等离子喷涂HA/Ti复合涂层研究 Ⅱ.生物学性能

对等离子喷涂 ＨＡ／Ｔｉ复合涂层进行模拟体液和体外细胞试验，以考察涂层的生物学性能，结果指出，涂层经模拟体液浸泡后，表面覆盖一层碳酸磷灰石（ｃａｒｂｏｎａｔｅ－ａｐａｔｉｔｅ），这表明涂层具有良好的生物活性．粗糙的涂层表面易于形成碳酸磷灰石．模拟体液的浓度太小或ＰＨ值太大，均会导致碳酸磷灰石层不能在涂层表面形成．体外细胞试验显示，成骨细胞能在涂层表面紧密贴壁并正常生长，显示涂层具有优良的生物相容性．

Experiments on decolourization with 122-resin for extraction of gib-berellins from solid medium under different conditions

The extracting liquid of gibberellins (Gibberella fujikuroi) from solid medium for was decolorized separately with 75%, 95% alcohol, and distilled water in static adsorption and vibrating way for different durations. The results showed that the content of GA3 in efflux extracted with alcohol is 10% higher than that with distilled water. With the increase of the durations of extraction, the content of GA3 increases and the dissolution of pigments also increase. For extraction of GA3 cultured in solid medium, the best decolorizing result was obtained when it was extracted with 75%-95% alcohol in static way for 1-3 h, or in a vibrating way for 30-60 min, and then to decolor in a static way for 30-60 min in 122 resin column.

Analysis of semi-solid response under rapid compression tests using multi-scale modelling and experiments

Simulating semi-solid metal forming requires modelling semi-solid behaviour.However, such modelling is difficult because semi-solid behavior is thixotropic and depends on the liquid-solid spatial distribution within the material.In order to better understand and model relationships between microstructure and behavior, a model based on micromechanical approaches and homogenisation techniques is presented.This model is an extension of a previous model established in a pure viscoplastic framework to account for elasticity.Indeed, experimental load-displacement signals reveal the presence of an elastic-type response in the earlier stages of deformation when semi-solids are loaded under rapid compression.This elastic feature of the behaviour is attributed to the response of the porous solid skeleton saturated by incompressible liquid.A good quantitative agreement is found between the elastic-viscoplastic predicted response and the experimental data.More precisely, the strong initial rising part of the load-displacement curve, the peak load and the subsequent fall in load are well captured.The effect of solid fraction on mechanical response is in qualitative agreement with experiments.

The research of the evaluation system for the sealability of hydraulic supports and jacks＇ seals

In order to enhance the sealing quality and assemble efficiency of hydraulic supports, the evaluation system for the sealability of the hydraulic support and jack＇s seals was established through the testing and experimenting technology in respects, such as seals＇ dimensions, reasonable amounts of compression, sealability, life, resistance to pressure, etc. Through life detecting test of the seal, found the longest life seal ring under the same conditions, and through the reciprocating test of the hydraulic support, found the most appropriate amount of interference between the groove and the seal ring, thus, to decrease the leakage and extend the life span of the hydraulic support.

Work characteristic analysis of single-rod symmetric cylinders

Hydraulic cylinders are divided into single-rod asymmetric cylinders and double-rod symmetric cylinders. The single-rod asymmetric cylinder has the advantages of small size and simple structure,but its speed characteristic is not symmetric. The double rod symmetric cylinder has the characteristic of symmetric speed,but it cannot be used in some special occasions. In this paper,one special hydraulic cylinder,a single-rod symmetric cylinder,is developed. Firstly,characters of this type of cylinder are introduced. Then,the system model is constructed by using one software which is Simulation X. Moreover,one single rod asymmetric cylinder is designed and the test rig using the symmetric valve to control single-rod symmetric or asymmetric cylinder is constructed. Both of the simulation and experimental results show that the symmetric valve control single-rod symmetric cylinder servo system is of symmetric speed characteristic,which can be used in practical occasion.

Experimental and simulation study of nylon 6 solid–liquid extraction process

The solid–liquid extraction process of nylon 6 to eliminate small molecules, i.e., caprolactam(CL), cyclic dimers(CD) and cyclic trimers(CT), is investigated in detail by both batch extraction experiments and numerical simulations. In the batch extraction experiments, due to the small molecules attaching to the polymeric surface, the basic physical mechanism shifts from surface diffusion to internal diffusion as the extraction proceeded. The experimental data are well reproduced by a diffusion model consisting of two distinct steps, characterized as surface diffusion and internal diffusion. Furthermore, based on the established mass transfer mechanism and diffusion model of the two distinct steps, the equilibrium constants and internal diffusion coefficients of CL, CD and CT are acquired. An industrial countercurrent extraction tower is further simulated. It is found that the extraction efficiency of CL can be significantly improved by increasing the temperature at the bottom portion of the tower. The elimination of CD, which can be greatly promoted by a high-concentration CL-water solution, is controlled by mass transfer resistance, whereas the removal of CL is mainly affected by the equilibrium.

