Static three-point bending tests of aluminum foam sandwiches with glued steel panel were performed. The deformation and failure of sandwich structure with different thicknesses of panel and foam core were investigated...Static three-point bending tests of aluminum foam sandwiches with glued steel panel were performed. The deformation and failure of sandwich structure with different thicknesses of panel and foam core were investigated. The results indicate that the maximum bending load increases with the thickness of both steel panel and foam core. The failure of sandwich can be ascribed to the crush and shear damage of foam core and the delamination of glued interface at a large bending load, The crack on the foam wall developed in the melting foam procedure is the major factor for the failure of foam core. The sandwich structure with thick foam core and thin steel panel has the optimal specific bending strength. The maximum bending load of that with 8 mm panel and 50 mm foam core is 66.06 kN.展开更多
Two-dimensional plain-weave silicon carbide fiber fabric reinforced silicon carbide(2D-SiC/SiC)composites were molded by stacking method and densified through precursor infiltration and pyrolysis(PIP)process.SiC coati...Two-dimensional plain-weave silicon carbide fiber fabric reinforced silicon carbide(2D-SiC/SiC)composites were molded by stacking method and densified through precursor infiltration and pyrolysis(PIP)process.SiC coating was deposited as the fiber/matrix interphase layer by chemical vapor deposition(CVD)technique.Fiber/matrix debonding and relatively long fiber pullouts were observed on the fracture surfaces.Additionally,the flexural strength and elastic modulus of the composites with and without fiber/matrix interphase layer were investigated using three-point bending test and single-edge notched beam test.The results show that the fiber fraction and the porosity of 2D-SiC/SiC composites with and without coating are 27.2%(volume fraction)and 11.1%,and 40.7%(volume fraction)and 7.5%,respectively.And the flexural strength and elastic modulus of 2D-SiC/SiC composites with and without coating are 363.3 MPa and 127.8 GPa,and 180.2 MPa and 97.2 GPa,respectively.With a proper thickness,the coating can effectively adjust the fiber/matrix interface,thus causing a dramatic increase in the mechanical properties of the composites.展开更多
The author studies the structure of solutions to the interface problems for second order linear elliptic partial differential equations in three space dimension. The set of singular points consists of some singular li...The author studies the structure of solutions to the interface problems for second order linear elliptic partial differential equations in three space dimension. The set of singular points consists of some singular lines and some isolated singular points. It is proved that near a singular line or a singular point, each weak solution can be decomposed into two parts, a singular part and a regular part. The singular parts are some finite sum of particular solutions to some simpler equations, and the regular parts are bounded in some norms, which are slightly weaker than that in the Sobolev space H^2.展开更多
Objective： To evaluate the interface characteristics of the new-designed locking plate （LP） and limited contact-dynamic compression plate （LC-DCP） and compare the fracture healing between LP and LC-DCP in a goat ...Objective： To evaluate the interface characteristics of the new-designed locking plate （LP） and limited contact-dynamic compression plate （LC-DCP） and compare the fracture healing between LP and LC-DCP in a goat tibia fracture model. Methods： Eight-hole LP and LC-DCP were applied to fix fresh goat tibiae in a reproducible manner. The average pressure, force and interface contact area were calculated using Fuji prescale pressure sensitive film interposed among the plate and the bone and image analysis system, Eighthole LP and LC-DCP were applied to each tibia in a goat tibia fracture model. The fracture healing was evaluated by X-ray photography at postoperative 8 weeks. The goats were sacrificed at postoperative 12 weeks. Three-point bending test was conducted in the tibiae. Results： The interface contact of LP system was smaller than that ofLC-DCP （P〈0.05）, while interface contact force of LP system was higher than that of LC-DCP （P〈0.05）. Radiographs revealed that the fracture line disappeared in the LP group, while the fracture line was visible in DCP group at postoperative 8 weeks. At postoperative 12 weeks, the bending strength and bending load of fractured tibia were higher in LP group than in DCP group, respectively.展开更多
基金Projects(U1332110,50704012)supported by the National Natural Science Foundation of ChinaProject(F10-205-1-59)supported by Science and Technology Foundation of Shenyang,China
文摘Static three-point bending tests of aluminum foam sandwiches with glued steel panel were performed. The deformation and failure of sandwich structure with different thicknesses of panel and foam core were investigated. The results indicate that the maximum bending load increases with the thickness of both steel panel and foam core. The failure of sandwich can be ascribed to the crush and shear damage of foam core and the delamination of glued interface at a large bending load, The crack on the foam wall developed in the melting foam procedure is the major factor for the failure of foam core. The sandwich structure with thick foam core and thin steel panel has the optimal specific bending strength. The maximum bending load of that with 8 mm panel and 50 mm foam core is 66.06 kN.
基金Project(NCET-07-0228)support by the New Century Excellent Talents in University
文摘Two-dimensional plain-weave silicon carbide fiber fabric reinforced silicon carbide(2D-SiC/SiC)composites were molded by stacking method and densified through precursor infiltration and pyrolysis(PIP)process.SiC coating was deposited as the fiber/matrix interphase layer by chemical vapor deposition(CVD)technique.Fiber/matrix debonding and relatively long fiber pullouts were observed on the fracture surfaces.Additionally,the flexural strength and elastic modulus of the composites with and without fiber/matrix interphase layer were investigated using three-point bending test and single-edge notched beam test.The results show that the fiber fraction and the porosity of 2D-SiC/SiC composites with and without coating are 27.2%(volume fraction)and 11.1%,and 40.7%(volume fraction)and 7.5%,respectively.And the flexural strength and elastic modulus of 2D-SiC/SiC composites with and without coating are 363.3 MPa and 127.8 GPa,and 180.2 MPa and 97.2 GPa,respectively.With a proper thickness,the coating can effectively adjust the fiber/matrix interface,thus causing a dramatic increase in the mechanical properties of the composites.
文摘The author studies the structure of solutions to the interface problems for second order linear elliptic partial differential equations in three space dimension. The set of singular points consists of some singular lines and some isolated singular points. It is proved that near a singular line or a singular point, each weak solution can be decomposed into two parts, a singular part and a regular part. The singular parts are some finite sum of particular solutions to some simpler equations, and the regular parts are bounded in some norms, which are slightly weaker than that in the Sobolev space H^2.
文摘Objective： To evaluate the interface characteristics of the new-designed locking plate （LP） and limited contact-dynamic compression plate （LC-DCP） and compare the fracture healing between LP and LC-DCP in a goat tibia fracture model. Methods： Eight-hole LP and LC-DCP were applied to fix fresh goat tibiae in a reproducible manner. The average pressure, force and interface contact area were calculated using Fuji prescale pressure sensitive film interposed among the plate and the bone and image analysis system, Eighthole LP and LC-DCP were applied to each tibia in a goat tibia fracture model. The fracture healing was evaluated by X-ray photography at postoperative 8 weeks. The goats were sacrificed at postoperative 12 weeks. Three-point bending test was conducted in the tibiae. Results： The interface contact of LP system was smaller than that ofLC-DCP （P〈0.05）, while interface contact force of LP system was higher than that of LC-DCP （P〈0.05）. Radiographs revealed that the fracture line disappeared in the LP group, while the fracture line was visible in DCP group at postoperative 8 weeks. At postoperative 12 weeks, the bending strength and bending load of fractured tibia were higher in LP group than in DCP group, respectively.
