The effect of intermetallic compounds on the heat resistance of transition joint was investigated. The experiment of post-weld heat treatment for the hot roll bonded titanium alloy-stainless steel joint using nickels ...The effect of intermetallic compounds on the heat resistance of transition joint was investigated. The experiment of post-weld heat treatment for the hot roll bonded titanium alloy-stainless steel joint using nickels interlayer was carried out, and the interface microstructure evolution due to heat treatment was presented. There was not found significant interdiffusion at stainless steel/nickel interface, when the specimens were heat treated in the temperature range of 600-800 °C for 10 and 30 min, while micro-cracks occurred at the stainless steel/nickel interface heat treated at 700 °C for 30 min. The thickness of intermetallic layers at nickel/titanium alloy interface increased at 600 °C, and micro-cracks occurred at 700 and 800 °C. The micro-cracks occurred between intermetallic layers or between intermetallic layer and nickel interlayer as well. The tensile strength of the transition joint decreased with the increase of heat treatment temperature or holding time.展开更多
To investigate the effect of aging treatment on irradiation-induced segregation of high Mn-Cr steel, specimens for electron-beam irradiation were prepared from the high Mn-Cr austenitic steel which was solution treate...To investigate the effect of aging treatment on irradiation-induced segregation of high Mn-Cr steel, specimens for electron-beam irradiation were prepared from the high Mn-Cr austenitic steel which was solution treated at 1 373 K for 1 h and aging treated at 573 K for 1 000 h, respectively. The electron-beam irradiation was performed at 573 K up to doses of 5.4 dpa in a 1 250 kV HVEM and irradiation-induced segregation analyses were carried out by an EDX in a 200 kV FE-TEM. The results show that void formation is not observed in both solution treated and aging treated ones. The amount of Cr segregation at the grain boundary decreases in the aged one; however, that of Mn is not changed in solution treated one.展开更多
In the present study,the effects of microstructure,grain size,and texture after thermomechanical processing on the corrosion behavior of AISI 321 austenitic stainless steel(ASS)were studied.The as-received,coarse-grai...In the present study,the effects of microstructure,grain size,and texture after thermomechanical processing on the corrosion behavior of AISI 321 austenitic stainless steel(ASS)were studied.The as-received,coarse-grained steel((35±3)μm)was subjected to 20%,50%and 90%thickness reduction through cold rolling at liquid nitrogen temperature,followed by annealing at 750,950 and 1050℃for 15 min.Recrystallization occurred after annealing at 750℃,and with the increasing of annealing temperature to 950℃and 1050℃,secondary recrystallization(abnormal grain growth)and grain growth were observed.The results showed that,after 20%thickness reduction,corrosion resistance increased significantly(21.1 kΩ·cm^(2))compared with the as-received condition(3.9 kΩ·cm^(2))due to the enhancement ofγ-fiber and the creation ofΣ3 boundaries.In contrast,the corrosion resistance decreased with the increasing of thickness reduction to 90%during rolling,but still depicted higher corrosion resistance compared with the as-received specimen.After annealing the 90%cold rolled(CR)specimens at 750 and 950℃,the corrosion resistance increased in comparison with the as-received sample as a result of the more uniform microstructure,appearance of Goss and brass texture components,and grain refinement.However,significant grain growth((112±76)μm)followed by a non-uniform structure was observed after annealing at 1050℃and resulted in the lowest corrosion resistance(1.3 kΩ·cm^(2)).展开更多
Austenitic stainless steels, when exposed to welding conditions or aging for length of service, it＇s observed the formation of numerous deleterious phases, such as several kinds of carbides type MC, M6C, M7C3, M23C6,...Austenitic stainless steels, when exposed to welding conditions or aging for length of service, it＇s observed the formation of numerous deleterious phases, such as several kinds of carbides type MC, M6C, M7C3, M23C6, and intermetallic secondary phases （sigma, chi, laves）, which cause the process of intergranular corrosion. The aim of this work was verifying the formation of the types of carbides and/or intermetallic phases existing in the stainless AISI 304 at 800 ℃, varying the timing of heat treatment between 30, 360 and 1,440 min. The optical microscopy analysis revealed the predominant formation of the carbide type M23C6. The results of DL-EPR （double loop electrochemical potentiokinetic reactivation） tests showed a gradual increase in the precipitation of this carbide with the increase of treatment time. The potentiodynamic polarization showed that the precipitation of this carbide reduce the formation of the Cr2O3 passive layer, suggesting that the precipitate carbide to be predominantly of the Cr23C6 type.展开更多
Micro plasma arc surface melting of 0Cr19Ni9 shielded metal arc welding joint with a micro plasma arc welder produced a thin surface melted layer with a refined microstructure. The surface treatment changed the anod...Micro plasma arc surface melting of 0Cr19Ni9 shielded metal arc welding joint with a micro plasma arc welder produced a thin surface melted layer with a refined microstructure. The surface treatment changed the anodic polarization behavior in 0.5 mol/L H 2SO 4 solution. The polarization tests showed that for the as welded joint both the heat affected zone and the weld metal decreased in resistance to corrosion compared with the as received parent material while for the micro plasma arc surface melted joint the corrosion resistance increased significantly. This increase in corrosion resistance is attributed to the rapid solidification of the melted layer. Rapid solidification of the melted layer refines its microstructure, decreases its microsegregation, and inhibits the precipitation of chromium carbides at the grain boundaries.展开更多
基金Project(AWPT-M07)supported by the State Key Laboratory of Advanced Welding and Joining,Harbin Institute of Technology
文摘The effect of intermetallic compounds on the heat resistance of transition joint was investigated. The experiment of post-weld heat treatment for the hot roll bonded titanium alloy-stainless steel joint using nickels interlayer was carried out, and the interface microstructure evolution due to heat treatment was presented. There was not found significant interdiffusion at stainless steel/nickel interface, when the specimens were heat treated in the temperature range of 600-800 °C for 10 and 30 min, while micro-cracks occurred at the stainless steel/nickel interface heat treated at 700 °C for 30 min. The thickness of intermetallic layers at nickel/titanium alloy interface increased at 600 °C, and micro-cracks occurred at 700 and 800 °C. The micro-cracks occurred between intermetallic layers or between intermetallic layer and nickel interlayer as well. The tensile strength of the transition joint decreased with the increase of heat treatment temperature or holding time.
