A yellow crosslinking polymeric dye was prepared by grafting the flavone moiety containing azo chromophore onto polyvinylamine backbone.The λ max of this polymeric dye in water is 382 nm.The polymeric dye is fixed to...A yellow crosslinking polymeric dye was prepared by grafting the flavone moiety containing azo chromophore onto polyvinylamine backbone.The λ max of this polymeric dye in water is 382 nm.The polymeric dye is fixed to silk and cotton with a crosslinking agent,2-chloro-4,6-di(aminobenzene-4'-β-sulphatoethylsulphone)-1,3,5-s-triazine,which acts as a bridge between the fiber and dye molecules.The fixation of this polymeric dye reaches 99% and the dyed samples exhibit excellent rubbing and washing fastness.展开更多
The electrical and thermal performances of a simulated 60 kW Proton Exchange Membrane Fuel Cell (PEMFC) cogeneration system are first analyzed and then strategies to make the system operation stable and efficient are ...The electrical and thermal performances of a simulated 60 kW Proton Exchange Membrane Fuel Cell (PEMFC) cogeneration system are first analyzed and then strategies to make the system operation stable and efficient are developed. The system configuration is described first, and then the power response and coordination strategy are presented on the basis of the electricity model. Two different thermal models are used to estimate the thermal performance of this cogeneration system, and heat management is discussed. Based on these system designs, the 60 kW PEMFC cogeneration system is analyzed in detail. The analysis results will be useful for further study and development of the system.展开更多
Mesoporous SiO_2 microspheres were synthesized using the sol-gel method and were characterized by TEM, FT-IR and BET techniques. The diameter of the microspheres is about 100—150 nm, and the average mesopore diameter...Mesoporous SiO_2 microspheres were synthesized using the sol-gel method and were characterized by TEM, FT-IR and BET techniques. The diameter of the microspheres is about 100—150 nm, and the average mesopore diameter is 2.55 nm, while the specific surface area is 1 088.9 m2/g. Mesoporous SiO_2 microspheres adsorb glutaraldehyde and immobilize laccase by means of the aldehyde group in glutaral which can react with the amidogen of laccase. The immobilization conditions were optimized at a glutaraldehyde concentration of 0.75%, a crosslinking time of 8 h, a laccase concentration of 0.04 L/L and an immobilization time of 10 h. When diesel leakage concentration was 80 mg/L, the highest corrosion inhibition efficiency of immobilized laccase reached 49.23%, which was slightly lower than the corrosion inhibition efficiency of free laccase(59%). The diesel degradation ratio could reach up to 45%. It has been proved that the immobilized laccase could degrade diesel to inhibit corrosion.展开更多
Due to the increasing demand of replacing large capacity overhead lines with underground cables in Korea, KEPCO （Korea Electric Power Corporation） and LS Cable （LS Cable ＆ System） have developed 345 kV optical fi...Due to the increasing demand of replacing large capacity overhead lines with underground cables in Korea, KEPCO （Korea Electric Power Corporation） and LS Cable （LS Cable ＆ System） have developed 345 kV optical fiber composite XLPE （cross-linked polyethylene） 2,500 mm2 cable system. This system has been installed in Cheongna district of Incheon city. KEPCO and LS Cable are also planning to build the cooling system in a tunnel in order to reduce the ambient temperature caused by currents. In this paper, the process of development, field installation, and final inspection test of the complete system will be described.展开更多
A controlled cross-linking polymerization containing intra- and intermolecular reactions was designed based on random coil morphology of macromolecules in solution. The soluble intramolecular cross-linked maeromolecu...A controlled cross-linking polymerization containing intra- and intermolecular reactions was designed based on random coil morphology of macromolecules in solution. The soluble intramolecular cross-linked maeromolecule （ICM） was successfully synthesized in the system with PVA and MDI. We found an especial dissolving phenomenon, namely the semi-soluble phenomenon when some gels dissolved in DMF. The chain growth process of ICMs was investigated by Transmission electron microscopy （TEM） pictures of samples at different reacting times, in addition, TEM pictures show ICMs have three kinds of styles in structure, viz. ＂globule structure＂, ＂nubby structure＂ and the intervenient between the above two structures, and the efflux time of the ICMs was measured by an Ubbelohde viscosimeter, it was found that the efflux time decreases with the degree ofcrosslink increasing.展开更多
