二氢化碳水防止蛋壳破碎

鸡蛋容易破碎(尤其是夏天),这是因为鸡体内呼出大量二氧化碳,血中酸碱度增高。

Advances in the studies of the supported ruthenium catalysts for CO_(2)methanation

CO_(2)methanation has a potential in the large-scale utilization of carbon dioxide.It has also been considered to be useful for the renewable energy storage.The commercial pipeline for natural gas transportation can be directly applied for the methane product of CO_(2)methanation.The supported ruthenium(Ru)catalyst has been confirmed to be active and stable for CO_(2)methanation with its high ability in the dissociation of hydrogen and the strong binding of carbon monoxide.CO_(2)methanation over the supported Ru catalyst is structure sensitive.The size of the Ru catalyst and the support have significant effects on the activity and the mechanism.A significant challenge re-mained is the structural controllable preparation of the supported Ru catalyst toward a sufficiently high low-temperature activity.In this review,the recent progresses in the investigations of the supported Ru catalysts for CO_(2)methanation are summarized.The challenges and the future devel-opments are also discussed.

大气CO_2增加对生态系统的影响

根据Ｃ＿３植物和Ｃ＿４植物对高浓度ＣＯ＿２的不同反应，评述了富ＣＯ＿２大气对生态系统的影响。结论是大气ＣＯ＿２浓度增加将导致生态系统发生一系列变化，包括生物多样世的减少、营养循环受阻、虫灾发生和温室效应加剧等。

Octahedral Cu_2O-modified TiO_2 nanotube arrays for efficient photocatalytic reduction of CO_2

A photocatalyst composed of TiO 2 nanotube arrays（TNTs） and octahedral Cu2 O nanoparticles was fabricated,and its performance in the photocatalytic reduction of CO2 under visible and simulated solar irradiation was studied. The average nanotube diameter and length was 100 nm and 5 μm,respectively. The different amount of octahedral Cu2 O modified TNTs were obtained by varying electrochemical deposition time. TNTs modified with an optimized amount of Cu2 O nanoparticles exhibited high efficiency in the photocatalysis,and the predominant hydrocarbon product was methane. The methane yield increased with increasing Cu2 O content of the catalyst up to a certain deposition time,and decreased with further increase in Cu2 O deposition time. Insufficient deposition time（5 min） resulted in a small amount of Cu2 O nanoparticles on the TNTs,leading to the disadvantage of harvesting light. However,excess deposition time（45 min） gave rise to entire TNT surface being most covered with Cu2 O nanoparticles with large sizes,inconvenient for the transport of photo-generated carriers. The highest methane yield under simulated solar and visible light irradiation was observed for the catalysts prepared at a Cu2 O deposition time of 15 and 30 min respectively. The morphology,crystallization,photoresponse and electrochemical properties of the catalyst were characterized to understand the mechanism of its high photocatalytic activity. The TNT structure provided abundant active sites for the adsorption of reactants,and promoted the transport of photogenerated carriers that improved charge separation. Modifying the TNTs with octahedral Cu2 O nanoparticles promoted light absorption,and prevented the hydrocarbon product from oxidation. These factors provided the Cu2O-modified TNT photocatalyst with high efficiency in the reduction of CO2,without requiring co-catalysts or sacrificial agents.

Killing Effect of Mixed Fumigation of Phosphine and Carbon Dioxide on Eggs of Lasioderma serricorne F.

[Objective] This study aimed to investigate the killing effect of mixed fumi- gation of phosphine and carbon dioxide on eggs of Lasioderma serricorne F. [Method] The outside-storage phosphine generator was placed in a tabernacled smoke box, and the mortality rates of L. serricome F. eggs in the smoke box under conditions of different aluminium phosphide usage amount and different fumigation time were studied. In addition, the times needed by tabernacle and smoke box cen- ter to reach the phosphine concentration peak were recorded. [Result] The optimum conditions for killing the eggs of L. serricorne were as follows： temperature of （27± 2） ℃, relatively humidity of （45±5）%, aluminium phosphide usage amount of 1.5 g/m3 and effective exposure time of 96 h. The killing effect of mixed fumigation of phos- phine and carbon dioxide was increased with the extension of fumigation time. The increased usage amount of aluminium phosphide showed no significant effect on killing effect. The tabernacle space and smoke box center all required relatively short time to reach the phosphine concentration peak. If the tabernacle had a good airtightness, the overall fumigation time could be shortened. [Conclusion] The fumi- gation method is reliable, and it can be used for the control of L. serricorne F. in tobacco storage.

