A facile and efficient diastereoselective synthesis of methyl 3β-hydroxyeudesmane-4,11(13)-dien-12-oicate starting from (+)-dihydrocarvone has been carried out in 9 steps at the first time.
High-pressure vapor-liquid equilibrium data for the binary systems of methyl propionate＋carbon dioxide and propyl propionate＋carbon dioxide were measured at pressure from 1.00 MPa to 12.00 MPa and temperature in the...High-pressure vapor-liquid equilibrium data for the binary systems of methyl propionate＋carbon dioxide and propyl propionate＋carbon dioxide were measured at pressure from 1.00 MPa to 12.00 MPa and temperature in the range from 313 K to 373 K. Experimental results were correlated with the Peng-Robinson equation of state with the two-parameter van der Waals mixing rule. At the same time, the Henry＇s coefficient, partial molar enthalpy change and partial molar entropy change of CO2 during dissolution at different temperature were also calculated.展开更多
为研究长叶香茶菜Rabdosia stracheyi(Benth ex Hook.)Hara的化学成分,本文采用硅胶、反相硅胶C 18、葡聚糖凝胶Sephadex LH-20、反相半制备高效液相等色谱方法对长叶香茶菜地上部分进行分离、纯化,利用1 H NMR、13 C NMR、HR-ESI-MS等...为研究长叶香茶菜Rabdosia stracheyi(Benth ex Hook.)Hara的化学成分,本文采用硅胶、反相硅胶C 18、葡聚糖凝胶Sephadex LH-20、反相半制备高效液相等色谱方法对长叶香茶菜地上部分进行分离、纯化,利用1 H NMR、13 C NMR、HR-ESI-MS等波谱数据,结合参考文献,鉴定化合物的结构。结果表明,从长叶香茶菜地上部分分离得到12个三萜类化合物,它们分别是木栓醇(1)、齐墩果酸(2)、3β-羟基-齐墩果烷-11,13(18)-二烯-28酸(3)、2α,3α-二羟基齐墩果-12-烯-28酸(4)、2 a,3a,24-三羟基-12-烯-28-齐墩果酸(5)、2α,3β,24-三羟基齐墩果-12-烯-28酸(6)、cleistocalyxin(7)、熊果醇(8)、2α-羟基乌苏酸(9)、2a,3a,24-三羟基熊果-12,20(30)-二烯-28-酸甲酯(10)、maquatic acid(11)和2α,3α,24-三羟基-12,20(30)-二烯乌苏酸(12)。以上得到的三萜类化合物均为首次从该植物中分离得到。展开更多
Acrylonitrile-methyl methacrylate （AN-MMA） copolymer/silica nanocomposites were synthesized by in-situ emulsion polymerization initiated by 2,2＇-azobis（2-amidinopropane） dihydrochloride absorbed onto colloidal si...Acrylonitrile-methyl methacrylate （AN-MMA） copolymer/silica nanocomposites were synthesized by in-situ emulsion polymerization initiated by 2,2＇-azobis（2-amidinopropane） dihydrochloride absorbed onto colloidal silica particles, and the mesoporous carbon materials were prepared through carbonization of the obtained AN-MMA copolymer/silica nanocomposites, followed by HF etching. Thermogravimetric analysis of AN-MMAcopolymer/silica nanocomposltes snoweO mat me caroon ylelCl or copolymer was slgnuy oecreaseo as Silica parucle incorporated. N2 adsorption-desorption, scan electron microscopy （SEM） and transmission electron microscopy （TEM） were used to characterize the structure and morphology of the mesoporous carbon materials. Both SEM and展开更多
A kinetic model was developed to describe the atom transfer radical polymerization (ATRP) of 2(N,N-dimethylarnino) ethyl methacrylate (DMAEMA). The model was based on a polymerization mechanism, which included the ato...A kinetic model was developed to describe the atom transfer radical polymerization (ATRP) of 2(N,N-dimethylarnino) ethyl methacrylate (DMAEMA). The model was based on a polymerization mechanism, which included the atom transfer equilibrium for primary radical, the propagation of growing polymer radical, and the atom transfer equilibrium for the growing polymer radical. An experiment was carried out to measure the conversion of monomer, the number-average molecular weight of polymer and molecular weight distribution for the ATRP process of DMAEMA. The experimental data were used to correlate the kinetic model and rate constants were obtained. The rate constants of activation and deactivation in the atom transfer equilibrium for primary radical are 1.0 x 10(4) L(.)mol(-1.)s(-1) and 0.04 L(.)mol(-1.)s(-1), respectively. The rate constant of the propagation of growing polymer radical is 8.50 L(.)mol(-1.)s(-1), and the rate constants of activation and deactivation in the atom transfer equilibrium for growing polymer radical are 0.045 L(.)mol(-1.)s(-1) and 1.2 x 10(5) L(.)mol(-1.)s(-1), respectively. The values of the rate constants represent the features of the ATRP process. The kinetic model was used to calculate the ATRP process of DMAEMA. The results show that the calculations agree well with the measurements.展开更多