Objective To assess the microleakage of Class V restorations made with two resin-modified glass ionomer cements （RMGICs） and two polyacid-modified composite resins （PMCRs）. Methods Restorations of the four materia...Objective To assess the microleakage of Class V restorations made with two resin-modified glass ionomer cements （RMGICs） and two polyacid-modified composite resins （PMCRs）. Methods Restorations of the four materials （ GC Fuji Ⅱ LC, Vitremer^TM, Dyract AP and F2000^TM ） were placed in facial Class V cavity preparations in forty noncarious human molar teeth. Teeth were randomly assigned to 4 experimental groups of 10 teeth each. After thermal cycling（ ×20, 5 -55℃ ） , the interface between dentin and restorations was spattercoated with gold and observed under scanning electron microscopy （SEM）. Then the square and average width of margin gaps of central 1/3 interface were recorded with image analysis software. Results The data indicated no significant differences between all the restorative materials for both occlusal and gingival margins. Further analysis revealed there were statistically significant differences between occlusal margins and gingival margins for VitremerTM and Dyract AP, respectively. Conclusion None of the tested materials guaranteed margins free of microleakage. Resin-modified glass ionomer cements showed similar margin gaps to the polyacid-modified composite resins tested.展开更多
A novel crosslinkable water/alcohol soluble conjugated polymer PFN-C containing oxetane groups and aminoalkyl groups in the side chains has been developed and used as highly efficient electron injection and transporti...A novel crosslinkable water/alcohol soluble conjugated polymer PFN-C containing oxetane groups and aminoalkyl groups in the side chains has been developed and used as highly efficient electron injection and transporting material for polymer light-emitting diodes (PLEDs). The unique solubility in polar solvents and crosslinkable ability of PFN-C render it a good can- didate for solution processed multilayer PLEDs. It was found that PFN-C can greatly enhance the electron injection from high work-function metal cathode, due to its pendant amino groups. As a result, PLEDs with PFN-C/Al cathode exhibited compara- ble device performance to the devices with Ba/Al cathode. The resulting green light-emitting device showed promising perfor- mance with a maximum luminance efficiency of 13.53 cd A-1.展开更多
In this work,azobenzene-containing polyurethane liquid crystal networks(PULCN(AZO)s)were synthesized using a one-pot strategy to demonstrate excellent two-way free-standing thermo-/photo-responsive shape memory effect...In this work,azobenzene-containing polyurethane liquid crystal networks(PULCN(AZO)s)were synthesized using a one-pot strategy to demonstrate excellent two-way free-standing thermo-/photo-responsive shape memory effects.Based on the step-growth nature of hydroxyls and isocyanates,the architectures of the networks were adjusted by controlling the stoichiometries of chemical materials.A uniform monodomain sample was prepared by external stress relaxation via a reversible addition reaction of a dynamic carbamate bond.Two independent transition temperatures assigned to glass transition temperature/melting temperature and liquid crystal phase transition temperature were employed to thermally trigger triple shape memory effects and two-way autonomous actuation.In addition,taking advantage of the trans-cis photoisomerization of azobenzene,the programmed network showed a reversible bending and unbending shape change upon irradiation by visible light at450 and 550 nm,respectively.Coupling the autonomously thermo-induced contraction/extension actuation and reversible photo-induced bending/unbending behaviors of PULCN(AZO)s in one system will expand their potential applications in emerging multifunctional devices.展开更多
Herein,a facile and highly efficient synthetic method to prepare organic photothermal materials with high photo-stability and outstanding photothermal performance is reported.Through direct polymerization of commercia...Herein,a facile and highly efficient synthetic method to prepare organic photothermal materials with high photo-stability and outstanding photothermal performance is reported.Through direct polymerization of commercial aromatic monomers in the presence of anhydrous aluminium chloride and dichloromethane,four kinds of conjugated microporous polymers(CMPs)were obtained.Detailed structural analysis confirmed that the resultant CMPs possessed abundant micropores with an extendedπ-conjugated skeleton.Under near-infrared(NIR)light irradiation(808 nm,1.0 W cm−2),all the CMPs showed fast heating-up behavior with their maximum temperatures higher than 150℃.Moreover,the efficiency of photothermal conversion(η)of the CMPs was found to increase linearly with the increase in the number of conjugated benzene rings within the monomer.Poly-TPE from tetraphenylethylene(TPE)and Poly-TP from o-terphenyl(TP)showed highηvalues of over 47%.Poly-TPE was additionally used as a photothermal filler to remotely and spatially control the shape recovery of thermal-sensitive shape memory polymers(SMPs),while its introduction(1 wt%)had little influence on the thermal and mechanical properties of the polymer matrixes.Owing to their excellent NIR photothermal performance as well as a one-step synthetic preparation,these CMPs may be promising photothermal materials for practical applications.展开更多
基金Supported by the National Natural Science Foundation of China （20804007） the State Key Laboratory of Fine Chemicals（KF1014）
文摘A yellow crosslinking polymeric dye was prepared by grafting the flavone moiety containing azo chromophore onto polyvinylamine backbone.The λ max of this polymeric dye in water is 382 nm.The polymeric dye is fixed to silk and cotton with a crosslinking agent,2-chloro-4,6-di(aminobenzene-4'-β-sulphatoethylsulphone)-1,3,5-s-triazine,which acts as a bridge between the fiber and dye molecules.The fixation of this polymeric dye reaches 99% and the dyed samples exhibit excellent rubbing and washing fastness.
