元素的结构分析与元素周期律的不规则性

本文通过对元素周期系中,各元素的结构分析,很方便地找到了对元素的不规则性的解释。

孕产妇输血不规则抗体阳性率的临床调查分析

目的分析本地区孕产妇血清不规则抗体阳性率的最新动态。方法选取我院收诊的420例输血孕产妇作为研究对象,按孕产史及输血史的差别分为A组(2次及以上)和B组(无或小于2次),输血前按输血规范要求进行不规则抗体的检测,统计不规则抗体的阳性率,进一步比较分析A组和B组阳性率的差异。结果 420例输血孕产妇共检出阳性不规则抗体6例,检出率是1.43%,其中有孕产史及输血史A组的阳性率(2.13%)高于无孕产史及输血史B组的阳性率(0.86%)对比差异有统计学意义(P<0.05)。结论孕产妇群体的输血不规抗体阳性率相对普通输血人群要高,且有多次孕产或输血史的不规则抗体的阳性率会更高,因此临床输血对孕产妇群体相关检查需高度重视。

凉山州半细毛羊不同海拔体内寄生虫种类和季节动态的调查研究

凉山半细毛羊是凉山州经过50多年培育而成的,适应二半山区和高寒山区饲养的主要畜种之一,2013年末全州存栏308万只,虽然历年都开展了体内寄生虫驱治措施,取得了一定成效,但是牧户在驱治中的不规范性和驱虫药的相对单一,目前体内寄生虫的感染还是比较严重,有时还会引起大量死亡,造成巨大的经济损失。调查研究凉山半细毛羊体内寄生虫感染种类及季节动态,对制定更加合理的防治措施,有效控制体内寄生虫对凉山半细毛羊的危害。

Irregular seismic data reconstruction based on exponential threshold model of POCS method

Irregular seismic data causes problems with multi-trace processing algorithms and degrades processing quality. We introduce the Projection onto Convex Sets （POCS） based image restoration method into the seismic data reconstruction field to interpolate irregularly missing traces. For entire dead traces, we transfer the POCS iteration reconstruction process from the time to frequency domain to save computational cost because forward and reverse Fourier time transforms are not needed. In each iteration, the selection threshold parameter is important for reconstruction efficiency. In this paper, we designed two types of threshold models to reconstruct irregularly missing seismic data. The experimental results show that an exponential threshold can greatly reduce iterations and improve reconstruction efficiency compared to a linear threshold for the same reconstruction result. We also analyze the anti- noise and anti-alias ability of the POCS reconstruction method. Finally, theoretical model tests and real data examples indicate that the proposed method is efficient and applicable.

Application of Abnormal Touchdown PCR with High Degeneracy Primer in Amplification of Large-Family Genes

[Objective] The aim was to explore the special methods for amplification of large-family genes by using primers with high degeneracy.[Method] By using the primers with high degeneracy,conventional PCR,conventional touchdown PCR and the optimized abnormal touchdown PCR were respectively carried out to amplify the genomic DNA of Cyprinus carpio.[Result] Only one evident electrophoretic band and a few Sox genes were obtained by using normal PCR;no obvious electrophoretic band but dispersive product was obtained by normal touchdown PCR;ideal result was obtained by the abnormal touchdown PCR that three evident electrophoretic bands and much more Sox genes were amplified.[Conclusion] The research provided theoretical basis for the optimization and selection of PCR amplification conditions of the large-family genes.

Ray path of head waves with irregular interfaces

Head waves are usually considered to be the refracted waves propagating along flat interfaces with an underlying higher velocity.However,the path that the rays travel along in media with irregular interfaces is not clear.Here we study the problem by simulation using a new approach of the spectral-element method with some overlapped elements（SEMO） that can accurately evaluate waves traveling along an irregular interface.Consequently,the head waves are separated from interface waves by a time window.Thus,their energy and arrival time changes can be analyzed independently.These analyses demonstrate that,contrary to the case for head waves propagating along a flat interface,there are two mechanisms for head waves traveling along an irregular interface：a refraction mechanism and transmission mechanism.That is,the head waves may be refracted waves propagating along the interface or transmitted waves induced by the waves propagating in the higher-velocity media.Such knowledge will be helpful in constructing a more accurate inversion method,such as head wave travel-time tomography,and in obtaining a more accurate model of subsurface structure which is very important for understanding the formation mechanism of some special areas,such as the Tibetan Plateau.

