water use efficiency (WUE) under lower soil moisture content, whereas this was reversed for David peach. Under water stress the biomass allocation to seedling root had a significant increase for all the experimental species. As to root/shoot ratio, Amur maple seedlings had the biggest increase, while David peach had the smallest increase. The leaf plasticity of Amur maple seedlings was greater, the leaf size and total leaf area decreased significantly as the stress was intensified. No significant change of leaf size and total leaf area was found in seedlings of Ussurian pear and David peach. It was concluded that Amur maple was more tolerant to soil moisture stress in comparison with David peach and Ussurian pear.