基金Project (No. 2002AA517020) supported by the Hi-Tech Researchand Development Program (863) of China
文摘The electrical and thermal performances of a simulated 60 kW Proton Exchange Membrane Fuel Cell (PEMFC) cogeneration system are first analyzed and then strategies to make the system operation stable and efficient are developed. The system configuration is described first, and then the power response and coordination strategy are presented on the basis of the electricity model. Two different thermal models are used to estimate the thermal performance of this cogeneration system, and heat management is discussed. Based on these system designs, the 60 kW PEMFC cogeneration system is analyzed in detail. The analysis results will be useful for further study and development of the system.
基金supported by the Foundation for Top Talents Program of China University of Petroleum
文摘Mesoporous SiO_2 microspheres were synthesized using the sol-gel method and were characterized by TEM, FT-IR and BET techniques. The diameter of the microspheres is about 100—150 nm, and the average mesopore diameter is 2.55 nm, while the specific surface area is 1 088.9 m2/g. Mesoporous SiO_2 microspheres adsorb glutaraldehyde and immobilize laccase by means of the aldehyde group in glutaral which can react with the amidogen of laccase. The immobilization conditions were optimized at a glutaraldehyde concentration of 0.75%, a crosslinking time of 8 h, a laccase concentration of 0.04 L/L and an immobilization time of 10 h. When diesel leakage concentration was 80 mg/L, the highest corrosion inhibition efficiency of immobilized laccase reached 49.23%, which was slightly lower than the corrosion inhibition efficiency of free laccase(59%). The diesel degradation ratio could reach up to 45%. It has been proved that the immobilized laccase could degrade diesel to inhibit corrosion.
文摘Due to the increasing demand of replacing large capacity overhead lines with underground cables in Korea, KEPCO （Korea Electric Power Corporation） and LS Cable （LS Cable ＆ System） have developed 345 kV optical fiber composite XLPE （cross-linked polyethylene） 2,500 mm2 cable system. This system has been installed in Cheongna district of Incheon city. KEPCO and LS Cable are also planning to build the cooling system in a tunnel in order to reduce the ambient temperature caused by currents. In this paper, the process of development, field installation, and final inspection test of the complete system will be described.
文摘A controlled cross-linking polymerization containing intra- and intermolecular reactions was designed based on random coil morphology of macromolecules in solution. The soluble intramolecular cross-linked maeromolecule （ICM） was successfully synthesized in the system with PVA and MDI. We found an especial dissolving phenomenon, namely the semi-soluble phenomenon when some gels dissolved in DMF. The chain growth process of ICMs was investigated by Transmission electron microscopy （TEM） pictures of samples at different reacting times, in addition, TEM pictures show ICMs have three kinds of styles in structure, viz. ＂globule structure＂, ＂nubby structure＂ and the intervenient between the above two structures, and the efflux time of the ICMs was measured by an Ubbelohde viscosimeter, it was found that the efflux time decreases with the degree ofcrosslink increasing.