Equilibrium of liquid-liquid extraction of 2-phenylbutyric acid enantiomers: Experiment and model

The utilization of liquid–liquid extraction for the separation of 2-phenylbutyric acid（2-PBA） enantiomers was proposed. Factors affecting the extract process were investigated, including organic solvents, β-cyclodextrin derivatives, cyclodextrin concentration, p H and temperature. A model was proposed to describe the separation process based on the homogeneous phase reaction mechanism. Important parameters of this model were determined experimentally. The physical distribution coefficients for molecular and ionic 2-PBA were0.129 and 7.455, respectively. The equilibrium constants of the complexation reactions were 89.36 and36.78 L·mol^-1 for（＋）-and（-）-2-PBA, respectively. The model was verified by experiments and proved to be an excellent means to optimize the separation system. Through modeling prediction and experiment, the best conditions（e.g., pH value of 3.00, extractant concentration of 0.1 mol·L^-1, temperature of 5.0 ℃） were acquired. Under this condition, the maximum enantioselectivity（2.096） was obtained.

Resilient Modulus of Hydraulically Bound Road Base Materials with High Volume Waste Dust

The paper presents laboratory test results on hydraulically bound road base materials containing high volume of steel slag and blast furnace slag waste dusts compared with control mixtures. These mixtures contain higher levels of （4mm-0.0 mm） dust, than would be the case in standard un bound road base mixtures. The combined influence of the steel slag and granulated blast furnace slag wastes content is to enhance the stiffness of the road base materials and save materials and cost during road construction. Triaxial repeated load tests were performed on the unbound and lightly bound materials to measure their resilient modulus. The test results show important improvements in the bond strength between the contents of road base materials. This offers the prospect of using these materials in road base materials to reduce the use of primary aggregates and thus minimize the cost of roads and highways construction.

The Effect of Bridging Liquid Surface Tension and Specific Surface Area on Strength Factor of Coal Agglomerates

The aim of this research is to determine the effect of bridging liquid surface tension and specific surface area on strength factor of coal agglomerates. The production of coal agglomerates of the range 15-27.51 mm was achieved. The crushing strength of the agglomerates was determined for good handling of fine （coal-liquid mixture） to improve fugitive dust control, decrease in transportation losses, reduce risk of coal freezing, lower risk of spontaneous combustion, etc. in iron and steel industries, railway corporations and coal corporations. Kerosene （paraffin oil） was used as a binder and the agglomerated coal oil mixture was pelletized using balling technique （disc）. Mechanical and physical tests like compressive strength test, etc. were carried out. The relationship between the bridging liquid surface tension and specific surface area on strength factor of coal agglomerates showed that there is considerable variation in these parameters in the coal powder systems.

Comparison of dissolution profile characteristics of 11 berberine hydrochloride tablet brands in different dissolution media

Berberine hydrochloride is commonly used to treat bacterial dysentery,gastroenteritis and other diseases.Many manufacturers are available on the market today,while the production process and formulation are quite different,which may directly affect the therapeutic effect of the drug.To this end,11 different production producers of berberine hydrochloride tablets were collected according to the pharmacopeia berberine hydrochloride dissolution method(basket method).In addition the dissolution process was carried out in four elution media with different pH,and the difference was similar(f2).Factors were calculated to evaluate in vitro dissolution requirements,and in vitro dissolution of different manufacturers of berberine hydrochloride tablets was determined by high performance liquid chromatography(HPLC).The method was verified by linearity,precision,stability and robustness.Based on the f2 value,there was a significant difference in the dissolution behavior of the formulations of most berberine hydrochloride tablet brands.This research provided the basis for further in-depth research in the later period.Although the drug specifications(0.1 g)were the same,the dissolution curve was different.This phenomenon may be attributed to the fact that the excipients and crystal form of the tablets affected the release and dissolution of the tablets in vitro.

Hurdles of CAR-T cell-based cancer immunotherapy directed against solid tumors

Recent reports on the impressive efficacy of chimeric antigen receptor(CAR)-modified T cells against hematologic malignancies have inspired oncologists to extend these efforts for the treatment of solid tumors. Clinical trials of CAR-T-based cancer immunotherapy for solid tumors showed that the efficacies are not as remarkable as in the case of hematologic malignancies. There are several challenges that researchers must face when treating solid cancers with CAR-T cells, these include choosing an ideal target, promoting efficient trafficking and infiltration, overcoming the immunosuppressive microenvironment, and avoiding associated toxicity. In this review, we discuss the obstacles imposed by solid tumors on CAR-T cell-based immunotherapy and strategies adopted to improve the therapeutic potential of this approach. Continued investigations are necessary to improve therapeutic outcomes and decrease the adverse effects of CAR-T cell therapy in patients with solid malignancies in the future.