We proposed a novel method of fabricating polydimethylsiloxane (PDMS) microfluidic chip polymer master molds in this paper. The method mainly includes two steps. First, a stainless steel slice was laser etched to form...We proposed a novel method of fabricating polydimethylsiloxane (PDMS) microfluidic chip polymer master molds in this paper. The method mainly includes two steps. First, a stainless steel slice was laser etched to form a metal model. Then, the organic solution of poly(methyl methacrylate) (PMMA) was casted onto the metal model to fabricate the PMMA master which subsequently would be used to fabricate PDMS chips. We systematically researched different laser parameters influencing the surface status of microchannels and obtained optimized etching parameters. We investigated and optimized the organic solution composition of PMMA while casting chip masters, and developed a method to form fine polymer masters using two different viscosity solutions to cast the model in turn, and studied the repeatable replication. Then, we investigated physical performance of this chip and evaluated the practicability by analyzing Rhodamine B. Compared with present methods, the proposed method does not need photolithography on photoresistant and chemical etching. The entire fabricating progress is simple, fast, low-cost and can be controlled easily. Only several minutes are required to make a metal model, 3 hours for a PMMA master, and one day for PDMS chips.展开更多
Gamma-ray radiation has always been a convenient and effective way to modify the inter- facial properties in polymer blends. In this work, a small amount of trimethylolpropane triacrylate （TMPTA） was incorporated in...Gamma-ray radiation has always been a convenient and effective way to modify the inter- facial properties in polymer blends. In this work, a small amount of trimethylolpropane triacrylate （TMPTA） was incorporated into poly（ethylene terephthalate） （PET）/random terpolymer elastomer （ST2000） blends by melt-blending. The existence of TMPTA would induce the crosslinking of PET and ST2000 molecular chains at high temperatures of blend- ing, resulting in the improvement in the impact strength but the loss in the tensile strength. When the PET/ST2000 blends were irradiated by gamma-ray radiation, the integrated me- chanical properties could be enhanced significantly at a high absorbed dose. The irradiated sample at a dose of 100 kGy even couldn＇t be broken under the impact test load, and at the same time, has nearly no loss of tensile strength. Based on the analysis of the impact- fractured surface morphologies of the blends, it can be concluded that gamma-ray radiation at high absorbed dose can further in situ enhance the interfacial adhesion by promoting the crosslinking reactions of TMPTA and polymer chains. As a result, the toughness and strength of PET/ST2000 blend could be dramatically improved. This work provides a facial and practical way to the fabrication of polymer blends with high toughness and strength.展开更多
Because of the toxic effects of plasticizers, mainly the phthalate DEHP, the Children＇s Hospital Kinderklinik Glanzing in Vienna, Austria started in 2000 replacing PVC-containing medical devices by PVC-free material....Because of the toxic effects of plasticizers, mainly the phthalate DEHP, the Children＇s Hospital Kinderklinik Glanzing in Vienna, Austria started in 2000 replacing PVC-containing medical devices by PVC-free material. After analysis of suspected PVC-containing medical products a PVC input-output balance was established. Through linkage with the consumption data PVC-containing articles could be identified. PVC-free alternatives for medical use were searched as well by literature research as by questioning the manufactures. Then medical producers were asked to confirm PVC free articles. PVC content of invasive medical products could be reduced from 343 kg and 14.6 % weight in 2001 to 178 kg and 7.6% weight in 2010.展开更多