MXenes as noble-metal-alternative co-catalysts in photocatalysis

Photocatalysis has become a focal point in research as a clean and sustainable technology with the potential to solve environmental problems and energy crises.The loading of noble-metal co-catalysts can substantially improve the photocatalytic efficiency of semiconductors.Because the high cost and scarcity of noble metals markedly limit their large-scale applications,finding a noble-metal-alternative co-catalyst is crucial.MXene,a novel 2D transition metal material,has attracted considerable attention as a promising substitute for noble metal co-catalysts owing to its cost-efficiency,unique 2D layered structure,and excellent electrical,optical,and thermodynamic properties.This review focuses on the latest advancements in research on MXenes as co-catalysts in relatively popular photocatalytic applications(hydrogen production,CO2 reduction,nitrogen fixation,and organic pollutant oxidation).The synthesis methods and photocatalytic mechanisms of MXenes as co-catalysts are also summarized according to the type of MXene-based material.Finally,the crucial opportunities and challenges in the prospective development of MXene-based photocatalysts are outlined.We emphasize that modern techniques should be used to demonstrate the effects of MXenes on photocatalysis and that the photocatalytic activity of MXene-based photocatalysts can be further improved using defective engineering and recent phenomena such as the localized surface plasmon resonance effect and single-atom catalysis.

Layered double hydroxide photocatalysts for solar fuel production

Splitting water or reducing CO_(2) via semiconductor photocatalysis to produce H2 or hydrocarbon fuels through the direct utilization of solar energy is a promising approach to mitigating the current fossil fuel energy crisis and environmental challenges.It enables not only the realization of clean,renewable,and high-heating-value solar fuels,but also the reduction of CO_(2) emissions.Layered double hydroxides(LDHs)are a type of two-dimensional anionic clay with a brucite-like structure,and are characterized by a unique,delaminable,multidimensional,layered structure;tunable intralayer metal cations;and exchangeable interlayer guest anions.Therefore,it has been widely investigated in the fields of CO_(2) reduction,photoelectrocatalytic water oxidation,and water photolysis to produce H2.However,the low carrier mobility and poor quantum efficiency of pure LDH limit its application.An increasing number of scholars are exploring methods to obtain LDH-based photocatalysts with high energy conversion efficiency,such as assembling photoactive components into LDH laminates,designing multidimensional structures,or coupling different types of semiconductors to construct heterojunctions.This review first summarizes the main characteristics of LDH,i.e.,metal-cation tunability,intercalated guest-anion substitutability,thermal decomposability,memory effect,multidimensionality,and delaminability.Second,LDHs,LDH-based composites(metal sulfide-LDH composites,metal oxide-LDH composites,graphite phase carbon nitride-LDH composites),ternary LDH-based composites,and mixed-metal oxides for splitting water to produce H_(2) are reviewed.Third,graphite phase carbon nitride-LDH composites,MgAl-LDH composites,CuZn-LDH composites,and other semiconductor-LDH composites for CO_(2) reduction are introduced.Although the field of LDH-based photocatalysts has advanced considerably,the photocatalytic mechanism of LDHs has not been thoroughly elucidated;moreover,the photocatalytic active sites,the synergy between different components,and the interfacial reaction mechanism of LDH-based photocatalysts require further investigation.Therefore,LDH composite materials for photocatalysis could be developed through structural regulation and function-oriented design to investigate the effects of different components and interface reactions,the influence of photogenerated carriers,and the impact of material composition on the physical and chemical properties of the LDH-based photocatalyst.

