海底管道总传热系数的研究与确定

以聚氨脂泡沫塑料为保温材料的双重钢管保温管道为例,结合实验方法,论述套管空气夹层的当量导热系数、保温材料的整管导热系数及材料老化问题,并给出了海底管道的总传热系数计算公式。

Temperature characteristics of InGaAs/GaAs vertical cavity surface emitting laser

The temperature characteristics for the different lasing modes at 300 K of intracavity contacted InGaAs/GaAs Vertical Cavity Surface Emitting Lasers（VCSELs） have been investigated experimentally by using the SV-32 cryostat and LD200205 test system. In combination with the simulation results of the reflective spectrum and the gain peak at different temperatures, the measurement results have been analyzed. In addition, the dependence of device size on temperature characteristics is discussed. The experimental data can be used to optimally design of VCSEL at high or cryogenic temperature.

Phase Transition for a Mixed Spin-1／2 and Spin-sB System with a Transverse CrystalField

The critical behaviors of a mixed spin-1/2 and spin-sB Ising system with a transverse crystal field are studiedby use of the effective-field theory with correlations. The effect of the transverse crystal field on transition temperaturesis investigated numerically for the honeycomb (z = 3) and square (z = 4) lattices. The results show that there is notricritical point for the system.

Density of Electron States and Volume of Solution of Hydrogen in SiC Alloys

The new reactor concepts are characterized by higher efficiency, better utilization of nuclear fuel and nuclear waste minimization. This approach means that it is necessary to continue a continued research and test of new materials in order to apply them in new reactors. In this study, the authors fbcused on the analysis of SiC alloys because, due to their particular properties, this alloy can be used in high temperature conditions where the pure silicon, semiconductor material par excellence, is inadequate to support them.

Low Concentration of CO Gas Sensor by Atomic Layer Deposition

In this study, Al/TiO2/Al2O3/p-Si was fabricated as a gas sensor. TiO2 and Al2O3 were grown by Atomic Layer Deposition method. The prepared film was tested in various gas concentrations at different operating temperatures ranging between 27 ℃ to 177 ℃. The sensitivity increases with increasing gas concentration and operating temperature which have a direct effect on sensing surface. The gas sensing mechanism could be explained with the surface controlled type based on the change of the electrical conductance of the semiconducting material. This mechanism is controlled by CO molecules and the amount of chemisorbed oxygen on the surface which is associated with temperature. Sample exhibits the basic parameters for gas sensors applications which are good stability, reproducibility and high sensitivity to CO gas which are. In addition, the response and recovery times are measured 19 and 26 s, respectively.

Lightweight Concrete Using Local Industrial By-product

Construction is one of the largest users of energy, material resources and water and it is a formidable polluter. One of the major materials used in construction is concrete and ordinary concrete contains about 12% cement which is a major producer of greenhouse gas in the world. The use of waste materials as partial replacement of cement in concrete reduces greenhouse gases, frees up land fill space, and reduces raw materials consumption. This contributes towards sustainable development, as in a sustainable society, nature is not subject to systematically increasing concentrations of substances extracted from the earth＇s crust. This research work explores the possibility of replacing some percentage of cement in concrete with marble sludge powder to produce lightweight concrete. This was achieved by determining the compressive strength and some hardened properties of concrete like sorptivity and carbonation with marble sludge. The results so far have been able to prove that lightweight concrete can be produced when some percentage of cement is replaced with this waste.

Kinetic Adsorption of Ammonium Nitrogen by Substrate Materials for Constructed Wetlands

Constructed wetlands （CWs） are engineered systems that utilize natural systems including wetland vegetations, soils, and their associated microbial assemblages to assist in treating wastewater. The kinetic adsorption of ammonium nitrogen （NH＋-N） by CW substrate materials such as blast furnace slag （BFS）, zeolite, ceramsite, vermiculite, gravel, paddy soil, red soil, and turf, was investigated using batch experiments and kinetic adsorption isotherms. Both Freundlich and Lang- muir isotherms could adequately predict the NH＋-N adsorption process. The maximum adsorption capacities of NH＋-N, estimated from the Langmuir isotherm, ranked as： zeolite （33 333.33 mg kg^-1） 〉 turf （29274.01 mg kg^-1） 〉 BFS （5000 mg kg^-1） 〉 vermiculite （3333.33 mg kg^-1） 〉 gravel （769.23 mg kg^-1） 〉 paddy soil （588.24 mg kg^-1） 〉 red soil （555.56 mg kg^-1） 〉 ceramsite （107.53 mg kg^-1）. Some properties of the substrate materials, including bulk density, specific gravity, hydraulic conductivity, uniformity coefficient （K60）, curvature coefficient （Co）, organic matter, pH, exchangeable （or active） Cu, Fe, Zn and Mn, total Cu, and Fe, Mn, Zn, Cd, Pb and Ca, had negative correlations with NH＋-N adsorption. Other properties of the substrate materials like particle diameter values of D10, 030 and 060 （the diameters of particle sizes of a substrate material at which 10%, 30% and 60%, respectively, of the particles pass through the sieve based on the accumulative frequency）, cation exchange capacity （CEC）, exchangeable （or active） Ca and Mg, and total K and Mg had positive correlations with NH＋-N adsorption. In addition, active K and Na as well as the total Na had significant positive correlations with NH＋-N adsorption. This information would be useful for selection of suitable substrate materials for CWs.

A robust self-healing polyurethane elastomer: From H-bonds and stacking interactions to well-defined microphase morphology

Self-healing materials have attracted considerable attention because of their improved safety, lifetime, energy efficiency and environmental impact. Supramolecular interactions have been extensively considered in the field of self-healing materials due to their excellent reversibility and sensitive responsiveness to environmental stimuli. However,development of a polymeric material with good mechanical performance as well as self-healing capacity is very challenging. In this study, we report a robust self-healing polyurethane(PU) elastomer polypropylene glycol-2-amino-5-(2-hydroxyethyl)-6-methylpyrimidin-4-ol(PPG-mUPy) by integrating ureidopyrimidone(UPy) motifs with a PPG segment with a well-defined architecture and microphase morphology.To balance the self-healing capacity and mechanical performance, a thermal-triggered switch of H-bonding is introduced. The quadruple H-bonded UPy dimeric moieties in the backbone induce phase separation to form a hard domain as well as enable further aggregation into microcrystals by virtue of the stacking interactions, which are stable in ambient temperature. This feature endows the PU with high mechanical strength. Meanwhile, a high healing efficiency can be realized, when the reversibility of the H-bond was unlocked from the stacking at higher temperature. An optimized sample PPG1000-mUPy50%with a good balance of mechanical performance(20.62 MPa of tensile strength) and healing efficiency(93% in tensile strength) was achieved. This strategy will provide a new idea for developing robust self-healing polymers.