文摘Objective To assess the microleakage of Class V restorations made with two resin-modified glass ionomer cements （RMGICs） and two polyacid-modified composite resins （PMCRs）. Methods Restorations of the four materials （ GC Fuji Ⅱ LC, Vitremer^TM, Dyract AP and F2000^TM ） were placed in facial Class V cavity preparations in forty noncarious human molar teeth. Teeth were randomly assigned to 4 experimental groups of 10 teeth each. After thermal cycling（ ×20, 5 -55℃ ） , the interface between dentin and restorations was spattercoated with gold and observed under scanning electron microscopy （SEM）. Then the square and average width of margin gaps of central 1/3 interface were recorded with image analysis software. Results The data indicated no significant differences between all the restorative materials for both occlusal and gingival margins. Further analysis revealed there were statistically significant differences between occlusal margins and gingival margins for VitremerTM and Dyract AP, respectively. Conclusion None of the tested materials guaranteed margins free of microleakage. Resin-modified glass ionomer cements showed similar margin gaps to the polyacid-modified composite resins tested.
基金financially supported by the Natural Science Foundation of China (50990065, 51010003, 51073058 & 20904011)the National Basic Research Program of China (973 Program, 2009CB623601)the Fun-damental Research Funds for the Central Universities, South China Uni-versity of Technology
文摘A novel crosslinkable water/alcohol soluble conjugated polymer PFN-C containing oxetane groups and aminoalkyl groups in the side chains has been developed and used as highly efficient electron injection and transporting material for polymer light-emitting diodes (PLEDs). The unique solubility in polar solvents and crosslinkable ability of PFN-C render it a good can- didate for solution processed multilayer PLEDs. It was found that PFN-C can greatly enhance the electron injection from high work-function metal cathode, due to its pendant amino groups. As a result, PLEDs with PFN-C/Al cathode exhibited compara- ble device performance to the devices with Ba/Al cathode. The resulting green light-emitting device showed promising perfor- mance with a maximum luminance efficiency of 13.53 cd A-1.
基金supported financially by the National Natural Science Foundation of China(51773131 and 51721091)the Fundamental Research Funds for the Central Universities。
文摘In this work,azobenzene-containing polyurethane liquid crystal networks(PULCN(AZO)s)were synthesized using a one-pot strategy to demonstrate excellent two-way free-standing thermo-/photo-responsive shape memory effects.Based on the step-growth nature of hydroxyls and isocyanates,the architectures of the networks were adjusted by controlling the stoichiometries of chemical materials.A uniform monodomain sample was prepared by external stress relaxation via a reversible addition reaction of a dynamic carbamate bond.Two independent transition temperatures assigned to glass transition temperature/melting temperature and liquid crystal phase transition temperature were employed to thermally trigger triple shape memory effects and two-way autonomous actuation.In addition,taking advantage of the trans-cis photoisomerization of azobenzene,the programmed network showed a reversible bending and unbending shape change upon irradiation by visible light at450 and 550 nm,respectively.Coupling the autonomously thermo-induced contraction/extension actuation and reversible photo-induced bending/unbending behaviors of PULCN(AZO)s in one system will expand their potential applications in emerging multifunctional devices.
基金the National Natural Science Foundation of China(51503231 and 21374136)Guangdong Innovative and Entrepreneurial Research Team Program(2013S086)the Fundamental Research Funds for the Central Universities(17lgjc03 and 18lgpy04)。
文摘Herein,a facile and highly efficient synthetic method to prepare organic photothermal materials with high photo-stability and outstanding photothermal performance is reported.Through direct polymerization of commercial aromatic monomers in the presence of anhydrous aluminium chloride and dichloromethane,four kinds of conjugated microporous polymers(CMPs)were obtained.Detailed structural analysis confirmed that the resultant CMPs possessed abundant micropores with an extendedπ-conjugated skeleton.Under near-infrared(NIR)light irradiation(808 nm,1.0 W cm−2),all the CMPs showed fast heating-up behavior with their maximum temperatures higher than 150℃.Moreover,the efficiency of photothermal conversion(η)of the CMPs was found to increase linearly with the increase in the number of conjugated benzene rings within the monomer.Poly-TPE from tetraphenylethylene(TPE)and Poly-TP from o-terphenyl(TP)showed highηvalues of over 47%.Poly-TPE was additionally used as a photothermal filler to remotely and spatially control the shape recovery of thermal-sensitive shape memory polymers(SMPs),while its introduction(1 wt%)had little influence on the thermal and mechanical properties of the polymer matrixes.Owing to their excellent NIR photothermal performance as well as a one-step synthetic preparation,these CMPs may be promising photothermal materials for practical applications.