Vapor-liquid equilibrium data of hexamethyl disiloxane+vinyl acetate system at 101.3kPa were measured by using double circulating vapor-liquid equilibrium still.The thermodynamic consistency of the VLE data was examin...Vapor-liquid equilibrium data of hexamethyl disiloxane+vinyl acetate system at 101.3kPa were measured by using double circulating vapor-liquid equilibrium still.The thermodynamic consistency of the VLE data was examined by Herrington method.Experimental data was correlated by non-random two-liquid(NRTL),Wilson and universal quasichemical(UNIQUAC)parameter models.All the models satisfactorily correlated with the VLE data.The result showed that the NRTL model was the most suitable one to represent experimental data satisfactorily.The system had a minimum temperature azeotrope at 345.71 K and the mole azeotropic composition was 0.0541.展开更多
Molecularly imprinted polymers(MIPs)for solid-phase extraction and pre-concentration of esculetin have been successfully prepared by the bulk polymerization method using esculetin as a template molecule.Polymers of va...Molecularly imprinted polymers(MIPs)for solid-phase extraction and pre-concentration of esculetin have been successfully prepared by the bulk polymerization method using esculetin as a template molecule.Polymers of varying composition were prepared using different monomers(4-vinylpyridine,methacrylic acid,and acrylamide),ethylene glycol dimethacrylate as the cross-linker,2,2-azobis(2-methylpropinitrile)as the initiator,and different porogen solvents(ethanol,acetone/methanol,and acetonitrile).The best polymer was obtained when 4-vinylpyridine was used as the monomer and acetone/methanol(3:2)as the porogen solvent,whereas the template:-monomer:-cross-linker ratio was 1:4:20.The imprinting factor of the selected MIPs for esculetin was 3.77.The polymers were evaluated according to their selective recognition properties for esculetin and structurally-related compounds(esculin,scopoletin,coumarin,and 7-methoxycoumarin).Chemical and morphological characterizations of the polymers were investigated by FTIR and scanning electron microscope,which confirmed a high degree of polymerization.Surface area,pore volume,and pore size of the polymer were investigated by Brunauer-Emmett-Teller analysis.MIPs were also successfully used as solid-phase adsorbent materials for the extraction of esculetin from tobacco leaves.Esculetin contents in dried tobacco leaves were found to be(9.27±0.17)μg g-1.展开更多
Mass transfer and catalyst recovery are two crucial issues in solid base catalysis,while the cumbersome operation steps and the associated time and energy penalties are still inevitable for conventional catalysts.Achi...Mass transfer and catalyst recovery are two crucial issues in solid base catalysis,while the cumbersome operation steps and the associated time and energy penalties are still inevitable for conventional catalysts.Achieving the technical upgrades through catalyst design is desirable but challenging because of the difficulty in satisfying diverse demands of different steps.In this work,a magnetically responsive solid base catalyst with the rod-like nanostructure was developed.The rod-like solid base catalysts are composed of Fe_(3)O_(4) cores,silica shells and calcium oxide active sites.The functions of magnetic recovery and stirring were integrated into the catalyst,which applies in both the general catalytic processes and microchannel reactors given their nanoscales.When applied to the synthesis of dimethyl carbonate by onestep transesterification of methanol and ethylene carbonate,an apparent enhancement on turnover frequency value(33.1 h^(−1))was observed for nano-stirring compared with that tested without stirring(12.1 h^(−1))within 30 min.The present catalysts may open up new avenues in the development of advanced solid base catalysts.展开更多
文摘A facile and efficient diastereoselective synthesis of methyl 3β-hydroxyeudesmane-4,11(13)-dien-12-oicate starting from (+)-dihydrocarvone has been carried out in 9 steps at the first time.
文摘High-pressure vapor-liquid equilibrium data for the binary systems of methyl propionate＋carbon dioxide and propyl propionate＋carbon dioxide were measured at pressure from 1.00 MPa to 12.00 MPa and temperature in the range from 313 K to 373 K. Experimental results were correlated with the Peng-Robinson equation of state with the two-parameter van der Waals mixing rule. At the same time, the Henry＇s coefficient, partial molar enthalpy change and partial molar entropy change of CO2 during dissolution at different temperature were also calculated.