Research of CRP-based irregular 2D seismic acquisition

Seismic exploration in the mountainous areas of western Chinese is extremely difficult because of the complexity of the surface and subsurface, which results in shooting difficulties, seismic data with low signal-to-noise ratio, and strong interference. The complexity of the subsurface structure leads to strong scattering of the refl ection points; thus, the curved-line acquisition method has been used. However, the actual subsurface structural characteristics have been rarely considered. We propose a design method for irregular acquisition based on common refl ection points（CRP） to avoid difficult-to-shoot areas, while considering the structural characteristics and CRP positions and optimizing the surfacereceiving line position. We arrange the positions of the receiving points to ensure as little dispersion of subsurface CRP as possible to improve the signal-to-noise ratio of the seismic data. We verify the applicability of the method using actual data from a site in Sichuan Basin. The proposed method apparently solves the problem of seismic data acquisition and facilitates seismic exploration in structurally complex areas.

Research on Agricultural Ontology and Fusion Rules Based Knowledge Fusion Framework

Currently, knowledge-based sharing and service system has been a hot issue and knowledge fusion, especially for implicit knowledge discovery, becomes the core of knowledge processing and optimization in the system. In the research, a knowledge fusion framework based on agricultural ontology and fusion rules was pro- posed, including knowledge extraction, clearing and annotation modules based on a- gricultural ontology, fusion rule construction, choosing and evaluation modules based on agricultural ontology and knowledge fusion module for users＇ demands. Finally, the significance of the framework to system of agricultural knowledge services was proved with the help of a case.

刘浩元：不安于平凡的内心

每个成功的80后都有颗不安于平凡的内心，他们在寻寻觅觅中找寻生存的价值，在看似平凡的轨迹上寻找并踏出一条不规则的曲线，有巅峰有高潮亦有海阔天空般的壮丽。80后的刘浩元，正带领一群80后的中坚力量，在继续着制造业的青春与热血、激情与梦想。

A novel MAC mechanism to resolve 802.11 performance anomaly

In the 802.11b networks, the guarantee of an equal long-run channel access probability causes performance anomaly in a multi-rate wireless cell. Much interest has been involved in this issue and many effective mechanisms have been proposed. The usual MAC layer solutions include the initial contention window adaptation, the maximum transfer unit size adaptation and the packet bursting. In this paper, we propose a novel approach which introduces a new parameter called the transmission prob- ability pt to the legacy protocol. By adjusting pt according to the transmission rate, the proposed scheme can solve the performance anomaly problem cleanly. Throughput analysis and performance evaluation show that our scheme achieves significant im- provement in the aggregate throughput and the fairness.

Nonequilibrium Statistical Physics Subject to the Anomalous Langevin Equation in Liouville Space

Considering that thermodynarmic irreversibility and hydrodynamic equations can not be derived rigorously and unifiedly from the Liouville equations, the anomalous Langevin equation in the Liouville space is proposed as a fundamental equation of statistical physics. This equation reflects that the law of motion of particles obeying reversible, deterministic laws in dynamics becomes irreversible and stochastic in thermodynamics. From this the fundamental equations of nonequilibrium thermodynamics, the principle of entropy increase and the theorem of minimum entropy production have been derived. The hydrodynamic equations, such as the generalized Navier-Stokes equation and the mass drift-diffusion equation etc. have been derived rigorously from the kinetic kinetic equation which is reduced from the anomalous Langevin equation in Liouville space. All these are unified and self consistent. But it is difficult to prove that entropy production density σ can never be negative everywhere for all the isolated inhomogeneous systems far from equilibrium.

