The hydrodynamic characteristics of a rigid, single, circular cylinder in a three dimensional, incompressible, uniform cross flow were calculated using the large-eddy simulation method of CFX5. Solutions to the three ...The hydrodynamic characteristics of a rigid, single, circular cylinder in a three dimensional, incompressible, uniform cross flow were calculated using the large-eddy simulation method of CFX5. Solutions to the three dimensional N-S equations were obtained by the finite volume method. The focus of this numerical simulation was to research the characteristics of pressure distribution （drag and litt forces） and vortex tubes at high Reynolds numbers. The results of the calculations showed that the forces at every section in the spanwise direction of the cylinder were symmetrical about the middle section and smaller than the forces calculated in two dimensional cases. Moreover, the flow around the cylinder obviously presents three dimensional characteristics.展开更多
In this paper, the numerical predictions of 3D hydrodynamics and power consumption in a vessel stirred by mul- tiple eccentrically located impellers are presented. The vessel is a fiat-bottomed cylindrical one equippe...In this paper, the numerical predictions of 3D hydrodynamics and power consumption in a vessel stirred by mul- tiple eccentrically located impellers are presented. The vessel is a fiat-bottomed cylindrical one equipped with six-curved bladed impellers. Aqueous solutions of xanthan gum are used, which have a shear thinning behavior with yield stress. The influence of several parameters on the mixing efficiency has been investigated, namely： the stirring rate, fluid theology, impeller number and impeller clearance from the tank bottom. Our predicted results are compared with other experimental data and a satisfactory agreement is found.展开更多
This work deals with an application in parametric modeling of problems regarding pipelines buried in static system, written in C＋＋ using ObjectARX functions. The application is fully integrated with AutoCAD through ...This work deals with an application in parametric modeling of problems regarding pipelines buried in static system, written in C＋＋ using ObjectARX functions. The application is fully integrated with AutoCAD through saproms.dll and saproms.arx libraries where the stages of pre-processing, processing and post-processing are done in AutoCAD sotlware environment itself without having to export data to another processing environment. The analysis processing is done by functions whose algorithms are based on the solution of the coupling between the FEM （finite element method） and the BEM （boundary element method）. The representation of the homogeneous pipeline is made by the FEM using a finite element in the form of a cylindrical panel called CYS （cylindrical shell）, developed from the homogeneous isotropic model proposed initially by Djoudi Bahai, who uses the philosophy of the assumed deformation model （assumed strain based model）. The soil is taken to be a continuum infinite or semi-infinite elastic solid patterned by BEM where special boundary elements are proposed with curved surface or curved edges to represent the soil-structure interaction mainly in the areas of contact with the pipeline.展开更多
This paper is concerned with the problem on the global existence and stability of a subsonic flow in an infinitely long cylindrical nozzle for the 3D steady potential flow equation. Such a problem was indicated by Cou...This paper is concerned with the problem on the global existence and stability of a subsonic flow in an infinitely long cylindrical nozzle for the 3D steady potential flow equation. Such a problem was indicated by Courant-Friedrichs in [8, p. 377]： A flow through a duct should be considered as a cal symmetry and should be determined steady, isentropic, irrotational flow with cylindriby solving the 3D potential flow equations with appropriate boundary conditions. By introducing some suitably weighted HSlder spaces and establishing a priori estimates, the authors prove the global existence and stability of a subsonic potential flow in a 3D nozzle when the state of subsonic flow at negative infinity is given.展开更多
The flow and heat transfer characteristics, including transition critical Reynolds number from two-dimensional to three-dimensional, the influence of slit-cylinder geometric parameter on Strouhal number, Nusselt numbe...The flow and heat transfer characteristics, including transition critical Reynolds number from two-dimensional to three-dimensional, the influence of slit-cylinder geometric parameter on Strouhal number, Nusselt number and forces acting on the slit-cylinder are numerically investigated. It's found that transition critical Reynolds number from two-dimensional(flow wake deforms in two directions) to three-dimensional(flow wake deforms in three directions) increases with the augment of the slit width ratio in the range of present considered Reynolds number. The present results indicate that the three-dimensional vortex structures resulting from the deformation of the vortex shedding have significant effects on flow and heat transfer features such as Strouhal number, Nusselt number and forces acting on the cylinders with different ratios of slit width. It's observed that the drag and lift coefficients reduce as the increase of slit width ratio, and vortex shedding is effectively suppressed by the slits.Moreover, the comprehensive heat transfer performance of the cylinder with the slits is significantly improved with the increase of the slit width ratio.展开更多
文摘The hydrodynamic characteristics of a rigid, single, circular cylinder in a three dimensional, incompressible, uniform cross flow were calculated using the large-eddy simulation method of CFX5. Solutions to the three dimensional N-S equations were obtained by the finite volume method. The focus of this numerical simulation was to research the characteristics of pressure distribution （drag and litt forces） and vortex tubes at high Reynolds numbers. The results of the calculations showed that the forces at every section in the spanwise direction of the cylinder were symmetrical about the middle section and smaller than the forces calculated in two dimensional cases. Moreover, the flow around the cylinder obviously presents three dimensional characteristics.