Highly dispersed Cd cluster supported on TiO_(2) as an efficient catalyst for CO_(2) hydrogenation to methanol

The conversion of CO_(2) to methanol with high activity and high selectivity remains challenging owing to the kinetic and thermodynamic limitations associated with the low chemical reactivity exhibited by CO_(2).Herein,we report a novel Cd/TiO_(2) catalyst exhibiting a methanol selectivity of 81%,a CO_(2) conversion of 15.8%,and a CH_(4) selectivity below 0.7%.A combination of experimental and computational studies revealed that the unique electronic properties exhibited by the Cd clusters supported by the TiO_(2) matrix were responsible for the high selectivity of CO_(2) hydrogenation to methanol via the HCOO*pathway at the interfacial catalytic sites.

Copper-ceria solid solution with improved catalytic activity for hydrogenation of CO to CHOH

A copper-ceria solid solution and ceria-supported copper catalysts were prepared and used for the catalytic hydrogenation of CO2 to CH3OH.According to site-specific classification and quantitative analyses(X-ray diffraction,Raman spectroscopy,X-ray photoelectron spectroscopy,H2 temperature-programmed reduction,and CO adsorption),the interfaces of the prepared catalysts were classified as Cu incorporated into ceria(Cu-Ov-Cex),dispersed Cu O(D-Cu O-Ce O2),and bulk Cu O(B-Cu O-Ce O2)over the Ce O2 surface.These results,together with those of activity tests,showed that the Cu-Ov-Cex species was closely related to the CO2 hydrogenation activity and resulted in a much higher turnover frequency of CH3OH production than that observed with the D-Cu O-Ce O2 and B-Cu O-Ce O2 species.Thus,the copper-ceria solid solution exhibited improved activity due to the higher Cu-Ov-Cex fraction.

CO_2 hydrogenation to methanol over Cu/Zn/Al/Zr catalysts prepared by liquid reduction

Cu/Zn/Al/Zr catalysts containing Cu in three valence states(Cu2+,Cu+and Cu0)were prepared usinga liquid reduction method and subsequently calcined at different temperatures.The effects of thecalcination temperature on the catalyst structure,interactions among components,reducibility anddispersion of Cu species,surface properties and exposed Cu surface area were systematically investigated.These materials were also applied to the synthesis of methanol via the hydrogenation ofCO2.The results show that a large exposed Cu surface area promotes catalytic CO2conversion andthat there is a close correlation between the Cu+/Cu0ratio and the selectivity for methanol.A calcinationtemperature of573K was found to produce a Cu/Zn/Al/Zr catalyst exhibiting the maximumactivity during the synthesis of methanol.

Effect of In_(2)O_(3)particle size on CO_(2) hydrogenation to lower olefins over bifunctional catalysts

A reaction-coupling strategy is often employed for CO_(2)hydrogenation to produce fuels and chemicals using oxide/zeolite bifunctional catalysts.Because the oxide components are responsible for CO_(2)activation,understanding the structural effects of these oxides is crucial,however,these effects still remain unclear.In this study,we combined In_(2)O_(3),with varying particle sizes,and SAPO‐34 as bifunctional catalysts for CO_(2)hydrogenation.The CO_(2)conversion and selectivity of the lower olefins increased as the average In_(2)O_(3)crystallite size decreased from 29 to 19 nm;this trend mainly due to the increasing number of oxygen vacancies responsible for CO_(2) and H_(2) activation.However,In_(2)O_(3)particles smaller than 19 nm are more prone to sintering than those with other sizes.The results suggest that 19 nm is the optimal size of In_(2)O_(3)for CO_(2)hydrogenation to lower olefins and that the oxide particle size is crucial for designing catalysts with high activity,high selectivity,and high stability.

Effect of alkali metals on the performance of CoCu/TiO_2 catalysts for CO_2 hydrogenation to long-chain hydrocarbons

CoCu/TiO_2 catalysts promoted using alkali metals（Li, Na, K, Rb, and Cs） were prepared by the homogeneous deposition-precipitation method followed by the incipient wetness impregnation method. The influences of the alkali metals on the physicochemical properties of the CoCu/TiO_2 catalysts and the catalytic performance for CO_2 hydrogenation to long-chain hydrocarbons（C_（5＋））were investigated in this work. According to the characterization of the catalysts based on X-ray photoelectron spectroscopy, X-ray diffraction, CO_2 temperature-programmed desorption（TPD）, and H_2-TPD, the introduction of alkali metals could increase the CO_2 adsorption and decrease the H_2 chemisorption, which could suppress the formation of CH_4, enhance the production of C_（5＋）, and decrease the hydrogenation activity. Among all the promoters, the Na-modified CoCu/TiO_2 catalyst provided the maximum C_（5＋） yield of 5.4%, with a CO_2 conversion of 18.4% and C_（5＋） selectivity of42.1%, because it showed the strongest basicity and a slight decrease in the amount of H_2 desorption;it also exhibited excellent catalytic stability of more than 200 h.