文摘To investigate the effect of aging treatment on irradiation-induced segregation of high Mn-Cr steel, specimens for electron-beam irradiation were prepared from the high Mn-Cr austenitic steel which was solution treated at 1 373 K for 1 h and aging treated at 573 K for 1 000 h, respectively. The electron-beam irradiation was performed at 573 K up to doses of 5.4 dpa in a 1 250 kV HVEM and irradiation-induced segregation analyses were carried out by an EDX in a 200 kV FE-TEM. The results show that void formation is not observed in both solution treated and aging treated ones. The amount of Cr segregation at the grain boundary decreases in the aged one; however, that of Mn is not changed in solution treated one.
基金Project(scu.EM1400.30796)supported by the Shahid Chamran University of Ahvaz,Iran。
文摘In the present study,the effects of microstructure,grain size,and texture after thermomechanical processing on the corrosion behavior of AISI 321 austenitic stainless steel(ASS)were studied.The as-received,coarse-grained steel((35±3)μm)was subjected to 20%,50%and 90%thickness reduction through cold rolling at liquid nitrogen temperature,followed by annealing at 750,950 and 1050℃for 15 min.Recrystallization occurred after annealing at 750℃,and with the increasing of annealing temperature to 950℃and 1050℃,secondary recrystallization(abnormal grain growth)and grain growth were observed.The results showed that,after 20%thickness reduction,corrosion resistance increased significantly(21.1 kΩ·cm^(2))compared with the as-received condition(3.9 kΩ·cm^(2))due to the enhancement ofγ-fiber and the creation ofΣ3 boundaries.In contrast,the corrosion resistance decreased with the increasing of thickness reduction to 90%during rolling,but still depicted higher corrosion resistance compared with the as-received specimen.After annealing the 90%cold rolled(CR)specimens at 750 and 950℃,the corrosion resistance increased in comparison with the as-received sample as a result of the more uniform microstructure,appearance of Goss and brass texture components,and grain refinement.However,significant grain growth((112±76)μm)followed by a non-uniform structure was observed after annealing at 1050℃and resulted in the lowest corrosion resistance(1.3 kΩ·cm^(2)).
文摘Austenitic stainless steels, when exposed to welding conditions or aging for length of service, it＇s observed the formation of numerous deleterious phases, such as several kinds of carbides type MC, M6C, M7C3, M23C6, and intermetallic secondary phases （sigma, chi, laves）, which cause the process of intergranular corrosion. The aim of this work was verifying the formation of the types of carbides and/or intermetallic phases existing in the stainless AISI 304 at 800 ℃, varying the timing of heat treatment between 30, 360 and 1,440 min. The optical microscopy analysis revealed the predominant formation of the carbide type M23C6. The results of DL-EPR （double loop electrochemical potentiokinetic reactivation） tests showed a gradual increase in the precipitation of this carbide with the increase of treatment time. The potentiodynamic polarization showed that the precipitation of this carbide reduce the formation of the Cr2O3 passive layer, suggesting that the precipitate carbide to be predominantly of the Cr23C6 type.
文摘Micro plasma arc surface melting of 0Cr19Ni9 shielded metal arc welding joint with a micro plasma arc welder produced a thin surface melted layer with a refined microstructure. The surface treatment changed the anodic polarization behavior in 0.5 mol/L H 2SO 4 solution. The polarization tests showed that for the as welded joint both the heat affected zone and the weld metal decreased in resistance to corrosion compared with the as received parent material while for the micro plasma arc surface melted joint the corrosion resistance increased significantly. This increase in corrosion resistance is attributed to the rapid solidification of the melted layer. Rapid solidification of the melted layer refines its microstructure, decreases its microsegregation, and inhibits the precipitation of chromium carbides at the grain boundaries.
