Solute transmission in saturated ore heap was studied numerically and experimentally. The convection-diffusion equation (CDE) used to describe the mass transportation in porous media was solved by characteristic diffe...Solute transmission in saturated ore heap was studied numerically and experimentally. The convection-diffusion equation (CDE) used to describe the mass transportation in porous media was solved by characteristic difference method to give the distribution of the concentration of ferrous ion in the ore column. To calibrate the computational model, a column test was performed using infiltration of sulfide ferrous solution (the initial concentration is c0=0.04 mol/L) on a 100 cm high column composed of ore particles smaller than 10 mm for 2.5 h. The numerical analysis shows that the results obtained from numerical modeling under the same operating conditions as used for column test are in good agreement with those from experimental procedure on the whole trend, which indicates that the model, the numerical method, and the parameters chosen can reflect the rule of ferrous ion transmission in ore heap.展开更多
Computer simulation models are widely applied in various areas of the health care sector, including the spread of infectious diseases. Patch models involve explicit movements of people between distinct locations. The ...Computer simulation models are widely applied in various areas of the health care sector, including the spread of infectious diseases. Patch models involve explicit movements of people between distinct locations. The aim of the present work has been designed and explored a patch model with population mobility between different patches and between each patch and an external population. The authors considered a SIR （susceptible-infected-recovered） scheme. The model was explored by computer simulations. The results show how endemic levels are reached in all patches of the system. Furthermore, the performed explorations suggest that the people mobility between patches, the immigration from outside the system and the infection rate in each patch, are factors that may influence the dynamics of epidemics and should be considered in health policy planning.展开更多
The new mechanism of drum-shaped gear with ring-involute teeth is presented to implement dimensional transmission for the stairlift. The structure of the gear and rack in this actuating mechanism is designed, and then...The new mechanism of drum-shaped gear with ring-involute teeth is presented to implement dimensional transmission for the stairlift. The structure of the gear and rack in this actuating mechanism is designed, and then its inherent radius of turn and modulus selection have been studied. In order to make the mechanism move steadily, the drive guide is proposed. After using the dynamics simulation software ADAMS to analyze the 3D model, this kind of mechanism is confirmed to be able to implement dimensional track. The useful method and basis would be provided for the optimization design of the mechanism.展开更多
Towing tractor drivelines are lightly damped non-linear systems. Interactions between components can cause dynamic behavors such as gear gap impact in gear transmissions, shuffle and clonk phenomena in driveline. The ...Towing tractor drivelines are lightly damped non-linear systems. Interactions between components can cause dynamic behavors such as gear gap impact in gear transmissions, shuffle and clonk phenomena in driveline. The torsional vibration of driveline has an important effect on grand engineering vehicle vibration and noise. Through analyzing torsional vibration equations of driveline, torsional vibration model of driveline is developed by using Matlab/Simulink software, Shuffle and clonk phenomena are observed in torsional vibration. The modeling method of analysizing driveline torsional vibration can be used to research and improve similar engineering vehicle driveline behavors.展开更多
In order to increase the productivity of microreactors, the parallelization of the microreactors is required. The performances of flow distributors can affect the product yield and fault detection ability when blockag...In order to increase the productivity of microreactors, the parallelization of the microreactors is required. The performances of flow distributors can affect the product yield and fault detection ability when blockage happens.In this research, an optimal design method to calculate the channel diameters and to determine the flow sensor location is derived based on mass balance and pressure balance models of split-and-recombine-type flow distributors(SRFDs). The model accuracy is verified by experiment data. The proposed method is applied to optimal design of SRFDs under constant flow rate operation conditions. The maximum angle difference between normal and blockage conditions at one sensor to those at the other sensors is set to be the objective function and the uniformity of flow distribution in microreactors under normal condition is also required. The diameters of each pipe in SRFDs are selected as the design variables. Simulated annealing algorithm is used to solve the optimization problem. The effectiveness of the optimal design results is demonstrated by fluid dynamics simulations. The results show that using the optimal channel diameters of SRFDs, the pressure drop in SRFD section is lower than that of the microreactor section. Meanwhile, in the case studies, only a few sensors that are located inside the SRFDs can easily detect the blockage abnormal condition in the parallelized microreactor system.展开更多
Multi-dimensional heat transfers modeling is crucial for building simulations of insulated buildings,which are widely used and have multi-dimensional heat transfers characteristics.For this work,state-model-reduction ...Multi-dimensional heat transfers modeling is crucial for building simulations of insulated buildings,which are widely used and have multi-dimensional heat transfers characteristics.For this work,state-model-reduction techniques were used to develop a reduced low-order model of multi-dimensional heat transfers.With hot box experiment of hollow block wall,heat flow relative errors between experiment and low-order model predication were less than 8% and the largest errors were less than 3%.Also,frequency responses of five typical walls,each with different thermal masses or insulation modes,the low-order model and the complete model showed that the low-order model results agree very well in the lower excitation frequency band with deviations appearing only at high frequency.Furthermore,low-order model was used on intersection thermal bridge of a floor slab and exterior wall.Results show that errors between the two models are very small.This low-order model could be coupled with most existing simulation software for different thermal mass envelope analyses to make up for differences between the multi-dimensional and one-dimensional models,simultaneously simplifying simulation calculations.展开更多
基金Project(06JJ30024) supported by the Natural Science Foundation of Hunan Province, ChinaProject(2004CB619206) supported by the Major State Basic Research and Development Program of China+1 种基金Project(50321402) supported by the National Science Fund for Innovative Research Groups of ChinaProject(06B052) supported by the Scientific Research Fund of Hunan Provincial Education Department of China
文摘Solute transmission in saturated ore heap was studied numerically and experimentally. The convection-diffusion equation (CDE) used to describe the mass transportation in porous media was solved by characteristic difference method to give the distribution of the concentration of ferrous ion in the ore column. To calibrate the computational model, a column test was performed using infiltration of sulfide ferrous solution (the initial concentration is c0=0.04 mol/L) on a 100 cm high column composed of ore particles smaller than 10 mm for 2.5 h. The numerical analysis shows that the results obtained from numerical modeling under the same operating conditions as used for column test are in good agreement with those from experimental procedure on the whole trend, which indicates that the model, the numerical method, and the parameters chosen can reflect the rule of ferrous ion transmission in ore heap.
