期刊文献+
共找到3篇文章
< 1 >
每页显示 20 50 100
基于FANUC数控系统模拟主轴功能的改进设计 被引量:2
1
作者 沈钻科 《机电工程技术》 2021年第12期282-285,共4页
主要研究了FANUC0I-F系统数控机床采用模拟主轴的硬件连接和模拟主轴PLC控制程序的编制,改进和实现了数控设备使用不同的操作方式对模拟主轴进行调速的控制方法。针对使用模拟主轴数控机床的优点,确定了使用模拟主轴数控机床的硬件构成... 主要研究了FANUC0I-F系统数控机床采用模拟主轴的硬件连接和模拟主轴PLC控制程序的编制,改进和实现了数控设备使用不同的操作方式对模拟主轴进行调速的控制方法。针对使用模拟主轴数控机床的优点,确定了使用模拟主轴数控机床的硬件构成。从使用模拟主轴数控机床信号的定义、手动与自动工作方式下主轴正转、反转方向和停止进行控制程序设计。根据主轴加速和减速信号的组合原理,讲解了使用倍率开关调整主轴加减速度的PLC程序的编制和改进设计后使用按键开关调整主轴加减速度的PLC程序的编制。经过对模拟主轴PLC程序的编制与设计,实现了倍率开关和按键开关对模拟主轴进行调速的功能。 展开更多
关键词 PLC程序 模拟主轴 倍率开关 按键开关
下载PDF
浅谈数控车床实训中易出的问题及解决方法 被引量:5
2
作者 李健勇 《职业教育研究》 2006年第7期152-152,共1页
本文从编程、数控系统、误操作、机床本身机械故障及坐标系五个方面分析了数控车床实训中容易出现的问题及解决方法。
关键词 G00 G01 刀补值 进给修调开关
下载PDF
C-cut Nd-doped vanadate crystal self-Raman laser with narrow Q-switched envelope and high mode-locked repetition rate
3
作者 李祚涵 彭继迎 +2 位作者 郑义 杨野 寇晋华 《Optoelectronics Letters》 EI 2014年第6期423-426,共4页
In this paper, a passively Q-switched and mode-locked c-cut Nd-doped vanadate crystal self-Raman laser at 1.17 μm is firstly demonstrated by using Cr4+:YAG. Two crystals of Nd3+:YVO4 and Nd3+:Gd VO4 are adopted to ge... In this paper, a passively Q-switched and mode-locked c-cut Nd-doped vanadate crystal self-Raman laser at 1.17 μm is firstly demonstrated by using Cr4+:YAG. Two crystals of Nd3+:YVO4 and Nd3+:Gd VO4 are adopted to generate laser, respectively. With the incident pump power of 13 W, the average output powers of 678 m W and 852 m W at 1.17 μm are obtained with the durations of Q-switched envelope of 1.8 ns and 2 ns, respectively. The mode-locked repetition rates are as high as 2.3 Hz and 2.2 GHz, respectively. As far as we know, the Q-switched envelope is the narrowest and the mode-locked repetition rate is the highest at present in this field. In addition, yellow laser output is also achieved by using the Li B3O5 frequency doubling crystal. 展开更多
关键词 Frequency doublers Locks (fasteners) Q switching
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部