Direct carbon dioxide hydrogenation to produce bulk chemicals and liquid fuels via heterogeneous catalysis

The hydrogenation of carbon dioxide(CO_(2))to produce chemicals and transportation liquid fuels in huge demand via heterogeneous thermochemical catalysis achieved using renewable energy has received increasing attention,and substantial advances have been made in this research field in recent years.In this study,we summarize our progress in the rational design and construction of highly efficient catalysts for CO_(2) hydrogenation to methanol,lower olefins,aromatics,and gasolineand jet fuel-range hydrocarbons.The structure‐performance relationship,nature of the active sites,and mechanism of the reactions occurring over these catalysts are explored by combining computational and experimental evidence.The results of this study will promote further fundamental studies and industrial applications of heterogeneous catalysts for CO_(2) hydrogenation to produce bulk chemicals and liquid fuels.

Electrolytic Regeneration of Decarbonising Potassium Carbonate Solution

In this work,the regeneration mechanism of potassium carbonate solution after absorption of CO2 using ion-exchange membrane electrolysis was presented.The solutions of potassium carbonate(K2CO3) and potassium bicarbonate(KHCO3) were used to simulate the solution after absorbing CO2.Experiments were carried out at various electrodes,temperatures and current densities.The results indicate that the membrane electrolysis can in-crease concentration ratio of K2CO3 and KHCO3,and achieve 100%conversion.In this process,not only CO2 is desorbed from carbonate solution,but also hydrogen,as a byproduct,is generated at the cathode,which is the main contributor to reduce energy consumption.Thus,the membrane electrolysis is valuable in the regeneration of the K2CO3 absorbent.

The Characteristics of a Sorption-enhanced Steam-Methane Reaction for the Production of Hydrogen Using CO_2 Sorbent

The objective of the present study is to characterize the production of hydrogen with a sorptionenhanced steam-methane reaction process using Ca(OH)2 as the CO2 adsorbent. Theoretical equilibrium compositions at different operation conditions were calculated using an iterative method. It was found that with Ca(OH)2 as the CO2 sorbent, the concentration of CO2 adsorption was reduced in the product stream, that gave rise to higher methane conversion and higher H2 concentration. An experimental setup was built to test the theoretical calculation. The effects of sorbents and the particle size of Ca(OH)2 on the concentration of CO2 and H2 were investigated in detail. Results showed that the reactor packed with catalyst and Ca(OH)2 particles produced H2 concentration of 94%. It was nearly 96% of the theoretical equilibrium limit, much higher than H2 equilibrium concentration of 67.5% without CO2 sorption under the same conditions of 500℃, 0.2 MPa pressure and a steam-to-methane ratio 6. In addition, the residual mole fraction of CO2 was less than 0.001.

Visible light-enhanced photothermal CO2 hydrogenation over Pt/Al2O3 catalyst

Light illumination has been widely used to promote activity and selectivity of traditional thermal catalysts. Nevertheless, the role of light irradiation during catalytic reactions is not well understood. In this work, Pt/Al2 O3 prepared by wet impregnation was used for photothermal CO2 hydrogenation, and it showed a photothermal effect. Hence, operando diffuse reflectance infrared Fourier-transform spectroscopy and density functional theory calculations were conducted on Pt/Al2 O3 to gain insights into the reaction mechanism. The results indicated that CO desorption from Pt sites including step sites(Ptstep) or/and terrace site(Ptterrace) is an important step during CO2 hydrogenation to free the active Pt sites. Notably, visible light illumination and temperature affected the CO desorption in different ways. The calculated adsorption energy of CO on Ptstep and Ptterrace sites was-1.24 and-1.43 e V, respectively. Hence, CO is more strongly bound to the Ptstep sites. During heating in the dark, CO preferentially desorbs from the Ptterrace site. However, the additional light irradiation facilitates transfer of CO from the Ptstep to Ptterrace sites and its subsequent desorption from the Ptterrace sites, thus promoting the CO2 hydrogenation.