文摘Computer simulation models are widely applied in various areas of the health care sector, including the spread of infectious diseases. Patch models involve explicit movements of people between distinct locations. The aim of the present work has been designed and explored a patch model with population mobility between different patches and between each patch and an external population. The authors considered a SIR （susceptible-infected-recovered） scheme. The model was explored by computer simulations. The results show how endemic levels are reached in all patches of the system. Furthermore, the performed explorations suggest that the people mobility between patches, the immigration from outside the system and the infection rate in each patch, are factors that may influence the dynamics of epidemics and should be considered in health policy planning.
文摘The new mechanism of drum-shaped gear with ring-involute teeth is presented to implement dimensional transmission for the stairlift. The structure of the gear and rack in this actuating mechanism is designed, and then its inherent radius of turn and modulus selection have been studied. In order to make the mechanism move steadily, the drive guide is proposed. After using the dynamics simulation software ADAMS to analyze the 3D model, this kind of mechanism is confirmed to be able to implement dimensional track. The useful method and basis would be provided for the optimization design of the mechanism.
文摘Towing tractor drivelines are lightly damped non-linear systems. Interactions between components can cause dynamic behavors such as gear gap impact in gear transmissions, shuffle and clonk phenomena in driveline. The torsional vibration of driveline has an important effect on grand engineering vehicle vibration and noise. Through analyzing torsional vibration equations of driveline, torsional vibration model of driveline is developed by using Matlab/Simulink software, Shuffle and clonk phenomena are observed in torsional vibration. The modeling method of analysizing driveline torsional vibration can be used to research and improve similar engineering vehicle driveline behavors.
基金Supported by the National Natural Science Foundation of China(21466026,61364009)NJZZ(14054)
文摘In order to increase the productivity of microreactors, the parallelization of the microreactors is required. The performances of flow distributors can affect the product yield and fault detection ability when blockage happens.In this research, an optimal design method to calculate the channel diameters and to determine the flow sensor location is derived based on mass balance and pressure balance models of split-and-recombine-type flow distributors(SRFDs). The model accuracy is verified by experiment data. The proposed method is applied to optimal design of SRFDs under constant flow rate operation conditions. The maximum angle difference between normal and blockage conditions at one sensor to those at the other sensors is set to be the objective function and the uniformity of flow distribution in microreactors under normal condition is also required. The diameters of each pipe in SRFDs are selected as the design variables. Simulated annealing algorithm is used to solve the optimization problem. The effectiveness of the optimal design results is demonstrated by fluid dynamics simulations. The results show that using the optimal channel diameters of SRFDs, the pressure drop in SRFD section is lower than that of the microreactor section. Meanwhile, in the case studies, only a few sensors that are located inside the SRFDs can easily detect the blockage abnormal condition in the parallelized microreactor system.
基金Project(51178023)supported by the National Natural Science Foundation of China
文摘Multi-dimensional heat transfers modeling is crucial for building simulations of insulated buildings,which are widely used and have multi-dimensional heat transfers characteristics.For this work,state-model-reduction techniques were used to develop a reduced low-order model of multi-dimensional heat transfers.With hot box experiment of hollow block wall,heat flow relative errors between experiment and low-order model predication were less than 8% and the largest errors were less than 3%.Also,frequency responses of five typical walls,each with different thermal masses or insulation modes,the low-order model and the complete model showed that the low-order model results agree very well in the lower excitation frequency band with deviations appearing only at high frequency.Furthermore,low-order model was used on intersection thermal bridge of a floor slab and exterior wall.Results show that errors between the two models are very small.This low-order model could be coupled with most existing simulation software for different thermal mass envelope analyses to make up for differences between the multi-dimensional and one-dimensional models,simultaneously simplifying simulation calculations.