文摘为研究长叶香茶菜Rabdosia stracheyi(Benth ex Hook.)Hara的化学成分,本文采用硅胶、反相硅胶C 18、葡聚糖凝胶Sephadex LH-20、反相半制备高效液相等色谱方法对长叶香茶菜地上部分进行分离、纯化,利用1 H NMR、13 C NMR、HR-ESI-MS等波谱数据,结合参考文献,鉴定化合物的结构。结果表明,从长叶香茶菜地上部分分离得到12个三萜类化合物,它们分别是木栓醇(1)、齐墩果酸(2)、3β-羟基-齐墩果烷-11,13(18)-二烯-28酸(3)、2α,3α-二羟基齐墩果-12-烯-28酸(4)、2 a,3a,24-三羟基-12-烯-28-齐墩果酸(5)、2α,3β,24-三羟基齐墩果-12-烯-28酸(6)、cleistocalyxin(7)、熊果醇(8)、2α-羟基乌苏酸(9)、2a,3a,24-三羟基熊果-12,20(30)-二烯-28-酸甲酯(10)、maquatic acid(11)和2α,3α,24-三羟基-12,20(30)-二烯乌苏酸(12)。以上得到的三萜类化合物均为首次从该植物中分离得到。
基金Supported by the Program for New Century Excellent Talents in University (NCET-07-0738)
文摘Acrylonitrile-methyl methacrylate （AN-MMA） copolymer/silica nanocomposites were synthesized by in-situ emulsion polymerization initiated by 2,2＇-azobis（2-amidinopropane） dihydrochloride absorbed onto colloidal silica particles, and the mesoporous carbon materials were prepared through carbonization of the obtained AN-MMA copolymer/silica nanocomposites, followed by HF etching. Thermogravimetric analysis of AN-MMAcopolymer/silica nanocomposltes snoweO mat me caroon ylelCl or copolymer was slgnuy oecreaseo as Silica parucle incorporated. N2 adsorption-desorption, scan electron microscopy （SEM） and transmission electron microscopy （TEM） were used to characterize the structure and morphology of the mesoporous carbon materials. Both SEM and
文摘A kinetic model was developed to describe the atom transfer radical polymerization (ATRP) of 2(N,N-dimethylarnino) ethyl methacrylate (DMAEMA). The model was based on a polymerization mechanism, which included the atom transfer equilibrium for primary radical, the propagation of growing polymer radical, and the atom transfer equilibrium for the growing polymer radical. An experiment was carried out to measure the conversion of monomer, the number-average molecular weight of polymer and molecular weight distribution for the ATRP process of DMAEMA. The experimental data were used to correlate the kinetic model and rate constants were obtained. The rate constants of activation and deactivation in the atom transfer equilibrium for primary radical are 1.0 x 10(4) L(.)mol(-1.)s(-1) and 0.04 L(.)mol(-1.)s(-1), respectively. The rate constant of the propagation of growing polymer radical is 8.50 L(.)mol(-1.)s(-1), and the rate constants of activation and deactivation in the atom transfer equilibrium for growing polymer radical are 0.045 L(.)mol(-1.)s(-1) and 1.2 x 10(5) L(.)mol(-1.)s(-1), respectively. The values of the rate constants represent the features of the ATRP process. The kinetic model was used to calculate the ATRP process of DMAEMA. The results show that the calculations agree well with the measurements.
基金Funded by the Natural Science Foundation of China (No. 20775096)
文摘We proposed a novel method of fabricating polydimethylsiloxane (PDMS) microfluidic chip polymer master molds in this paper. The method mainly includes two steps. First, a stainless steel slice was laser etched to form a metal model. Then, the organic solution of poly(methyl methacrylate) (PMMA) was casted onto the metal model to fabricate the PMMA master which subsequently would be used to fabricate PDMS chips. We systematically researched different laser parameters influencing the surface status of microchannels and obtained optimized etching parameters. We investigated and optimized the organic solution composition of PMMA while casting chip masters, and developed a method to form fine polymer masters using two different viscosity solutions to cast the model in turn, and studied the repeatable replication. Then, we investigated physical performance of this chip and evaluated the practicability by analyzing Rhodamine B. Compared with present methods, the proposed method does not need photolithography on photoresistant and chemical etching. The entire fabricating progress is simple, fast, low-cost and can be controlled easily. Only several minutes are required to make a metal model, 3 hours for a PMMA master, and one day for PDMS chips.
文摘Gamma-ray radiation has always been a convenient and effective way to modify the inter- facial properties in polymer blends. In this work, a small amount of trimethylolpropane triacrylate （TMPTA） was incorporated into poly（ethylene terephthalate） （PET）/random terpolymer elastomer （ST2000） blends by melt-blending. The existence of TMPTA would induce the crosslinking of PET and ST2000 molecular chains at high temperatures of blend- ing, resulting in the improvement in the impact strength but the loss in the tensile strength. When the PET/ST2000 blends were irradiated by gamma-ray radiation, the integrated me- chanical properties could be enhanced significantly at a high absorbed dose. The irradiated sample at a dose of 100 kGy even couldn＇t be broken under the impact test load, and at the same time, has nearly no loss of tensile strength. Based on the analysis of the impact- fractured surface morphologies of the blends, it can be concluded that gamma-ray radiation at high absorbed dose can further in situ enhance the interfacial adhesion by promoting the crosslinking reactions of TMPTA and polymer chains. As a result, the toughness and strength of PET/ST2000 blend could be dramatically improved. This work provides a facial and practical way to the fabrication of polymer blends with high toughness and strength.