Introducing aggregate into grouting material and its influence on load transfer of the rock bolting system

A fully grouted bolt provides greater shear load capacity for transmitting the load from the rock to the bolt, and vice versa. When grout fills irregularities between the bolt and the rock, a keying effect is created to transfer the load to the bolt via shear resistance at the interface and within the grout. Previous research has revealed that the mechanical properties of the grout had a great impact on the load transfer capacity of the rock bolting system. This paper presents a method to enhance the rock bolting strength by introducing metal granules into the grouting material. Experimental results suggest that both the average peak load of pullout tests and the total energy absorption of the system will increase if some metal granules are mixed into the resin.

Application of high temperature heat pipe in hypersonic vehicles thermal protection

In order to develop further the application of high temperature heat pipe in hypersonic vehicles thermal protection, the principles and characteristics of high temperature heat pipe used in hypersonic vehicles thermal protection were introduced. The methods of numerical simulation, theory analysis and experiment research were utilized to analyze the frozen start-up and steady state characteristic of the heat pipe as well as the machining improvement for fabricating irregularly shaped heat pipe which is suitable for leading edge of hypersonic vehicles. The results indicate that the frozen start-up time of heat pipe is long （10 min） and there exists large temperature difference along the heat pipe （47 ℃/cm）, but the heat pipe can reduce the temperature in stagnation area of hypersonic vehicles from 1 926 to 982 ℃ and work normally during 1 000-1 200℃. How to improve the maximum heat transfer capability and reduce the time needed for start-up from frozen state of the heat pipe by optimizing thermostructure such as designing of a novel wick with high performance is the key point in hypersonic vehicles thermal protection of heat pipe.

Effect of non-uniform stress characteristics on stress measurement in specimen

There is a remarkable difference in stress distribution between a specimen and a plate removed from the specimen.The plate presents a uniform stress distribution whereas the specimen presents a non-uniform stress distribution.Firstly,the real stress distributions in plates with thickness of 30,40 and 50 mm and then in the specimens were obtained through simulation and X-ray surface stress measurement.Secondly,in order to study the impact of specimens shapes and processing ways on the results accuracy,two irregular shapes (parallelogram and trapezoid) and two processing ways (saw and electron discharge machining (EDM)) were compared and analyzed by simulation and experiment using layer removal method,then the specimen effects on measurement results were evaluated.The results show that:1) the non-uniform stress distribution characteristics of the specimen near the surface of the cut is significant,the range of non-uniform stress distribution is approximately one-thickness distance away from the cut,and it decreases gradually along the depth;2) In order to ensure the stability in the results,it is suitable to take the specimen plane size 2-3 times of its thickness;3) Conventional processing methods have little effect on experimental results and the average deviation is less than 5%.

Rough interfaces and ultrasonic imaging logging behind casing

Ultrasonic leaky Lamb waves are sensitive to defects and debonding in multilayer media. In this study, we use the finite-difference method to simulate the response of flexural waves in the presence of defects owing to casing corrosion and rough fluctuations at the cement-formation interface. The ultrasonic obliquely incidence could effectively stimulate the flexural waves. The defects owing to casing corrosion change the amplitude of the early- arrival flexural wave, which gradually decrease with increasing defect thickness on the exterior walls and is the lowest when the defect length and wavelength were comparable. The scattering at the defects decreases the energy of flexural waves in the casing that leaks directly to fluids. For rough cement-formation interface, the early-arrival flexural waves do not change, whereas the late-arrival flexural waves have reduced amplitude owing to the scattering at rough interface.