Catalytic synthesis of diethyl carbonate with supported Pd-Cu bimetallic nanoparticle catalysts:Cu(Ⅰ) as the active species

Cupric oxide （CuO） and copper-cuprous oxide （Cu-Cu2O） nanoparticles were prepared by a simple hydrothermal method for the synthesis of diethyi carbonate （DEC） from ethanol. During these syntheses, varying NaOH and glucose concentrations were applied to explore and pinpoint the active species. It was found that PdCl2/CuO and PdCI2/Cu-Cu2O both catalysts exhibited good thermal stability and morphology. The results of catalytic tests showed that the catalysts prepared with 5 mol/L NaOH show superior catalytic performances because of their lower extent of agglomeration. It is noteworthy that the PdC12/Cu-Cu2O catalysts were the most active, especially the PdCl2/Cu-Cu2O catalyst prepared with 10 mmol glucose and having a higher Cu2O concentration. In Pd（ll）-Cu（II） （PdCl2/CuO） catalysts, there is an induction period, during which Pd（II） is reduced to Pd（0）, that must occur prior to electron transfer between Pd and Cu, and this can slow the catalytic reaction. To further pinpoint the active species, PdCl2/Cu-Cu2O catalysts with different Cu2O contents were prepared by controlling the dosages of glucose. The maximum DEC yield obtained with these catalysts was 151.9 mg.g-1.h-1, corresponding to an ethanol conversion of 7.2% and 97.9% DEC selectivity on an ethanol basis. Therefore, it was concluded that Cu＋ was the active species in this catalytic system, possibly because a higher proportion of Cu＋ reduces the Pd2＋ concentration and limits the CO oxidation side reaction, thus increasing DEC selectivity. In addition, Cu＋ promotes electron transfer between Pd and Cu without an induction period, which could also promote the catalytic activity.

Strategies to improve electrocatalytic and photocatalytic performance of two-dimensional materials for hydrogen evolution reaction

Two-dimensional materials(2D)with unique physicochemical properties have been widely studied for their use in many applications,including as hydrogen evolution catalysts to improve the efficiency of water splitting.Recently,typical 2D materials MoS2,graphene,MXenes,and black phosphorus have been widely investigated for their application in the hydrogen evolution reaction(HER).In this review,we summarize three efficient strategies—defect engineering,heterostructure formation,and heteroatom doping—for improving the HER performance of 2D catalysts.The d-band theory,density of states,and Fermi energy level are discussed to provide guidance for the design and construction of novel 2D materials.The challenges and prospects of 2D materials in the HER are also considered.

Efficient hydrocarboxylation of alkynes based on carbodiimide‐regulated in situ CO generation from HCOOH:An alternative indirect utilization of CO_(2)

The role of carbodiimide as dehydrant in the chemo‐,regio‐and stereoselective Pd(Ⅱ/0)‐catalyzed hydrocarboxylation of various alkynes with HCOOH releasing CO in situ is reported for the first time to obtainα,β‐unsaturated carboxylic acids.Both symmetrical and unsymmetrical monoalkynes show good reactivity.Importantly,2,2’‐(1,4‐phenylene)diacrylic acid can also be synthesized in high yield through the dihydrocarboxylation of 1,4‐diethynylbenzene.Besides,an excellent result in gram scale experiment and TON up to 900 can be obtained,displaying the efficiency of this protocol.Notably,regulating the types and concentrations of dehydrant can control the CO generation,avoiding directly operating toxic CO and circumventing sensitivity issue to the CO amount.On the basis of the attractive features of formic acid including easy preparation through CO_(2) hydrogenation and efficient liberation of CO,this protocol using formic acid as bridging reagent between CO_(2) and CO can be perceived as an indirect utilization of CO_(2),offering an alternative method for preparing acrylic acid analogues.