Zn/H-ZS M-5轻烃芳构化催化剂中Zn与分子筛协同作用的研究

分析了Al2 O3 的加入引起Zn/H ZSM 5催化剂芳构化活性和选择性下降以及稳定性有所改善的原因在于高温焙烧或水热处理 ,使掺有粘结剂氧化铝的Zn/H ZSM 5催化剂表面锌组元的再分布 ,即Al2 O3 上的锌含量增加 ,而处于H ZSM 5沸石上的锌浓度降低。较为系统地探讨了Al2 O3 和ZnO/Al2 O3 的芳构化催化作用以及锌组元和ZnO/Al2 O3的引入对HZSM 5性能的影响。论证了在Zn/H ZSM 5催化剂中只有处于分子筛表面的Zn组元才能同分子筛B酸中心产生协同作用 ,从而改善H ZSM 5分子筛的芳构化活性与选择性 ,而在经过焙烧和水热处理的混有Al2 O3 的Zn/H ZSM 5催化剂中 ,分布在Al2 O3 上的锌组元几乎不与分子筛发生协同作用 。

An Innovative Hullform Design Technique for Low Carbon Shipping

Combining modem Computational Fluid Dynamics （CFD） evaluator with optimization method, a new approach of hullform design for low carbon shipping is presented. Using the approach, the designers may find the minimum of some user-defined objective functions under constrains. An example of the approach application for a surface combatant hull optimization is demonstrated. In the procedure, the Particle Swarm Optimization （PSO） algorithm is adopted for exploring the design space, and the Bezier patch method is chosen to automatically modify the geometry of bulb. The total resistance is assessed by RANS solvers. It＇s shown that the total resistance coefficient of the optimized design is reduced by about 6.6% comparing with the original design. The given combatant design optimization example demonstrates the practicability and superiority of the proposed approach for low carbon shipping.

Calculation of Apparent Activation Energy of Coal Oxidation at Low Temperatures by Measuring CO Yield

By analyzing previous studies on activation energy of coal oxidation at low temperatures, a theoretical calculation model of apparent activation energy is established. Yield of CO is measured by using the characteristic detector of coal oxidation at 30-90 ℃. The impact of parameters, such as airflow and particle size, on activation energies is analyzed. Finally, agreement was obtained between activation energies and the dynamic oxygen absorbed in order to test the accuracy of the model. The results show that： 1） a positive exponential relation between concentration of CO and temperature in the process of the experiment is obtained： increases are almost identical and the initial CO is low; 2） the apparent activation energies increase gradually with the sizes of particle at the same airflow, but the gradients increase at a decreasing rate; 3） the apparent activation energies increase linearly with airflow. For the five coal particles, the differences among the energies are relatively high when the airflow was low, but the differences were low when the airflow was high; 4） the optimum sizes of particle, 0.125-0.25 ram, and the optimum volume of airflow, 100 mL/min, are determined from the model; 5） the apparent activation energies decrease with an increase in oxygen absorbed. A negative exponential relation between the two is obtained,

Fabrication of cast carbon steel with ultrafine TiC particles

The carbon steels dispersed with ultrafine TiC particles were fabricated by conventional casting method. The casting process is more economical than other available routes for metal matrix composite production, and the large sized components to be fabricated in short processing time. However, it is extremely difficult to obtain uniform dispersion of ultrafine ceramic particles in liquid metals due to the poor wettability and the specific gravity difference between the ceramic particle and metal matrix. In order to solve these problems, the mechanical milling (MM) and surface-active processes were introduced. As a result, Cu coated ultrafine TiC powders made by MM process using high energy ball milling machine were mixed with Sn powders as a surfactant to get better wettability by lowering the surface tension of carbon steel melt. The microstructural investigations by OM show that ultrafine TiC particles are distributed uniformly in carbon steel matrix. The grain sizes of the cast matrix with ultrafine TiC particles are much smaller than those without ultrafine TiC particles. This is probably due to the fact that TiC particles act as nucleation sites during solidification. The wear resistance of cast carbon steel composites added with MMed TiC/Cu-Sn powders is improved due to grain size refinement.

Experimental Investigation of a Cryogenic Filter for Separating Solid Carbon Dioxide Particles from Liquid Nitrogen

This paper presents an investigation of a new method of purifying cryogenic liquid using sintered metallic wire-mesh filter, which has the advantages of high purifying efficiency and preferred strength at absolutely low temperature. Experiments are conducted to purify solid CO2 particles from liquid nitrogen. Temperature and pressure in the upstream and downstream of the filter, and the flow rate of carbon dioxide （CO2） gas and liquid nitrogen are measured, with the gas content of filtrate analyzed using a CO2 concentration detector. It is illustrated that after filtration, the purity of liquid nitrogen （volume fraction） is higher than 99.99%, which means that the volume fraction of CO2 is less than 0.01%. Effects of operation parameters on the performance of the filter, such as pressure drop Ap and filtration efficiency E are analyzed quantitatively. The present conclusions will provide a guideline to the optimumal design and operation of sintered metallic wire-mesh filter in cryogenic application.