Preconditioned prestack plane-wave least squares reverse time migration with singular spectrum constraint

Least squares migration can eliminate the artifacts introduced by the direct imaging of irregular seismic data but is computationally costly and of slow convergence. In order to suppress the migration noise, we propose the preconditioned prestack plane-wave least squares reverse time migration （PLSRTM） method with singular spectrum constraint. Singular spectrum analysis （SSA） is used in the preconditioning of the take-off angle-domain common-image gathers （TADCIGs）. In addition, we adopt randomized singular value decomposition （RSVD） to calculate the singular values. RSVD reduces the computational cost of SSA by replacing the singular value decomposition （SVD） of one large matrix with the SVD of two small matrices. We incorporate a regularization term into the preconditioned PLSRTM method that penalizes misfits between the migration images from the plane waves with adjacent angles to reduce the migration noise because the stacking of the migration results cannot effectively suppress the migration noise when the migration velocity contains errors. The regularization imposes smoothness constraints on the TADCIGs that favor differential semblance optimization constraints. Numerical analysis of synthetic data using the Marmousi model suggests that the proposed method can efficiently suppress the artifacts introduced by plane-wave gathers or irregular seismic data and improve the imaging quality of PLSRTM. Furthermore, it produces better images with less noise and more continuous structures even for inaccurate migration velocities.

Preparation of titanium powders by calciothermic reduction of titanium dioxide

To develop an effective process for titanium powders production, a calciothermic reduction process of pigment titanium dioxide （w（TiO2）〉98%）, based on the preform reduction process （PRP）, was investigated by means of XRD, SEM and EDS. In this process, the mixture of TiO2 powder and CaC12 was pressed into pieces as feed preform and was reduced by calcium vapor. Titanium powders was recovered after leaching from the reduced preform with hydrochloric acid and deionized water. The results indicate when the mass ratio of CaC12 to TiO2 is about 1：4 and at a constant temperature of 1 273 K for 6 h in vacuum furnace, titanium powders with 99.55% purity by EDS analysis and irregular shape （8-15 μm in particle size） are obtained.

FRACTAL KINEMATICS OF CRACK PROPAGATION IN GEOMATERIALS

Experimental results indicate that propagation paths of cracks in geomaterials are often irregular. producing rough fracture surfaces which are fractal. A formula is derived for the fractal kinematics of crack propagation in geomaterials. The formula correlates the dynamic and static fracture toughnesses with crack velocity, crack length and a microstructural parameter, and allows the fractal dimension to be obtained. From the equations for estimating crack velocity and fractal dimension it can be shown that the measured crack ve1ocity, Vo, should be much smaller than the fractal crack velocity, V. It can also be shown that the fractal dimension of the crack propagation path can be calculated directly from Vo and from the fracture toughness.

RESEARCH ON FRACTAL CHARACTERISTICS OF URBAN TRAFFIC NETWORK STRUCTURE BASED ON GIS

Traffic network is an importance asp ect of researching controllable parameters of an urban spatial morpholo-gy.Based on GIS,traffic network str ucture complexity can be understood by using fractal geometry in which th e length-radius dimension describes change of network density,and ramification-radius dimension describes complexity and accessibility of urban network.It i s propitious to analyze urban traffic network and to understand dynamic c hange process of traffic network using expanding f ractal-dimension quantification.Meanwhile the length-radius dimension and ramifica-tion-radius dimension could be rega rd as reference factor of quantitative describing urban traffic network.

Microstructures and thermal properties of municipal solid waste incineration fly ash

To analyze the feasibility of utilization of thermal technology in fly ash treatment, thermal properties and microstructures of municipal solid waste incineration （MSW1） fly ash were studied by measuring the chemical element composition, specific surface area, pore sizes, functional groups, TEM image, mineralogy and DSC-TG curves of raw and sintered fly ash specimens. The results show that MSWI fly ash particles mostly have irregular shapes and non-typical pore structure, and the supersonic treatment improves the pore structure; MSWI fly ash consists of Such crystals as SiO2, CaSO4 and silica-aluminates, and some soluble salts like KCl and NaCl. During the sintering process, mineralogy changes largely and novel solid solutions are produced gradually with the rise of temperature. Therefore, the utilization of a proper thermal technology not only destructs those persistent organic toxicants but also stabilizes hazardous heavy metals in MSWI fly ash.