文摘Because of the toxic effects of plasticizers, mainly the phthalate DEHP, the Children＇s Hospital Kinderklinik Glanzing in Vienna, Austria started in 2000 replacing PVC-containing medical devices by PVC-free material. After analysis of suspected PVC-containing medical products a PVC input-output balance was established. Through linkage with the consumption data PVC-containing articles could be identified. PVC-free alternatives for medical use were searched as well by literature research as by questioning the manufactures. Then medical producers were asked to confirm PVC free articles. PVC content of invasive medical products could be reduced from 343 kg and 14.6 % weight in 2001 to 178 kg and 7.6% weight in 2010.
文摘Vapor-liquid equilibrium data of hexamethyl disiloxane+vinyl acetate system at 101.3kPa were measured by using double circulating vapor-liquid equilibrium still.The thermodynamic consistency of the VLE data was examined by Herrington method.Experimental data was correlated by non-random two-liquid(NRTL),Wilson and universal quasichemical(UNIQUAC)parameter models.All the models satisfactorily correlated with the VLE data.The result showed that the NRTL model was the most suitable one to represent experimental data satisfactorily.The system had a minimum temperature azeotrope at 345.71 K and the mole azeotropic composition was 0.0541.
基金supported by the Yunnan Green Tobacco Production Research(2011YN01)the China Equipment and Education Resources System(CERS-1-75)
文摘Molecularly imprinted polymers(MIPs)for solid-phase extraction and pre-concentration of esculetin have been successfully prepared by the bulk polymerization method using esculetin as a template molecule.Polymers of varying composition were prepared using different monomers(4-vinylpyridine,methacrylic acid,and acrylamide),ethylene glycol dimethacrylate as the cross-linker,2,2-azobis(2-methylpropinitrile)as the initiator,and different porogen solvents(ethanol,acetone/methanol,and acetonitrile).The best polymer was obtained when 4-vinylpyridine was used as the monomer and acetone/methanol(3:2)as the porogen solvent,whereas the template:-monomer:-cross-linker ratio was 1:4:20.The imprinting factor of the selected MIPs for esculetin was 3.77.The polymers were evaluated according to their selective recognition properties for esculetin and structurally-related compounds(esculin,scopoletin,coumarin,and 7-methoxycoumarin).Chemical and morphological characterizations of the polymers were investigated by FTIR and scanning electron microscope,which confirmed a high degree of polymerization.Surface area,pore volume,and pore size of the polymer were investigated by Brunauer-Emmett-Teller analysis.MIPs were also successfully used as solid-phase adsorbent materials for the extraction of esculetin from tobacco leaves.Esculetin contents in dried tobacco leaves were found to be(9.27±0.17)μg g-1.
基金supported by the National Natural Science Foundation of China Youth Project(21808110)the financial support of this work by the National Science Fund for Distinguished Young Scholars(22125804)the National Natural Science Foundation of China(21878149,22078155,and 21722606)。
文摘Mass transfer and catalyst recovery are two crucial issues in solid base catalysis,while the cumbersome operation steps and the associated time and energy penalties are still inevitable for conventional catalysts.Achieving the technical upgrades through catalyst design is desirable but challenging because of the difficulty in satisfying diverse demands of different steps.In this work,a magnetically responsive solid base catalyst with the rod-like nanostructure was developed.The rod-like solid base catalysts are composed of Fe_(3)O_(4) cores,silica shells and calcium oxide active sites.The functions of magnetic recovery and stirring were integrated into the catalyst,which applies in both the general catalytic processes and microchannel reactors given their nanoscales.When applied to the synthesis of dimethyl carbonate by onestep transesterification of methanol and ethylene carbonate,an apparent enhancement on turnover frequency value(33.1 h^(−1))was observed for nano-stirring compared with that tested without stirring(12.1 h^(−1))within 30 min.The present catalysts may open up new avenues in the development of advanced solid base catalysts.