文摘In this paper, the numerical predictions of 3D hydrodynamics and power consumption in a vessel stirred by mul- tiple eccentrically located impellers are presented. The vessel is a fiat-bottomed cylindrical one equipped with six-curved bladed impellers. Aqueous solutions of xanthan gum are used, which have a shear thinning behavior with yield stress. The influence of several parameters on the mixing efficiency has been investigated, namely： the stirring rate, fluid theology, impeller number and impeller clearance from the tank bottom. Our predicted results are compared with other experimental data and a satisfactory agreement is found.
文摘This work deals with an application in parametric modeling of problems regarding pipelines buried in static system, written in C＋＋ using ObjectARX functions. The application is fully integrated with AutoCAD through saproms.dll and saproms.arx libraries where the stages of pre-processing, processing and post-processing are done in AutoCAD sotlware environment itself without having to export data to another processing environment. The analysis processing is done by functions whose algorithms are based on the solution of the coupling between the FEM （finite element method） and the BEM （boundary element method）. The representation of the homogeneous pipeline is made by the FEM using a finite element in the form of a cylindrical panel called CYS （cylindrical shell）, developed from the homogeneous isotropic model proposed initially by Djoudi Bahai, who uses the philosophy of the assumed deformation model （assumed strain based model）. The soil is taken to be a continuum infinite or semi-infinite elastic solid patterned by BEM where special boundary elements are proposed with curved surface or curved edges to represent the soil-structure interaction mainly in the areas of contact with the pipeline.
基金supported by the National Basic Research Program of China (No.2006CB805902)the National Natural Science Foundation of China (No.10871096)the Research Foundation for Advanced Talents of Jiangsu University
文摘This paper is concerned with the problem on the global existence and stability of a subsonic flow in an infinitely long cylindrical nozzle for the 3D steady potential flow equation. Such a problem was indicated by Courant-Friedrichs in [8, p. 377]： A flow through a duct should be considered as a cal symmetry and should be determined steady, isentropic, irrotational flow with cylindriby solving the 3D potential flow equations with appropriate boundary conditions. By introducing some suitably weighted HSlder spaces and establishing a priori estimates, the authors prove the global existence and stability of a subsonic potential flow in a 3D nozzle when the state of subsonic flow at negative infinity is given.
文摘The flow and heat transfer characteristics, including transition critical Reynolds number from two-dimensional to three-dimensional, the influence of slit-cylinder geometric parameter on Strouhal number, Nusselt number and forces acting on the slit-cylinder are numerically investigated. It's found that transition critical Reynolds number from two-dimensional(flow wake deforms in two directions) to three-dimensional(flow wake deforms in three directions) increases with the augment of the slit width ratio in the range of present considered Reynolds number. The present results indicate that the three-dimensional vortex structures resulting from the deformation of the vortex shedding have significant effects on flow and heat transfer features such as Strouhal number, Nusselt number and forces acting on the cylinders with different ratios of slit width. It's observed that the drag and lift coefficients reduce as the increase of slit width ratio, and vortex shedding is effectively suppressed by the slits.Moreover, the comprehensive heat transfer performance of the cylinder with the slits is significantly improved with the increase of the slit width ratio.
